Search results

International 500

It's a Dexstar rim

My 532 has instructions when you lift that hood on the front(decal) Lots of manuals on Ebay too.

There are 2 rims on Ebay , look for 16x11 Tractor rim.

Southern farm equipment on EBAY -$48.95 free shipping ! 4mm bolts

You cut the wire with the flat plug that goes from the key to the starter solenoid.From the key goes to the terminal where I attached the rubber plug. The cut wire with the flat plug goes on the right terminal of the ford solenoid.You could drill a couple of holes and mount the solenoid to the...

Can you figure this out? The starter wire from the key(that goes to bottom of starter solenoid) is cut and attached to small terminal(I just had that rubber terminal). Big post on left is for battery power off of starter.Big post on right goes back down to starter solenoid. There is 2 bolt holes...

jdparts.deere.com

Go to Hoye Tractor Parts and look under YM336 (hydraulics) and you will find the adapters you were looking for. You can also google- HA-38 hydraulic adapter and find it , or HHA-18 hydraulic adapter for the kit so you can just use hose.

Make sure the thermostart isn't leaking fuel into the manifold.

The whole thing is only $ 81+ tax on Ebay .

If it has it,it's under the left of dash,the later models don't have compression relief.

Just pull the compression relief and bump it over. If there is no resistance,then crank it .

No ,I went to google and only TBN had the breach.

Just got a message from Google that TBN had a Data Breach , and had to change my Password.Anyone else?

Google AM102452

Go back to Hoye and look again-under engine rebuild(336). It doesn't use a nylon gasket,uses an o-ring. oil plug-HDP-112 o-ring ***-112

Just google - Washer AW(NTN) and click on the Misumi site Or Look for Misumi bearing lock nuts They have both and in 10-50 mm+ .They have the measurements,so you can match up the size you need.

What store had this cheap veggy sale ? Haven't seen 5 for a dollar in 15 years.

What model generator head is that ? Is it 1800 RPM ?

If it has a canopy,the turn signals are up there,and it will have a turn signal switch on the left side of dash.

Use the threaded hole back behind the starter

This is from the 1050 operators manual.

JD950/1050 -same axle Yanmar put a vent in,just left of the center(little J tube)

: :)

It looks good,hope they put a bucket over the muffler ! I would buy it if it was closer .

Google it,and you can download this . I had a 66,that had the short hump like your pictures.

I have the turf tires on mine.I have a set of the lug tires too,never got around to using them.They are under the house on the hill,that fell down!

Looks like you had a good one this time.

This one ,on Tractor House? in Milford NH

From Cook's Saw

This was on my cousins game cam.Young buck taking a selfie. Surprise!!!

Here are some pictures of the one on my YM186D-should be similar?

Google the part number-R57270 greenfarmparts.com shows they have them John Deere does list them on jdparts.deere.com and they don't say NLA ,so a dealer should be able to get one too.$246+

This is the "Rack" on the pump. It has a flat lever attached to the pin,with a little bushing and a hair pin. The rack is probably stuck? It should move freely in and out of the pump. Take off the breather cover above the pump and you can see it and maybe free it up.Or you might have linkage...

Both of mine have turnbuckles with a hole drilled through one rod,inside the turnbuckle,and a simple hair pin stuck in keeps the turnbuckle from unscrewing.They came that way from the factory.

Been raining for a month!

Those 2 wires come from the stator(Generator) that is under the flywheel.They put out AC ,not DC You have to connect them to one of these Rectifier/Regulators to get DC to charge the battery,and you have to have a battery connected to power the coil.

Some pictures that show the ball slots in the coupler and ball grooves in the shafts.

Texas Horse

#1 in picture Power comes from key switch,when turned left.

Cat Burglar

This is what you need.

Just Google -how to wire up a ford solenoid. This is probably close enough (ignor the chevy starter)

flying squirrel

Mar 18, 2014 10:27 AM Man Charged In 2012 Murder Pleads Guilty A man charged with killing another man in what police call a botched drug deal has pleaded guilty in the case. James Simons pleaded guilty to manslaughter, robbery, assault, and tampering with physical evidence in the 2012 killing...

Here's my homemade sawmill,made out of a house trailer frame and scrap for about $500. Then I built a 28x26 shed over it.Then I built a 24x36 metal building,and the only lumber I bought were treated boards along the bottom.Takes alot of time when you do it all by yourself,but costs very little.

Here are a couple of pictures of the crank out of my MF31. The keyway cracked,and the threads stripped.

Never seen one before,until yesterday.Two things I picked up had fat juicy widows under them with egg sacks.One in the woods and one in my shop! Anyone else seeing them where they never were before?