Long time lurker, first time poster. 1949 8N with front distributor that has been converted to 12V and not by me. I am somewhat mechanical but don't know much about carbs, distributors, points...

OK, all you purists can shake your fingers at me. I have wrecked a perfectly good Ford 8n to make it into a Hot Rod Tractor Name - Frank-N-Ford. OK, this has been my side project for a while...

New member here! I have a question and looking for advice! We have bought a 5 acre plot and plan on building a house, pole barn, long gravel driveway. And maybe have a few animals. The land is...

So I’ve always been really into tractors, both grandfathers are farmers. One has a really old Ford 8N, early 2000s New Holland farm tractor (couldn’t tell you exactly what it is) early 2010’s sub...

There is a 8N in good condition near me for sale. Has been cleaned up, repainted and appears to have no active leaks. Tires are good no signs of dry rot or serious damage with about 50% life...

Hi all im new to tractorbynet form.I have a ford 8n front mount dist. i put new coil points and condenser and rotor button and cap on three times still no fire. I know i cant have 3 bad coils and...

This Spring, I took my 1952 Ford 8N (I have owned this 8N for about 5 years) to the local New Holland dealer for some maintenance work. At the time, the 8N was running, I had recently changed the...

This tractor is a 6V system. 1951. New armature in generator and new battery (before the gennie was found to be at fault) and a new voltage regulator 8 weeks ago. Today I received the dreaded...

Well, here we again...:eek:...another 8n basket case just pulled up in our small shop. We have done 2 8n's, 1 ferguson and a 1963 JD 1010RU...like a glutton for punishment...last week we purchased...

I have a 1952 8N with Sherman over-under in good shape. Using an Awesome Henry kit, I am putting a Windsor 351 Ford into it. Don at Awesome Henry has been great with information and ideas...

hey all new to the site and new to 8n's. I picked up a 1950 to 52 8n, it hasn't ran in two years. when i bought it the guy told me the it didnt have a spark. so i clean thing up so i can see...

I know this must be a common question, and I hate bothering people. BUT from what I've been reading here so far there are alot of junkies on here that love to just talk tractors, and thats never a...

I have a 1947 8N, with a front mounted distributor. I've read all through the archives, and can't find much info on carb problems. I normally take the carb apart every year, and clean it good...

I really need this tractor to work... It worked great for a while after I bought it but now doesn't start. I am at the point of just buying another tractor because I need a working one.... But, I...

Anyone heard what the price is on the new Boomer 8N's? Thanks

1.) I know I'm not the first to do this but I tried to jump start my 8n with my pickup before I knew anything about the tractor. Believe it was flooded but not relevent now. Didn't realize...

I have repeatedly read that the slowest gear on an 8N is too fast for a tiller. I have a 60" tiller for use on my Ford 1920, and am wondering if I could also use the tiller on my particular...

A problem has cropped up with my Ford 8N. I use the tractor primarily for bush hogging, and the tractor ran fine at the end of the season last year (around October). I did not use the tractor...

I'm looking for anyone who has used a 4-6' 3 pt. rototiller on a Ford 8n tractor. I'm considering purchasing one but I am wondering if 1st gear will be geared down enough for it. Looking up on a...

Hi, I am in the market locally (Houston-ish) for a tractor. I have found two that I am looking at and they look almost the same to me. One is a Ford 9N and the other is a Ford 8N. They both are...

Starting a slow restore of my 8n not for show just a good cleanup. Was getting where it would miss a lick once in a while so I got a tractor supply tune up kit. Installed and fired right up all...

After much agonizing, deciding, and re-deciding, I pulled the trigger on the purchase of a new (well, 2009) New Holland Boomer 8N from Tim at New Albany Tractor Sales in Indiana. I bought it with...

Hello to all the LS owners on the forum. I've owned, maintained, and operated a 1948 Ford 8N tractor for the last 23 years. I have 6 acres and I use the 8N mainly for brush hogging our pastures...

Do you suppose he could be a secret TBN member? Way to go Jay! You look good gettin' some seat time. :thumbsup: Jay Leno's Garage

I just bought 12 acres of land and am looking for a tractor. Found a 1952 8n that looks to be in good shape but just not sure about something that old. Also any other suggestions on the type of...

In my quest to find something to mow my excess acreage I have ended up with a Ford 8n (51 vintage) and ford 951 5' brush mower. It seems to be pretty solid but has a couple of things that need...

After reading numberous posts/pages/website/visiting dealers, I am down to these two options. Here are the uses for the tractor: Here are our plans for the next 6 months: 1. Clear out some...

I tried to start my 8N today after a few months of no use, with no luck. It turns over fine, but just won't fire. I pulled a spark plug, cranked it over, and was getting no spark. I pulled the...

My dad has a Ford 8N (know this from previous research). He was using it several years ago and the implement snagged on a large rock, rocking the tractor enough to dislodge an ill installed fuel...

Went out to start the tractor and I have no oil pressure. The oil level is high enough on the dip stick and should be alright. Where should I check first? Speedy:)

I own a 1952 Ford 8N and my neighbor recently bought a new Kubota L2501. Yesterday my neighbor let me use his new tractor to mow my fields and I wanted to provide a compare and contrast of old vs...

The other day my 52 side mount 8n oil pressure dropped down and I changed the oil, it was time anyway. It was down low, but still running fine. I changed the oil, replaced the filter, and now the...

I got a call from my dealer that they were going to have one of the new 8n boomers for a few days so people could check it out. I have to say the cvt trans would take a while to get used to. First...

I start this tractor, when not in use, a couple times a month to keep the battery charged and fluids flowing. I started it about a month ago, ran fine. Went back 2 weeks ago, only cranked with...

Hi, Just a quick introduction, my name is Kyle and I just got my first tractor, a 1949 Ford 8n. I included some pictures and I will probably have lots of questions along the way. My first...

Drove the tractor up to the house one day to take out the trash, it fired up fine as always. Parked it by the house and did a few other things for an hr or so. Went back to take down the trash...

The tractor has been running fine until the other day. I went to start and had some firing issues. I had to jump it. Still no fire. I stopped and checked the fuel for water and got back on and...

I've been lurking around this site for awhile and have decided to ask for opinions/Advice about buying an old 8/9N Tractor. I eventually will buy a new Subcompact for my land, but untill I move...

I have a Ford 8N tractor which was recently purchased in very good running condition. It was built in 1947. It has one problem with the steering. When the steering wheel is turned in one...

I was talking with my NH sales rep in Bangor last night and he was told to give a last years leftover 8N, with FEL, away for 28,000 CASH. They won't do it if its financed. Anyone interested...

There is an farm auction here locally, it a farmer selling his farm and retiring. He has 6 tractors, 2 are Ford 8N's. We're thinking about buying one. Can yall tell me what I should look for to...

Looks well used and in need of work. Asking 1500 but was going to offer 500 if it ran. Thoughts

You guys on TBN remind me of all the guys I see out there on one of the other boards for the Ford 8Ns.... You're a bunch of great lifesavers... THANKS for all the excellent advice I've read thus...

I am thinking of converting my new to me 1947 Ford 8N to fuel injection and Electronic Discharge Ignition System and do away with the old carb and points and condensors. It would maintain the...

Hello I've been reviewing your site for some time now and found it to be very helpful in our search for a new tractor, thanks for all the great info. In the end we did a lot of looking, test...

I finished bolting the genny down to the pallet, and then put the pallet on the carry-all, and adjusted the pallet with the pto shaft hooked up to get everything correct, and then bolted the...

I posted a while back that I was close to buying one, well I did get that job done. It came with a loader and a 7ft Farm King blower. So far I've only had one opportunity to really use it moving...

does any one have any ideas how to add weight to the front end of a ford 8n, i have loaded tires, but i how like to keep the front end a little closer to the ground when towing cedar. especially...

I'm looking for a little help guys. I picked up a ford 8n and after doing a little research on the web it looks like my 8n has 9n rear wheels, is this possible I checked all the numbers and so...

Is anyone using a tiller with an early 8N (pre live PTO)? From what I understand the tractor is too fast in first gear, around 3 mph, to work right.

Hello everyone! I am new here at tractorbynet. I have a 1952 ford 8n with a 6ft howes bush hog. (Yes, I know it is to big but it was dirt cheap :thumbsup:. It weights between 750-850lbs. My...

I just purchased a Kubota M7060 and really like it. However, I think there's a few things where a smaller tractor might make sense. Would it make sense to buy an old Ford 8n for smaller cutting...

I'm changing the oil in a 1949 Ford 8N. The existing oil was very dirty and there was sludge in the bottom of the oil drain plug/screen and oil filter housing. The existing oil type in the...

I recently changed the brake shoes on my Ford 8N tractor. When I replaced them, they did not stop the tractor any better than my old shoes that were worn out. I used the Intertec FO-4 manual to...

our 1951 8N is beginning to make a "clicking" sound in the front right side of the engine. I wondered if this was due to a "stuck lifter" and in the process of investigating it, came across a...

Can anyone help me figure out a fair price for this tractor? I know nothing about it, other than it's a late 1940s (based on info from previous owner); loads of new parts/paint. haven't tried to...

I am currently restoring a 1952 Ford 8n. I was wondering if anyone knew how much red paint I would need to purchase. I have the tractor torn down to the frame (engine, transmission/lift and axles).

Built a complete loader attachment for a Ford 8N and shortened the Deere loader arms. Note the full subframe under the stock 8N.

I was shredding my monster foodplots and broke my steering on the 8N. I had to finish by stomping on the drag link to steer to the left. Took the tractor to the shop yesterday. I'll be taking...

Hi all I just got a 52 ford 8n that had been in a field for quiet a while the told me somethang was wrong with the hydraulics on it so got it home had to buy a carb for it got it running adjusted...

MY 1947 8N HAS ALWAYS STARTED UP NEARLY ON CONTACT WITH THE STARTER SWITCH. YESTERDAY I STRTED IT DROVE ABOUT 100 FEET, TURNED IT OFF TO GREASE MY MOWER AND NOW THE TRACTOR WILL NOT START. THERE...

My history with this tractor goes back to around 1969. I was 5 years old and it was owned by our neighbor across the street. He was fairly well off financially, having the top union job at the...

I purchased a ford 8n but it is in wyoming and I live in bend oregon I just wanted a old tractor to play with but now I find the shipping costs are way high Twice what I paid for tractor I don't...

My reliable ford 8N won't start! It works 50% of the time now. I tightened the very loose positive and replaced the negative wires on the battery. When I turn the key, make sure it is neutral and...

Well.. once again.. my 8n proved its worth, and impressed the wife, by pulling storm duty. When the huricane was predicted to hit.. we gathered up our semi-free range chickens in pens and stowed...

May be horse trading my Ford 8N plus implements for a Kubota B5200D 4x4 -- no loader. I have done a lot of searching and checked out tractor data. I am new to tractors and diesels so I am trying...

I just rebuilt the carb and it dies on acceleration. I have no idea what's going on. I have new fuel, clean lines and it can't get up to 2000 rpm, separate from the gov even. I've adjusted all...

I keep getting Battery Drain. New wiring harness, rebuilt alternator, new on/off switch. I just put a new battery in and it drained to dead. Charger won't light up when used? 6 volt system with...

i have a '52 8n tractor. last week while cleaning my drive way it started to loose power so i stepped on the clutch and it regained power, so i nursed it back to the garage. Now it wont start...

Been working on it for about 3 weeks and I still cannot get it to run. Have put in new points, plugs, coil and it still will not fire. Any suggestions on what to try next would be a lot of help...

Its been like this a few years, can't do much with it, A few years ago it was overheating when bush-hogging, and its been kinda just started and moved here and there while I think of how to fix it...

I’m curious of the comparison if anyone has experience with these. I only see videos on the older Fords pulling 2 bottom plows etc. What would be the similarities or differences to a mahindra...

Hello fellow tractor enthusiast, I'm new to the forum and this is my first post. So i have a Ford 8n and i was looking into power steering options, and for those of you who have also looked into...

Good Evening. After turning up my tractor this evening I had it running for about 30 minutes. During that time I noticed a lack of power, so I started poking around while it was running and I...

I noticed a tractor in the local classifieds that looks like a similar tractor to one of these. They are asking $2100 Canadian. I don't know the shape but seems alright. What's the average cost...

Good Day! After reading another thread related to prices for Ford 8N’s, I thought I would try to get some input on an 8N purchase I am considering. In this case, the tractor is owned by my...

I have a 8n put new point condenser plugs wires cap, it has the original 6volt system still I crank it no start as soon as I hook the jumper cables to it fires right off runs perfect shut it off...

Was searchin craigslist and saw this tractor - Just had to share it 1952 8n Ford Tractor with track converstion

Merry Christmas All: Some background: I live in Northern Alberta on 63 acres of forested, very hilly land. By February, temperatures can and will get as low as -45 degrees Celsius, -49 degrees...

If you listen to this engine in this video, the engine sputters and almost dies... then, revs back up. You will notice that the engine is never stable and a half throttle it almost dies and then...

I bought a house and 2 acres a little over a year ago, and have been slowly cleaning out the back acre, which was so overgrown with tallow trees and vines that I couldn't see much more than a foot...

I've got a 1952 ford 8n. After I finish restoring the sheetmetal and body work, and incedentals, I'll probably service it. I've heard just about every type of oil sugested for this engine ( flat...

I am new here and I need some help to help a widow I know. She has two 1950 Ford 8Ns that turn over but will not start.They did run about three years ago. They have been sitting since her husband...

As noted in the title. The problem began 5 days ago with an occasional high pitched whine prior to the Starter properly engaging the flywheel and cranking the engine to life. Over the past few...

Advice, please, on a suitable trailer to haul a 1949 8N Ford tractor behind a 1997 Toyota Tacoma six cylinder straight drive 4wd equipped with a towing package. Thanks!

I am looking at a 1949 8N that the owner claims the only way it will start is by pull starting. He said it smokes and will start with starter after pull starting for the day. I kind of guess...

Hi there. I've never posted but have been reading for years. I have an 8N that has a problem with the lift. Last year at the beginning of the season it didn't work initially but once it started...

My '49(?) Ford 8N tractor (front distributor) quit on me, and I saw that gas was running out of the bottom of the carb lower body. Closer inspection revealed a recessed screw had fallen out. I...

I just bought this tractor at an auction. I brought it down a steep hill down to the lake. It had a very hard time getting back up the hill and it stalled out 3 or 4 times. (too much load) At...

im considering buying s ford 8N. i have always heard they have always been awesome tractors, very stable ( I have 12 rolling acres) to bushhog, . I also have a need for a front end loader. Can the...

I Currently have a 1952 ford 8n. I am going to look at a 1965 ford 2000. I know it does not have power steering. He said he thinks it is a four speed but it does not have a hi or low. It is a 6...

I have a friend that is looking at buying a Ford 8N tractor. Are there certain things that he should be looking for that are model specific problems. I am trying to help him with a little basic...

Evening all, I've been browsing these forums for info a while now and got around to registering today. Lots of smart people here! My question lies in an 8n I'm looking at buying. I'm going to look...

I have a 1950 Ford 8N Tractor. I lifted the plow and when the engine is off it very slowly settles to the ground. It does this wether or not the pto lever is forward or to the rear. Is this...

I have a 1952 ford 8n tractor with side mount distributor. It will not start. There is fire at the points but but at the plugs. New wires, distrubutor cap, plugs with gap verified .025...

Looked at a buddy's 8N Ford tonight. Ran fine last week when he parked it. No spark now. This fellow bought the tractor last summer but is the original shade tree mechanic. No meters, lotsa...

Hello hope everyone is well. I have my believes to be 1952 8n Ford tractor and was wondering if anyone knows a great service and repair manual that shows in-depth repairs and maintenance of these...

hi guys just unloaded my 8n from a friend needs some TLC he has converted it to 12 volt it has front mount dist. he said it has problem cranking now not in the carb or fuel system going to check...

long story short I was pushing a a little pile of dirt over with my loader and the tractor stopped, without warning. No gears (forward or backwards) but I have Hydraulics . So my question is Are...

I removed the side mount distributor from my 8N tractor and seemed to have messed up the timing. I think I turned the rotor shaft. How do I put it back on correctly?

I was mowing the other day and when I left the tractor I noticed what looked like water running down the side of the block, just above the starter. I traced it back to the mating surface of the...

I just bought a 1951 Ford 8N for my first tractor and I am pretty happy with it so far, except that I recently noticed that it doesn't have the correct center housing on it, ie the old 9n/2n style...

I'm restoring a '52 ford 8N. This will be my first tractor restoration. Any tips and/or tricks. I've ordered my replacement parts from www.just8ns.com and am having a machineist make one part...

I keep my 8N outside, so it gets exposed to the cold here in Ohio. It starts right up without any problem, though. However, this weekend when I started it up I had a problem. Specifically, when...

i have a ford 8n i turn the pto on with tractor in nuetral and the 3 point will lift the brush hog right up but as soon as i press in the clutch the 3point will drop it right to the ground how do...

I just bought my dad's old 8n Ford and need some help to get it running.I need new spark plugs ,points and all that stuff. Is there a kit available for that and where?? I also need to change the...

Just bought a semi-restored '52 8N. Saves me about 3 hours a week in mowing time. Looking for more seat time, but I have cut, hogged, and plowed up about everything on the property. Lovin' every...

Hello Everyone.. been awhile since I asked a question.. but need some advice.. my 8N Ford 1952.. never had the tranny/hydrolic oil changed.. as far as I know.. so it is time.. I do have it...

Is it common for rain water to leak into the crankcase on 8n tractors that have been sitting outside? If so, what is the likely source of the leak? I was never much of an 8n fan, but now I'm the...

Hi. I've been lurking here on and off for a while. I have pretty much resolve most of my problems from this board and others. Now I'm stumped. 52 8N side mount dist. Over the last couple of...

Went to check my voltage output for my alternator yesterday and my volt meter went crazy as soon as I touched my negative lead to the battery terminal. I'm wondering if a bad diode or voltage...

Hello all, I have a question regarding my 1949 Ford 8N tractor. It has been converted to a 12V system (before I purchased it). It's haveing some trouble starting now--no spark, and as I look...

Figured I would ask here as it is likely to get more traction then in the vintage section...... What size finish mower would a HEALTHY (as in just rebuilt) 8N be able to handle? Thanks guys...

My 8N ran good for 25 years then quit. New starter, coil, went through all wires and connections. Then started buying parts. Caps would not fit. Rotors wont fit. I'm ready for a new...

Ok a little history about it. i bought it in march of 2010 for $800 It needed a rad and had a cracked block i welded the block and hasn't leaked since. heres all what i put on it since i owned...

Hi all, first time poster on the forum. I have a 52 Ford 8N issue I need some help with. I was clearing some brush recently and noticed that the RF tire is rubbing against the back of the bolt...

I need to replace the waterpump on my uncles old Ford 8n. I've never worked on one before, and thought I'd ask if there are any tricks or tips, or if it's pretty straight forward...

Here’s the situation. Bought the tractor back in 2020. Started up nice and easy. Was always pretty easy to start until I parked it for a month maybe in late fall 2022. Went to start it up and it...

Hi this is my first post so I am not sure this is where it belongs. On my ford 8n I recently broke the seat bolt while trying to remove it (It is sheared off nearly flush). I attempted using an...

Hello, We're needing to replace our 8N with something that has more traction (BIG hills here!). Does anyone have a recommendation of a unit (gray market) that has a locking rear? Or would you...

I am considering a Ford 8N with Sherman over-under drive and a 661 Workmaster with live PTO and power steering. For $600 more than the 8N, the 661 is probably the best choice. The 8N is a...

I bought a 48 Ford 8n a little over a month ago. It started the first week I owned it but not easily. After the first week I had it the starter burned up and the flywheel teeth broke. I have since...

Hello to all! I just recently purchased my first tractor, I believe it is a '52 8N, but I have not been able to decipher the s/n just yet. However I do know it is a later 8n with the proof meter...

Looking forward to find answers and help others where possible. Also getting ready to DIY Pole Barn, most likely 30X40X12/ using metal truss and looking for any suggestions to get it done in the...

Hello all, I am new to the site and living in Mebane, NC. I have a Ford 8N (1948 or 49, I believe). I've had this tractor for about a year and kept it running (mostly!). However, I have all...

Anyone ever installed live hydraulics on an 8N? How big of a job, and how expensive was it?

The three point on my '47 8N does not want to raise all the time. If I play around with the lever, it will eventually come up. Someone once mentioned to me that there is a pin inside the housing...

Hello from Oklahoma! Thanks for the warm welcome. Especially kind people on this site. My very first question for my husband and I forgot to add the make and model (first time I promise-so far)...

My 8N began to run rough and died a couple weeks ago and I've been slowly reading forums. Points, condenser, coil and plugs are all new in the past 6 months. Have spark at plugs. I think it's a...

8n ford\'s fan,s Are their any 8n Ford tractor buff's on this vintage tractor forum? My old 8N has been with me for 30 plus years. It has several modifications. I'd be interested in hearing...

1948 Ford 8N, pretty much in original configuration. I was skidding some trees out of the woods, and ran the tractor for about an hour, with no problems. Heading down my driveway I opened the...

I have a Ford 8N tractor that will not start, no fuel to the plugs, good spark. It has a 12 volt system. It was running well when it just quit. I checked the intake manifold it's clear and...

Hi all, I have a 52 Ford 8N with side mount distributor. I've just given the tractor a full tune up including: points, plugs, wires (copper core), condenser, ignition, wire harness,and pertonix...

Trying to find what size/model baler that can be used with an old 8n. Not concerned with manufacturer. Field is fairly flat and I don't plan to pull a trailer. Thank you for any assistance. Phillip

A little backstory on the 8n . I rebuilt the pump and installed a cam follower pin and new rings in the hydraulic piston last year. Lift worked fine with no weight in garage. But before i got to...

I noticed the fuel bowl has a very slow drip. I tightened up both lines on the valve but drips still form. I saw a couple on ebay for $14.24 and $13.20 with free shipping. One of them states the...

i HAVE A 1950 8N THAT I USE REGURLARLY. VERY RARELY IT APPEARS MY CLUCTH WILL NOT DISENGAGE AND I CORRECT THE PROBLEM BY CLIBIMG A HILL OR DEPRESSING THE BRAKE WITH THE CLUTH PEDAL DEPRESSED, THAT...

MY TRACTOR WOULD RUN ABOUT 2 MINUTES AND THEN DIE. WAIT TEN MINUTES, RUN GREAT FOR TWO MINUTES AND DIE AGAIN. REPLACED COIL, NO HELP. MADE SURE GAS CAP WAS NOT PLUGGED. IT ENDED UP BEING TRASH IN...

I have been doing some research on how to get my clutch working better on my 48 8N. The clutch takes between 3 seconds an 1 minute after i push the clutch pedal for the clutch to engage...

Just bought my first tractor. A restored Ford 8N with a brush hog for $3,500. I admit, I have never so much as touched a tractor before in my life. In fact, I am a little concerned about driving...

I recently inherited a Ford 8N which had been running but quit about 1 1/2 years ago. A neighbor (before I got it) figured it was the carb and took it apart and promptly abandoned the project! I...

I inherited a 1952 Ford 8N and a 1968 Ford 2000 gasoline tractor when we acquired a horse farm recently. The 2000 is in need of TLC, while the 8N, used to pull the critical manure spreader was...

I am going to look at a 1952 Ford 8n later today or tomorrow. I drove on on a farm back in the early 90s. What should I look out for in my pre-purchase inspection? I'm familiar with the hydraulic...

Recently (as in two years ago) we acquired a ford 8n tractor with a front mount distributor. Today I finally decided that I would like to do a tune up on it since the oil looked like it was 30...

Hello All: Need your infinite wisdom regarding my Ford 1948 8n. The hydraulics on my tractor are a bit tired. Depress the clutch or turn off the machine with an implement raised, and it will...

Can I burn kerosene in my ford 8n?:confused: mixed with gas or by it self to save gas and money With gas being so high :mad: Thanks phil

I am new to this forum, and I just bought a Ford 8N, it has the 12V conversion but it wasn't and is currently not running. I have checked the spark, its good and blue-white. I figured it was then...

Well... It never fails.You talk something up, it will break!! :D The steering went out on my 8N this morning while I was hogging. The steering wheel is screwing right out of the tube that goes...

I recently went to the barn and found my 8Ns coil and wiring burnt up. Though a little strange, I figured I must have left the switch on and battery connected for this to occur. Anyway, my dad...

See video.... I am having trouble starting the Ford 8N. It has been very reliable and then stopped working.... While trying to start it, the starter made a weird noise and as it started to turn...

I just bought a Dearborn 19-42 loader (jungle gym type) and was wondering if anyone has one or one like it on their Ford N-series. Mine looks to be strong and heavy. I never had a loader on my 2N...

Need to install a new distributor. The old one had been removed. Any how-to's out there?

I need a starter for my 1950 8N. Mine just crapped out on me. It spins freely but 12V @ 2amps wont spin it 12V @ 40amps barely spins it and 12v @ 200amps spins but gets really hot.

Hi all, I am new to this forum and need some help. I have a Ford 8n, side distributor, 6V system that will not crank. I do not have a clue what it wrong with, but assume it is the timing. I have...

Not sure what year the tractor is , maybe 1930s ford 8n?Anyway, Im trying to locate part name/ number for the bushing that connects pitman arm to steering rod/link. Please see attached picture...

Hi guys, I am new to the forum and tractor world! I recently purchased a well kept 1950 Ford 8N with side mount dist. and converted to 12V. The previous owner, just prior to selling, had a...

I have been trying to get my 8n working by replacing carb, new distributor, plugs etc. Will start, run for a few minutes then die. Started this morning. It immediately went to max rpm, backed off...

I bought this cultivator and the guy said it was 3 point. Once I got it home, I am scratching my head wondering how to hook it up. I feel stupid! ;-)

I just bought a ford 8n tractor with a monroe moldboard single bottom plow. When I try to plow the second furrow the plow leaves a plow width between dead furrows. How can I adjust the plow so it...

hi i have a 48 ford 8n tractor and i was out plowing snow with it and i went to lift up the blade and it went up then dropped and now it wont raise anymore. I took the blade off and i still cant...

Joined TractorByNet today to keep an eye out for useful tips on refurbishing our newly acquired Ford 8N, serial number 308681. This will be a three generation project; Grandpa (my father-in-law)...

PTO on my Ford 8n won't stay engaged.The engaging lever pops out and PTO disengages.How do I repair this problem.It's a 1952 8n.Thank you in advance for your replies. Ken

ok here it goes. A couple of days ago I was plowing the snow with my old 8n and all of a sudden it stopped running. I founb that the sedimate bowl had fallen off. I looked everywhere and couldnt...

I purchase a Ford 8N some time ago. I removed the 6v battery without noticing the way the battery was hooked up. Do you hook the red cable that comes from the stater/solenoid to the positive...

On a '47 8N I am having a no start issue and I think it has to do with the carb. When I removed the air intake pipe which is between the air cleaner and the carb there was fuel spilling out of...

I've got a 1952 Ford 8N that I could use some help with. The tractor has been in service on our farm since the early 90s, and has basically always worked flawlessly. Last year, we bought our...

I went to another consignment auction yesterday. spotted a nice restored 8N Ford up for sale.

I have a little Ford 8N. I was out discing a small patch for planting a garden. When I finished, I brought the tractor back to the house and went to shut the fuel off at the sediment bowl...

We got hit with a rain storm in between snow storms this winter and there is a layer of ice under everything. While this was happening, I was asked to help manage a horse bording operation. We...

I have a 50' 8N with a dirt blade on the front. After 40+ years of pushing snow and leveling dirt the steering has become very tough to turn. Is there any adjustment I should try or is it...

What is the correct setting for each of the 3 valves on an 8N (1952 model). A couple weeks ago, I took the carb apart to put in a new float and messed around with the valve settings. Just got it...

Well, i went out to build another chicken pen today, as the wife is getting some silkies she doesn't want mixed with the rest of the heinz-57 chickens we have .. so i loaded up all my tools and...

First of I would like to say hi to everybody me being new and all !! I have a question. I have a next door neighbor that has sold me some land last fall witch is great . Now I had plenty of room...

Need a starter solenoid for a 1952 FORD 8N. Sits on top of starter and is 6 volt. This is for My uncle who has macular degeneratin. He hooked wires up backwards and fried the solenoid. Any help...

My brother gave me a nice new Holland sickle bar mower.. Wonder if my Ford 8N will work ? I want to get it set up ..and simply leave the mower on it. I have two other modern tractors. I could...

I have a 1952 Ford 8-n tractor with a positive ground. When ideling the tractor puffs white smoke, while under load the smoke goes away, why?

I am looking at attachments for a Ford 8n. What I am doing is cleaning up a 1 acre lot. What I need to do is move some dirt, cut in a drive way, and maintain the growth. The implements I'm...

Thinking about trading my 1990 Miata for a 1952 8N Ford with new paint and new tires in mint condition.... What is the going price for the 8N?

Hi All, So I have an 1952 8N that is driving me crazy .... Even though the tractor has a push button start near the gear shift lever (like "normal" 8Ns , the previous owner wired in a more...

As some of you know I purchased a 1951 Ford 8N at an auction recently and so far I couldn't be happier with the purchase. But I do have one question. At idle or slightly above the exhaust makes a...

In the picture above, what are the two pipes? They aren't on my other 8N. By looking at them, there is one that leads down to the hydraulic pump. The other is in the cover..... Right where you...

When I bought my tractor it had a janky upright exhaust and flapper that hangs open. I want to replace the exhaust with a factory style exhaust. I looked and TSC has the exhaust for a good price...

been helping a friend to bring his 8N back to live after years of just sitting in the yard(The tractor , not me)Got it converted to 12volts,electronic ignition and installed a new radiator,greased...

Just changed the oil on my 8n tractor. When I removed the drain plug, I noticed that the screen was not above the drain hole. Upon further inspection the screen, housing and tube were just laying...

I am a new homesteader, and a first-time tractor owner, on 40 acres in the Ozarks. I recently bought a rebuilt Ford. I think it is built from several tractors. The front half has serial numbers...

Hello, new here. i am having fits with an 8N Tractor i just got in a trade. The man brought it to me and showed me how well it started and ran. So, next day i went to start it and i think i...

I am about to takle replacing the clutch on my 1952 for 8n tractor. I nver done this before on a tractor, I have replace the clutch on my car and I am somewhat mechanic savy. Am I getting over my...

I have a 8n with a front mound distributor and 12 v. I just jot is and it ran fine worked up 1/4 or a acre went to use it a week later the battery was dead so i busted it it did not start right...

I get and install a new starter last week, life seams like it's getting good. I changed the plugs out today, messed with the thing a bit and it wouldn't start after it had fire up about 20 times...

I have a carburetor from a Ford 8N. I purchased a rebuild kit and disassembled the carburetor. After cleaning it up, I went to reassemble it and am having some issues. I have all of the old parts...

Howdy all! So I bought tractor about 6 months ago, ran pretty good. I am a serious novice at this but trying to learn. Was moving brush one day and tractor died. Started right back up, parked...

Hi all, I currently own a 1952 ford 8n. I went on vacation for a week and came back and it would not start at all. It ran well prior to my week of freedom. Pulled the hood, found a crap radiator...

I am knew to tractoring and just got my hands on an old 8N. It has 28" rear tires and I am in need of chains for plowing this winter. Does anybody have any suggestions as to which type of chain to...

I think any 3 point hitch will fit any other. AM I wrong? John bjon79@live.com

Does anyone happen to know a NAPA part number for the exhaust (what we used to call) donut gasket? :confused:

What oil and oil filter to use on my 1948 Ford 8N?? I live in WI, doesn't get used much in the winter. primarily used for brush hogging and light driveway grading. Any help would be greatly...

I am looking at a 1952 ford 8n gas to buy as my first tractor mainly for field mowing and setting fence post. The tractor is in good condition orig paint comes with brush hog, rear blade, post...

I'm looking for the original styled pto shaft cover for the 1 1/8" pto that the 9n / 2n / 8n / NAA-Jubilee came with. I've seen the modern repro's that are for the larger 1 3/8" shafts.. but was...

Have 8n ford that I bought last year and it ran good until I parked it for the winter. Started fine this spring until I tried plowing. Made one round and it quit so started checking and found a...

It will start, run for a few moments, then cut out. It will start right back up, but same thing...runs for a few moments then dies. I have checked through the fuel line, and that seems to be all...

Hi Guys I have a 1950 8 N that the 3 point hitch dosen't work right. We have replaced the hydraulic pump, upper cylinder, piston ,rings,and all gaskets and the arm that goes thru the big spring...

I'm considering turning the rear wheels on my ford 8n tractor to get a wider wheelbase. But I am concerned that it will not fit on my trailer after that my trailer is 6'10" wide. Has anyone done...

Restoring a 50 8N rims and center disc are bad need used parts to replace

Attached are some photos of toolbar I built for my 8N. With the hipper/hiller attachments: With the cultivator attachments (just a test fit so didn't take off the hipper/hiller): The...

I am trying to help my uncle with his 1952 Ford 8N. It will run as long as you are spraying starting-fluid into the carburetor. He has rebuilt the carburetor, and that did not help. He took the...

I'm shopping for a rotary tiller for my 1950 Ford 8N tractor. What size will work best? What would be the best one for my tractor? Thank you, Rick230

I am working through some starting issues on my 8N. It is a side mount, and i have put new points (set to .025), and a new condenser on it. I am now thinking maybe something is wrong with the...

I think I have a problem I have a Ford 8N I drained the rear fluids replaced them with GL1. now the lift does not move at all. It is in gear and looking through the inspection port fluid is...

I inherited a nice 8N. I have a pro 5' wide mower attached that I mow the pasture with. I wasn't thinking clearly i guess when I bought a new DR 3 pt. hitch PTO Trimmer to do all my fence...

Hello everyone. I was directed to this net by surfing Google looking for tips on replacing my 49 8N Fords rusted out fuel tank which I have started doing yesterday. I got the hood off, which was...

I got a Ford 8n few months back with a supposedly rebuilt engine within a year before I got it. I didn’t notice it had no oil pressure at the gauge until I had already brought it home. I did the...

Ford 8n was running about a month ago and I drove it for about half an hour. Now it won't start at all. Took apart carb and cleaned it and everything looks fine but still won't start. Lots of...

I recently purchased a 1951 8n The hudraulic lift will not work. There is no apparent or unusal noise in the system, all other functions are in order, Where do I start? I want to do the work...

I need to get a back blade for my old Ford 8N. Do you think a 7' blade is too big for an 8N to handle? I'm thinking about buying a Land Pride Back Blade...

Hi folks, my father in law passed away around 6 months ago and my brother in law took over the place. It came with an old 8N that was converted to 12v a bunch of years ago. It runs good and until...

I inherited my dad's 8N this year, and one of the last things he asked me to do was get the tractor fixed up and take care of it. I told him I would, so I checked all the fluids and put a new...

Okay, I've never seen this before. I went and looked at an 8N yesterday with a backhoe on it. I expected a homemade job. But it's not. It looks like it is factory installed right on the back of...

This just started when i went back to mowing pasture. I set throttle at about 75% to mow but it keeps kicking it back to idle even if I don't have a load on the mower.

What multi-grade engine oil would you use in an 8N Ford tractor that would be good for all year usage? I'm thinking maybe Rotella or Delo 400 in 15W-40. What think y'all? This tractor doesn't...

Who do you use for good quality parts for Ford 8N's? Thanks, BridgeBoy

Hello, I have one of the early years Ford 8N, before there was adjustment in the steering box. Does anyone know how to correct the issue of horrible wobbly steering. 3rd gear is pretty much...

How involved is this? The hydraulics are getting real weak, struggles to lift my 4ft bushhog. I have good basic mechanical skills and basic hand tools, some air tools.

Hi everyone- I have an 8n (52 or 53) and the PTO developed a pretty good leak pretty much out of the blue. So I've read some posts and it sounds like a few guys just had material wrapped inside...

Good evening. I will be parking my 1952 8N Ford at an off-site location for some time and would like to replace the fuel cap with a locking type for security reasons. If known, please identify a...

Mods feel free to move if this is the wrong forum. 1951 Ford 8N tractor with Dearborn grader attachment. Low hours. Runs & operates ex. Only 42 known to exist.

Hey I'm a new member 8n ford

My 8n has a steering problem, new style steering box, when I turn the wheel the steering shaft moves up and down as much as an inch. Could this be as simple as bearings, or do I have bigger...

which way does the" open"side of a pto oil seal face ,this is the replacement rubber seal thanks

Hello Everyone, About two years ago my family and I quit the rat race, bought 40 acres in Mark Twain National Forest, and began to homestead. We now have chickens, guineas, dairy goats, and...

I am getting ready to rebuild my 1951 Ford 8n. Any ideas on the best way to remove the cylinder sleeves?

I have a 1952 8n that I've been using for the past 3 months. Besides some carb issues that were an easy fix, it's been Damm near turn key everytime. Today while I was mowing I started hearing the...

I have had my tractor for about 2 years. Just recently it started burning lots of oil. When the cutting season ended I took the head off. Lots and lots of carbon. I removed the side plates and...

hey all I have a 1948 Ford 8n that has weak spark so far apart that have been put on it is a new coil new points new condenser new wires and a new ignition on off switch problem is I can't get...

Yesterday I attempted to raise my brush hog to adjust the cutting depth chains. Hog went up; won't come down. Then engine stopped and now will not start. I took the PTO shaft off thinking that...

Just purchased a 1952 8n, and the mechanic said several things wrong, overfilling with hydraulics being one of them. He said he needed to "break the tractor apart and split" right below the...

I bought an 8N 1950 Ford tractor that has been changed from a 6 volt to a 12 and the man said it just quit on him. When he checked the distributor shaft wasn't turning. We pulled it to see if it...

I am having trouble with the hydralic lift i can get it to raise up but it will not go back down. I need to know how to fix it

So going threw old post the common conclusion is either dirt in the needle valve or a float that is stuck or needs adjusting NEW carb and both the screen in the carb and fuel filter are good. Now...

I have a 8n ford. When I last used it it was fine. I went to start it the other day and it will not turn over. I have checked the battery it is well charged. The thing does not seem to be getting...

The steering on my Ford 8N will steer to the left fine but it locks up when I try to turn it to the right. It finally went out all together and I replaced the top and bottom bearings on the...

I just bought a month ago a 47 Ford 8n tractor. There is teeth broke off of the flyweel so I ordred a new one and took the engine out tonight to change it. Everything went fine until I tried to...

have been trying to get the starter out of my '48 ford 8N tractor but get hung up on the flywheel. Any suggestions :confused2:

arm kind of new to this I have a 1948 Ford 8n that has week fire and or no fire so far I've replaced the coil points condenser wires and I had put a new resistor on it before I install new coil...

I just rebuild the carb and it dies on acceleration. I have no idea what's going on. I have new fuel, clean lines and it can't get up to 2000 rpm, separate from the gov even. I've adjusted all...

Couldn't find anything in the search, but here is my dilema. I happen to have a complete 1949 Ford Custom Deluxe 4-Door sedan. I haven't had any luck selling it (complete car) and have been toying...

Hi, I'm Nick. I have about five acres to mow and a football field size garden. My John Deere 110 is struggling (great tractor, just too small!), thinking of getting a Ford 8N (or 9n) with bigger...

I have a Ford 8N which is stubbornly refusing to start. When pressing the start button, I hear a click in the starter motor but nothing else. Not sure where to go from here. Anybody got...

Hi Friends, when we ended some time ago, I primed the pump like advised via that relief valve and had good pressure quite promptly. I replaced a few plug wires and the tractor faithfully started...

I recently bought an 8N that appears to be a 1949 based on SN. I disassembled the right front hub to check the excessive play and found both bearings to have been completely disintegrated. Thought...

Local mechanic made service call to replace spark plugs, plug wires, and install Pertronix Ignitor 1244AP6 on our Ford 8N, 6V positive ground with side mount distributor. After installation and a...

Hi everyone, my dad has a ford 8n (12 volt conversion) that stopped running about 2 years ago and I cant get it running. I dont have details on how it was running before it stopped. It cranks over...

My dad purchased 8n afew months ago,issues started there. First experience with tractor even though somewhat knowledgable with automotives. Tractor would start run about a minute then shut off...

I'm a big believer in RTFM. I'm a new 8n owner ('51) and to avoid asking a million repetitive questions, what book(s) should I invest in getting? I though I had heard a suggestion of the I&T FO-4...

When attaching the impliment power shaft (Mower, etc)to the pto, there seems to be a pin that moves in and out, can you explain the operation of this ? Also is there a small entrance hole on the...

I have a 1949( I know the title says 1948) 8N with the old style steering box.Not having the funds to purchase a newer type box,I rebuilt the old one. After rebuild I can turn the steering ONE...

Can you tell me what type of and how much hydraulic fluid I should use on my Ford 8N tractor? I believe it's around a 1952 model. Also, while checking the fluid my son dropped a very small soft...

I just recently purchased an 8N Ford tractor with a 5' mower. Brought it home, change the fluids throughout, sharpened the blades on the mower and went to our land and cut 3 foot tall grass/weeds...

Background: 1952 8N I bought it and the clutch was like a toggle switch 1/2 inch from down to full clutch engagement. The adjustment clevis was at it's limit. I thought it needed a new clutch...

dear box contaminated with water .Did not know this until I went to use one single degree morning and pto was engaged and tractor was difficult to turn over.Lift won't work pto o.k..Question is...

I inherited my grandfathers tractor and has been sitting a long while . I took it apart and put new valve train in it and had the head rewored . I got it back about 2 weeks ago. The next step was...

Hey all, I知 new here as a registered member but have browsed the forums on and off for some time. Still not 100% certain this is the right place to post this question, but hoping those on here...

How much could I expect to pay for an old Ford 8n in pretty good shape with bush hog ? Thanks

Just bought my first 8n, not ana ctive farmer just like 8n

Hi, all. I've been a lurker here for many many years - finally signed up (read the whole flail mower thread last year). I currently own a New Holland TC25D for maintenance of 2 acres, plus...

how to set - advance - timing on frt dist ford 8N ?

On an 8n with a front mount distributor, is changing the fan belt as simple as loosening the generator bracket, slipping off the old belt, and then slipping on the new belt? Or do you have to...

I have a 1950 Ford 8N Tractor. I've ordered a new in the box fuel assembly. I have two questions: 1: When I remove the old fuel assembly from the tank, I wanted to put something on the threads...

Ok. I decided to finally start messing with the 47 8n that has been sitting in my grandma's garage for the past 15 years. I'm 20, and i have mediocre mechanical knowledge, but the old tractor is...

I believe this site will be most informative about my Ford 1720 8N Tractor:laughing::laughing:

on a 8N tractor, just aquired, there is a lever, just behind the Hydraulic control lever, also a slotted (Filler ) just to the right of the lever, these are unknown to me, can you identify and...

same as th title.

I am trying to help my uncle with his 1952 Ford 8N. It will run as long as you are spraying starting-fluid into the carburetor. He has rebuilt the carburetor, and that did not help. He took the...

Bought this 48 Ford 8N about 22 years ago to grade a private road I lived on. We moved to a larger parcel of land, 6.17 acres with 380’ of high bank riverfront. At first I used it to run a 6’...

it think clutch went in my 8n . i would like to know is there a way i can see if it is the clutch or a gear in the transmission that went? i was using the tractor, then it made a noise and quite...

Good Day All: I am trying to rebuild the hydraulics on my 1948 8n. As I live in Alberta, Canada, and as I do not want to pay as much for shipping the parts as the cost of the parts, are there...

Does any one know how to fix the brakes from leaking fluid from the rear end onto the pads I have replaced the seals pads the gaskets and still have the same problem. I might have them for a lil...

Picked up an old 8n recently for next to nothing. The guy suggested it probably needed a tank cleaning. It also had an inline fuel filter I wanted to remove and get back to proper fuel lines. I...

I have a 1950 Ford 8N tractor that will not start. When I try all I get is a "click" from the starter cylenoid. I have checked the ground and made sure I have a clean, tight connection. The...

What multi-grade engine oil would you use in an 8N Ford tractor that would be good for all year usage? I'm thinking maybe Rotella or Delo 400 in 15W-40. What think y'all? This tractor doesn't...

Greetings all! I've just joined TBN to listen, learn and hopefully one day contribute as new discoveries come my way.

I'm rebuilding a steering box for my 52 8N, unfortunately I have to replace the steering shaft (the steering wheel was welded to the shaft). The new shaft (right) I received is quite different...

Trying to get son-in-laws 8N front distributer, 6volt pos ground to start. He replaced plugs, points, cap and rotor, but I think he turned the distributer! What is the best way to get...

Hi all, I have had my 1952 Ford 8N for about 10 months now and have used it for everything. Over the summer, I went on vacation for a week and came back to a tractor that wouldn't start. I have...

Greetings all. My 8n steerig is very tight and hard to turn. Does anyone have any suggestions?? I tried to loosten the adjusters, but the inner screw only turns about 1/2 turn. Im not sure if...

I noticed the fuel bowl has a very slow drip. I tightened up both lines on the valve but drips still form. I saw a couple on ebay for $14.24 and $13.20 with free shipping. One of them states the...

I was using my Ford 8N to cut the field. It quit. I checked for fire and didn't get any. I checked the coil wire connection through the distributor and found that it was shorted. I fixed that...

The 3 point on my 8N will come up without a load, but will not lift with a load. I weigh 170# and it will not raise one bit if I stand on the lift arms. Would you please give me some...

Hello All: Need your infinite wisdom regarding my Ford 1948 8n. The hydraulics on my tractor are a bit tired. Depress the clutch or turn off the machine with an implement raised, and it will...

No loader or attachments, rear wheels @ normal width? I,m buying one from my father but won't bring it home until I have something built to keep it out of the weather. Thank you.

Anyone see this yet? Try this website MBtractor.com the 8N new holland retro tractor.coobie

I have a 1950 Ford 8N. The three point hitch seems to have some problems. First off, I have changed the oil several times, but it becomes whitish like it has bubbles or something within a very...

Our family has an 8N and we recently acquired a Ford 501 sickle bar mower (14-339). The mower has a 1-3/8" 6-spline PTO shaft, while the 8N has a standard 1" 6-spline shaft. We found an adapter...