hydraulic

I have two kioti hydraulic oil filters T4125-38021 , unopened and still in bags ... The dealer sold me these and they were incorrect for my model kioti tractor, I didn't know until maintenance time. The dealer is 1100 miles away and hasn't responded to my request for exchanges

Ive been reading here and on the internet that some owners turn up their hydraulic pressure on their 2520s been thinking about doing that any of you owners had done this? I check mine and its 2475psi thinking about going to 2700 will I break something or blow seals out with 200 more psi thanks

Hello all, Anyone with any exp with Iseki tractor ? I have a slow leak in a few spots, anyway need to top up hydraulic fluid. Seems there is a dipstick in centre console area behind shifter and a bolt type plug nearby, however the tube you can fit in there is a bout a quarter inch ...

I've got a Ford 5030 shuttle shift that is having an issue with the hydraulics I can't seem to figure out. The transmission shifts great, and the power steering works tolerably. The loader and 3-point hydraulic are very slow and jerky. The loader runs off the rear remotes supplied by the engine...

Hi all, I have a 2007 3820i with a BL20A FEL. Does anyone know the recommended hydraulic pressure setting. I think mine is off and new to adjust. Thanks

What filter are you us for the smaller hydraulic filter on the left side of the engine (looking from seat)that is readily available? Also, is this a low pressure filter? NH part number is SBA340501030 (says it has a bypass valve), I couldn’t a cross reference on Baldwin Filters site that is...

My 1445 has 1725 hrs and the deck will not stay float . It has a danfoss hydraulic control valve . I am not sure if or how to adjust the detent to keep the deck in float

Hello this question has been asked a million different times but a lot of them are conflicting - what is the latest advice on what fluids to use? In particular, my tractor has two pumps, one for the steering and one for the loader etc. Should I use an ISO 46 in the steering and a UTTF in the...

So, I’m gearing up for the first service this year on the 4820H. It may be a smidge early in hours, but 2 years in I feel like doing it. So, I have Rotella T6 for the motor, but I came across Triax Agra UTTO XL fluid for the transmission. Also considered the Shell Rotella HD oil. Does it...

The loader jerks really Bad when the oil is hot . I have replaced the pump, loader control valve, relief valve, change filter and oil ,replaced all suction hoses on suction side of pump ,changed the quick couplings and switched the hoses on the lift and replaced the cylinder packing . Installed...

Seems I need to replace a hose on my GC1705's FEL (DL100)... part SL103366. The tractor/FEL is around 10 years old, and is stored outside. Should I be looking to replace all the hoses at this age, or should they generally run longer? Is there a standard replacement interval? Is there much of...

Hello all. Well i was very excited to get my first tractor this weekend(I have only had skidsteers in the past.) Saw a great deal on a RK37 shuttle shift with 240 hours and I jumped on it. Guy said it had no leaks and I didn't notice anything while i was checking it out, but it was in the...

I have a Long 560 tractor with a hydraulic leak from the transmission case. The drain plug and two holes in line with the axles and drain plug are on the bottom side of the case. One hole is plugged with a bolt and jam nut. The other hole is wide open and the parts manual does not show anything...

A friend had a hydraulic leak on his 2350 and after removing the hood we discovered split/rotted small hoses running from what I assume is some sort of surge tank just behind the radiator. The tank is about 8" diameter or so and has a T fitting on top with barbed nipples where the two lines...

Removed the front end loader from 1025r. Re-installed 2 hours later. Now, when I try to tilt the bucket down, it comes up. Hoses are connected properly.

Does anyone know how much hydraulic fluid a 2610H holds? The manual doesn't say and when google it I see anywhere from 2.9 to 12 gallons. Here what in the manual and it can not be correct there is no way this is all it takes.

I just bought a used 2008 JD 3320 w/Cab, it has 1100 hours. I learned two things the hard way, when changing the hydraulic oil to always put a new o-ring on the oil filter cap. It is easier then dumping 7 gallons of brand new oil out and straining it to save $200. (And clean the fill plug )...

Our American Legion Post received a 2007 Cub cadet GT3200 with 102 actual running hours on it as a donation to sell for our MIA Memorial construction fund. The issue we are having is that the mower deck and 3-point hitch cylinders will not move up or down. The tractor drives in both directions...

My hydraulic flow control broke does anyone know of where you can find one or where or who has a parts tractor

Yanmar2310d hydraulic filter

i cant find what this part is in the mahindra catalog it just shows a square hole where this goes on the center case. my haudralics drained out of it. like a plug was released, not under pressure. it is on a 2015 gear series. thanks

Any one ever use Traveller hydraulic fluid for their Hst kioti ? Can’t find the Mobil orr a couple of the other brands in stock https://www.tractorsupply.com/tsc/product/traveller-premium-tractor-hydraulic-fluid-5-gal-t806391 thanks

trying to fix my case 2290's hydraulic leak ive identified the leak to the hose that runs from the hydraulic pump to the main controls in the cab, i cant for the life of me figure out how to remove the hose, it spins freely but doesnt unscrew, and its not a push pull release refrence pictures...

Hello all, I have an Agco ST41A, which is the same tractor as a Massey 1540, made in Japan by Iseki. The tractor developed hydraulic issues last fall and I'm trying to diagnose before spring. Symptoms were intermittent loss of Hydraulics and definitely whining and chattering noise from the...

Recently acquired my first tractor, a Satoh Stallion, with a hydraulic oil leak. Split the tractor, removed the clutch, and the clutch release bearing (throwout bearing) with carrier, and hit a brick wall. I assume I now have to remove the clutch release yoke and shaft so I can remove the...

Hello tractor gurus . Kind of a newbie didn’t grow up with this stuff . Bought my first tractor at about 60 years old.own a Kioti 26 and an old Ford 4500 industrial with 755 backhoe .Just pickedup last year for 2 grand .new injector pump starter.added Silverado seat an boat seat for back hoe...

I have been exploring an upgrade from my Deere 1025R. As I compare the hydrostat versions of the RK37 and TYM/Branson 3515, the primary thing that stands out is the hydraulic pump flow. According to their respective websites and TractorData.com: The RK37 is rated at 6.4 gpm; The 3515H is rated...

All, I noticed I my TC45DA is leaking/weeping hydraulic fluid. It looks like it’s leaking where the hydraulic pump bolts to the front cover of the engine and it’s not engine oil. Is there a chance that the hydraulic pump is just loos and that tightening the bolts will slow or stop the flow? I...

Hi all, I'm new here, in fact this is my very first post. I have an old Shibaura SD2843T (equivalent to a Ford 1700/1900) and it has a front loader that looks like its connected hydraulically in a very weird way. It seems it goes through the 3 point hitch hydraulic, what I mean is that the...

I just installed a dual rear remote on my XG3135. Not hydrostatic if it matters. I now have a tractor without any responsive FEL or three point lift. Pretty sure I did something wrong. The instructions were not clear on connecting to the loader valve, or they just assumed a level of...

This is a weird one; our x590 has never had a serious problem. But I had to take the mowing deck off tonight to reinstall the belt, which had come off one of the rollers. Something seemed strange, though; the deck wasn't going all the way down to the ground....wt...?. I did get the deck off with...

I have a 2006 JD 3530, Power Beyond, FEL, BH, Grapple. This morning I lifted the brush hog, set it where I wanted to leave it and removed it. Hooked up to the 3 point stump grinder that I've used a few times with this tractor, hopped on, moved the draft lever, it didn't lift the grinder. The...

I snagged a tree under my 2510 hst, and pulled off the rubber hose that I think feeds the valve under the passenger side foot. I have got the hose back on, but there is a larger metal hose that comes off what I assume is the hydraulic pump on the passenger side of the engine, and goes down...

Good morning all. I have owned a couple of BX models since 2001 and there have been maybe half dozen times I have had to top up the hydraulic fluid. Each time it was only a few ounces. Neither tractor had a front loader or bucket, just mower. A few years ago, my sister and niece got a L2501 with...

In 2020 bought a used NorTrac NT254 (Jinma 254) 25 HP 4x4 tractor with a power beyond loader valve. Converted the welded bucket to skid steer quick attach and got a set of forks. Wanted to add front remotes for a grapple. Studying the hydraulics and looking online, it took some doing to figure...

So I bought this small tractor to take care of our acreage homestead. I love it all from the reliable start-up and relatively easy maintenance but I don't know squat about hydraulic other than what I been reading up on. I was thinking about adding a double circuit bypass/diverter to the back so...

I have a diesel Massey Ferguson 135 and I bought it with the hydraulics backwards, I don’t know if it was replaced by an inexperienced mechanic or what the story is, but up is down, and down is up, figured someone had hoses or something switched, I’d like to make it right, it came with no...

I own a 1993/94 Ford Newholland 1215 compact tractor and after 870 hours I will be replacing the hydraulic fluid and filter. I am the second owner of this machine and I do see evidence that hydraulic fluid and filter have been changed previously. We no longer have a Ford/Newholland tractor...

working on installing rear remotes on a john deere 301 a, hoping to use a generic aftermarket set up to save on cost. main issue is knowing where to plumb into the tractors hydraulics to go to the valve body. any info on how to find which ports to use would be greatly appreciated thanks

My Kioti DK 6010 3-point hitch is not going up or down. Thought it might be low hydraulic fluid but I just filled it up and it still doesn't move. The valve under the seat is fully open so it's not that. I had just taken the backhoe off when I discovered that this wasn't working. Any ideas?

We were seeding and while turning around the tractor 'popped out of gear', anyway, it stopped moving forward. No broken linkages. Steering and loader no longer work either. Valves still work for loader will go down. It was running warm a few times because of plantmaterial on screen; removed it...

Hi all, had a sf310 sitting in shed for a couple of years, needed a new a new deck. Finally one came up at a good price. installed it, took it out, after 30 seconds, lost forward reverse in it. was wondering if issue could be air in the hydraulic lines? Or if anyone else has an idea. Hope it’s...

I have a Kubota MX5200. I have to questions. I bought a Titian 1912 rotary cutter. It has a single hydraulic hose for operation. I do not have rear remotes and just plan on mounting a single hydraulic control valve. There are some many options it has become confusing. What spool do I need and do...

Just out of warranty (of course), I found an oil puddle on the ground below my pull bar. The RK mechanic told me that even if it was under warranty, it wouldn't be covered because gaskets and sealant are considered wear items. So I had a local independent mechanic fix it. There's a plate above...

Does anyone know of a good site to cross reference website for hydraulic lift control valves? I'm looking to rebuild New Holland hydraulic lift/control valve part # MT40007577 (LS Part #40250285). I have been able to cross reference some parts on New Holland tractors but I haven't had any luck...

I am looking to get a hydraulic top and tilt setup for my Kubota L3301. I mainly want it for adjusting my rear scraper blade when maintaining my gravel driveway. Getting on-and-off-and-on-and-off to adjust the blade is hard on my back. Can anyone discuss the relative benefits of electric...

Hey fellow tractor users, I’m back with another DIY video this time installing a Summit hydraulics 3rd function kit to use a grapple on my Kubota L3301. The kit was really easy to install and works great. If anyone has questions let me know!

Need help with hydraulics not working. Is the pump bad or do I have other issues? The hydraulic pump is real noisy when I try to lift and takes a minute to start lifting 3 point hitch.

Annnd I am back... Ok got some strange things afoot with the 2440...When the PTO is disengaged, center lever down, I am having hydraulic issues. The Power steering will only work intermittently with High RPM's, and the rock shaft will do the same it may or may not go up with the higher RPMS...

I have a TYM T233, with the LT200 FEL. I’m getting ready to add a diverter valve to run a grapple. Max hydraulic pressure at the relief valve is 2500-psi. Does any one know what thread type/size the stock tees, and nipples are? I’d like to us hard lines as opposed to hoses as much as...

Hi all! I bought case ih 895 xl few weeks ago and I have a problem. Everytime when I stop engine, the tractor starts rolling like without engaged gear. The gearbox is equipped with hydraulic F/R shift. Hydraulic fluid is just between min and max and there is not a problem with driving whilst...

I'm getting a 3rd function kit and some attachments and was wondering what is the best coupler to go with? Seems like the flat face couples always come as an option for attachments for some extra $$$. Are they worth the extra money?

I'm getting a Kioto DK6010SE HSA. Total hydraulic flow is 16.49 gpm. The loader shows 9.62 gpm Rated Flow (Tractor System). Is the 9.62 what is available for the 3rd function valve or is there some other number I should be looking for it can calculate?

Ok. So I've seen a Kioti made 3rd function kit(DKA144) that looks super easy to install (video below) but I haven't found a dealer that sells it. Seems like most are installing the WR Long branded one. Is the WR Long any better? If so where is the best place to buy it?

Hi. I have issues with my hydraulics. The bucket dump is going down slowly and when I push the joystick all the way (it has a two stage valve: slow and fast), then the bucket rollbacks. It just started doing this. No other functions are affected. I had the cylinders resealed, did not fix the...

Hi guys, I bought a 2009 GC2410. The previous owner added a second hydraulic pump with its own oil tank on the mid-pto to operate the backhoe. I'm trying to put the tractor back to original as this setup is not working well. Can anyone tell me where are the 2 hydraulics from the backhoe...

Several years ago I bought a used BX22. Used rough but still in good shape. Had a little feedback when the peddle was depressed fully in high gear. After year one I change the hydraulic fluid and no change. Next fluid change I took out the screen and found a few large pieces of metal in it...

Have a 2003 DK55. Hydraulic warning light comes on after driving or operating cutter for a short time. Changed Hydraulic filter. Will check sensors next. Anyone experience this ? Ideas ? Thanks

Hey guys. I have a 3rd function kit installed on my Massey 1526. I want to add a rear remote to control the top link. Is it possible to just run lines to the rear and have ports like that? And then connect the top link into that? I’m assuming the diverter button on the joystick would then...

Hello everyone; Just bought a used TYM T264 and am thinking of installing a third function, as Tony's Tractor Adventure Homestead Shows in his video and getting a grapple for logs/brush/etc but I'm having trouble finding what the hoses/connections/fittings sizes are. Call the nearest dealer...

I had a few questions about the hydraulic chute rotator for the 2360 snowblower. I can’t seem to find a part # for the kit anywheres. I currently have the electric rotator but I am sick of the speed and how it freezes up every time I am out. Does anyone know if it is a simple bolt on kit? Or is...

I had to change the FEL hoses out on my 2400H and lost some hydraulic oil, Where do you fill the hyd oil at? I see where you put the engine oil at and there are two more places that has oil caps, one on the right front side and one behind the seat, what are these for? There is only one place to...

I'm new to large farm tractors, so please go easy on me. I bought a Ford 8600 back in August of this year. One of the rear remotes hydraulic line busted and gallons of fluid spewed out. I had to move it approx 50'-60' to get it out of the way from where the hose busted. I got sick and it...

i have a CAT skid steer model 232b2. i haven't been able to get the arms to raise up on it. with machine running parking indicator lamp does not come on. when i am pushing the button to release the parking brake, the seat belt indicator light starts flashing. machine will move, but i cannot...

Hello, I have a hydraulic leak and I think the culprit is the shaft which is used to open and close (what I believe is) the hydraulic lines. Something has caused the shaft to have an oblong rotation and it also seems like it has more wiggle than it should. I've included a couple pictures. I've...

OK, experts, here is the next in my series of questions from a beginner for beginners... My understanding of hydraulics is relatively basic. Essentially, a fluid contained in a closed system with a pump to pressurize it. Valves and the like are controlled by levers or switches to drive or...

I am new here and need some advice. Yes have a 2020 Kubota 2501HST and just got a Shaver HD8 post pounder. I need to install 1 rear hydraulic line to lift the hammer and 1 dump line. As I am new to tractors and hydraulics I could use Some suggestions as to what all is needed. My dealer quoted...

What brand of hydraulic oil do you use in the transmission of your DC 29D? Does anyone use Hy-Gard?

I am a newbie to TractorByNet. I grew up on a farm long time ago but enjoy the work I can get done around my little 11 acre piece of paradise here in Vermont with a tractor. I own a 2003 Kubota L3010 that I use occasionally for things I couldn't do otherwise so it doesn't get the hours of a...

I am looking for a land leveler to set / reset the camber on some dirt roads, and I came across a land leveler from Notch Manufacturing. These aren't gravel roads, so I am less interested in ripper teeth. Anyone here have any experience with it? It seems like a useful design to be able to...

Hey guys. Just wanted to share my channel with you. I work as a Turf Mechanic for many years and I'm still learning everyday but I may have some videos to help some people with certain issues on a variety of machines. I also work on Kubota / Case and New Hollands as well. Please subscribe to the...