Search results

Anyone know where and how to get to the front zero on the clutch power shaft? I found the one at the rear of the mower on a pillar block bearing but can’t see the front one. I did find the one under my feet on the universal half shaft though. Any help would be greatly appreciated. Thanks.

I’ve looked at Bush Hog and Land Pride. Wow they are expensive. Any cheaper brands that are just as good or should I stick with the name brands?

I have two Ford tractors one that’s a 2810 and another that’s a 3910. Both are full of what looks like rust scale that flakes off and sits in bottom of the tank. The tanks are very hard to remove because of age. Is there away to clean these properly? I tried white vinegar with limited results. I...

I just started bush hogging with my new M7060 and noticed the cutter does not seem to follow the ground (tilt) properly. Draft control is typically used for soil engagement correct? With this said seems I want lever all the way back? What I don’t understand is sometimes when I lower the Bushhog...

Hello, I’m having a issues with the temp readout on my tach. It basically stays in the same position all the time where all my other Fords go all the way to cold position when key is turned on. Does this sound like a bad sensor?

So getting ready to pull the trigger on a new box scrapper. I’m looking at the 35 series of Land Pride and Southern’s HD version. The southern is 1/2 the price of the Land Pride. Is the Land Pride that much better? Also I need 78-80” if I want to cover my tracks. I want to cover my tracks...

I’m new to fully hydraulic shuttles so wanted to understand how they work better. I understand the shuttle itself but I’m not completely sure about the clutch. So my question is that is it just like a conventional mechanical clutch with plates or disk etc? Or other? Also, when I’m using the...

Yesterday had a chance to break her in a bit. She’s a joy to operate. Trying to get some hours on her before working her hard in spring. I’m ready for spring now though. [emoji16]

I know this has been discussed before but wanted to add a little more to the discussion. I currently have 3 Grasshopper mowers which I like a lot. I have a 325D, 725D, and a 900D. The 900D is by far my favorite as I have steep hills and the stability and traction is much better than the others...

Looking to buy one of these soon for mowing steep banks. Both ok or? Looking at a 25hp diesel and great reliability and traction. Thanks

I just took delivery of a MWFD M7060. Love the tractor but it very hard to shift, gear 2 runs faster than 3 and gear 1 and 7 seem to have two different speeds. For example gear 7 (1st gear H range) should run about 4mph at 1500 RPMs and sometimes it does. But then other times it runs 7.5 at the...

Guys, I have a 3910 tractor that I restored several years back and since 2018 keep having a strange fuel issue. So three years ago my fuel filter was getting clogged often so I drained the tank and the diesel fuel was a nasty brown color. I decided to clean the tank with vinegar which got out a...

Hello friends, I recently had a pond management service come in and spray one of my ponds for duckweed. They told me the chemical was harm harmless to wildlife but within about seven days after they sprayed the pond now has hundreds of dead bluegills all around the edges. Obviously the chemical...

I have a farm that consists of alot of field/wood edge line. Probably close to a mile in total. The problem is that now I edge everything by hand which is very time consuming. The way it works is limbs from tress slowly grow out over edge of fields protecting some of the understory which I...

For some reason this has happen really fast but not sure how to deal with it. Some kind of chemical I guess?

As the title says I believe I may have a starter going out on one of my 10 series Fords. For the past year sometimes the starter turns over perfect then others there’s only a cluck then nothing. Key off then back on and it might turn over or might “clunk” again. At first I thought I had a bad...

I have about 7 acres that’s in grass and we currently mow but is somewhat rough. It was used previously as tilled agricultural land so still has some small ridges that are close together which makes mowing not so fun. Even on a ATV or UTV it’s a bouncy ride. Would you guys think a power rake...

I bought this tractor last year and discovered it has a brake issue. So it’s a 4x4 with cab and front loader. The issue is the right brake seems to grab a bit (not always) and the pedal is hard with very little movement. I can tell when this happens as the brake is engaged some holding back...

Guys, I bought this tractor knowing it has a brake issue but the price was right. So it’s a 4x4 with cab and front loader. The issue is the right brake seems to grab a bit (not always) and the pedal is hard with very little movement. I can tell when this happens the brake is engaged some as...

I’m looking to clear grown up fields and have a 80hp massey cab tractor and extra heavy duty 6’ land pride brush hog. The growth is 5-7 years and some of the trees are up to 4” in diameter. Would I be OK using what I have or should I really be looking at a skid steer with front heavy duty...

So I have a lightly used 6’ BH 286 cutter. Never had issues with it but today tried to slide the quick coupler onto the pto shaft of the tractor. I can get it started to where the first de-tents are on the shaft but then it won’t go any further. The pto is well greased and I don’t see any...

So we have about a 3 acre field that is currently a mixture of grass and weeks that we mow at 3.5” high. Problem is it’s a old tobacco field that still has some of the ridges left in place from the previous owner. They are not terrible but enough we need to mow slow or it makes you sick going...

Can anyone enlighten me on what the red tube thing running up along side of the hydraulic cylinder? Looks like it might have broke off at some point as someone used rope to re-attach it. Thanks

Im looking to buy a new top link for a tractor and see a huge difference in pricing. $320 for cat 2 from New Holland and just over $100 for a equivalent aftermarket. Are the OEM versions of better quality or perform better? $200 seems like a huge difference.

Anyone have or had one of these? Just curious how well they are made and if they are reliable.

Hello Gentlemen, Ok so I had a previous thread where several of you provided suggestions and or ideas which I greatly appreciate. All this info led me to a trailer I located today. Its a PJ F8 24' deckover with 4ft dovetail plus easy lift flip-over style 4ft ft ramps (not monster ramps). I...

Gentlemen, I’m looking at buying a new 22’ deckover to service our customers larger tractors and need some advice. Currently we are looking at trailers with 3’ dovetail designs and 60” ramps. Does anyone have experience with loading tractors with attachments like bushhogs and disk harrows etc...

Anyone know if the steering and front end are stout enough to fun a front loader? The reason I ask is this is before loaders were popular and a lot of tractors had issues with them. I bought this tractor for a very cheap price last year and just replaced the steering sector. Worried now it...

I have 3 ponds and 1 of them has a really steep bank that has to be hand maintained. Does anyone have ideas to what I could plant that has the following attributes? - keeps trees from sprouting and growing -requires little mowing -has small root system to protect from penetrating dam. Thanks

I have a opportunity to purchase one of these in 6ft. They are asking $5k. Anyone have any experience with this company?

Good morning. I recently purchased a new farm and it has a house with a wood burning fireplace. Fate would have it that a huge red oak was blown down during a storm back in late November. So I purchased a new Stihl 362 CM and have been cutting it up for firewood. So this is all new to me and...

I’ve asked this before with no luck but wanted to try again. So I’ve owned 7-8 Ford 2810-4610 tractors since 2007 and have come to realize that many develop a strange engine vibration from around 1500 rpms- 1700 or so. I do have a 2810 and 3910 that don’t have this issue however. So my...

I'm looking for some assistance in setting one of these up. I've been cleaning, repairing and greasing a new to me dual row 309 and finally have it ready to roll. Purchased it earlier this year and did one trial run a couple weeks back. So in setting this up I noticed that the front of the...

Does anyone know if these are good tractors? I have no experience with them but have a opportunity to buy one from a friend of mine. Would love to hear some feed back if anyone knows anything about them. It’s a 2011 open station with loader and MWFD. It currently has just over 1100 hours on...

I’m trying to change out the starter on my 39 Tian and see there are three mounting bolts. Two are real easy to get to but the one in the rear is unbelievably hard Do you even get anything on it. Has anyone done this and know a way to access this bolt?

So both of these offer a diesel motor at 25hp. The difference is the 900 comes with. 1.3 L motor with 80 torque vs a .89 L with 55 torque. Also it appears the larger motor runs a 2600 rpms while the smaller version runs at higher 3600. So my question is would the 1.3L really perform that much...

Hello, I’ve located a 7ton grain bin and would like to put it on my 84” wide trailer that’s 21’ in length. The bin is 16’ tall and 6’ diameter. Anyone ever done this before?

So I’ve been working on this tractor for several months since I purchased it last year. Have it about ready to go now except finding correct rear stabilizer bars per a separate thread plus a issue regarding grass and weeds wrapping around the drive shaft. So speaking of this does this cause...

Anyone know where to get stabilizer bars for my tractor? Dealer seems to be lost on this. It’s a 1984 or 85 Ford 5610 Cab tractor MWFD. I would entertain a newer adjustable system if available but the old flat bar style is fine too.

Guys, My wife and I are in the middle of researching a better to best type of materials and design for a small 8x10 or 10x12 storage shed for our local high school. We will be donating it to the soccer program and want to have it made to match school colors of red, black, and white. I like...

I did't get a response my earlier thread so going to try again. What are the differences to these tractors? Should I be scared of any of them? Trying to decide which way to go. Thank you,

My neighbor has one of these and has offered to sell it to me. Are they a good model? Plus's and minus of them? It has the factory loader and has low hours. Really like the looks of it just don't have any experience with Case. Also, did New Holland make a equivalent tractor in blue? I know...

Buddy of mine has one with low hours. Thoughts? Or would you buy something else? Need it for bush hogging and planting food plots.

I have 3 ponds on my farm and the previous owner just let trees start to grow on them. The original pond has 50-80 ft trees on the dam which I believe leaks as it never fills back up to to overfill pipe. The other two ponds have 5-15ft trees on both sides of the dam. Should I remove them...

I’m new to Mahindra so don’t know much about them. Mostly Fords and Massey Ferguson‘s in my past. What is the overall experience from Mahindra customers? Currently I’m looking at Kabota Mahindra in new Holland. I know Mahindra tractors are fairly heavy and built a sturdy but how was it overall...

Gentlemen, A year back I purchased a large tract of land consisting of forest land and about 60-70 acres of old tobacco fields. Some of the fields have now grown up but we still have some 9-10 acres around the house that have been mowed for the past 20 years. The problem is that these larged...

I have a massive 461 with the Perkins engine in the valve Clarence has never been checked. Engine has under 700 hours on it but thought I might have it checked. Looks to me that someone hard to get things removed in order to check the clearance so I'm wondering is this really worth doing...

I'm getting ready to buy a 4.6ton grain bin. It's 14ft high and I'm having a friend deliver me shelled corn in bulk. But he doesn't have a small auger to transfer the corn to my bin. What is the best way to do this as cost effective as possible? I will only fill it twice annually.

I'm thinking about buying one of these. It holds a little over 100 bushels. Can anyone share with me how these are assembled?

It was dark when we finally arrived at Farm so will start checking it out tomorrow. More pics to follow.

Guys, So when I change fuel filters do I have to bleed entire system all the way to the injectors? Or is there a way to bleed just to the pump without having to do injectors too? This would save time plus added engine cranking etc. Reason I ask is that I thought someone mentioned a way to do...

Guys I spoke to Athens today and they are telling me that their model 97 offset is too much machine for my tractor. This is in the 7'6 size. I need this width to cover my tracks so I really don't want to go smaller. From what they're telling me the tractor will pull it is lifting the disk...

Just as the title says can someone explain to me the differences in these two? I'm looking for the best performing disk with weight not being an issue. A 7.5' would be ideal size for me as I'm running a 5610 MWFD cab tractor with loader. Thank you.

Guys, I'm looking at a used RCF3672 Land pride cutter which is rated for 60-190hp tractor. My 5610 is rated at the low end of 62 pto hp. Would like to have the 4" cutting capacity but can my tractor handle this much cutter? Thank you

I just purchased this tractor. A couple questions. I have a 14k trailer. Will it handle this tractor? I think so but I'm having a hard time finding the actual weight. Tractor data says over 9k ballasted. This tractor has Cab, MWFD, ballasted, and a loader. Also, can I run 18.4x30 AG tires...

Guys, I have a big issue and need some good advice. Several years ago I purchased a Ford 3910 tractor that was made in 1988 with very low hours. Since then I put about 10 hours on it and have kept it in a building but only ran it once per month for 10-15 minutes. After storing it and not...

This is my fuel cap on my 3910. What is the stuff on the cap? Looks like rust? Maybe it is but how would rust form with diesel fuel? The entire tank is lined with it and fuel shut off valve keeps getting clogged up with small particulate. Fuel is orange color too.

Getting ready to buy a trimmer. Any thoughts on these two engine designs?

https://www.ne-equip.org/wp-content/uploads/2016/05/2016_Survey_Report_Final.pd_.pdf

Here is the 2016 equipment dealer survey. I knew these mowers were good but didn't know they the best. https://www.ne-equip.org/wp-content/uploads/2016/05/2016_Survey_Report_Final.pd_.pdf

I found a 850 4x4 that runs out nice. All original and never painted. About 2k hours and engine was recently overhauled and runs great. Cranks well in cold weather and hardly smokes unless hammered on. My question is what size disk harrow and bush hog can I use on this tractor? Also what is...

I need something to plant food plots for deer. Will do corn, soybeans, and grains. Will one device do all? I will disk and prepare soil first and have a budget of $4-5000. Thoughts?

I'm looking at Kasco drills. Are they any good? Looking for a good product that well supported. Thanks

Are these good tractors? Reliable? Looking at one with 1200 hours, no cab and MWFD with loader? If this is a good tractor pricing? Thanks

Gentlemen, I have a opportunity to buy one of these. Farmer needs to sell it and says cranks in cold weather and runs good. It is 4x4 with a cab. I'm told not many of these were ever shipped to the US and maybe not any as new. Just not sure but I'm a old Ford guy and love the smaller 10...

Reason I ask is that I have both dealers close and believe them to both make good products. The property I just purchased had a 20 plus year old Grasshopper 60" that was still running strong with minimal repairs. Are they still a good supplier and how do they compare to Gravely? Thank you

Guys, I see the new 70 series has a smaller engine, more emissions stuff "tier 4" and is over 1000lbs lighter? How and where did they remove so much weight? With all these negatives I'm no longer considering them and am very disappointed in NH. May look at a used one like a 65 or 75 if I can...

I need a 60 hp tractor and have narrowed it down to a 2005 MF 461 or new Workmaster 60. Normally I would buy new when paying about same price BUT with lighter weight tractors, smaller engines and more emissions crap I'm thinking I might go used. The 461 only has 425 hours and looks like new...

I have a 2004 461. They didn't sell a lot of these in North American. Should I be worried about part availability or will aftermarket kick in later on. I love this tractor just a little concerned about parts if I need them down the road. Thank you.

I have a 2004 model that's been great. One concern I have though is that this tractor is getting older now and I'm wondering how hard it will become to get parts. Will aftermarket continue making parts for low volume models? Very few 461's were sold so not sure what to expect. Thank you,

Would like to hear your review if you have one. Thanks

Ok tell me what you recommend. No cab, MWFD for bush hogging disking and loader work. Just interested in very reliable and comfortable. Thanks.

I found one local that has 500 hours. MWFD wo/loader. Looks like it's in awesome shape. Has been in a barn most of life and is a 8/10. Super nice condition. Any idea of value? They asking 21k

I just purchased 270 acres and want to finish cut about 10-15 in grass. It's already being cut now by a Grasshopper mower. Takes him 1.5 days to cut it at 8 hours per day. So if I were to buy the perfect or best equipment for this type job what would it be? Terrain is rolling with some...

How do you guys like these tractors? I think I want a 75 but wanted to check with everyone to be sure. Thank you

Can anyone provide some feedback on this line of tractors? Are the reliable? Designed well etc. Thank you

Can anyone answer this? Thanks

Are these good tractors? If not which NewHolland would you recommend in this HP range.

I'm looking to add snow guards to my metal roof barn. The metal roofing has a Kynar 500 paint and my contractor wants to use the SnoGem polycarbonate ones that adhere to the roofing. He says this protects against rust from metal to metal contact. Thoughts on this?

A friend of mine has a 2006 or so John Deere 990 and has never serviced anything other than the oil and filter. I know its way overdue so trying to help him out. Anyway, i've changed coolant, air filters etc but am now on the fuel items. So after looking at the manual it only mentions a rear...

My weight bracket broke off front of my tractor. Now what? Is it repairable?

Well haven't been able to enjoy the new barn much before first major issue. Last month a fitting burst and dumped 358,000 gallons of water into the building. This is because I was traveling away for close to 30 days before noticing the issue. Will have to repair a few things but thankfully...

Hello, For several weeks now I can no longer start new Threads from my TractorByNet app. I can respond to threads but not start new ones. Basically I get a response of "choose a thread prefix" and app locks up so I must close it out. Any ideas how to correct this? Thanks

Wasn't sure where to post this but for several weeks now I'm not able to start a new thread from my IOS app. When I do the app just locks up. Anyone know why this is? Thanks

So I've posted on here regarding a 20' 14k equipment trailer that I bought new in 2011 that's never been right. From tires that blew out with less than 2000 miles, suspension issues and a strange vibration issue that know one could seem to resolve. Based on this I decided to buy a new 22' PJ...

Looking for ideas on this. Engine cranks very fast but has a slight miss sensation that translates to vibration around 1600 rpms. I replaced injectors but didn't change anything. Does this sound like a pump or timing issue?

I'm getting ready to buy a new bumper pull PJ equipment trailer. I've used 16-18' trailers in the past that handle my 8000lb load very well. Truck pulls good without issues. Then I bought a new 20' Kaufman that has been a nightmare and pulls bad. Jerks truck and way more vibration than the...

Which is best overall? Thanks Sent from my iPhone using TractorByNet

I called him last night as it's been 4 days and he didn't cut it yet. From what I've read needs to occur about 4 hours or just after its setup some. Now he's talking about doing it several days later. What should I do? Is it ok to still do it? Thanks Sent from my iPhone using TractorByNet

Just as the title says. I liked the color of the Benjamin Moore "barn red" stain but just realized its only a stain and offers no weather protection. The Behr stain plus weather protection would be great but their red colors are limited. This is going on a 50x70 barn with new rough cut...

For some reason I can't start a new thread from my app. Also can't upload but one picture or app locks up. Anyone else having this issue? I deleted my app and reloaded it but no luck????

I'll pay a premium price for these if anyone has a set. Need full set of 5 and want the OEM style set. Thanks It's like this set.

So this brown crusty stuff is all over the inside of the cap and lip of the tank. It's my only tractor doing this. Thoughts?

Hello all, I'm having a friend of mine rebuild the engine in my 4000SU. As best we can tell she has around 10,000-12000 hours on her and the engine still runs but little hard to start when cold. I've decided to go with dry sleeves vs over boring just to protect from pinholes etc. I plan to...

It's a 40x70 with 12' shed and 12' ceilings. Poured foundation with popular siding. Will have upstairs guest quarters and extra storage. Barn will be heated with gas heat and fully insulated. This forum was a big help in putting all this together. Thank you.

Looking at pine or popular for barn siding. The house was built in 1800's and still has original popular siding so thinking of using it again. Thoughts for good and bad please!

Doesn't have to be wood but I like the look of these. What I'm hoping to do is paint it similar to the red door. Barn is wood but I was planning on metal doors. I could go wood too though. Building is 70x40x12. Garage doors will be (2) 14x10's in front and (1) 10x10 in rear of building...

I have a issue. My contractor screwed up and poured the walls so that two garage doors are on same side of barn when they should be on each end. I guess he can cut out those sections but when he re-pours will it bond correctly to what has already cured?

I'm in process of building a new barn. I'm looking at white pine vs cedar siding. I know cedar is better but limited supply in Ohio I think. Anyone know the cost to have siding shipped in and is it worth it over white pine? Thinking of doing board and batten or just using a vertical 6 or 8"...

So I replaced my fuel sending unit and noticed it's now leaking. I take it back out and find a possible issue. The sending unit goes into the tank first then you place a rubber seal over top followed with a metal ring that rotates in to lock all into place. The problem is there are exposed...

Have a friend that inherited his family's 230. I think I'm correct on the year. What would this tractor be worth? It has a little over 400 hours and original paint. Thank you as I'm trying to help him sell it.

What companies are best known for quality? I bought a Kaufman and it's junk so moving on to a quality product but need advice. Looking for a 14K 20' equipment hauler tag along. Thank you

I'm in need to rebuilding injectors for my 4600. If I go new is there any difference from OEM vs aftermarket ones other than being much cheaper in price?

Ok I think I have a issue. Let's start from the top. I bought this tractor and seems to run and crank very well. But I first did a coolant flush and got rust colored coolant out. Filled with clean water plus radiator flush ran per directions and got more rust coolant out. Did again and more...

So my 4600 runs smooth except from 1600-1800 rpms. Anything above 1800 is fine also. Any idea what could cause a vibration in this 200 rpm range? Do these engines normally run this way. I know it's a 3 cylinder but the vibration is a little uncomfortable so I end up running below 1600 or...

I'm looking at a used ford 3910. One thing I noticed is that the clutch pedal engages in a pretty high position right before full up. Is this a sign of a lot of clutch wear or is that when it engages quickly coming from bottom up?

I'm trying to change the coolant in my tractor. I have located the radiator drain but not engine block. Can any one help me locate it please?

I Have a Ford 4600 that to lift a implement you have to go way up with the control before it starts to lift. Maybe 3/4 way or little more. Lifts fine other wise and no hiccups etc. is there a way to adjust it so it starts to move sooner. I have been on several of these old fords and this is...

I Have a 1980 Ford 4600SU and the engine lopes a bit first few minutes after starting when cold. It's a diesel. Engine runs great afterwards and always cranks fast in cold weather. Just replaced fuel filter and both air filters. Thanks

I just purchased a used but very nice BH286 bush hog. I was trying to loosen clutch to reset it and realized its froze up. Anyone ever take one of these apart thats froze up? Just curious as to what to expect. Thanks Sent from my iPhone using TractorByNet

Just picked this up last week. Met the owner at his house. He bought it new about 9 years ago only mowing a 2 acre field behind his house using it like a grass cutter. He owns 5 acres but only little over 2 are grass plus house rest is woods. Had bought a new 50 hp deere to run it too...

I need a new pump and my 4610 has always had faster and easier steering. Did they use the same pump for both or did they increase flow on the 4610s. Would like to use a better pump if possible. Thoughts? Thanks Sent from my iPhone using TractorByNet

Im getting ready to buy a new cutter. Im looking at woods brush bull, bush hog squealer or now BH16, and Land Pride RCR or RCF "cant remember" 2072. I know all are good but which offers best parts and service support? Im a little worried about BH as i don't like the new weak tail wheel...

Anyone have one of these tractors? If so please give your review both positive and negatives.

I have a infrared thermometer and want to check my Ford 4600 engine temp. What area or areas do I check to get the best reading. Right now the manifold and just above the manifold on the engines reads about 220-240F.

Ok so our new home is almost finished so its about time to pour the driveway. This in VA so seeing some freezing temps. The contractor says no worries as they use additives to keep things from freezing. So my question is does these additives hurt, make weak, or damage the concrete long term...

This is the back of a ford 4600 operations manual. Can anyone tell by these numbers of the year it was produced?

Guys, I put a new thermostat in my tractor and the temp gauge needle is barely in the green when bush hogging. What do you guys see for your tractors? Does this sound normal?

guys there are 3 thermostat options for my tractor. which one is the standard?

Well I'm a little concerned and need some advice. I have a farm in Ohio and am in process of building a barn on slab foundation. Problem is that it was supposed to be poured in October but never happened. Now its getting very cold and Ive been told cold weather is bad for pouring concrete...

I have 10 or so very old timbers 20 footers or so from around 1890. What is the best way to clean and prep them for using in my new homes man cave? They are hand hewed too. I just had them heat treated to kill bugs inside. Thank you

Sorry second thread but screwed up title in first one. I have a diesel 4600. It idles at 850 -900 rpm's but should be at 600-700. How do I correct this?

I have a 4600 that runs at 850 rpms at idle. In reviewing my manual it should idle at 6-700 rpms. How do I adjust this? Well title was suppose to say 4600 not 4609. LoL!

My family and i have two fairly new equipment trailers from Kaufman. They are ok for price I guess but both jerk and bump the truck alot compared to others I used. Both are rated about 14k gross weight. One is a 16ft and the other is 18ft. So I let a friend use the 16ft and my dad had 18ft...

Anyone know what causes the clutch to be overly easy to push the pedal down? Seems to work ok but very different than my 2810,3910 and 4000 SU.

Guys Im building a board and batten 40/70 building with 9 or 10' garage doors. Problem is i want something that complements the building. Does anyone know a supplier that makes nice doors to go with my building? Thinking 9' x 14 or something close to that. Thanks

Guys, I have just given my builder a green light to build a 40x70x11 equipment barn. It will have a poured foundation, metal roof, and board and batten siding. I'm sure I will have more questions but for now I wondering how to keep moisture out of the building. This includes keeping the...

Regarding Ford Tractor Coolant (diesel models) Ive been researching different coolants for past few days and thought I would share my findings. As you know there are many types of coolants today. Some are ok for our tractors and some are not. This is due to being incompatible with rubber...

Guys I'm considering buying a "supposedly" low hour Ford 4600. Apparently, it was used in a very small field to mow a couple times a year over the past 25 plus years. For the past 3 years it has just sat in a barn and has not been cranked. I have not looked at it yet in person but will do so...

I was unable to find this on the net last week so thought I would post for everyone. May help me again in the future too. Lol

Im looking at a low hour Ford 2910 that is in great condition. However it does not go above 1500 RPM. The engine runs perfectly and very smooth just wont run up to rated engine speed of 2000 RPM. Before i buy it does anyone know what might cause this?

Anyone have any specs on this new mower? Just got word this one is in production now and will take the place of the 290 series.

Just enjoying a beer and freshly waxed Ford 2810. Work is done so now time to relax and enjoy. This tractor only has 445 hours a d is all original. Anyone else like Ford tractors this much? My wife thinks I'm crazy.

The glass on my Ford 3910 tractor tach is very hazy from being out in the weather. Is there a way to restore the finish?

We have torn down two barns that are 90-100 years old and removed as many hand hewed timbers as possible. A couple of them are 21ft long and as new but most are weathered and have minor rot and or bug holes toward the surface. All but 2 are 8x8 oak post and the 2 are 11x11 oak. How might i...

Im looking for a new 6' cutter. Looking at all name brands like woods, bush hog, brown, land pride, rhino etc. Currently ive had or used BH squealer, BH 286, king cutter and deere mx6. The Deere mows the best but has had the most problems and is the newest. Its a strange design as it has a...

I need a medium duty cutter under 1000lbs. They crazy thing is that all manufactures are turning the medium duties into near heavy duty units. They offer smooth decks but have very high side walls requiring more steel thus increasing the weight. I have a BH 286 which i love but you no longer...

I have a 461 that slowly overheats when bush hogging grass. Takes about 15 minutes to do so. 6ft cutter, radiator is clean and full. New water pump supposedly installed. Any ideas? I hate to take to dealer but no idea how to proceed. Thanks

Our family farm was started around 1850. During this time there were 12-14 barns and 1 house. Most barns deteriorated due to bad roofing. But were talking about stuff that lasted 100 years and some longer. We still have 4 barns left and the house which are all sitting on stacked 36"x36x12"...

Im getting ready to have a barn built this spring. Problem for me is the type of materials. My family has owned our farm in Ohio since around 1850. All the structures have always been wood and i really want the new barn wood as well. BUT i know metal last longer so am i making a huge mistake...

Hello, We have a farm in Noble county Ohio. Im looking at a 40x60 pole barn with either wood or metal siding. Still undecided. Who builds quality buildings and use good materials? Im looking for good paints on metal and quality stuff. Thank you

Ok im going to paint my 3910 ford tractor. Im planning to use Omni AU urethane base clear. What steps should i use to clean and prepare metal? Also what primer should i use. I heard a etching primer is the way to go. Also using all Omni line products. Thank you

So is Urethane paint good? Does it stick well with the right primer? Looking at a PPG Omni. I think i have a good match in both blue and light grey. Also thinking of using a clear too on sheet metal and wheels for extra protection. Thoughts?

Just tried it out and man does it cut deep. Sucker is very heavy and all my Ford 3910 would want. Really built well and leaves a smooth bed of dirt behind her too.

I have a late 80's 3910 tractor with 13.6x28 tires on 12x28 rims. I also have two OEM service manuals (1983 and 1988) that show this tractor having a optional rear tire size of 14.9x28 on 13" rims. So my question is why does no one make this 13" rim? I have called NH and searched the web but...

I checked the power steering oil today and its low. Unfortunately my NH dealer is closed tomorrow. Is there another fluid that is a duplicate at Napa or autozone? The manual says i need M2c-41b or m2c-159-a or -b. Any ideas?

Guys, I want to really clean up my Ford 2810. However, the tractor has low hours and the paint is like new so i want to maintain its condition as much as possible. This tractor will be stored most of the time and only used once a year. I will be cranking it every month or two but thats about...

Anyone know what is involved in tearing one of these down and replacing all seals?

Guys, My 461 has about 450 hours on the clock and it overheats while brush hogging. The radiator looks clear but the fuel cooler has some grass etc in it from the previous owner. Not sure why you cool the fuel anyway but could that be the issue? Other issue is the stuff is caked in there...

Ive been looking at Morton and Lester buildings online. As i understand it Lester is about 25% less in price and still has alot of the features similar to Morton plus has a good paint warranty for their steel. Has anyone tried them and if so what are your experiences? Also are there any...

Guys, I'm planning to build a new 50x60 pole barn this fall. This is my first so i know very little about them. I am looking at everything from the standard kits to Morton buildings. This will be built to store equipment, deer cleaning station and some upper level storage for smaller items...

Guys how does the 286 cut grass compared to a 72" squealer or Hardee 1072? I like the specs of the hardee alot but the blade tip speed seems slow. I need something under 1000lbs but a decently stout cutter for the occasional rock. My tractors are fords 2810 to 4610's. 32-52 pto hp. What do...

OK so yesterday i serviced my new to me 1989 Ford 2810. Changed oil/filter, coolant, fuel filter/water separator, 2 new air filters, transmission oil, hydraulic oil / filter etc. The engine oil looked ok, fuel filter looked decent but the fuel separator was full of very black fuel with small...

Guys i have found one of these with 500 supposedly (gonna look tomorrow) original hours. This is a 1 owner tractor and husband died so wife selling it. Whats it worth if in good condition like she says? This tractor should look very good and have original tires, everything feel like new and...

I have a 1971 4000 su with high hours that runs rough (vibration) during certain parts of the rpm range. It's done this since I bought it in 04. I have totally rebuilt front end and alot of other stuff but nothing engine related. The tractor starts well even in very cold weather too. So does...

Double post sorry

I need 4 tires for my 3910. What type 14.9x28 do you guys recommend. I will use it for disk harrow and bush hog. Bias tires only please. Thanks

i'm rebuilding a my SU tractor and need to replace both rear drag links or the long portion of the link. Can someone measure their tractors links or provide me with the OE spec? I need the measurement from the end of the threads (close as possible) and to the CENTER of the draglink end where...

OK i have a 1971 Ford 4000SU that turns so tight it contacts the radius rods and is wearing on them. Can someone help me on how to adjust this out. Currently i have the tires just a little wider than stock and i'm running 7.50 x 16's which is one size larger than original. Also the 7.50's x 16's...

I have a 71 Ford 4000 that the governor seems not to work correctly. During load like running into higher grass bush hogging the tractor loses power quickly which is different than my newer ones. Shouldn't the governor pick up a little to handle the increased load? if so what would cause it...

i'm looking to rebuild my Ford 4000 engine and wanted to see if someone can help me understand all that should be looked at, replaced or rebuilt while i have the front of the tractor apart. Currently, i plan to completely rebuild the front end steering bearings, link ends, center main bushing...

Anyone have or had a Ford 2810 and can tell me how well they do with a 6ft bush hog? I have a Ford 4000SU with tons of hours and has lost some power so just curious how a low hour 2810 would do with a bush hog squealer 6ft cutter. Thanks,

Anyone have an idea of what one of these is worth? Tractor has about 950 original hours and looks great. Drives like a new one and front end is very tight. All original and no aftermarket parts. Thanks,

I have a 1971 4000 SU with a gazilion hours on it and the engine is finally starting to loose its power. I'm a good ways over 10,000 hours so figured its time. When i rebuild it should i overbore or should i use sleeves? I've heard both ways for these engines but want to do it the best not...

Anyone know how to fix this? I found two problems on my tractor. One is the differential lock / foot pedal is stuck and will not depress down. The other is the 4x4 light does not work but the tractor does go in and out of 4x4 easily. Could it be just a bad bulb. Any help would be greatly...

Ok so my loader works great except it has no down force. Float position works good but for down force it normally lifts front of tractor with no issues. However, now it won't even try to lift the front end. Anyone have any suggestions? All other movements on the loader work great. Thanks,

Well got to try the tractor out for the first time this week and man its nice. The 201 perkins engine is so smooth and the low end grunt is amazing. I've ran a few of the new compact tractors that must run high rpm for power and there's no comparison. My 461 can actually idle and run in the...

I just had my dealer install this used loader on my MF 461 tractor. The problem is there is no down force on the loader. I think everything else works fine. The loader seems a little slow but maybe the 461 has less flow than my friends Deere 990. Anyway, what could cause there to be no down...

If you have one of these tractors how do you like them? I'm ready to try one out next week and just curious if they've been good tractors and how they operate. Thanks,

hello, i have a massey 461 4x4 and looking to set the tires up a little wider. does the centerline point of the front and back need to be exactly the same?

Hello, I need to adjust the wheel width on my tractor but am looking for recommendations as to how wide I should go for hill work. Now the tractor is set up 56 inches centerline to centerline which is slightly more than how it came from the factory. I will be bush hogging and will sometimes...

Can someone explain advantages and disadvantages of the two? Looking to buy but don't know which way to go. I do small 1 acre wildlife food plots. Thanks,

I found a tractor but want to see what year and date it was produced. Anyone know how to find this? The serial # is 9852EN 15012. Thanks,

Ok i'm new to loaders and have located a 1055 loader for a Massey 461. My question is if this loader came off another 4x4 Massey tractor can the same mount be used or is each mount specific to each tractor. I know the loader is the right one just not sure about the mounting system. Please let...

Hello, Looking to buy one of these tractors (2006 model) and my local dealer just received one of these in awesome condition but no loader. Tires have 70% tread left and the tractor has 400 hours on it. Can someone tell me what its worth so i don't get taken? Its a one owner unit that was...

Anyone know which of these is ok to buy and which is not. I'm looking at the 451 and 461. I'm also looking at the 543 and 561. I've heard to stay away from the 451 as they are made in Brazil. Does this go for the 543 too? I'm assuming so as they are basically the same tractors unless...

Guys i need some help. I have a 1998 3930 with only 217 hours thats in as new condition. I love the tractor but i haul it around some and work in somewhat tighter spaces (in and arounds woods and trees) and was thinking a shorter wheelbase and 4x4 tractor might be the ticket. The 3930 rides...

Well I'm in the market for a new tractor and have always had the older iron with torque motors low rpm tractors. I've even driven newer masseys 563 model and they just pull like crazy. Now i like the Kubota cause they are cheaper and have good reliability. But from the tractors i've drove i...

I have a 1998 NH3930 w/192 engine with turbo and when it gets hot sometimes it must cool down somewhat before it will re-start. Also, when i turned the lights on one time while going down the road it died. I immediatly turned them off and it went right back running. Keep in mind this tractor...

I have a 1998 NH 3930 with 160 hours. The serial number tag under the hood shows a 3.2L turbo engine with 60 gross hp. Can anyone tell me about this engine? i would like to know the PTO hp and were can i find further information. There seems to be very little info on these engines and even...