Pulled the head, have a large crack and a decently large hole inside the intake side of the head. Is this something a machine shop can mess with? Hard to find a new head for a 1968

Hello all, My tractor is a 1968 Ford 2000 3cyl diesel. I've finished rebuilding the top lid and now my 3ptl is working as it did beforehand. New piston, honed cylinder o-rings, safety valve and...

I have a 1974 ford 2000 tractor and I’m looking for loaders that will fit. I saw that the Ford 771 and 772 fit. But, I was wonder if and other brands or series will fit?

Long time reader / first time poster...! I am in the process of rebuilding my Ford 2000 top lid and I believed I had ordered correct parts. So far everything has been a 1 for 1 likeness..Until...

Hi all, I'm trying to replace the starter on 1964 ford 2000 4 cylinder 12V tractor. I'll attach a couple picture but the new one i got seems to not fit fit exactly right, there's a gap between the...

I'm changing the fuel line from the sediment bowl to the carburetor to a steel line with flared fittings. Just don't run the new fitting into the carb too far or it will break out the threaded...

Good evening all, I am not sure I am in the right forum, but here goes. Several years ago, I purchased a Ford 2000 Tractor, with a Bush Hog and a Ford 711 one arm loader, non manuel dump. While...

Hey friends, I purchased a 1967 ford 2000. Unfortunately I had it 2 hours when the motor seized. Im looking to see if anyone has a used one or any advice for getting mine rebuilt. Ty

Had to remove a lot of paint. Found the Ser.#'s I believe. L. side Trans Housing. By the Starter 1201 ? Then below it 31038? On the Eng. block L.side CONN 60150. Clutch is stuck and with a FEL...

Is anyone able to share photos or drawings of the correct path for fuel lines? I have acquired a 1974 Ford 2000 with a gasoline 3 cylinder engine. Someone has cut the original fuel lines and...

looking for the rear axle oil level plug. found the transmission level plug and the hydraulic dipstick. i thought the rear level was going to be the plug on the back but I think the manual is...

Bought a Ford 2000. Has a bit of blow by so I’m easing into this project as I am not sure what the engine condition is. It runs well, drives well; but the 3 point lift only raises 8 inches at...

Hello, I just picked up a ford 2000 3 cyl at auction. This tractor will not go into gear. I have not pulled the transmission top cover yet to look at the shift forks. I spoke to the previous...

I was bushhoging with my grandpas 1973 ford 2000 diesel last summer and the back tires went down in a little ditch and the bushhog stayed up on the hill so I was stuck until I raised bushhog. Well...

Wanting to add a 730 loader to my Ford 2000. Looking at the center axle pivot pin, I have a solid pin. I am guessing I would need to update the pivot pin to a hollow pin to accept the splined...

Any idea what it would be worth? Runs good, converted to 12v, and has power steering. Do these have live pto? Primary use would be brush hogging ATV trails, tilling food plots, etc.

My 3-point lift lifts OK and will hold anything i lift up as long as the lever is all the way up, even when shut off. The problem that I have is that only the last couple of inches of the lever...

I recently replaced the PTO shaft seal on my Ford 2000 3cyl.gas tractor. The 3 Pt.was working fine before I replaced the seal.After replacing the seal and refilling the rear end with Hyd.fluid ...

Hi All, THis is my first time posting here and I am looking for some help in where to start. I bought a used Foord 200 Dextra diesel for a good price. It starts good, runs well and pulls and...

Hey guys, I ran into an odd issue. I am needing to replace the head gasket on my 1964 Ford 2000. When I go to order the gasket I find there are two bolt sizes, 1/2" and 7/16". This is my first...

My power steering leaks on the 2 steering arms shafts on both sides. Is it difficult to replace these seals ? Would the power steering work even though they leak ?

I parked my Ford 2000, 3 cyl gas, for about a year and a half and it is now seized. I poured ATF in after removing spark plugs last night to let it soak and was going to try to break her free this...

Hey everyone, just got a heck of a deal on a really nice and well maintained Ford 2000 4 cylinder in great shape. I live in Northeast Ohio and my fiancé and I just got our first farm. I'm looking...

Y'all, Last year, I replaced a failed hydraulic pump on my 1963 Ford 2000 with a rebuilt unit from a reputable supplier. Additionally, I went through the top cover with a new piston o-ring, new...

i have a 1972 Ford 2000 3 Cylindar gas tractor. I have a Ford 2000-5000 Operators Manual. I have a pdf of a 1965-1975 Ford Tractor Service Manual that includes models 2000, 3000, etc; its more...

1972 Ford 2000 Its time for a new seat. I have have had a universal seat on my tractor for ~ 15 yrs but remember the OE seat felt better. I ordered an Ai replacement pan seat with suspension...

Yall, I need some help. The hydraulics on my tractor are not working. Theyve always been a bit sketchy, only lifting the implement in the last little bit of lever travel, but now they arent doing...

Bought a 2000 model ford tractor and it has taller tires. My fenders are off but when I checked the mounting the fenders touch the tires. I see some fenders have a taller mounting bracket. Can I...

I have searched this question in a dozen different search engines with no real help at all. Hopefully, some of you guys will know. Considering the 1962-1965 Ford 2000, what does one look for to...

Hello all. I have a check valve leak on the lift cover assembly of my 1966 Ford 2000 3-CYL Gas Engine. I found out recently that the transmission fluid level was extremely high. I don't know if it...

Just a question concerning 3pt on this tractor. When I engage the 3pt it either goes all the way up or all the way down. Am I supposed to be able to stop it going down at different levels? Is the...

I am rebuilding my Zenith carb. The kit came with the attached part.....I removed the original but am having a dickens of a time reinserting the new one. What is it's function?

Hey guys, I'm having trouble. I drive out in a field to do some work no problem. Went to start it up to head back to the barn and it wouldn't fire. Starter cranked and the motor turned over, but...

Im new Hello everyone lookin and cant find valve lash(clearence) specs for 1971 ford 2000 diesel have I&T repair manual orderd wont be here till after christmas

I was hoping someone could weigh in on some issues I have with my tractor. I've rewired the tractor from the headlights back to the instrument cluster. Everything is right(i'm assuming, the...

I saw an old Ford tractor in the back of a shop a couple of weeks ago when I was buying a welder that had been advertised. I told the lady I was interested if she would sell it. And got the I’ll...

I noticed that the battery wasn't charging (no voltage increase when running), checked the generator (Lucas) output (probably incorrectly), seemed very low. took it to shop, the man said it's...

Hey guys, I have a 1964 Ford 2000 gas/4cyl. Two years ago I had a bad water pump, I replaced it and the thermostat. It started overheating again so I pulled the thermostat and boiled it. It...

I'm helping my son with his 2000. The clutch is shot but it also has oil on it and in the bottom of the bell housing. Its not a lot of oil but it is getting on the clutch and any oil on the clutch...

Trying to help my son with his 2000. I think its a 74 It is a 3 cyl with a holly carb. At low speed it runs fine. When you put it under load, or even go from idle to full, it takes a few seconds...

Hello, I have a Ford 2000 diesel and would like to know it's year model. Info. I found is Tractor number C262679. Model B1012C. Engine 9M17B. Trans. 9L10B Any info. would be greatly...

What is the going price for these tractors in good condition with maybe 1500 hours on them? Most I find are the 3 cylinder gas motors? Are these reliable?

A Ford 2000 came into my shop last week and I was surprised to see that it has a factory Torque Converter transmission. My NH dealer didn't believe either and I had to send a pic to prove it ...

Hi Y'all, I have a 1963 Ford 2000 gasser, converted to 12V w/electronic ignition. It's been running pretty good, but a day or so ago, I went out to start it, and nothing...an occasional click...

Hello, Recently I bought a fairly worn-out 1963 Ford 2000, but there appears to be an extra hydraulic lever which does not match with what I have seen online or in the manual. The previous owner...

Need info on power steering leaking.

I have several things going on with this 2000 that I bought this year, but I want to address some wiring questions to begin with (for now!). I will try to keep this as short as possible. The...

hi, I have a 1967 ford 2000 gas tractor that is in need of a tune up, points, condenser and rotor. I have read that tisco should be avoided. Went to NAPA website and search under 1967 ford 3000...

New member here with a couple of questions about a Ford 2000 we just bought. model number is 20303 S, I know what the numbers mean but what does the S at the end mean? The serial number is 148851...

I just aquired a f 2000, all of the 4 forward gears work as they should except reverse. Is this a common problem????.

I put a new (off of ebay) steering sector on my tractor because the old one was worn out and leaked. I am a little disappointed the steering isn't easier with the new unit. The new unit took out...

Hi all, I'm a first time tractor owner and I bought a 1963 Ford 2000 gas tractor for our new property. Before I hooked up any implements, it ran great. As soon as I hooked up the bush hog, it cut...

What is the parts availability scene for a 64 Ford 2000, Gas model? One for sale in my area, has me thinking.

Hi all, My tractor started to pour fluid out of the pto . I pulled the shaft out of center housing and I can pull the shaft out of bearing by hand without removing anything. Is this normal or is...

I have a 1973 Ford 2000 3cylinder gas burner. I had to replace the gas tank, and found that the wiring harness was very brittle. I believe a wire (or two) broke, and now it won't start, or...

I want to rent a seed drill. It requires hydraulics to raise and lower each side of the implement (2 hoses). The tractor is a 1971 Ford 2000 diesel. What's the cheap way to set up remote...

I have a ford 2000 3 cyl diesel 1972 and it caught on fire ( electrical short) It melted all the fuel hoses from the fuel filter. I have searched ford parts list and all the lines says not...

1971 Ford 2000 diesel. Two questions: 1) I have about a 4" toe out. Was that way when I bought the tractor. I tried adjusting the drag links shorter but could only get so far. I'm wondering if I...

Hello all, Long time reader here. I've owned my first and only tractor for around 12 months now on my farm. I've got an old Ford 2000 (not sure what year) with a FEL. Its only used for a bit...

Good Morning Everyone! I posted about a month ago on this issue. Since then i have replaced carb and replaced spring but it is still idling up and down sporadicly but never dies. I pulled the carb...

Have a 1968 Ford 2000 3 cylinder has a problem after sitting all night long doesn't want to start. Replaced distributor, points, condenser, plugs, wires, cap, roter and coil. Rebuilt carberator...

Edit---As often happens, I'm able to find the answer if I keep looking. Now that I understand the loader connections better, it appears that this loader has two basic designs -- one for the 4 cyl...

Hello all, As the snow is starting to fly here in Nova Scotia, Canada, I read that its supposed to be a hard winter with plenty of storms. I cannot find any info on the internet re: a block...

Hello, I inherited a Ford 2000 diesel. Year model is between 1970-1972. Need to change hydraulic fluid. What type should I replace old fluid with. Thanks

I have a 1964 Ford 2000 tractor. When I was overhauling the motor I broke the 6" shifter cable that goes inside the transmission. I am not having any luck finding one at the local salvage yards or...

1965 Ford 3 cyl gasser. Problem began a few weeks ago. Runs well with load on drawbar (soil conditioner), but with any load on the PTO (hay rake, hay tedder, bush hog (60 inch), I lose power and...

Hi all, I have a 1972 ford 2000 3cyl gasser that has just started giving me issues with the fuel system. First off, it wont start without starting fluid, and once it is going it runs like a 2...

The Lift Control handle of the 2000 got very stiff to operate. The Hydraulics worked fine but it was very hard to raise or lower the control handle. I thought that maybe the friction disc being...

Hello, I recently purchased a 1967 ford 2000 with a FEL. Tractor runs well and everything works as it should, only issue I have is the narrow tri-rib fronts. They are tearing up my lawn as well...

Hello, I recently purchased a 1967 ford 2000 with a FEL. Tractor runs well and everything works as it should, only issue I have is the narrow tri-rib fronts. They are tearing up my lawn as well...

Ok fellas I have a ford 2000 great tractor but have a issue with the lift ... It will lift a heavy round bale but here are my symptoms .. 1. It only lifts the last 1/4" of the movement of the...

i have a 1965 ford 3cyl diesel ,6speed i have swapped top cover as the orig was wore , also noticed the square (pawls) that the shift shaft goes into is not perfect its wore . i hear that i can...

I have a 1963 Ford 2000 4-cyl. gas. it has been converted to 12 volt, one wire alternator. New battery, starters good, relay's good. I can't get power through the relay to the starter. I've even...

As the title says, I've got a Ford 2000 and have been struggling to get a good plow to run right, and I now think the reasoning is to something wrong with my lift system. With the tractor off and...

Anyone have any tips on how (if at all) to get the bushing out of the top link rocker? Mine need to be replaced. I tried hitting it and soaking it some, have Kroil on order. Don't want to bust...

Hello, first time here at the forum. I'm looking into getting my first tractor. this site has helped a lot on research. I've located what is listed as a late model ford 2000. I was wondering if...

I've had this tractor for a little while now, and I got around to checking the steering, and there was no fluid in the box. So I filled it up with 80w-90. In 2 days there was almost no fluid in...

I'm new to the tractor world and really looking for some help. When I first received the tractor it'd only run with the choke all the way open. I pulled the carb and cleaned it up, sealed it with...

Looking for a part number for a starter for above tractor. Anyone able to help?

I need some help here. I mounted a 703 loader on my Ford 2000. But I need some advice on the hydraulic connections.....on the module to raise and lower the bucket which port is the power port and...

I know I'm gonna sound stupid but here goes My 1972 Ford 2000 diesel 3 cyl has not had any lights or gauges hooked up sense I got it so I bought a new wiring harness and oil pressure switch wire...

My first time on the forum. My son was given a Ford tractor, he was told it was a 1965 model 2000. Now we are trying to confirm for sure. He has a John Deere, but he's always wanted to try and...

HI folks, [I] have a 1972 ford 2000 3 cyl. diesel . The starter drive keeps spinning after tractor starts. Turn key off and still spins, kill tractor and still spins. The only way I got it to stop...

i have inherited (lucky ) a 196x ford 2000 the numbers never made sense with the charts . its a 3 cyl diesel 6spd with non live pto. i have a pretty good leak at the crossshaft seal on both...

Help! I have just purchased a Ford 2000 tractor. The serial number is 1004B so i think it is a 1962. It is a three cylinder. I have lots of light uses for a front end loader and am looking...

1974 Ford 2000 8 speed power steering Just bought the tractor. Changed all the fluids today and I'm down to working on the brakes. Tractor runs good. Brakes work but pedals won't return to up...

I have a ford 2000 diesel last year I put all new injectors in it,I got it started with no problem it ran great for about an hour I was using my bush hog it started running ruff and began to...

I have just bought a 1966 Ford 2000 diesel, the 3pt hitch is very slow to raise, if I increase the rpm's it will raise, it does not leak down once the implement is raised. I removed the hydraulic...

Hi I have a 1965 2000 3 cylinder gas. It starts up a little rough, but settles down and runs pretty smooth. However, when I put much load on it, like when I put it in 3rd or 4th gear and start...

'72 Ford 2000 manual steering sector. I am installing a complete new aftermarket manual steering unit on my tractor. My shop manual says SAE 90 Ford numbers ESW-M2C 28-BA or ESEN-M2C94A...

Hey guys, I have a 1972 ford 2000 and I bought a new generator with tach drive. Hooked up and tach meter don't work. I replace the instrument cluster and cable and It still doesn't work. I took...

hi I am dave and I just joined this sight I have a 1966 ford 2000 and am rebuilding lift cover on the piston the shop manual says put on leather ring and o ring howerver the rebuilt kit has a...

I need both left & right side front axle knees and spindles. Maybe even the hubs. The axle knees MUST have the holes for the radius rods. E-mail: koshagrez@gmail.com They must be in good shape!

hi folks, i spent a few hours removing the old steering wheel off my 1973 ford 2000 tractor, and thought it be a breeze to install a new one but it wont even go down by using a large socket and...

I think its a 1968 but I'm a little confused by the stampings because they are worn and hard for me to read. Any help is appreciated.

I'm in desperate need of getting some discs, and can't seem to find a set of used ones in good enough shape. I was considering buying a set of County line 7' heavy discs. I've got a 3 cylinder gas...

Help! I have been using these forums for a wealth of knowledge while rebuilding my 1971 3-cy diesel Ford 2000 machine. While I have the loader assembly off of it, I am trying to fix all of its...

my hydrauic lift has been acting u for awhile in cold weather the lift will not lift for about 30 min. and when it does lift it trimbles and is very slow. I have the cover gasket set to rebuild...

I've got 3 cyl Ford 2000 gasser and was having trouble finding out what the biggest size discs that the tractor could handle. Wheel base is 74 inches I believe. I was looking at one for sale that...

I have 1966 ford 2000, the lift will raise when you crank the tractor and stay, I have no control on the lift.The only way to lower the lift is to loosen the bolt under the seat, to let the...

Awhile ago an elderly neighbor of mine gave my and my brother her past husband's Ford 2000 lcg, we got it running recently but found the selecto speed cable was broken an had to open the...

I've got a 1970 3 cyl Ford 2000 with live PTO. I drained the rear oil today and went to remove the pto shaft to replace the oil seal and bearing. To no luck, I wasnt able to get the shaft to come...

As the title says, I've got a 3 cyl Ford 2000, I believe it's a '68 but the specific year shouldn't matter. On the right side of the tractor, there are 2 lines (1 larger 1 smaller diameter)...

EDIT: HOW CAN I DELETE THIS?? I FOUND THE FORD SECTION TO POST THIS IN AND DIDNT WAMT TO HAVE THIS DOUBLE POSTED. IM NOT SEEING A DELETE BUTTON ANYWHERE. MAYBE A MOD CAN HELP ME?? First off, I'd...

Yesterday I was clearing my driveway of about a foot of snow using a box blade and suddenly had no steering. The steering arms are not moving at all. There were no feeling or sounds of anything...

1971 Ford 2000 Gas, 3 cyl Installed a new voltage regulator because battery was not charging, generator tested OK. Afterward, I checked the voltage at the battery, which appeared high at over 16...

I traced a recent problem (battery not re-charging) to the "voltage regulator" and replaced it. Afterward, I checked the voltage at the battery, which appeared high at over 16 volts, around 1.500...

I am new here and thought I would show a pic of my tractor. It is a 1972 Ford 2000 3 cylinder gas with what I think is a loader from a 3400. I have had it for about a year and first thing I...

I recently bought my first tractor. :) It had been sitting for several years. I pulled "a dipstick" from the right side (driver's right) of the engine and it's dry. I've added 4 quarts and...

Observed the problem a few hours ago, where battery begins dragging, then eventually dies. Belt seemed loose, replaced, no change. Charge light doesn't work, but voltage at battery @ 1500 RPM is...

Hi, My 4 cyl. 2000 smokes whitish and smells like unspent fuel until it warms up, then it mostly goes away. I thought it took an awful long time to warm up- I had it running at 1500 rpm or so...

I am trying to replace one of the clips that holds the lower grille, and cannot get these aftermarket clips to pop into the rectangular cutout. The other OEM clip will pop out and back in, but I...

Sorry... duplicate.

Hey guys, So I've got my 1964 Ford 2000 running and working great. I finally got all my projects done and the last repair to make was the proofmeter. It wasn't working, and I was going to run...

I am looking for a quick attach converter for an old Ford 2000 with a Ford series 703 front end loader. I do not weld and don't know anyone nearby to do it for me. Does anyone know of a QA plate...

Please help! I have a 2000 Ford (4cyl diesel) tractor. Hydraulic lift had been working erratically for a while but then a couple of months ago it just quit lifting altogether and I am just now...

:newhere: Bought a 1956 Ford 600 from my brother in law. Came with a mower deck. Unloaded it yesterday, started right up. Mowed for 10 minutes and it stalled. Could not restart. Turns over but...

I changed the engine oil on my Ford 2000 3 cyl diesel tractor and put the specified 8 quarts of oil in the engine. The dip stick showes it to be over filled after sitting idle for a day. Do I...

HI guys I recently had a hydraulic leak on the piston pump. I fixed the leak and added hydraulic oil and primed the pump. Went to working just fine. Have used it off and on for the last 4 days...

Hello! This is my first post and I love this site! I have a Ford 2000 model# B1023B and Serial # C479709. I think its a 1975 model. It has a Zenith Carb. and the Tab numbers are 02 07 and 13915B...

I was using a box blade when i hit a buried stump. I wasnt going fast but it still hit hard enough to stop the tractor. Anyway, from that point on the lift doesnt function right. It will lift all...

Hey guys, So I finally got my old 1964 Ford 2000 up and running. Had a problem with it surging pretty bad once it was in gear and moving. I tried to adjust the carb but still had the same issue...

I bought a 1967 Ford 2000 the other day and the seller had a few of the sheet metal parts in a box. I put the steering column cover back on but I was left with this mystery piece. I've checked the...

Hey guys, I've read a lot of different arguments for using several different spark plugs on a 1964 4 cylinder Ford 2000. I'm wondering what everyone here uses and why.

I thought this would be easy to find out but not so much. I bought a 1967 (I think) Ford 2000 the other day and am going over it. The front nose bracket that connects the cowl to the front of the...

Hey guys, My parking brake pawls(#7) are both rusted in place, unlocked thankfully, and I am having a terrible time freeing them up so they'll pivot to lock into the sector plates(#10). I've tried...

After attempting to jump start, there is no spark at distributor. It ran fine shortly before, but battery would not re-start it, After charging battery, there is now no spark. It seems like I...

Hey guys, I have a 1964(correct me if I'm wrong on the year) Ford 2000 that I inherited. I've been cleaning it up and going through it to try to get it running again. I'm ready to crank her up for...

Hey guys, I recently inherited a Ford 2000 tractor that I'm going to get running to help me begin to homestead. I am having trouble identifying the tractor based off the serial numbers I'm seeing...

I have a early 60s ford 2000 with a 4 cylinder Diesel engine. It does burn a little oil when you first start it up. The issue is that after it runs 5 min or so it idles up and down from real high...

Hi All, I was under the impression when I just bought my 1964 Ford 2000 tractor that all I needed was a bill of sale from the previous owner, because tractor titles (at least for this year/model)...

I want to go from a generator to an alternator on my 73 Ford 2000. The generator is making a horrible chirping noise when the tractor is running. Is this a big job to do? Or would it be a...

I had such great help with my solenoid system, especially from souNdguy, I thought I would ask for more help with a hydraulic lift problem. The tractor is a 1963 Ford 2000. The lift was suppose...

I am attempting to remove the rear hood to paint it and have every step completed except I am unable to remove the throttle control lever from it's connections. Here is the rear hood with the...

Hi every body I am looking to buy a ford 2000 but the owner told me that there is a leak when you pour fluid into the rad it right way start pouring from the bottom of the block what it could be...

Just brought home what I was told by the seller was a 1975 2000 tractor, 2WD, 4 speed, 1 reverse, also included a bush hog. I downloaded a 900+ page pdf file which is apparently a scan of a...

I went with my father in law today to look at a Ford 2000 that was for sale at a very low price. He had it delivered to his house an hour later. It has a bad seal leak dripping out of drain hole...

got my pump back from the rebuild shop but when I connect the injector line they leak. I put new metal washers. Is there any thing else I can try to stop the leaking like tape or something?

I have a 1967 Ford 2000 with the 8-speed transmission and it's time for a fluid change. From what I've gathered, I need to put UTF in the rearend because of the hydraulics. But the biggest...

What do you use for nuts when installing new gauge cluster and gasket?

So, I finished tilling some summer plots and was about to load the tractor up for the day. I pulled the tractor up to the back of the trailer shifted into neutral to get off and move some stuff...

Ok guys I'm new to this but need some help. My ford 2000 needs an engine rebuild. I see rebuild kits with sleeves and some without. I have guys telling me it has sleeves and some tell me that it...

I recently purchased a 1974 Ford 2000 tractor that I am in the process of restoring. The tractor appears to have the original headlight fixtures, but the bulbs and headlight rings are missing. I...

As stated above. Radiator and hoses are new (summer 2014). The coolant leak started slowly a few weeks ago, occurs at rest and has gotten more noticeable over time. Just a few drops a day. It...

I've located a Ford 2000 3-cyl gas that has an 8-speed transmission (4 speed with hi-low ranges). I think I've read on this site that the 2000 also came in a 6-speed, and that version ran kind of...

Hello there! This is my first post. Just bought a 1963 Ford 2000 industrial with loader and 723 series backhoe. Having trouble with the hydraulics. I rebuilt the 4 loader cylinders to fix leaks...

Hi everyone, I am just asking for any and all information anyone has on a ford 2000. Model Code: B1013B Production Code: 8L4 Serial Number: B859647 I know what the model code and production...

I bought this tractor to put a small backhoe on because the JD did not have enough hp to drive the hydraulic pump from the pto I don't know if it was originally 6 volt. It has a 12 volt battery...

1971 Ford 2000, 3 Cyl, Gas - Has original instrument cluster, tach (proofmeter) was not working. Installed new cable from generator. It has begun registering, but inside the cluster, a gasket/seal...

Hello guys, I wasn't quite sure where to make my question, anyway... I bought a ford 3000 as I told but I am not sure if it's this model or the 2000 one. I am going to write the model's serial...

I think I may have gotten past the stalling, but I'm having trouble determining what happened. Symptoms/Chronology: 1. I had decided to go to a heavier oil 15w-40, verus 10w-30, in part due to a...

How do I repair a frozen clutch on my ford 2000

Wow, I'm such an idiot! With so few wires, I don't know how I could screw this up. Restoring my Pre 1964, 4 cylinder Ford 2000 and I'm simply wanting to start my 12 volt tractor using the...

First time on the site, this looks like an informative area. Thanks for taking the time to read my post. Working on restoring my grandpa's Ford 2000 (4 cyl). I've got three questions. All three...

Working on my first tractor project, a 1963 Ford 2000 (The first blue Ford tractor is its claim to fame). I submitted a post in the "other brands" forum concerning box arm adjustments, temp...

First time on the site, this looks like an informative area. Thanks for taking the time to read my post. Working on restoring my grandpa痴 Ford 2000 (4 cyl). I致e got three questions. All three...

I recently bought this 69 ford 2000 3 cylinder gas tractor with an 8 speed transmission with live PTO. When I went to look at it, the PTO and clutch worked fine. When I got it home I couldn't get...

Hi All, Long time lurker who has finally taken the plunge and bought a 1970 Ford 2000. Diesel 4 speed, Highways version, with a Safety Cab and auto hitch. No idea on the hours, but it appears to...

I bought a 69 ford 2000 gas tractor with 8 speed tranny. I have 2 problems. 1. The tractor seems to run fine in all lower gears but boggs down to the point of stalling in gears 3 and 4 high. 2...

New to the Forum; Any opinions about the Ford 2000, 1973? Do they have any sticky problems etc.?

So, Before I remove and maybe destroy something How much trouble is it to rebuild a hydraulic pump with the kits sold for this? Any step-by-step instructions? any help is GREATLY appreciated...

I have a Ford 2000 2WD 3 cylinder diesel tractor and am not getting fuel to the injectors. I had pulled the steering box off of it to rebuild and it wound up sitting approximately a year before I...

A friend has a '64 Ford 2000. His father bought it new, and always told him it was an 8-volt, positive ground. Everything I can find says they were 6-volt, positive ground. He has put an 8-volt...

Just joined up here, and been doing a lot of searching and reading. Have learned a lot, but still looking for answers on some carb issues on my 1963 Ford 2000, 4 cyl gas. Sorry for the long...

My tractor will not start, replaced battery and it started right up, a few hours later it would not turn over! Is this a voltage regulator? ignition switch? something is draining my battery.

Just as the title says. I'm working on repairing my top hydraulic cover. Tractor Specifics: 1963 Ford 2000 Industrial 4 cyl. gas, 4 speed I'd like to eventually find a new cover but right now...

Good morning all, my name is Dan Shields. I'm new to the tractor game but I have a decent bit of mechanical experience. Just wanted to stop in and say hello and thanks for answering all my future...

Does anyone know what size baler a Ford 2000 gas tractor can pull it has 36 horse power so they say

Found an early 1970s model Ford 2000 in good condition. Tires on tractor are like new and tractor comes with a bush hog. Tractor is a 6 speed and does not have power steering or live pto but comes...

I have located an early 1970s Ford 2000 that is in good shape. The tires are in very good condition and tractor comes with a bush hog. Tractor does not have power steering or live pto but does...

Looking to buy my first tractor. I have found a ford 2000 that has been fixed up (not restored).The guy selling it is a deisel mechanic He buys them , fixes them up and resells them. It is a 3...

New old guy here with a 1964 2000 3 cyl gas.I just got a new Zenith carb in and I need to know if there are any adjustments I need to make before putting it on and what adjustments after it's...

I recently purchased a used (obviously) 1974 ford 2000 which has a aftermarket fronted loader on it. My problem besides some control box leaks (not bad) is that when I raise the rear 3 pt the...

hi, I have a 1972 ford 2000 3 cyl. diesel with independent pto. I have removed release bearing hub support and front cover of trans. removed snap ring on input shaft but the shaft won't come out...

Hi folks How much play does the input shaft supposed to have. Mine wobbles quite a lot. Is this normal or do I need to change some bearing? Thanks Kenny

Hi guys, I have installed flywheel to crank 3 times and 4 bolts go right in but can not get the other 2 to start. What am I doing wrong? Is there a way to tell how to line up bolts and holes?

OK I am planning on selling my '68 Ford 2000 tractor, but I don't know what kind of price to ask for it. This is one of the 3 cyl gas models with a 4-speed manual transmission. The is the newer...

I bought my first tractor 4 years ago, a 1973 Ford 2000 with loader. With light, occasional use, haven't had any problems until a few months ago, when brake pedals started getting stuck down, and...

I need the correct size and hopefully where to buy freeze plugs for 1973 ford 2000 diesel. thanks for any info Kenny

I need some troubleshooting advice. New clean fuel, carburetor leaks a bit, air intake hose just falls off the carb, spark plugs look okay, tach does not work. Problem: tractor starts ok but...

Hey all, I just bought a Ford 62 2000 gas that is mechanically good to go with the exception of one thing. While driving it around, especially at low RPM, the engine RPM surges up and down...

Recently acquired a 1972 2000 Ford 3cyl diesel tractor for occasional use. Getting ready to service the machine and oil low on check. Needs to be added but there is no obvious place on either...

Need some advice. I have 74 Ford 2000 3-cylinder diesel that has no hydraulics. Since it was old, I decided to rebuild the pump and replace all orings and seals on the lift piston (under the...

I own a 3 cyl Ford 2000 and recently had the hydraulic pump replaced, including new hydraulic fluid. But now the lift is worse than before; it chatters and shakes, taking up to 10-15 seconds to...

How do you change from a 6 volt to a 12 volt charging system?

Just purchased a older used Ford 2000 Gasoline tractor not sure onthe year but would say its in the 60's since it has a generator on it rather than alternator .. My question I want to check the...

As a bonus at work I was told to go buy myself a new tractor. I said OK... But as an engineer I am spending way too much time analyzing the options. Here is roughly what I do with a tractor...

Anticipating tearing into the rear axle due to some hydraulic problems. Looking at eBay for manuals... are the IT manuals good or do I need an actual Ford manual? Any other better sources?

Looking at eBay... are the IT manuals good enough or do I need an actual Ford manual? Any other better sources?

I just bought a boat anchor I am afraid. If someone can help me,I would feel better,Please! Its a Ford 2000 N9 gas tractor and when I got it home could not get it off the trailer,because the PTO...

Hooked my old Ford 903 post hole digger up to my Ford 2000 diesel the other day and thought it was going to end up knocking limbs off a nearby tree or digging a hole to China. I had hardly any...

Hooked my old Ford 903 post hole digger up to my Ford 2000 diesel the other day and thought it was going to end up knocking limbs off a nearby tree or digging a hole to China. I had hardly any...

Just picked up a 1972 Ford 2000 with a 3 cyl diesel engine. The previous owner said the fan hit the radiator, he put in a new radiator, but put a electric fan on it instead of a regular fan. I...

Hello all, I am new to this site and need some info. I know this has been posted before but can,t find the right answer..LOL 1974 Ford 2000 3 cyl. gas engine with 8 speed high low trans, live pto...

I have a old Ford tractor in the garage and it is either a early 2000 or 4000 Ford diesel. It would be the smaller older tractors (like the size of the 800 Fords}. It has a 4000 decal on it and...

I have had this tractor for awhile now. I have been fixing issues as I move along toward hunting season. We are not trying to restore this tractor to show room condition, but I would like to get...

Hello folks, seems I am the proud owner of a Ford 2000 series tractor. Paid $1500 for it. Unfortunately a tree fell on the front & crushed the front top of the hood and grill and got the radiator...

I have a Ford 2000 3 cyl gas tractor my dad gave me after getting a new shiny John Deer. The starter is bad and needs to be replaced. I can easily remove the outside two bolts, is there a third...

I have a Ford 2000 3 cyl gas tractor my dad gave me after getting a new shiny John Deer. The starter is bad and needs to be replaced. I can easily remove the outside two bolts, is there a third...

Hello everyone. Im trying to find the correct color to paint my 1962 Ford 2000 rims. Im not doing a parade resto, just a little touch up.

I recently bought a Ford 2000 and it ran perfectly. However today while mowing down a steep grade I noticed a lot of oil coming out of a rubber seal by the shifter (wires coming out of the...

I recently acquired a 1972 ford 2000, gas version. I am looking to equip with a front loader and would prefer loaders originally built for this or similar models. I have about 50 acres to look...

This is by far the best forum on the net for tractor information. Thanks for making my life easier. Thus far I have been able to find a thread to answer my questions but this time I have come up...

I'm sure this has been discussed before...but can you review how much hydraulic fluid my machine takes? My 4 cylinder gas machine has been parked 15 years...should I drain, replace filter &...

My Ford 2000 3 cly gas tractor won't start. Backfires sometimes, sometimes catches but won't maintain an idle. Middle of a pasture fence project on a horse farm. Darn! I replaced all...

J275 A 115-504 is it missing some numbers? this was on a bracket with 2 bolt holes next to the starter on the right/ battery side thanks greg

I have a 1967 Ford 2000 gas tractor with an 8 speed transmission. I was brush hogging and almost done when the PTO shaft quit turning at its normal speed. Turning slow enough that I couldn't...

I have a 3cyl gas ford 2000. It just started leaking fluid out of a pinhole in the hardline under the right floorboard. I drained the fluid, cleaned it with brake clean and tried to jb weld it for...

Need some advice. A guy has a 1973 ford 2000 diesel he wants to trade me. The tractor appears to be in good condition. It has between 7500-8000 hrs on it. He says he has owned it since 1999 and...

looking for complete setup 730 or other loader that will fit a 73-74 ford 2000 gdecedue@cox.net

im looking for a complete setup for a 73-74 graple or frontend loader thanks or info as to what will work

im looking for a complete setup for a 73-74 graple or frontend loader thanks

hydraulic lift will not pick up. removed upper housing from lower to see if piston was stuck.it appears to be at least i cant move it.is there a way to free it up. ive tapped on it with a wood...

I just picked up a 63' Ford 2000 diesel. The engine has virtually no compression and wont run at all, even with spraying ether in the intake. I got the tractor for $550 and it is complete and in...

Can anyone tell me where do you add engine oil in a ford 2000 tractor? I think it is a 1962 year? I included some pics in hopes someone can maybe circle the area that I should be focusing on...

Hi all, I need some advice on my ford 2000 I removed the front cover and changed the gasket and seal and water pump. I took blots out of fuel injector gear but didn't think I let it turn any but...

Would a 7K car hauler be adequate to move a Ford 2000 (3 cyl) with loader about 100 miles? My friend just hauled an MF 50 over 2,000 miles on the trailer in question with no problems, but there...

HELP!!!! My tractor is killin' me. The bowl/seperator fills and then it wants to go down half way and causes the tractor to spit, sputter and cut-off. I have blown the lines clean, replaced the...

Hello I have a ford 2000 tractor (gas) I dont know what year it is my grandpa bought new when they first came out so I inhereited the tractor, I wanted to know if a Great Bend loader 330 well...

“Yesterday was yesterday and today is today” I had problems starting my tractor when I first bought it so I replaced the battery and yesterday it started and we used it without a problem. So...

My brother is looking at a later '60s 4cyl. diesel 2000, overall it's in pretty good condition, good tires, swinging drawbar. Haven't heard it run and the man wants 1500.00 for it, I think we can...

Just bought a 1973 Ford 2000 diesel, I bought it at an auction and while there it ran for three hours before I won the bid. I got it home and had no problem starting it, drove it around for a an...

Ive already asked a couple of questions on here and have had good responses that have reafirmed my thoughts. So here goes one more. I drained my rearend fluid so I could replace the brake pedal...

Is there a hyd filter and or a trans filter on this tractor? It's a 8 speed 3 cyl diesel. I've got it split and all fluids drained and I found some metal chips so I thought about the filters, but...

Hello, First post. So let me start with I just recently bought a 67 Ford 2000 European market (so I have been told by New Holland dealer); with an internal clutch spring. Tractor doesn't appear...

Well I have replaced the cluth etc on my ford 2000. Runs great! Now the hydraulics are not working. The 3-point lift does not function at all. I bled the hydraulic pump and it did not seem to have...

I inherited a 1952 Ford 8N and a 1968 Ford 2000 gasoline tractor when we acquired a horse farm recently. The 2000 is in need of TLC, while the 8N, used to pull the critical manure spreader was...

hello all recently bought a ford 2000 tractor need help with identification engine block trans and axle housing all have C5nn #s I'm familiar with ford autos and believe this is a 1965 number the...

Just bought this tractor and the hydraulics don't start to work untill it has ran for a number of minutes (sometime 20)

Has anyone ever attempted this? Are there kits out there? What are my chances of finding a scrapped out one and switching components? The non power steering is a bear to turn . Thanks in advance...

Anybody with an educated guess? Close ballpark?

Hi Looking for a cat 1 hitch tractor for hobby farming , tillage. I already have a kubota b2710 but would not mind having another tractor, esp for my 2-14 ao plow. The kubota does seem to strain...

I read quite a bit about rebuilding the manual steering box on the ford 2000, and attempted the job. Now the steering is giving me trouble one of two ways. It either will not turn to the stops on...

Can anyone help with bleeding instructions for Ford 2000 ? I had a hose go on the backhoe, refilled the fluid, and i apparently have a lot of air in the system because the loader now is having...

I have a 1973 ford 2000 diesel that i just completed a steering box rebuild on thanks to this site. However I managed to ding the threads badly on the steering shaft. I need to chase them before...

My ford 2000 is giving me fits. The entire due system has been replace: new lines, new filter, new fuel pump. Ran good for two cuttings of Hay and then just quit while I was driving it.....hasn't...

Hi all. I'm new to this forum, and new owner of an old tractor, a 1974 gas Ford 2000 with 6 speed trans. I'm trying to figure out what type of fluid to put in rear end and transmission. I have...

Ford 2000 TLB serial # 2888, with a Ford 730 Loader . Has a 3 cyl. diesel engine, hi-low trans,. power steering, live PTO with 3 point hitch. Backhoe is a BRADCO model 13 MD serial #BE436, it is...

Hi, I went to replace the generator on a 1967 Ford 2000, Gas, and found that the old Generator has two electrical connections, while the new generator, from Steiner, has only one Electrical...

Hello, First I would like to say thanks to the people that welcomed me to the forum. I have a ford 2000 late 60's model, and the hydraulics seems to have packed in. I have read on this forum about...

Ford 2000 TLB Here is a running machine.. Has a 3 cyl. diesel engine, hi-low trans,. power steering, live PTO with 3 point hitch. Backhoe is a BRADCO, it is tight, and well cared for, (not a...

Hi, I am looking to get a new battery for my 1967 Ford 2000, 3 cyl, Gas. The current one says 530 CCA on it. Do I need a battery that large for a Gas tractor ? I will be using it to plow snow...

I am a brand new homeowner with 5 acres. I have never owned a tractor and am looking to buy one for mainly mowing and general chores. I have found a 1964 Ford 2000 for sale. The ad reads... 1964...

Will standard hydrolic oil work in the hydrolic system of a 1969 Ford 2000?

I am considering purchasing a Ford 2000 Super Dexta. I was originally looking for a MF 135 but I cannot find anything in my price range of $3000. I then started looking for a MF 35 but I want live...

I have a 1973 Ford 2000 3 cyl gas tractor that leaks where the fuel line connects to the shut off valve. The fuel line and associated parts are 'not serviced' anymore. Does anyone know where I can...

Just found this site a few days ago. Would have saved a lot of money had I found it earlier. I have had this 1965 2000 3cyl diesel since 89 and have made many repairs to it over the years...

Hi folks, I am replacing the clutch, pressure plate and throw-out bearing on my gasoline 74 Ford 2000 series tractor. I have the service manual, however, it does not explain how to remove the...

Hi folks, I am replacing the clutch, pressure plate and throw-out bearing on my gasoline 74 Ford 2000 series tractor. I have the service manual, however, it does not explain how to remove the...

Hello I have been in the market for a Ford Loader to mount on my 68' 2000. I found one but not sure if it will fit. The model number on the tag says I9-97 and the serial number is 7355 I think it...

Hope i am posting this in the right spot. I am new to this site and new to owning a tractor. I have used them my whole life just not owned. I have some questions already. I want to change all...

My 3 Point lift links are stuck in the up position. I have read the trouble shooting guide in my Ford Shop manual and it does not address this problem. My owners manual does not address it ether...

I was looking the motor and noticed that the vacuum advance line to the distributor was loose. I tried to tighten the nut , but it was tight . however the tubing was loose and rotates inside the...

1964 Ford, 2000, 4cyl, 4 spd. Can't get it out of second gear. Took of shifter cover, all looks okay, but obviously something is broken or worn out. Any help?

I am presently lucky enough to have a knowledgeable friend helping me get this tractor working again. It was hijacked and ran into the woods, the transmission cable snapped and we aren't sure...

I have removed the return line and filter from center housing but cant figure out how to remove the back pressure body from the pipe and this has to be removed to put new filter. ANY ideas will be...

I recently purchased a 71 Ford 2000 and implements for $4500. The implements included are a two bottom plow, disk, 5 ft grader blade, a subsoiler/middle buster, a cultivator, and one of them 9...

Can I drill and tap a hydraulic connection so I can use a hose instead of the pipe on my ford 2000 tractor? Its got the wierdo fitting that hydraulic shops around here cant make a hose for and...

Hi all I have a problem with my Ford 2000 hydraulics. I have the lift cover off and return filter out but the suction filter/pipe is under the pto shaft and engage mechanism. I have tried and...

It has been one thing after the other with my 3 cylinder gas burner this spring/summer after running like a top for years....so here goes. Earlier this spring I went to start my tractor and it...

It has been one thing after the other with my 3 cylinder gas burner this spring/summer after running like a top for years....so here goes. Earlier this spring I went to start my tractor and it...

Ford 2000 1973 model Hydraulic problem I have a problem with the hydraulics. It will lift but it is slow and jerks as it goes up. It will hold it up all day once it raises. The lift lever also...

I have a problem with the hydraulics. It will lift but it is slow and jerks as it goes up. It will hold it up all day once it raises. The lift lever also seems real loose, The bush hog will drop...

bush hogging the local private school field next to my house this past week, I had the front bumper fall off and as it did, a corner of it got caught up around this part here knocking it loose...

Have a 1970 3 cylinder Ford 2000 gas burner. Have had a fuel starvation issue and local New Holland / For dealer suggests I put an in-line electric fuel pump between tank and carb and block off...

Need to find a repair shop near Franklinton, La to rebuild generator or assist in coverting to an alternator. Thanks

Need assistance finding a governor repair shop near Franklinton, La

The hydraulics on my tractor just recently quit working. I rebuilt the pump(had several broken springs). Once I got it primed, it worked great. I used it for 4 hrs., no problems. Now every time it...

75 Ford 2000 3 Cylinder OK, so my search for a tractor is over, I have the '75 Model 2000 3 Cylinder, and how I got there is in this thread...

I searched this forum but didn't get any hits. I'm looking for information on where I can get ignition parts, thermostat, filters, etc. for my 65 model 2000 3 cyl gas. I believe a Motorcraft...

I found a great deal on a FEL ($600). The loader is for a Ford 2000. Will it fit my 336D? If so, how much modification it will require? I don't mind doing a bit of welding, but I'd prefer...

During the winter, some rats or something got into the wiring in my 3cyl diesel 2000. I want to try to re wire it myself because not all of the wires new replacing... I just don't know the size or...

I have a 73 ford 2000 & would like to pick up a loader for the tractor - two arm - I would appreciate any help with model numbers so I can search for this. Thanks, Don

I have a 3 cyl gas '65 Ford 2000 that is perfect except after a half hour or so the power steering fluid starts flowing out of the top of the steering column all tan and cloudy. The reservoir...

Hi guys, I'm new here. I recently bought a 71 Ford 2000 3cyl. 6 speed with lift problems. The lift was only working part of the time, and very slowly when it did work. However, it would hold up...

Hello, I'm new to TBN. I live in Royal, Arkansas (located just outside Hot Springs National Park) and have 14 acres that I play on. One of my toys is an old Ford 2000 diesel tractor that I really...

Has anyone converted their 3 cyl. Ford, to a spin on oil filter..?? Seems like it would be a lot handier, and more economical to do. Since the new gaskets for the old cartridge type come folded...

How do I go about fixing the hydraulics on my old tractor? It is slam worn out. It can run 45 minutes, sometimes it will lift the box blade, sometimes it will not.... It has been a great...

The lift on my Ford 2000 is not working properly. When the tractor is cold, it takes several seconds (about 20) for the lift to come all the way up. When it's hot, it works better, but still...

I'm about to look at a late 60's Ford 2000 with loader. Gas engine. That's all I know about it at this time. I'd appreciate comments on this model tractor. Things to look for, pros and cons etc...

Hello guys, I have a 1972 Ford 2000 tractor, and when i engage the PTO, it will spin just fine. But when I attach my bush hog to it, and then try to engage the PTO, it will grind badly and will...

Hey guys, I recently "inherited" this tractor from my grandfather. It had sat for years without use, and I've got it running well after replacement of the fuel lines, new diesel(learned how to...

HELLO I'M A NEW MEMBER. I HAVE A 1967 FORD 2000. HAVING TROUBLE WITH PTO. NEED DIAGRAM OF THAT YEAR MODEL TO HELP REPAIR . THANKS

HELLO ALL, GONNA SURPRISE DAD AND RESTORE HISMOLD TRACTOR, NEED HELP WITH YEAR?. TRACTOR # C296472,TRANS # C7 NN 7006 AK,MOTOR C 9 NN9425 E, MODEL B1012B. ANY HELP WOULD BE GREATLU APPRECIATED.

This is my first post although I have been loitering on a daily basis for several months now. Ford 2000 Model Number: 21201 Ford 2000 Serial Number: <> 4162 <> Below I have cut and pasted the...

I have a 1973 Ford 2000 3 cyl tractor with a 3.8 stroke engine that is in bad need of a crankshaft! If anyone knows of someone that might have one, please let me know how to get in touch with...

Where exactly is the filter and how do you replace it. i have one and need to change it and service the 3 pt. the tractor is slow in lifting and i am going to replace the pto seal. i have a...

I have a 1973 Ford 2000 3 cyl gas tractor with a 3.8 stroke engine. I am in need of a crankshaft. Does anyone know where one can be found?

I have 1968 ford 2000 3cylinder diesel. I was playing with the draft lever(directly under seat on right) it was in a vertical position.(Position control) I pushed it down (Draft), now I can't put...

i have a 1975 ford 2000 diesel. its was running fine then one day it sputtered and died. i have changed the fuel filters both inside and outside the tank. Drained the tank, blew out the fuel...

My 1975 ford 2000 raises the bush hog up to max height as soon as the engine is started. This crunches the drive shaft into the mower housing and will melt metal if the shaft is turning. If I...