hydraulic

Looking for tool suggestions to get these hydraulic hose fittings off. These are on a skidsteer snowblower. I had these hoses off two years ago because one hose had worn through over the years. Got them off and changed with a socket wrench. Had them off again last year because there was a...

I have an L47 TLB and was wondering if there is a simple cost effective way of using the backhoe hydraulic connections to add controls for three point functions like top & tilt when the backhoe is removed.

Will ask same on M-F forum, and did so on hydraulic forum... Need to pull engine and steering cylinder on my 1440V (rusting under chrome plate of ram) so grabbed a JIC 3/8 cap and plug. Duh....they don't quite fit! What standard are the hydraulic fittings made to? BPS???? and if so, why??

Will ask same on Iseki forum, and did so on hydraulic forum... Need to pull engine and steering cylinder on my 1440V (rusting under chrome plate of ram) so grabbed a JIC 3/8 cap and plug. Duh....they don't quite fit! What standard are the hydraulic fittings made to? BPS???? and if so, why??

I have a question for the collective and particularly for the experienced hydraulic members. I'm rebuilding the directional control on my Ford 1900 that was equipped with a spool/shuttle type directional valve for the FEL. Fairly straightforward to dis-assemble and clean but there are two yellow...

I have a chinese tractor 33.1kW(import name eurolepard 454) with Front loader. Steering is 100% Hydraulic. Had some power steer hose damage caused by poor routing (stressed the wire braid when front axle pivots) (M18x1.5 thread ORFS) Recently a right side fire from oil soaked wiring & a short...

My mid-mount mower is stuck all the way up. When I push the lever to raise the mower I can hear the motor and pump strain because the mower is already up to the max. When I pull on the lever to lower the mower nothing happens. Even in the float position nothing happens. The mower is stuck...

I have a 2008 JD 5303 4WD with JD 522 FEL. One known issue is 3PT lift will after a few minutes begin “hissing” when lift handle is raised to full lift height. Bumping lever down a little makes noise go away, but will begin “hissing” again after a few minutes. Periodically adjusting lever...

Hey all, realized hydraulic filter has never been changed. can't find replacement info, anyone get one recently? Need to replace 4wd oil seal also. Is it difficult? working my way through all the leaks LOL. Need to do FEL o-rings also and a bunch of hoses. Just got new tires. trying these...

I have a 2008 JD 5303 4WD with JD 522 FEL. One known issue is 3PT lift will after a few minutes begin “hissing” when lift handle is raised to full lift height. Bumping lever down a little makes noise go away, but will begin “hissing” again after a few minutes. Periodically adjusting lever...

What do you do next if gas was put in the hydraulic tank? Engine was not started at all. Dig-It M2208 bucket loader.

Good afternoon, I am having some difficulty understanding how to properly raise and lower the 3 point hitch, when I watch a video on youtube, The operation is as simple as moving the position lever. Both Hydraulic remote "A" and "B" appear to be in neutral and nothing is attached to the rear...

Yanmar YM2002D, I've been trying to troubleshoot a Hydraulic issue. The 3Pt and Bucket don’t work. I've replaced the Filter and Oil. I've cleaned the Screen, I've made sure the lines are clear. I can Pull oil from the screen filter to the oil filter. I can shoot oil out from the Exit port on...

I'm, taking off the top cover soon to rebuild at the least she will be getting new piston seals, top gasket set, hyd filter & a pressure safety release valve, while I'm in there I was thinking about removing the original hyd filter & placing it on the outside in which would be10x easier to...

Ok.. I’ve been looking all over for a side link and it appears that I’ve totally missed the bus. My fixed side link is 19 or 20 inches depending on which hole I use on the fork. As I understand the use of a side link, it would be best to have 4-5 inches of movement at least…. Some have said...

Hello. I just ordered replacement hydraulic hose 7J040-661110 for my LA402 loader. I was surprised to see that it is made with 1/4" hose. The old hose that I removed was 3/8". I called the vendor and they confirmed that, even though all the other hoses on that loader are 3/8", this particular...

Always had the squeal until fluid warmed up. At times, when fluid low from leak, the valve spool would squawk. I changed the fluid and filters out as maintenance, now, it squawks more frequently when hot or cold. tried running the hydraulics thinking it was air cavitation, but didn't help. Fluid...

John Deere 5320. I’ve been threatening to get a hydraulic top link for many years but never think about it unless I’m turning and turning the existing manual link. I want to know which links you all favor and which ones you think are junk, as I only want to do this once (well, twice since I have...

I have a 2007 Branson 3510i tractor with front and rear remotes on a BL10S loader. Had it for 14 years with no loader problems, recently found a hose with a leak and since I'm not near any place for service I decided to go ahead and replace 5 hoses that showed wear and potential for problems...

This is where I began. I have no hydraulics at the front except for the loader. I started shopping and found the Innovative tractor attachments for about $600 but it's only a diverter valve. So I started shopping for full 3rd function valves. The price is all over the place. Lane Shark is $2000...

Anyone ever experience a dealer/servicer recommend to not change the hydraulic oil in a shuttle shift? They said they only recommend changing if it looks milky because there isn't anything wrong with it. I've been debating on sending the oil off to be analyzed, but I don't know where to send...

TC35D replaced three hoses and a hydraulic cylinder. Checked fluids and refilled as needed. I started working machine and backhoe was digging but with reduced power for a bit. Friend started using backhoe and said he heard “a noise like something break”. I know- not very descriptive but best I...

Hi I am trying to increase the lifting capacity of my loader. People have been doing this with adding shims to their relief valve. I can't locate the Kubota shims at my dealer, Messicks, Golden Eagle Equipment or Kumar Brothers. Can anybody suggest a supplier or a work around? Shim part...

Well howdy. My Branson 2810 has a BL10 FEL. Has always worked well. I now have a rapidly dropping (leaking down) tilt on the FEL but cannot find any evidence of any external leaks. None from cylinders and none from any of the hydraulic lines. So, any suggestions on finding the leak? The...

I'm looking for a replacement for Mobil DTE10 Excel 46. Place here carries it but only 55 gal. drums. It's for PT30 Terex.

i bend my curl cylinders (running it without the kidney brackets) and now they started spraying oil, so they are dead. has anyone ever replaced the cylinders with some aftermarket ones? i really dont feel like paying around 1200$ for 2 OEM cylinders. thank you

Hello all, I'm hoping somebody can help me sort out this craziness I've been getting some pump whine lately, and was getting ready to figure it out, when I found out there might be a hydraulic screen before the filter. I checked he service manual and the hydraulic one line shows a screen before...

Prices too good to be true, free shipping etc. Anybody have any experience with these? I'd gladly buy a used, brand name unit, but i cant find any locally for even double the price of the Chineseium units, let alone delivered to my door.

I replaced hydraulic line going to cylinder on front end loader after finishing it will not move at all I don't know where bleeding valve is located on the tractor or the best way to go about getting air out

I have a Typhon Terror X and live in FL. Need to make sure the engine and hydraulics stay as cool as possible. Does anyone have any suggestions or pictures of what fan(s) and cooler to use? Best place to locate the equipment for max cooling? I saw another thread about installing a hydraulic...

I got my hydraulic multiplier mounted, and the wiring is done. Cylinders are arriving next week. Supposedly my kits for another rear hydraulic and 3rd function kit are supposed to ship Monday from LS. I've been told they are moving the parts warehouse, which is why there are long delays for...

I'm looking for a replacement for Mobil DTE10 Excel 46. Place here carries it but only 55 gal. drums. It's for PT30 Terex.

In researching hydraulic fluid levels for this tractor am I correct in that I check 2 different places. 1). The transmission level for transmission and 3 point at plug next to clutch pedal. 2). The hydraulic reservoir at the controls for the loader with dipstick. Thanks.

Was wondering if anyone has added hydraulic top link to a YM347, and if so, which kit? Looking over them for my new 347. Thanks!

I've been having issues with the hydraulic pickup screen plugging up (likely due to the brake lining). Until I can fix the brakes, I've been changing the fluid and cleaning pickup filter regularly. Espically when I noticed the hydraulics jerking. This last time I changed fluid and filters and...

I've got a couple of snow plows, (one is a Western, the other is a Kubota) Both are old and have been left out. The shafts are pitted. Since I have had the attachments, I have applied multipurpose grease to the shafts out of season. But that doesn't fix what has already been ... I have...

Hello all, I’m wondering if anyone has any recommendations of a hydraulic hose crimper to buy? Not something to use everyday but a few times a year forsure. I’ve seen some on Vevor and similar but they all look kind of janky. I’ve only ever had hoses made at princess auto, but they won’t put new...

Unloaded some firewood logs monday with the XR 3140 and when I parked the tractor I noticed the quick coupler for the bucket curl up function hose dripping, complete with an oil trail right to were I parked. So, I undid the quick coupler, could not see any crud or any o-rings wanting to leave...

I need to change my hydraulic oil which holds 8.2 gallons. Anyone have a favorite bucket or pan to catch the oil?

Seems pretty cut and dry, drain tranny, drain differential, change filters, refill. My plan is to warm up, make sure all hyd. cylinders are contracted. Am I missing anything? I still have a small leak, 5 gals over 500+ hours. I think it is where trans hooks up to motor. Will address when it...

My three-point lift stopped lifting. My FEL still works as it should. I took the top lid off to rebuild the cylinder and found this broke part. I assume it has something to do with the draft. 1. Does this broke part have anything to do with the three point not working? 2. Can I just remove...

Did a full service on my Boomer 33. What hydraulic fluid is best for this machine ? There are two hydraulic filters. A long large one mounted under the right side of the tractor in front of the rear wheel. I was given another smaller filter but cannot find where this one goes. The filter in...

Valby CH260 Hydraulic Feed Chipper Excellent Condition 6" Round 9 Slab Located in Woodstock Conn Can Load $3800

Right, I've fixed a double spool valve I had surplus behind the seat of my 1820, read up all about the need to insert a plug in the Yanmar hydraulic distributor & the need for a power-beyond sleeve in the spool valve, so I'm all set to plumb her up. What size hydraulic pipes do others use? My...

1979 satoh beaver s-373 with front loader. Front loader hydraulic pump broke and now needs replaced. How do you remove this pump first and what pump would work for a replacement? I have searched both everywhere and either don’t understand what I’m needing and I am missing something on removing...

Need help please I have a Massy 202 with a 101-102 loader .I lost my hydraulics and found this piece broken connecting my front pump to the loader hydraulics and can not locate one. Am I going to have to get it machined? It is a 3/4 inch bore and 1 1/2 " O.D.

Would anyone be able to tell me if there should be slop at the point my finger is at. The problem i am having is when my brakes 5release 4x4 i will get a loud clunking back there this is a caseih 75c thanks

has anyone used Bars hydraulic stop leak sealant? In which way? results? opinion?

Hydraulic filter cap blew off the bottom twice on me. Not sure what the issue is. Replace filter housing and now the steering only goes a 1/4 turn and then stays out hyd oil from the top of filter through thenoring. Any help would be greatly appreciated. Thanks

Just about ready to pull the trigger. It is a two part purchase, 1) adding two rear remotes to the 3038e 2) ordering a Frontier FL1061S (mfg by Maschio) 61" hydraulic offset flail via my local JD dealer. The attraction to this package is the ability to cut with the unit turned vertically 90...

Hello all, My 50 year old UTB Universal 445DT has inoperative rear hydraulics. For the past 45 years the rear lifter has only been used once or twice per year and now does not lift at all. I have determined that the hydraulic pump at the engine is working normally and there is plenty of fluid...

Hey, love the forum, first time poster, long time lurker. I recently picked up a 2006 GC2300, reading 395 hours (I don't think its 1395... the last hydraulic filter read 2017 and 195 hours). Its in pretty good shape, looks well enough cared for. I went through and changed all of the critical...

Hello, I was curious if anyone could help me find a repair manual or give me some instructions on how hard it is to fix a leak in my hydraulic system on my Kubota B7100 HST Diesel. The leak appears to be coming from the actual controls itself. I also noticed that there is a drip that looks like...

Pressure Control Valve blowing o ring on JD 310B what could cause this problem?

I was changing fluids (engine and transaxle) on my JD 445 mower and somehow grabbed the wrong oil container started pouring hydro fluid into the engine. I realized the mistake and stopped after about 3/4 qt and quickly started draining it. The engine was never started and I removed the new oil...

Hi folks -- Kubota ZD1211 zero turn mower use UDT2 hydraulic fluid. About 3 Gallons. Drain plug is on bottom of machine of course. Can't see how to drain 3 gallons out without lifting 1,700lb machine up (and level of course) to get a 5 gallon bucket under there.... so am thinking of pumping it...

I was drilling beans and had made a couple passes I started to make the next pass and when I dropped the drill the temp gauge went from normal immediately to hot so I quickly reached up to shut the tractor down it kept running a bit puffed black smoke and shut off. I got out and noticed fluid on...

Was moving some rocks today when all of a sudden I saw my loader cylinder dangling. Looks like a break at the weld. I am thinking this can just be repaired. Is that the case or do I need to buy a replacement?

Anyone have any experience with their MF 1635 Powershuttle hydraulic controller failing? thoughts. Mine has failed twice in 5 years.

Has anyone experianced their hydraulic module failing in there MF tractor. The PowerShutttle version. Mine has failed 2 in the last 5 years, seems like a real high failure rate. thanks

I need to replace all of my lines on the top & tilt spool (Gearmore). The tractor is New Holland compact TC24DA. Can anyone recommend a good source for the hydraulic lines? I’ve reached out to Gearmore but they have not responded.

My dad has a jd 2020 we used it for a few years but never used the pto last year after brushhogging we realized it was low on hydraulic fluid and smoking out the blowby tube so we parked it went to eat checked oil and it was obvious that the hydraulic was in the crankcase. We rebuild the...

hey all, I have a ford 1210 tractor. It is 16 hp, 15 hp at the pto. when i bought the tractor at auction, it came with a Ford 916A belly mower, however, none of the stuff to actually mount the mower deck to the tractor. A little background: over the years, i have welded up some things to mount...

I have a number of 1/4” & 3/8” hydraulic hoses to make and was wondering if anyone makes an affordable crimp machine that won’t break the bank. Reusable ends seem to be very limited to find. I had NAPA make two 27” long hoses for me the other day with 1/2” male npt on both ends at a cost of...

Hydraulic mower. I've rebuilt the motors that power the blades several years ago. Discovered I've got some dampness UNDER the deck....so something is leaking. Not a blow out leak but leaking none the less. (first start this spring, mower was VERY low on oil and I was baffled as to where it...

I just a acquired a beautiful excellent condition 1994 L255 New Holland that did not come with a manual. I didn't think to ask the previous owner, I thought it would be easy to find since I own a Bobcat 863. I see a dip stick in the cab on the left side floor but don't want to put something that...

Long time follower of this group, all y'all have taught me an awful lot even though I've not posted often. First time trying to use the auxiliary hook ups on my Montana 3840, and I'm looking for some help. Let's just say that the Korean-to-English translations in the owners manual for the...

2024 TYM T25 with about 15 hrs. I bought it new last October(ish). It came with the front grapple installed and I used it a bit last fall. Then the snow came and I went to the bucket which hadn't been installed until then. At some point I learned how to check the TDH fluid level through the site...

Posting this is a couple places. Made up a simple pressure gauge to check relief setting on my B21. A simple T fitting with 5000 psi gauge and a QC coupler on each end. It does work and show pressure, indicating about 1800 when the relief actuates. About what I expected and will, unless...

recently worked on a NH 75, farmer complained of loss of all hydraulics after turning it off hot after mowing hay. i've come up with a simple in the field bleeder port that takes less than a minute to do without taking any panels apart or lifting the hood! take out the large plug on top of the...

Do you have to use the UDT2 or can you use the UDT period!!

Changing the hydraulic filter and its super tight stuck. Is there a way to relieve any checked/holding ? pressure on this circuit if there is any? Is there a way to park it without the hydraulic system locking? Tried a spanner wrench and it stripped the only tooth I could get it onto. Going...

I have a Woods BH7500-1 on a Kubota L3600, the problem I am having is that the backhoe will not hold hydraulic pressure. If I raise the boom it quickly falls, if I put down my outriggers and raise the back of my tractor off the ground , the outriggers immediately lose pressure, I have removed...

I have a 2018 Workmaster 55 and have a dip stick in front bottom of the seat . Is that the hydraulic oil dip stick and do you fill it through there also . The tractor had no manuel and I had never had a tractor before. I had a line bust and lost oil I have replaced the line , but the loader...

Leaking hydraulic pressure sensor. Replaced x2 Now leaking again after only short usage.

I have a 1961 Ford 641 with no dip stick to check the hydraulic fluid. How do you check this fluid. Thank you

Good morning, and happy 4th to everyone! Skip this paragraph if you don't want the back story... I had recently won an auction for a 4 in 1 combo bucket that is rather vintage (melroe/bobcat brand with the internal/covered hoses reading '95). I knew it would need the cylinders either rebuilt...

Title says it all. Converting a Kubota B21 mounted WR Long 4n1 bucket to SSQA but there are no QC couplers, it is all "hard connected". Obviously time for QC and new hoses. I was going to just use the Kubota style AG couplers, but I've been told Flat Face is standard and should I rent any...

Good afternoon, everyone, well I ran into an issue and need some help diagnosing a hydro/steering issue. Two weeks ago, I was out removing some storm damage with my 3620H, I was using the grapple and was moving plied of branches from the road to a brush pile about 500 yards away. About the...

I have a freshly rebuilt and painted (by Brian with Fit Rite Hydraulics) top link with Euro quick connect that was made for and fits a Kubota M7060. I have the hoses and quick connects for rear remote and 3 each Cat 2 balls and 1each Cat 1 ball. Bought an MX6000 and this top link is not the...

I have a new to me 2008 MF1528 HST with 1520 FEL. I want to do a complete fluid change. However, there are no close dealers near my area. What would be the best hydraulic fluid for my machine? It will take about 8+ gallons of fluid. I do not know the history of the machine, so no idea what...

Hello all, My tractor is a 1968 Ford 2000 3cyl diesel. I've finished rebuilding the top lid and now my 3ptl is working as it did beforehand. New piston, honed cylinder o-rings, safety valve and relief valve. Oh and a very worn cam pin too. Even when I first picked up the tractor around 7...

I have a gray market Mini-ex ME-15 which I believe to be a Mitsubishi 1.5 ton machine. Perkins diesel. I recently replaced one of the hoses to the right pilot controls and now having issues with both sides pilot controls. Machine tracks back and forth no issues. Left Side pilot controls is...

I just did a fluid change (100 hrs.) and I had to add red dye to make the hydraulic fluid visible. I had overfilled it and had to syphon some out. Now I am a little confused - with loader and 3pt arms up I have nothing in the sight glass. With them down the sight glass shows full with just a...

I spent a lot of time trying to figure out the parts I would need to add to a cab tractor (limited to 4 valves due to cab interference; the non-cab may be able to go higher). You can also have some (2 or 3) valves under the cab (later versions of this model series I believe). Not sure the...

What is the correct hydraulic fluid for the kubota l185dt

I have a Kubota 2380 leaking all the hydraulic oil from a spot near the front axle, circled in red on my picture. I'm trying to find what this part is called and how I can repair it. I'm looking in the manual and on forums/youtube and cant find anything yet.

I wonder where to best measure hydraulic oil pressure and temperature on a 2.5t digger. General wisdom says oil temperature is most accurate at oil return. Where should I measure pressure? I reckon there are different places, but pressure would only show when the particular cylinder is operated...

Has anyone had any experience trying to get to the bearing on the hydraulic pulley out? We believe it is out. We are not sure how to go about getting to it what parts need to be taken off in order to get to it.

For the last couple weeks I have noticed my bucket coming up slower and with my forks attached to the bucket it tends to come down when the tractor is off. Recently even if the tractor is running it still wants to lower itself. It does not raise as high as it use to and it lift capacity is much...

I've got a 15' hydraulically powered flex-wing mower. 4-5 years ago, rebuilt all the motors that operate the blades (and the pump which hangs off the PTO on a speed increaser). Note that the outer two sets of blades are on the same hydraulic circuit. Fluid goes from the pump to the right side...

I've developed a hydraulic pinhole leak on 7/8 OD tubing on my Ford 4500 TLB. So far, I've been unable to loosen the flare fittings to pull the piece out. Do they make a repair clamp that would work in the situation?

Hello Folks, I have a TN55S with the standard 2 remote set up (adding 2 more soon). One remote has no float (I assume an 5161780) and the other is supposed to have a float mode (I also assume it is a 5180686). I am vaguely familiar with the float idea: an extra detent in the remote is supposed...

Got an EA rock rake a year or so ago. We are all aware of the calamity, so no need to go there. From the git-go, I found there was an issue with the top link mounting design. Otherwise no complaints. Well other that the "special orange paint job". Issue is the Kubota (Gannon) hydraulic top...

Hi Guys, My Satoh 650g has possibly the worse designed crank to pump coupler ever. It is 2 pieces of metal stock with a keyway and then 4 bolts to hold each half together. The crank adapter and pump both have a "double D" shaft. Problem with it is that the end that holds the pump shaft only...

I'm considering a project using a tractor to drive a hydraulic submersible water pump in a creek or pond. If anyone has experience or a pump to offer I'm interested. A pump to do this needs to output a minimum of 50/90 psi @ 200 gpm through a 3" camlock fitting. And pass 3/8 to 1/2 inch...

Hi there, I’m new to land ownership and equipment and would appreciate all pointer. I bought a Kubota L2501 last year, equipped with 3rd function hydraulic for grapple and an auger. While I really enjoy the grapple, the auger is way underpowered and even with 12 inch cannot dig a hole without...

I have a 2008 MF-1533 with Synchroshuttle transmission. If the tractor sits for a day or so the 3-point hitch and FEL do not work at all…power steering works fine. To get up and going I have to open the bleed screw on the rearward hydraulic pump and turn the steering wheel until the air gets...

Does anyone know if the stack valves that Case/New Holland uses for their mid-mount & rear remotes on the Farmall/JX/TN/Other series are the same flange pattern as the Prince Series 20 valves? They *look* to be the same; I'm not near the tractor at the moment to compare dimensions.

After months of waiting and a comedy of errors on the dealers part I finally have the YL310 front end loader and 3rd function kit installed. After fixing all of the hose routing issues (due to a terrible installation) I parked the tractor assuming it was ready to go. I came out a few days later...

bought an ih 584 and the pto lever was stuck on when purchased got it all freed up and it engages well and the plunger works up and down, but the pto will only spin at high rpm and can be stopped with a 2x4 with light pressure, put pressure gage on the line coming from the valve body where the...

I recently purchased a running 1963 MF-35 Perkins Diesel with multi-power. The seller had just done a hydraulic fluid flush. I asked him what fluid he used and he sent me this (Legacy ISO 68): He said that a previous owner has installed a new PTO Hydraulic Lift Pump, and that this is the...

I bought a 2012 Case IH Farmall 40B Shuttle Shift (being delivered tomorrow) it is the same tractor as the LS R4041 as I understand it. I went to the IH dealer to get the hydraulic fluid for it and they could not tell me how much I needed. They said it wouldn't be more than 10 gal. Well...

I tried to make it short and sweet. I can't stand informational video's that start out with the guy sipping his coffee, showing his dog and you have to get his life story before you get to what you want. This video is well under the 5 minute mark. Hope it helps show what you're in store for when...

CK3520se, and after putting on and taking off the brush hog, I’m going hydraulic top link. Is the tractor a CAT 1?

Hi everyone I just installed a new pump after mine failed. I had zero psi and I cleaned pressure relief. I replaced oil and seals on the metal lines. So I installed a new pump and it won’t prime or do anything I need some help. Do any of you guys have any pointer what I need to do. I followed...

While perusing the local junkyard (I do that all too often) I saw a scrapped digger derrick pole setting truck with a big hydraulic auger. Picture an International truck which puts in power poles. Every bit of it is available priced by the pound. I looked up the model number of the derrick...

Hi, I can't find the hydraulic filter on my TYM 474 2024.

I have a 2016 NH Workmaster 55 w/900 hrs and recently the Hi/Lo shifter started getting very stiff/hard to shift. It was low on HD fluid so I changed fluid/filter and it seems to be slowly getting a little easier, but nothing like normal. I have a couple of questions I hope someone can help...

Hello All, Please accept my thanks in advance. I'm working on a Ford 1220 and found a leak in the hydraulics. It's a "step-down" on what I believe is the return line from the power steering back into the hydraulic compartment under the seat. The tractor was gushing hydraulic fluid and when I...

Hello forum 2009 Mahindra 2816 3. Cylinder Mitsubishi diesel Hydraulic fluid pressure builds up after using the bucket. When this happens I release the pressure by pulling out the dipstick tube under the seat. I can hear and see the fluid pressure release like a volcano. Is there air getting...

Hoping someone might might have an idea why the side slide on my mower is locked up to one side. I thought this was a simple enough thing but I really don't know why it would lock in place like this. I even tried hitting it with the biggest hammer I have .. my tractor 😂 This morning I tried to...

Hi, Does anyone have guidance for removing this screen. I have removed the two bolts from the L Bracket as manual instructs but cannot figure out how to remove the bracket from the housing that houses the screen? Any guidance would be greatly appreciate. Thank you, Saxe

3/8" hose, 34" long. $96.17 each. I must have been under a rock. I thought: "OK so they're about $25 each but since inflation is only 3.5% since covid everything's doubled so they're probably $50. I should get a spare." ooops, the price was 4x that..... $100 each. ($212.37 for two little...

Need to change Mitsubishi MT 320 I just purchased. Is best 80/90 oil or what else. I know 80/90 is suggested.

Troubleshooting main/loader hydraulics on 2120. Pressure should be around 2500. Did pressure test with gauge and pressure shoots up to about 2000 for a second, and then settles down to 1200 after 2-3 seconds. What would cause this? Weak pump, or internal leak in one of the cylinders or in the...

Book is telling me to change both filters. The dealer also supposedly sent me everything I needed for the 50 hour service, and both hydraulic filters were in the box. But doesnt one of the filters require the system to be drained or the fluid will all pour out from the filter? The sent be a...

I have a hydraulic leak for many years. However it is getting worse. I looked it over for many times. I notice it after I use and park. I estimate it loses about 12- to 16 ounces, if you run it six hours. Being I only notice the bottom of the tractor with oil droplets, and no lines near by, it's...

Has anyone used the front end loader hydraulic connections to run the offset flail mower? I would need another 4 feet of line and a 180 degree redirect to do it. Support the lines in a way they do not get damaged is a concern too. I have 1 outlet on the rear of the tractor now. Offset flail...

I bought a 1981 Kodiak C70 dump truck. It had a plow and salt spreader. The hydro pump is engine belt driven with an electric solenoid to engage it (switch on the dash). I have removed everything for the front plow - 3 hydro lines ran to the front from the valve block, and the two cable control...

After looking all over the place to find what transmission hydraulic fluid should I should use in my Montana 4940C no information really was found. I realize it needs to be compatible for wet disk and wet PTO applications. My question is what oil would you use? I have a few options below.

I am getting ready to do the 400 hour service on my L3240 HST. The service includes changing the hydraulic filter, the transmission filter and the hydraulic fluid. The hydraulic fluid change requires 11.1 gals. There are three plugs that have to be removed to fully drain the fluid. See the...

I am trying to do a 200 hour service on my B2620 and I'm getting confused about the relationship of the transmission filter, the hydraulic filter, and the hydraulic fluid. The manual shows a 200 hour service interval for the transmission filter, with accompanying drain plugs. It also shows a 400...

The hoses on my brush cutter would like to connect to the machine at a 90 degree angle to the way the 1/2" flat face connectors are currently mounted: Do they make an elbow that has a flat face quick connect on each side that I could connect to the machine and then to the brush cutter hose? I...

I have a 2006 3015 HST and was wanting to know what transmission hydraulic fluid I should use in it. Also, I've seen 1 manual say 19 quarts and another say 24 quarts. How much does it take?

My backhoe is leaking from one of the curl function hose joins behind the boom cylinder where the hose connects to the hardpipe. The trouble is i cant even get my hand in there to peel off the cable wrap to confirm if the joiner needs tightening or its the hose. Anyone had experience getting to...

The pin on the backhoe bucket was frozen to the point it had ripped a weld free from a 1/2" steel bracket. Would not budge with lots of heat, PB blast, sledge and drift. So welded a 1 1/8" nut on the end and using the impact wrench back and forth many times it broke free. Dewalt and the Harbor...

I need to replace the hydraulic pump on my 2005 NH TC30. I can't find away to get to the bolts behind the pump. If you have don't it before, an help would be great, or maybe a link. Thanks

This crud (algae? mold?) Has been slowly building up and I've been putting off doing something about it. But coming back from several months away this Spring, its gotten significantly worse with more build up. Time to try and remove it. Any suggestions?

Massey 1260 I just got finished changing the hydraulic fluid and filter on the rear end. Cranked it up and it started then died and won't restart, like low oil pressure . No lights are on. That is if they work. Is there a special way to prime after a hydraulic change? There is a fill port...

It is a 304B by nortrac with T395E engine. I recently refilled my lift hydraulics and it seems to have leaked hydraulic fluid into the oil enough to blow the dipstick out under pressure with the engine running away and blowing oil and smoke. Hydraulic fluid was almost completely gone after...

Need help, own a John Deere 2020, power steering pump mounts on front of engine, replaced seal in pump but still getting hydraulic oil in crankcase, anyone have any idea what to look for next?

I want to put a hydraulic top-link on a MT357. I have one from a MT342 that I had but the top-link is too short. I have the Pat's Quick-hitch on the the 57 also. Anybody have one their MT357? What length did you get?

Ugh, I am struggling with my Yanmar 1510d . I bought this tractor 2 years ago (auction ? mistake). I just put a new hydraulic pump on it for the 3rd time. FEL and 3 pt hitch have stopped working again. I cleaned the filter and put in new trans/hyd fluid recently. I also installed a pressure...

I'm doing the 50-hour service on my MT240he, and am a little confused about what hydraulic filter I need. The manual states a hydraulic filter, but the website has both a hydraulic filter and an HST filter. Anyone know which filter to get? and what hydraulic fluid should I get to replace the...

My MT240 has a noticeable hydraulic squeal at startup. It only happens for a few seconds and when the tractor has been sitting for a few days. Is this a common issue? Should I be concerned or should I not worry about it. I have been on a friend's Kubota tractor that seemed to make the same noise...

Guys, Can you help. I am in the UK and have had a turfcat for many years and I recently broke the shaft on the deck hydraulic motor I have managed to get a new one but it will not run if it has any load on at all everything points to a blocked outlet pipe as when I turn it off it runs...

I can raise my bucket and tip in and out, but have no "power" to lift front tires off the ground. I replaced the pump (truth is I wanted one on the shelf anyways), no affect. Everything else looks good, no leaks, fluid/filter good. Kinda thunkin it may be an internal seal somewhere that...

Hello Everyone, I just want to say thank you for sharing knowledge here; these forums have helped me in the past when I came to lurk for answers. I purchased a tractor with 3pth snowblower and then purchased a loader to fit on it. Can I / or how can I, have control of both sets of circuts? (4...

If I want to run a hydraulic motor off my rear remote valve/coupler, do I need more than just the two lines? In other words, do I also need a tank return, so when turn the rear remote valve/coupler off it doesn't just slam to a stop? If I do how is it plumbed?

I have a hose on my loader that just started leaking, so I figure it's time to change out all the hoses. Are the cheaper (Ebay, China) hoses working for people? If not, what's a good resource for procuring pre-assembled hoses?

I am taking the next step in my tractor evolution. I have bought some hydraulic implements (root grapple, cutter, custom fork grapple). Since most of what I will be doing is open/close (grapples) power on/off (cutter) I am thinking of using my rear remote rather than spend $1000+ for a third...

I've made the repairs to the engine interface plate hardware and crank shaft bearing cover, with new seals and hardware. view"ck20 clutch post" Now I'm investigating the snap ring on the drain plug issue. I've removed the 3 pt hitch hydraulic assembly and nothing appears to be out of place. Once...

Well today I blew my first hydraulic line. Happens to be one of the four that operate the bucket. So I decided not to waste time and instead have lunch and reach out to you guys. I briefly followed the lines and they go up into the dark area about where the seat is. Fluid was still dripping...

Had to replace a 4 foot hydraulic hose the other day.....$ 84 for one hose....outrageous !!!

Need both pumps or rebuild kits. Does anyone know if these exist or if there is anything I can bolt on to replace them? Thank you in advance

Is anyone parting out an L5450DT/L4350DT /L4850DT? I urgently need an hydraulic oil cooler for my tractor. Alternatively: which oil cooler can I adapt for my L5450? I just cannot afford around $1000 for a new one. I already had the old one repaired, but that repair only lasted for about 2 hrs....

I pass along so it might help someone, seems kind of unusual. I bought my Mahindra 5010 used. After using it awhile, I started noticing some kind of fluid on the ground after I moved the tractor from where it was parked in the pasture the night before. But it seemed to be under the wheels, not...

does the transmission hydraulic fluid operate the rear hydraulic lift on a 2200D Yanmar tractor?

Just wondering what type of o ring the hydraulic hoses take for sealing on my LW8? The description is o ring but is that true or are they some type of flat rubberized seal? Any idea of the sizes used on the backhoe and I guess the loader as well. I’m just replacing the lines outer spiral wrap as...

I recent purchased this tractor that had been in a field for years. went through and changed all fluids, filters, screen and cleaned out the insides. The front loader is slow and shakes lifting, going down is fine. Same happens when I curl up. Curl down is fine. Plenty of fluid and all new quick...

Hello, I have Question pertaining to the YM276D I am wanting to install some hydraulic quick couplers to attach a 2 point backhoe, I know there are potentially 2 options one being cutting the high pressure line and second using the in and out ports (preferred if possible) I am just not...

Started baling today and the hydraulic tensioner will not get tight (bales loose) then it started shooting oil out the gauge. Help!! I can't find the book and my dad passed away in December so I can't ask him.

What kind of hydraulic fluid will work in my mahindra 6500 besides mahindra brand

Recently I had issues with my hydraulic pump so I pulled it and got a rebuild kit,(some seals and orings ),but when I put them in the seals are thicker than ones that were in it when you tighten the two bolts adasnt from each other you can't turn the shaft with a wrench, any idea's?

Hey guys, running my Mahindra 2538 HST pretty hard today and all of a sudden I heard a small pop and noticed hydraulic oil pouring out. I was able to drive it back to the garage after adding some fluid, but still leaks pretty bad. It appears that the leak is coming from the flare on the pipe...

Hi, New to posting but have been trying to read a lot of the posts. I am in the process of adding a used 3pt backhoe to my tractor. To get hydraulics to the rear I am basically splitting the hose coming off my power beyond port on my loader and will send the fluid back to the backhoe and then...

I have a Mahindra 2615 and it continuously got harder and harder to lift the 3-pt hitch. I took it apart and greased all linkages. Now this part on driver left pulls out about 1.25 inches. When pushed back in it does not seem to engage. Moving the control lever on the right side has no...

I'm looking for another tractor to be a dedicated tedding or raking tractor. I need at least one remote but it has to have a 4 position valve with float mode. Back in the day I had a 3930 with dual pumps and dual remotes that had this feature. I am finding out that I should have kept that...

This was certainly worth the research effort… Besides the hydraulics, I wanted something that would compensate for the Pat’s quick hitch extension, and add a quick-attach to the top. Also, found I can use the inexpensive, locally available, top-link balls by doing a little grinding…

I have a 1990 New Holland 7308 frontloader on a TC33D that needs new hydraulic hoses for the bucket. I am thinking of replacing all of them since they are all cracking. My question is where is a good reliable place online to purchase them? Should I replace all of them at the same time or just...

I have two kioti hydraulic oil filters T4125-38021 , unopened and still in bags ... The dealer sold me these and they were incorrect for my model kioti tractor, I didn't know until maintenance time. The dealer is 1100 miles away and hasn't responded to my request for exchanges

Ive been reading here and on the internet that some owners turn up their hydraulic pressure on their 2520s been thinking about doing that any of you owners had done this? I check mine and its 2475psi thinking about going to 2700 will I break something or blow seals out with 200 more psi thanks

Hello all, Anyone with any exp with Iseki tractor ? I have a slow leak in a few spots, anyway need to top up hydraulic fluid. Seems there is a dipstick in centre console area behind shifter and a bolt type plug nearby, however the tube you can fit in there is a bout a quarter inch ...

I've got a Ford 5030 shuttle shift that is having an issue with the hydraulics I can't seem to figure out. The transmission shifts great, and the power steering works tolerably. The loader and 3-point hydraulic are very slow and jerky. The loader runs off the rear remotes supplied by the engine...

Hi all, I have a 2007 3820i with a BL20A FEL. Does anyone know the recommended hydraulic pressure setting. I think mine is off and new to adjust. Thanks

What filter are you us for the smaller hydraulic filter on the left side of the engine (looking from seat)that is readily available? Also, is this a low pressure filter? NH part number is SBA340501030 (says it has a bypass valve), I couldn’t a cross reference on Baldwin Filters site that is...

My 1445 has 1725 hrs and the deck will not stay float . It has a danfoss hydraulic control valve . I am not sure if or how to adjust the detent to keep the deck in float

Hello this question has been asked a million different times but a lot of them are conflicting - what is the latest advice on what fluids to use? In particular, my tractor has two pumps, one for the steering and one for the loader etc. Should I use an ISO 46 in the steering and a UTTF in the...

So, I’m gearing up for the first service this year on the 4820H. It may be a smidge early in hours, but 2 years in I feel like doing it. So, I have Rotella T6 for the motor, but I came across Triax Agra UTTO XL fluid for the transmission. Also considered the Shell Rotella HD oil. Does it...

The loader jerks really Bad when the oil is hot . I have replaced the pump, loader control valve, relief valve, change filter and oil ,replaced all suction hoses on suction side of pump ,changed the quick couplings and switched the hoses on the lift and replaced the cylinder packing . Installed...

Seems I need to replace a hose on my GC1705's FEL (DL100)... part SL103366. The tractor/FEL is around 10 years old, and is stored outside. Should I be looking to replace all the hoses at this age, or should they generally run longer? Is there a standard replacement interval? Is there much of...

Hello all. Well i was very excited to get my first tractor this weekend(I have only had skidsteers in the past.) Saw a great deal on a RK37 shuttle shift with 240 hours and I jumped on it. Guy said it had no leaks and I didn't notice anything while i was checking it out, but it was in the...

I have a Long 560 tractor with a hydraulic leak from the transmission case. The drain plug and two holes in line with the axles and drain plug are on the bottom side of the case. One hole is plugged with a bolt and jam nut. The other hole is wide open and the parts manual does not show anything...

A friend had a hydraulic leak on his 2350 and after removing the hood we discovered split/rotted small hoses running from what I assume is some sort of surge tank just behind the radiator. The tank is about 8" diameter or so and has a T fitting on top with barbed nipples where the two lines...

Removed the front end loader from 1025r. Re-installed 2 hours later. Now, when I try to tilt the bucket down, it comes up. Hoses are connected properly.

Does anyone know how much hydraulic fluid a 2610H holds? The manual doesn't say and when google it I see anywhere from 2.9 to 12 gallons. Here what in the manual and it can not be correct there is no way this is all it takes.

I just bought a used 2008 JD 3320 w/Cab, it has 1100 hours. I learned two things the hard way, when changing the hydraulic oil to always put a new o-ring on the oil filter cap. It is easier then dumping 7 gallons of brand new oil out and straining it to save $200. (And clean the fill plug )...

Our American Legion Post received a 2007 Cub cadet GT3200 with 102 actual running hours on it as a donation to sell for our MIA Memorial construction fund. The issue we are having is that the mower deck and 3-point hitch cylinders will not move up or down. The tractor drives in both directions...

My hydraulic flow control broke does anyone know of where you can find one or where or who has a parts tractor

Yanmar2310d hydraulic filter

i cant find what this part is in the mahindra catalog it just shows a square hole where this goes on the center case. my haudralics drained out of it. like a plug was released, not under pressure. it is on a 2015 gear series. thanks

Any one ever use Traveller hydraulic fluid for their Hst kioti ? Can’t find the Mobil orr a couple of the other brands in stock https://www.tractorsupply.com/tsc/product/traveller-premium-tractor-hydraulic-fluid-5-gal-t806391 thanks

trying to fix my case 2290's hydraulic leak ive identified the leak to the hose that runs from the hydraulic pump to the main controls in the cab, i cant for the life of me figure out how to remove the hose, it spins freely but doesnt unscrew, and its not a push pull release refrence pictures...

Hello all, I have an Agco ST41A, which is the same tractor as a Massey 1540, made in Japan by Iseki. The tractor developed hydraulic issues last fall and I'm trying to diagnose before spring. Symptoms were intermittent loss of Hydraulics and definitely whining and chattering noise from the...

Recently acquired my first tractor, a Satoh Stallion, with a hydraulic oil leak. Split the tractor, removed the clutch, and the clutch release bearing (throwout bearing) with carrier, and hit a brick wall. I assume I now have to remove the clutch release yoke and shaft so I can remove the...

Hello tractor gurus . Kind of a newbie didn’t grow up with this stuff . Bought my first tractor at about 60 years old.own a Kioti 26 and an old Ford 4500 industrial with 755 backhoe .Just pickedup last year for 2 grand .new injector pump starter.added Silverado seat an boat seat for back hoe...

I have been exploring an upgrade from my Deere 1025R. As I compare the hydrostat versions of the RK37 and TYM/Branson 3515, the primary thing that stands out is the hydraulic pump flow. According to their respective websites and TractorData.com: The RK37 is rated at 6.4 gpm; The 3515H is rated...

All, I noticed I my TC45DA is leaking/weeping hydraulic fluid. It looks like it’s leaking where the hydraulic pump bolts to the front cover of the engine and it’s not engine oil. Is there a chance that the hydraulic pump is just loos and that tightening the bolts will slow or stop the flow? I...

Hi all, I'm new here, in fact this is my very first post. I have an old Shibaura SD2843T (equivalent to a Ford 1700/1900) and it has a front loader that looks like its connected hydraulically in a very weird way. It seems it goes through the 3 point hitch hydraulic, what I mean is that the...

I just installed a dual rear remote on my XG3135. Not hydrostatic if it matters. I now have a tractor without any responsive FEL or three point lift. Pretty sure I did something wrong. The instructions were not clear on connecting to the loader valve, or they just assumed a level of...

This is a weird one; our x590 has never had a serious problem. But I had to take the mowing deck off tonight to reinstall the belt, which had come off one of the rollers. Something seemed strange, though; the deck wasn't going all the way down to the ground....wt...?. I did get the deck off with...

I have a 2006 JD 3530, Power Beyond, FEL, BH, Grapple. This morning I lifted the brush hog, set it where I wanted to leave it and removed it. Hooked up to the 3 point stump grinder that I've used a few times with this tractor, hopped on, moved the draft lever, it didn't lift the grinder. The...

I snagged a tree under my 2510 hst, and pulled off the rubber hose that I think feeds the valve under the passenger side foot. I have got the hose back on, but there is a larger metal hose that comes off what I assume is the hydraulic pump on the passenger side of the engine, and goes down...

Good morning all. I have owned a couple of BX models since 2001 and there have been maybe half dozen times I have had to top up the hydraulic fluid. Each time it was only a few ounces. Neither tractor had a front loader or bucket, just mower. A few years ago, my sister and niece got a L2501 with...

In 2020 bought a used NorTrac NT254 (Jinma 254) 25 HP 4x4 tractor with a power beyond loader valve. Converted the welded bucket to skid steer quick attach and got a set of forks. Wanted to add front remotes for a grapple. Studying the hydraulics and looking online, it took some doing to figure...

So I bought this small tractor to take care of our acreage homestead. I love it all from the reliable start-up and relatively easy maintenance but I don't know squat about hydraulic other than what I been reading up on. I was thinking about adding a double circuit bypass/diverter to the back so...

I have a diesel Massey Ferguson 135 and I bought it with the hydraulics backwards, I don’t know if it was replaced by an inexperienced mechanic or what the story is, but up is down, and down is up, figured someone had hoses or something switched, I’d like to make it right, it came with no...

I own a 1993/94 Ford Newholland 1215 compact tractor and after 870 hours I will be replacing the hydraulic fluid and filter. I am the second owner of this machine and I do see evidence that hydraulic fluid and filter have been changed previously. We no longer have a Ford/Newholland tractor...

working on installing rear remotes on a john deere 301 a, hoping to use a generic aftermarket set up to save on cost. main issue is knowing where to plumb into the tractors hydraulics to go to the valve body. any info on how to find which ports to use would be greatly appreciated thanks