john deere

Can anyone help with model of this planter

I bought this 3pt hitch lift type MX10 cutter brand new. Used very little. Low hours. Approximately 2200lbs going off memory ? Works great. Always kept inside out of sun & weather. I went up to batwing & zero mower. $8900 pick up in North Georgia No trades Call Mike six78 98six...

Good evening everyone, new guy here. I recently bought a JD 2350 with a 245 loader. It has a quick-attach bucket, but not like the hook and pin QA I am used to. Mine has two square vertical spring loaded pins that lock the bucket in place. Attachments for this style seem pretty hard to find, and...

A 2016 John Deere 1025R with Powerflow Material Collection System! $15,000 less than new! At 247 hours, this 1025R is powered by the 23.8hp Yanmar 3TNV80 diesel, 3-cylinder, liquid-cooled engine with a 2-range hydrostatic transmission. Equipped with the 120R loader and JDQA bucket, and the 60″...

I recently purchased an 850 with factory dual remotes. I'm a large person and the levers hit my leg. Additionally, both valve bodies are leaking. I want to delete the remotes completely. I only run a mower and have other machines with loader. I've found the replacement "cap" that has no ports...

I am trying to determine the proper rear ballast for my 5055E. I have a 520M loader that has a max lift of over 3k lbs. I want to lift at least a ton and trying to determine rear ballast. The manual for the loader shows two options for a cab tractor and one option for OOS. I have an OOS. The...

Here is a PDF for how I did it. I hope it helps you.

I was stationed overseas for 4 years, meanwhile a handy man hired to maintain my property back in the states, blew the engine in my JD 4610. When I returned home I found it completely disassembled and I'm trying to put it all back together. There are a few points I'm stuck on, as I can't...

Started well run like crazy than died tried restarting with a little gas in the air breather started well than tried a little diesel in the air breather and bum an explosion what damage could it have caused .

Stated it and it run like crazy for 3 min than died

Hi, just joined and first post. I have a 25 acre property, some steep slopes and mostly forested. I'm wanting to buy a new smallish tractor with 4 in 1 bucket to do the following: Moving rocks and soil Pulling cut down trees out for firewood and lifting them into stacks Grading/maintaining...

Good running John Deere 70 Tractor with wide front end. No hour meter, so hours are unknown I have video of it running, if interested

Ive been reading here and on the internet that some owners turn up their hydraulic pressure on their 2520s been thinking about doing that any of you owners had done this? I check mine and its 2475psi thinking about going to 2700 will I break something or blow seals out with 200 more psi thanks

Does anybody know how much a complete set of 19.5-24 & 12.5/80-18 New R4 tires & wheels would cost from JD ?

I'm looking for comments and thoughts for the John Deere Frontier RB2284 Rear Blade. I have a 72" Land Pride and I'm thinking of going to a wider and heavier blade. This is much heavier than my current blade and I don't have rear hydraulics. Is this too heavy to adjust without hydraulics? My...

Anyone have any idea when this was built and what it is worth? I know in most case with serial numbers 001 would be the first one built? The story is it was bought new with this 1953 John Deere 40.

My 1445 has 1725 hrs and the deck will not stay float . It has a danfoss hydraulic control valve . I am not sure if or how to adjust the detent to keep the deck in float

Back story on tractor is I did a rebuild on it new pistons, rings, rod bearings and head gasket. Flushed radiator new thermostat adjusted valves. I got it back together and it will start but it just seems like it has no power and I’m pretty sure it’s getting to hot also it won’t idle has to be...

Two questions: I have a commercial-grade JD Zero Turn mower that I use to mow my rural property. It was purchased in 2012 and has 870hrs on the clock. It is serviced regularly and is in excellent shape. The dealer says that it is time to replace it because JD is discounting the 2023 models, and...

I have a 1986 John Deere 650 tractor. it is currently stuck in 4x4, the shifting handle just free wheels like its not hooked to anything. the roll pin in the handle is good. Can I pull the shaft that the handle is mounted on? I am assuming that the shaft it broken or what ever it was driving...

The tractor has been sitting all winter, and now it won't turn over. The solenoid gives a loud clunk, but that is all I get. No hint of a starter problem before this. The battery is good at 12.7V at the starter. Tried shorting across the posts on the starter, and got nothing, so I'm thinking the...

Need some help in figuring out why my front loader will work, however not at strongly and will lower without contant monitoring, while 3 point will not go up or down....changed filter, not leaking hydralic fluid....any suggestions? Thank you, JMS

Hello All, I have recently bought a 1966 John Deere 4020, got a screaming deal on it. I am hoping to find a loader for it. I have seen that John Deere Loaders 48/148/158 do fit and work. I was able to find a few 'fairly local' but the asking price is higher than I paid for the tractor. I am...

I started a rebuild on my little 850(yanmar 2500). Back story is it got hot the other day and seemed to have blew the head gasket , so I dove into the motor and found what looked like a bad head gasket, small groove in middle cylinder wall and the connecting rod bearing in pieces all on the...

I started a rebuild on my little 850. Back story is it got hot the other day and seemed to have blew the head gasket , so I dove into the motor and found what looked like a bad head gasket, small groove in middle cylinder wall and the connecting rod bearing in pieces all on the middle cylinder...

Bought a 301A over a year ago that had been setting along time turns out all I needed to get it started was a new fuel transfer pump and rebuild the starter ….... everything seemed to work well except the rear lift arms wouldn't hold a middle position no biggie ran for a bit but I noticed was...

Quite simple to replace the seals.

Probably not the most apples to apples comparison but I have been looking at new tractors for a couple of years now and getting closer to pulling that trigger. I have looked at and drove most fo the current brands out there. LS was far from my list of tractors when this started. However, there...

I just recently bought a John Deere 850 for a super cheap price compared to what the market is in my area. Everything seems to work as it should and it seems pretty clean. The only issue I’m having with it is it seems to have a slight miss to it around 2,000rpm not sure what it could be I’m...

I purchased a 5520, the instrument cluster is not working. I sent it to be tested and it works fine. I've had a mechanic work on it extensively with no success. The cluster has rpm, fuel gauge and temperature gauge. I'm considering just adding aftermarket fuel and temperature gauges. I'd love...

After a few months of owning a 5055E tractor, I finally got to remove my 405 backhoe to attach a box blade. I've been swapping the front attachments and during that, I tend to lose oil like most of the owners. It's been bothering me but since it's a new tractor, I didn't worry too much. After...

I currently have a John Deere 5020. The radiator is busted and can’t find one anywhere. It runs and drives. None of the gauges work besides the hour meter. It has 4800 hours. Hydraulics and pto work. Was wondering about a price I should sell it for. It has brand new front tires and 2 of the...

Just purchased a JD 2040 It has a front end loader on it and I would like to convert it to skid steer compatible: There are two pins on each side to remove the bucket. At first i was intending on grinding and welding a receiving plate on the tractor and the other part on the tractor, but...

The TYM T25 (RK25) is a good tractor that I bought in 2021. Was afraid to buy an older tractor because I really didn't want to deal with older problems, but I have been looking at others such as the Kioti, Branson 25-26 HP tractors. They weigh more, have more lift, without the EPA baggage. I was...

Hi all, I have this really nice LX172 been serving me quite well for the last year or so. Shifting became quite hard as of late and ended up with the shifter breaking at the link point. Welded it back together and still having issues with the shifter being very stiff. Any ideas would be highly...

Ok gents…here goes. I have a 2022 Woods 84” Rear Discharge Mower TKP84.40 (TurfKeeper Pro), and despite my trying the gearbox keeps getting water in it. I know it’s water because the gearbox oil is milky. It was recently replaced, as was the o-ring for the vented dipstick. I first noticed the...

Hi all, does anyone have the correct resistance number for the clutch solenoid RE177539. having issues, but want to make sure before I buy a new one. thanks in advance paul

Hello, knowledgeable and internet-friendly folks! I hope you're having a great day so far. I've come across this particular machine and while going through John Deere reviews, I've heard that they can be quite challenging to repair and come with high costs, intentionally imposed by the company...

I’m preparing for the winter months and looking at snowblowers. Anyone have experience with the Land Pride SBP16 series or John Deere Frontier SB1174P?

hey guys, im new here. hopefully I came to the right place to find some help. I just bought. used 2011 1600 series 2 with 2600 hours. hours didn't really bother me as the machine didn't look beat up and id only be using it 5-6 hours a week, 6 months out of the year. I used it Monday for the...

Following my earlier note regarding play (a lot!) in the rear splined section of the driveshaft, I've bitten the bullet and gone ahead and extended the shaft by 18mm. The rear yoke is now fully engaged on the input shaft of the transaxle - in fact, the shaft extends into the yoke itself by about...

working on installing rear remotes on a john deere 301 a, hoping to use a generic aftermarket set up to save on cost. main issue is knowing where to plumb into the tractors hydraulics to go to the valve body. any info on how to find which ports to use would be greatly appreciated thanks

i have a john deere 301 a tractor that when trying to engage the rear pto depressing the clutch does not disengage the pto drive and it doesn't allow you to flip the pto lever to the on position. pushing the lever forward only causes it to grind gears, the clutch works fine for the transmission...

The output shaft on my MX6 rotary cutter broke and is stuck in the stump jumper attachment. When I look at the manual/part diagram, it appears that I should be able to drive the broken shaft with a sledge back out towards the broken side. I have not been able to do so. The cutter is about 9...

Buy an Ultimate Rack Combo and Save $300! Our best selling Ultimate Rack Combos just got better! Order a combo and enter code: QH2023 at checkout to save $300 off your order, we'll even throw in a free 5n1 Tool Holder! That's over $500 in savings when you include free shipping ORDER HERE .

Seeing the post this morning about the decline of the new tractor market made me think. What is the expected deprecation of used tractors? How much per year or per hour can you expect your equipment to lose in sale value on the used market? I'm sure it matters if you are picking up a JD or...

Annnd I am back... Ok got some strange things afoot with the 2440...When the PTO is disengaged, center lever down, I am having hydraulic issues. The Power steering will only work intermittently with High RPM's, and the rock shaft will do the same it may or may not go up with the higher RPMS...

Hoping for some advice and opinions on selecting a tractor. Have about 240 acres that has been pretty woefully neglected over several years. Want to get it whipped up into better shape over the next three years. Regrade and maintain approximately 5 miles of dirt/gravel roads on the property...

Anyone have any suggestions as to what may be causing the lug nuts in the front wheels of my John Deere 855 to loosen up? I did the 500 hour service about 4 years ago, about 1 year before the problem started. When I changed the transaxle oil I was not aware of the breather plug on top of each...

John Deere 5101E - Power Reverser indicator came on and immediately stoped pulling like it is in neutral. Any advice what to look for?

Does anyone know if any Ford 1710 tractor engine parts are interchangeable with a John Deere or even a Kubota, and if so what models of John Deere or Kubota tractor are compatible with a Ford 1710 . I know the tractor was made in Japan and I believe the John Deere was also. I was curious if that...

Does anyone know if any Ford 1710 tractor engine parts are interchangeable with a John Deere or even a Kubota, and if so what models of John Deere or Kubota tractor are compatible with a Ford 1710 . I know the tractor was made in Japan and I believe the John Deere was also. I was curious if that...

We almost never have any discounts/coupons/sales, but heeeere we go! www.EverythingAttachments.com Travis

My 1996 JD 770 tractor is not starting. i get no lights or anything. checke battery-it's good. i checked the fuses and after pulling them all-it did start. then, a few days later the same exact thing happened. i quickly tried the check the fuses again and this time it didn't help. any...

Hi all, I have a John Deere 6430 premium tractor with loader and electronic joystick w/paddle and electronic SCV controls. I am having lots of trouble with the loader and SCV’s. I get errors on the screen for SCV I, SCV II, ICV I, ICV II, ICV III. It is always a Sic 34 error with the...

Hello. I have a JD750 20HP compact tractor that just got back from getting the engine overhauled. Engine runs great and blow by is gone. Loader and 3point work fine. I was using it this morning to move some dirt to cover some holes in my drive. Went back and forth from dirt pile to driveway a...

Hello, I have 1970s JD 7300 Industrial Tractor with all the original manuals. The Repair manual is held together with two weird flathead screws and I'm looking to get a binder to put it in. However, the hole spacing is not uniform (the middle space is bigger than the top and bottom spaces...

I'm buying a new tractor and it's between the TYM T474 ($35k new) and John Deere 4044 ($52k new). They are similar in specs, but about $17k price difference. Obviously JD has better brand, more dealers, and sounds like when I talk to folks, a better tractor. I'm trying to warrant spending...

Top Link with Rear remote install. Full post of installation of the Summit kit. Should work for most any tractor that has a power beyond port, such as for a backhoe.

Hey everyone, First off the battery box and dash need some dusting. I'm trying my hand at electrical. The original switch was jumped to a toggle instead of ignition by the previous owner. I have a wiring diagram and a new A&I main ignition switch. The back of the replacement has numbering that...

Without buying oil at 2x the price at a dealer, what do most of you use for your small JD diesel tractors? I have a 2305 and an x745 mower. Yanmar 24HP engines (as I recall). We live in Missouri, summer mowing can be in the 90's, and the tractors get little use after November, so I don't worry...

I recently broke one of the crappy original plastic pistons in my loader joystick and figured I could buy the parts and fix it myself. It didn't seem too complicated but there is one thing that seems to not add up. The replacement piston part (R230282) is structurally different than the...

Leaking from rear diff jd 790 see pic arrow points to hole been leaking for nearly a year when i load in trailer i notice most. Dump trailer steep incline. The stick reads half full its came down from the top of full over about 8 months since last fluid change. I assume its overflow leakage but...

I am looking for where to buy aftermarket parts to rebuild the reverser in my John Deere 410B. There is a company in Louisiana that rebuilds them for $4300, ouch!! Naturally they dont offer a kit nor will they say where they get there parts from. I have read on some forums that these...

Our John Deere E110 mower caught fire last Saturday. Still don’t know the reason why. It started in the front near the exhaust. But it didn’t have any electrical issues or gas leaks. It was the first time we mowed my daughters backyard. It wasn’t that big a yard 60x45 feet. The grass wasn’t that...

I got this Tractor as a barn find only 85 hours. It hasn’t been turned on in years. When I go to turn it on all it does is crank. I emptied all the fuel out of it and replaced it with new. Still does the same thing. All the fluids are full. I pulled off the injector lines and they had fuel but...

Hello all you fellow rural and JD geniuses! I have an interesting problem, but I do not know where to start exactly. This just started happening yesterday - We have a Katolight generator that surges terribly on a cold-start, for up to a good minute or so until it warms up or load is applied. It...

I’m trying to figure out what’s wrong with my pto it’s a John Deere 4105 and pto will engage and disengage as is supposed to but doesn’t have enough power to turn a brush hog and if I hook it up to a auger it spins it but as soon as I put pressure down it will stop moving

Hi All first post! I have a JD 1600 (non turbo) wide area mower and after about 30 minutes of use it overheats and looses all the coolant. Fan seems to run fine, any tips on what to look for? I’m going to try a rad flush and blowing the rad through with compressed air but it looks clean. I...

I have a JD Compact 990 MFWD with a box blade and loader. I wanted to use it on a steep dirt "driveway". A fwd pickup can navigate, but not sure about the tractor. My tires are not in the best shape. So a question to you more experienced operators... will the tractor go up this appx 30% slope OK ?

Hi I bought a older JD 850 2 wheel drive and I have a question regarding the PTO. Is it normal while tilling or bush hogging to hear a click noise when you engage the clutch while using the attachment? is it some sort of slip clutch built into the tractor. it is a fast click not a grind or a...