ford 1700

Hi All! Noticed I had a headlight out. I rebuilt my grill over a decade ago, and I remembered the bezel was held on by an odd spring clip. I managed to pop the bezel off, but can’t figure out how to get it all back together again. Anyone have access to instructions? Thanks!

Hi All! First off, forgive my long-winded ramble. Just trying to give as much info as I can. I went out to do my pre-snowstorm check on the Ford 1700, and discovered the battery was dead. It started immediately with a jump, but is not charging. I also noticed the headlights wouldn’t work...

I need help sourcing cylinder seals to rebuild all 3 boom cylinders, Can't find replacement seals online. Any suggestions are appreciated.

Hello. Have a Ford 1700. Not in any way, shape or form a mechanic but thanks to this forum have kept it going 15 years now. Have a new issue which has me stumped. Unable to start tractor. It sits outside and I try to start it once a month at least. Went a little longer than usual and now it...

Hi! I have an old Ford 1700. Recently, the control arm for the 3pt lift has been "slipping" up. Messing around with it, it goes down with resistance, but when I pull on it, it moves pretty easily, which means if you hit a bump, it will lift the 3pt arms, which makes grading really annoying...

Hello, Hello, i have you ever ran across s 1979 ford 1700 will not move and stalls when clutch is released, I was connecting to an when I tried to take off, the tractor would not move. When I let off the clutch, the engine stalled and died. No repairs have been previously made, just it's been...

Hey guys, first post. I've been googling and searching this for months and I'm still at a loss, so finally decided to just pose the question outright and see what folks more knowledgeable/experienced than me have for suggestions. Basically I have the two tractors mentioned, and need to get rid...

And how did the snow get in there, you ask??? Well, because I'm a STOOPID - that's how. Battery was dead so I went to change it - took air/oil filter vent stack off to open hood ....... and never went back. 15" dump and just realizing I didn't put that vent cover back on. How screwed am I...

Hey guys, So I did create a post about this before. At that time I did not have all information. So there is a neighbor that lives nearby that said he may be interested in selling his Ford 1700. So the tractor has about 2,300 hours on it and he has about ten implements with it. It is also not...

Anyone know of a steering assist kit or power steering kit for a 1700? I’m aware of the Jackson but $1900 is a hard pill to swallow. My new box that I got from kumar bros last 4 months and broke.

Was out doing my normal brush hogging, all going fine/normal, when I went over a section of raise up dirt that bogged down the machine. I assumed it was just a small mound and after restarting without PTO engaged that I'd drive forward to smooth ground and continue --- but machine is 100%...

I recently picked up a 1980 Ford 1700 2wd with nearly 3300 hours to mess around with. The sound of the 2-cyl diesel is unique! It seem to run and shift fine. Some questions: 1. The turnbuckles on the 3pt hitch arms have seen better days. Is there an aftermarket telescoping stabilizer arm that...

the radiator screen on my 1980 Ford 1700 is rotten and trying to pry the metal frame a part to just replace the screen is not working. I have found a couple of complete screens on line but at 120 bucks I am thinking I can build something, now I have an idea but I'm looking for something that has...

I've just inherited a 1980 Ford 1700 4WD and I have a couple of issues that I'm hoping someone can help me with. This one is about the diff lock. I just noticed that the lever for engaging the diff lock is stuck down. I think I've ascertained that the diff lock itself is not engaged, because...

I've just inherited a 1980 Ford 1700 4WD and I have a couple of issues that I'm hoping someone can help me with. The first is the cooling system. It seemed to be fine when I was plowing snow, but yesterday (warmer weather), I had it running and the temp gauge went all the way up. I wanted to...

Anyone have experience with replacing rubber mounts/spacers for the step plates; or have suggestions on alternatives to secure the step plates. Will appreciate any thoughts.

Can anyone tell me the difference between a Ford 758 758a 758b and 758c backhoes attachments. Thanks

Hey guys, So this community has been awesome so far and things are getting more complicated. As some of you may know my neighbor just gifted me an old 2WD Ford 1210 and I am deciding what to do with it. Well my neighbor just got gifted a Ford 1700 that he is not sure that he wants. He has at...

Hi, Very inexperienced old tractor owner. Trying to get the rim off the center piece of the rear wheel to replace it. I am not familiar with the kind of nuts holding the piece on. I know it's a castle nut and I have to try to remove the cotter pin but what is the piece of metal folded around...

Ford 1700 tractor stopped I drained gas put new cleaned glow plugs turns over won't start notice no smoke not coming out of stack at all...can ya help me out.

I managed to bust the sump casing assembly (SBA322010100) on the front drive axle, which led to cascading failures within. Found replacements for the casing and bearings, but the drive pinion (SBA322050230) is all chewed up and I can't find one for sale. I should probably replace the driven...

Good morning. I got a new safety switch in last week, but went away for a long weekend. I opened up the trans cover this AM, and I believe I knocked a spring in the tranny well. Going to try and get it out with magnet pick up tools. If I don't get it out, will it ruin something if it is...

Seemingly overnight, my awesome 1700: Had a harder time than normal starting Actually seemed to 'catch' and run okay, but, just wouldn't get it's idle or rpms up It surged for a minute or two and then ultimately ran ...okay. I've got the brush hog on but not slogging through anything crazy or...

Hi everyone I have a ford 1700 that I use in comerical service for my sawmilling and custom farming operation. Recently while brush cutting I noticed that the pto shaft had some in/ out play, shortly after that the pto shaft was on the ground still attached to the brush hog. From looking at the...

Crossing over from my starter/ignition getting sorted out, tracing wires and finding loose ends. I'm at the fuse block and finding some things that I'd like to make sure they get plugged in correctly (at least one). As I understand top down, we have rows 1 - 4, left and right. I am looking...

Hi All, I have a 1979 Ford 1700 4wd. Was bush-hogging and tractor began to lose power and eventually stopped. I was low on diesel and may have run out, but not sure. I did refill, but when i turn the key i have no lights, no action on the starter. Battery is 12.8 v. Last year i had a similar...

Hi All, I have a 1979 Ford 1700 4wd. Was bush-hogging and tractor began to lose power and eventually stopped. I was low on diesel and may have run out, but not sure. I did refill, but when i turn the key i have no lights, no action on the starter. Battery is 12.8 v. Last year i had a...

Hi. New to site. Had to replAce a shift spring. Drained fluid,inspected gears ok. Replaced all spring’s and balls and fluid. Gears shift without clutch. When startedruns great hydraulics work and pro work, when in gear no power? Any suggestions would really be welcomed. Thanks

I have owned my Ford 1700 since 1972. Today the check engine light came on for the first time. (not the battery light). The engine oil is full. Any ideas on what the problem might be? I realize it could be a bad sensor.

I bought a Ford 1700 with around 850 hours about ten years ago. About four years ago the water pump went out on me. I replaced it and decided to do a top to bottom service on it. I found that the hydraulic fluid was very sludgy and looked like some moisture had gotten in it. I pulled the...

I have a Ford 1700 Farm tractor 4X4 that I bought to repair and use. The previous owner told me the clutch went out on the tractor. I started looking for anything else that could be the problem. I checked the hydraulic fluid and it was empty. When I brought the tractor home I cranked it and...

I have a 1980 Ford 1700 tractor. I just acquired a 3 Point Hitch Tractor Supply Log Splitter. On my tractor if you are facing it from the back, on the right hand side under the seat, there is a small block with a hydraulic hose coming out the top and a lever on the front (like by the seat). I...

Hey everyone. I have an 1981 ford 1700 that is very hard to start. At -2 degree celcius it can take me about an hour of cranking to start. With 2 magnetic block heater and the in line pipe heater. Im new with diesel, but have relatively very good mechanical skills. Heres what i know Glow plugs...

I have a 1980 Ford 1700. I am having a hard time locating a rear rim. 10x24. Is there any type of interchangeable rim ( single piece) or combination with center that is easier to find. I live near Cincinnati

I hope someone can help! I have a ford 1700 2cylinder diesel tractor that has sat up nearly 10 years. After installing a new battery and freed up a cam inside the injector pump, I was able to get her running. She would move but no hydraulics. I checked the fluid and it was milky gray. Drained...

Hi, Had a question. I have an old Ford 1700 tractor. I let it set for a year after the battery died. Been trying to get it started. Found out the starter was shot. Replaced it. After putting the new starter in when I turn the key there is a clunk, the fan blades move a couple inches and...

Is there a spec for the head bolt that goes into the block on the 1700. I know the nuts get torqued to 107 lbs but what about the bolts into the head.

Hopefully finishing up a rebuild on my ford 1700. All timing marks are right on. Had fuel injector rebuilt also. Before l put the head on l wanted to see when the fuel is injected to the cylinder.While turning the crank l could see fuel popping out of the pump fittings where the fuel line is...

Hi all! I'm considering a local 1985 Ford 1700 w/ loader and augur and 1300 hours as a first tractor for my 10 acre plot that needs some light clearing and maintenance. I'm just completely lost on what reasonable pricing is these days - any inputs? Thanks a million!

I was changing the headlight bulb in my 79 1700 ford. The retaining clips fell out. How does it go back together? Anyone have a diagram ?

Continuing my big "tune up" maintenance, and today is oil change day, but not finding this oil filter noted above. A regional tractor parts shop says there's a New Holland number (but they didn't want to give out the number and for $38 (shipped) I thought I'd see if anyone here knows where I...

Hi all, I'm about to replace many of the hydro hoses on my Ford 1700 and, especially on the shorter ones, am noticing that when I try to loosen the securing threads ...the hose resists mightily; getting all coiled and kinked. This may not be that big a deal when taking off the old, as they're...

Well its been a long road with this tractor, through many glow plugs, a rebuilt fuel injector pump, rebuilt injectors, fixed crack in head and reground valves, motor taken out and rebuilt and new clutch installed. Just starting to see the light at the end of the tunnel. After setting the lash...

How do you get the bulb out of the headlight on a Ford 1700? the headlights are kinda fragile. The I can twist the bulb and feel it click, but it doesn't come out. Do you have to take the front chrome trim ring off from around the glass and get it out the front side? I didn't want to try too...

So this happened out in the field the other day after I turned the tractor off to brush of the radiator. When I went to get back on, the tractor wouldn't start. Didn't even try to crank, but lights came on. Had the tractor in neutral, clutch depressed as far as it would go. After doing some...

Some may remember me talking about my neighbors tractor that belonged to her father and I had tried to buy, well back in Dec 2020 she decided to take me up on my 2 year old offer and sale it to me. I changed all the fluids and filters and with a little work got that old tractor to running. I...

Hello all. I've got a Ford 1700 with no lift on the 3pt hitch. My grandfather bought it new and I've used it for the last 20 years and has been a great tractor. Anyway, It went from working completely fine one day to a little jittery and then completely stopped working the next. I believe I've...

So after mowing for about 4 hours this weekend, my 1700 began to develop a 3point problem. The 3-pt was no longer holding up the bush hog. If I fiddled with the controls a bit, it would lift up the bush hog and then drop it back again. If I let it try to hold the cutter up then it will...

I need a rim for a Ford 1700 in Southern Michigan

Looking for a rim for a Ford 1700, 1977 in Southern Michigan . It is a six lug on the center piece, and 4 bolt from rim to center piece, has 12.4 - 24 turf tire on it now.

Anyone here ever had their (3pt) lift control spool valve apart? After replacing my 3pt lift cylinder seal and then redoing the seals in the hydraulic pump to no avail, the only place left to turn was the lift control. Just for reference the 3pt had worked although it would leak down. I was...

I am looking for a couple of front axle parts for my Ford 1700 4wd. New or used Coupler: SBA398380020 joint Assy. SBA326240240 drive pinion Please reply if you might know where I can purchase these items..... Thanks, Jay

Replacing the seal on my 3pt cylinder piston, old one came off in pieces. Noticed the piston head that moves in the cylinder has a couple deep scores in it. Before the seal entirely failed the 3pt worked, just drifted down after a while. I’m thinking it’s not worth messing with the scoring given...

Hi Everyone, I recently purchased my first tractor, a Ford 1700 with about 2100 hours. The engine oil looked very dirty so I decided to go through and do all the maintenance items assuming the tractor has been a bit neglected. The first thing I did was purchase a manual which has been...

I am helping a friend of mine get a Ford 1700 he recently purchased up and running. Its a 2 cylinder diesel, the previous owners bypassed the fuel filter (it's missing the filter cup and element) and had the fuel line directly plugged into the injection pump. Some background, the tractor cranks...

Good afternoon, had my head sent out to be welded due to cracks around the combustion chamber. looked real nice when I got it back . I installed it with the service manual so it should be right. Also added two new exhaust valves because the old ones were badly pitted. Had all valves reground...

Installed new head due to cracks, installed in cold temp,just my luck. The install went great, got the motor warmed up with a torpedo heater. Started up for about 30 seconds and stopped, let it sit a a bit and tried again. Ran a lot longer after it warmed up but seemed to lose power. I let it...

Looks like my head gasket is leaking before the thermostat opens. After it opens the lead stops. How hard a repair is this for an average person? I just replaced the water pump, the thermostat and both radiator hoses, now this. Another 2020 year problem.

Hi All, First, I'm a complete diesel tractor noob, but I'm handy! This tractor hasn't been in use for 5-6 years. I've drained the gas, changed the oil, new glow plugs, new battery and drained the radiator(all according to the specs found here). I had to replace the upper and lower radiator...

I've read the other posts on this topic. I changed the seals on the piston and tried adjusting the position control link. The pump makes hydraulic pressure. When I move the lever for the auxiliary rear hydraulics, fluid shoots 20 feet out of a hole in the line. When I move the lift control lever...

Hi All! So, New tractor, replaced the clutch, got the loader back on and hooked up the battery backwards (oops!). Let the smoke out of the alternator, so bought a new one. Replaced the mechanical regulator for a solid state one, and replaced the battery for kicks all at the same time. The...

I am looking for a couple of front axle parts for my Ford 1700 4wd, used would be nice! SBA398380020 Joint Assembly SBA326240240 Drive Pinion Could you please let me know if you know of anyone who may have these items available used. Thanks!

Any problem with using rubber fuel line to replace the leak off line between the two injectors? If I replace this line, will I have to bleed the system? Will appreciate any information. JLW

looked at all of the threads i could find on the hydraulics, very informative. another lift problem i am afraid. usually the lifts on all my tractors have blocked screens. not this time. so after a lot of reading i am looking into the lift arm/cylinder area. my question is this, the cylinder is...

I had to remove my injector pump to send away to rebuild. While the pump was away the tractor was moved and the engine was turned over. I re-installed the pump but now the engine will not start. Does anybody have the procedure for timing this engine? Adding to my confusion is the manuel says the...

Trying to tinker with a 1980 Ford 1700 I'm looking to pick up from a friend. Replaced the starter solenoid and got it turning over. Fluids and all that changed already, injector pump oil as well. Bled the fuel system, seem to have solid fuel spurting at the block with injector lines cracked...

I am looking at a Ford 1700 that has a FEL, structurally everything seems solid although most of the paint is gone but it looks like a Ford 770. The loader needs hooked up and the lines need replaced from the 2 lever control valve to the loader. Fittings are fairly rusted at the control valve...

Looking at a Ford 1700 that a friend is selling. It was his father-in-laws, he is helping his mother in law clean the place up and get rid of stuff. Engine is free, needs a bit of wiring redone, going to mess with starter and see if I can jump the solenoid after reading some posts here. Oil...

Inside the pressure relief valve on my ford 1700, what all parts are supposed to be in there? Specifically, is the little cone shaped piece on the end of the spring supposed to seat in something besides just the housing. It seems like it wouldn't seat tight against the housing and that's all I...

Can anybody tell me what type of hydraulic fluid my Ford 1700 takes? I see some that says its compatible to 10w30, and some "Ford tractor hydraulic/ transmission fluid" that says its 90w.

I found out that I need a new rebuilt engine does anyone know of a company that has reasonable prices for rebuilt engines? The crankshaft is bad.

Hi Again! Planning on the clutch split this weekend, and figured I'd redo all the oil while I'm at it. I picked up 2.5gal 14w30 Rotella T4 (I THINK that will work?) And I have 5 gal of Napa aw46 hydraulic oil. Just wanted to make sure those will both work in this thing =) In another thread...

I have checked the injector pump and can see that the throttle is moving freely but it does not move the cams in the injector pump. I have taken the side cover off and can see the spring looks ok but not sure of what the throttle lever is going to move to make the cam rotate to allow fuel to flow?

Hi All! I was running my 1983 Ford 1700 the other day, when I heard a crashing noise. I shut the tractor off immediately, and discovered the Crankshaft pulley had lost it's retaining bolt, and fallen off. Since the fan belt tension kept the pulley in place, and I have no reason to...

Good morning l sure hope everyone is doing well, l own a Ford 1700 that takes 15w40 shell Rotella, that's what the previous owner did also. Would it hurt to use Shell 10w30 synthetic blend instead just to help with starting in cooler weather. Tractor haS about 3000 hrs but was rebuilt with 2000 hrs

sorry for the double post. I posted this in the hydraulics forum with no response. Figured I'd try here. First let me say that this is my brothers tractor. I borrow it from time to time to mow our (mine and his)hunting property. I'm working on it because I'm more motivated to get it done and I...

First let me say that this is my brothers tractor. I borrow it from time to time to mow our (mine and his)hunting property. I'm working on it because I'm more motivated to get it done and I need it in a month. Last time I went to borrow it, we couldn't get the hydrolics to work. Searching on...

Any easy way to check injection pump timing on the ford 1700. Found some good info on here but can anyone explain how to open up a thumbnails to see the picture on this site

Hello, getting cooped up at home and making work for myself. Decide to do some p.ms on the Ford 1700. Anyone know what is a good compression number for the cylinders. I tested them and they are at 390 psi. Reason being l get a little anti freeze coming out at times in the overflow when the...

Hello, since we are stuck at home trying not to catch the coronavirus decided to do some pm work on the 1700. In the process had to remove the hydraulic pump to get at the fuel injector pump. Now once everything is put back together cant get the hydraulics to operate at all. I do have a manual...

Hello, l own a Ford 1700 tractor, nice tractor but its eating glow plugs. I get about 4 uses out of them and they burned out. All electrical is good and ignition switch checks out. Would there be a possibility of something inside the head that's worn l am using l believe the correct plugs...

Use tractor and starting to notice when going up a very slight upgrade or pushing snow tractor tires crawl to a stop in 2and3rd gear. I dont notice the engine working harder. This tractor was like a tank before. Would push alot of snow and not stop. Is the clutch going bad or slipping. Any way...

I bought my ford 1700 last year. I'm starting to think the battery is undersized. Its the size of a car battery but the battery stand is way bigger. Seems when l use the glow plugs at first it weakens the battery were it doesn't crank very fast. Does anyone have an idea of what size battery l...

Hello From snowy Green bay. Having issues with glow plugs burning out after a couple of starts. I did some looking around and l have about 9to10 volts going to the plugs when turning the key to the left. The indicator glows red. Question 1. Is it ok to leave a battery charger on the battery when...

Hi All, I'm a little confused as to what type of oil to put in my machine. Reading owners manual shows 10w30, 10w40 for year round use OR 10W for severe cold below 32, 20W for winter use between 32 to 50F and 30W for summer above 50. Then an internet search came back with a bunch of C-rated...

Hello. First time post, Starting to have an issue with my Ford 1700 starting. Temp is 60 degrees out. Engine cranks over good and have exaust coming from the stack when Turning it over but don't start. Tried glow plugs and still don't start. Plug in the block heater for 2 hours and it starts...

Anyone have a problem with tractor not turning over. New starter, solenoid, and battery. When trying to turn over the solenoid smokes as well as the positive battery terminal? Anyone have this issue? Im going to back track all the wires to make sure there are no bare ones. Thanks

Similar models per the FO-44 manual, may include 1100, 1110, 1200, 1210, 1300, 1310, 1500, 1510, 1700, 1710, 1900, 1910, 2110. I have a Ford 1700 with a power steering option by duBro, a California company, and a FEL. The FEL has a dedicated but optional hydraulic pump that is causing me some...

My first post y'all, hopefully I manage to do it correctly. I've got a Ford 1700 with a 2 cylinder diesel, firing order 2-1, with 2 marks on the pulley, the first for injection timing, the second for TDC (information all gleaned from this site, thanks for that). While running the FEL I...

I have a 2wd 1700 with rear diamond tread tires (13.6-16), and I would like to get increased traction when pulling, plowing, and similar. I have no steep inclines/declines, but the ground is quite wet and sometimes muddy/silty. This is Florida, so no snow here. I don't really have much of a...

My Ford 1700 is equipped with remote port but will only operate when the 3 point is raised. I need to be able to operate the 3 point and the remote separately. I have debated between installing a pto pump and reservoir or an interrupt of the high pressure hydraulic line to supply the remote...

Hi All- I have a 4WD Ford 1700 that I need to replace the clutch on. This is my first time doing a clutch split on a tractor. I have the I and T manual and followed all the steps and have all the bolts/nuts removed to split the housing. The manual does not address the driveshaft for the 4WD-...

I managed to grind up the steering shaft and ball nut assembly on my Ford 1700. Anyone parting one out who would be willing to get me either these two internal parts, or if more convenient, the entire steering gearbox assembly? Thanks! Jan

My hydraulic pump quit and I got the rebuild kit from NH. I put some witness marks so it goes together the same. Everything looks worn. I'm not sure how it goes back together as the plastic pieces on mine are worn. Also I didn't undo the nut as I'm not sure if I need more witness marks. Anyone...

My hydraulic pump quit and I got the rebuild kit from NH. I put some witness marks so it goes together the same. Everything looks worn. Im not sure how it goes back together as the plastic pieces on mine are worn. Also i didnt undo the nut as im not sure if i need more witness marks. Anyone...

i need a front rim for my tractor mine was broken and reweld an its not straight

I have 1700 Ford with black oil coming out one of the exhaust ports, no smoke, changed valve seals, still coming out. I read on the forum before I became a member. someone had this same problem, but the member never posted if the problem got solved.I think the members title started with an A. It...

I just got my 1700 back together and now it boges down when I go in to the top gear of the trans and when I us the pro and hit a big clump of grass is it the injector or injection pump

I replaced my shifter assembly due to a broken shifter. The knob broke off. When I removed the assembly the detent springs fell out and I didn't realize it until later. I bought 4 new springs and the drawings on messicks showed 4 of the exact same springs. I drained the fluid and found...

I've got a Ford 1700 that drains the battery when it sits. (I've actually got two Ford 1700's, one is for parts. The wiring is similar between the two, so I can compare the wiring and/or swap parts.) I'm at least a little bit familiar with electrics. The drain is no secret, when I connect...

Hi All, Lately I have been very busy at work and constantly traveling and very little time to check the forum. Just saw several PMs that I did not see early enough to respond. Sorry for the late reply. Several people asked for my lift cylinder work and the pictures. I will go ahead and upload...

I have just recently purchased a 1979 Ford 1700 tractor with 1680 hours . It's in good condition but I want to service it before using it this summer for bush hogging etc. My question for you guys is can the fuel injection pump be serviced ? If so how ? What kind of pump does it have ? Thanks...

I have just recently purchased a 1979 Ford 1700 tractor with 1680 hours . It's in good condition but I want to service it before using it this summer for bush hogging etc. My question for you guys is can the fuel injection pump be serviced ? If so how ? What kind of pump does it have ? Thanks...

Hi all, My great ol' 1983 Ford 1700 is telling me I should be in the market for a new Hydro control "lever" setup. I have the "2 lever" control today (boom - up/down, bucket - roll up/down) and it's the 'bucket' control that basically ...won't turn off. I've setup a bungie cord at this point...

The mounting bracket where the FEL attaches to the body of the trailer (New Holland (19SW1814) - FORD LOADER 15 & 17 TRACTOR (1/79-12/84) Parts Diagrams - see part 6 in the diagram) is cracked near the bolt hole on both ends. I don't have a welder nor do I know how to weld - and I'm unsure...

I have a Compact Ford 1700 4x4 needing new rear tires. It came with 4 ply AG tires. I had them filled with fluid and the rims are badly rusted. Need suggestions about ply ratings for replacement. Should I buy 4 ply again or 6 or 8 ply as replacements? My main use is for snow clearing...

i was wondering do i have to buy a used block cause mine broke the bottom of the skirt out on one side

Hi, I am in need of some advice about where to purchase pieces for the voltage regulator/help identifying what I need. I am new to being in charge of caring for a fleet of tractors. We have a Ford 1700 that had some electrical issues this year and I ended up replacing the wire that goes from...

Anyone have a reliable source for an aftermarket muffler for a Ford 1700(North American). OEM ones are over $300.00

was wondering if a backhoe from a ford 1300 would fit on the 1700 ford for sure. under the attachments on tractor specs it lists the 757 on the 1300 ford and the 757 and 758 for the 1700 ford the only thing I was wondering was if anyone knows if I would need a different subframe mount to switch...

i ran out of hydraulics on my 3 pt lift system,i don't remember what brand to use what would be the best hydraulic oil to put back into the 3 pt system tank,i looked at the old manual it says 5.3 gal,but it don't say what to use,could anybody help,,,thanks

need some help finding parts for my ford 1700 i need a block, crankshaft, and one rod or i just need a short block

Hello, I just bought a Ford 1700 4wd, with a loader. After getting it home and running it for awhile I noticed a leak from the power steering cylinder. I have been looking for information to fix it or rebuild it. I have a DuBro aftermarket hydraulic steering cylinder. Does anyone know where...

Okay guys here we go again, posted a while back about my son's 1939 Ford 9N that he inherited and turned out it has a cracked block. I was telling my neighbor about it and they have a 1980 Ford 1700 that I have ran before but has not run in over five years and I did try to buy it several times...

I purchased a 1978 Ford 1700 tractor 4wd. I need a radiator cap for it. I found plenty of caps for ford tractors but I could not locate one for the 1700. I don't even know what PSi cap to purchase, there is nothing in the manual I down loaded indicating cap pressure let alone Cap part number...

Greetings JC, I have a Ford 1700. The tractor has 560 hours and has been sitting for the past 10 years. I bought it at an estate auction. The hydraulics worked very sporadically. I drained the hydraulic oil twice, cleaned the screen twice, vacuumed inside the opening where the screen is located...

Greeting Forum members. I have a Ford 1700 tractor that has been sitting for approx. 10 years or so. 550 hours on meter. It starts up nicely and is very dependable. The hydraulics on the other hand has been my issue. The hydraulics was very sporadic in the beginning. I drained the hydraulic...

Hi Folks, Just bought my first tractor ! Bucket list thing :) I live in upstate New York, just North of Albany by about 15 miles. Originally from the UK from 20 years back. Could never of had a tractor there. Surburbanite. Mine needs a lot of TLC and came with a FEL. I like to restore things, so...

I have a ford 1700 with 1300 hours on it. I changed the oil the other day and started the engine to fill the filter then shut it off to check level and when I pulled the dip stick I heard a rush of air(pressure being released). I've never heard that before so I'm wondering what could be...

My 1700 3pt will not raise I'm assuming it's the pump we already took the screen out and cleaned it and put new fluid and that didn't help when it's cold out it'll work some when the oil is thick but once it warms up you get nothing. My question is where is the pump located and how hard is it to...

HELLO, I am starting another thread on this because the old link seems to be a dead end. Does anyone have a source for the 1700 axle fix?? (machine shop new) I saw a listing on Ebay a couple months ago but that is no longer there. Any help would be great. The $1500 total kit from a New Holland...

I am looking for left and possibly right lower kingpins for my 1980 Ford 1700 4wd tractor. I believe these are the correct part numbers: SBA330300471 kingpin L/H lower SBA330300491 kingpin R/H lower The lower left side kingpin is worn the most. I have a front end loader on my tractor...

I have a Ag-Tech AT-720 FEL for 1982 Ford 1700 and I'm trying to rebuild the lift and bucket hydraulic cylinders. I took the cylinders to a local hydraulic shop and they noticed that one of the bucket cylinders was slightly bent. The hydraulic shop tried straightening the bent shaft but...

Team Looking at a local Ford 1700 for some small work I have to do on my place. Currently has turf tires in the front. Can I swap out ag rims and tires or is there actually a differant hub / bolt pattern ? Thanks

Have a 1700 4x4 with loader, and one of the front (badly weather-checked) tires gave out this past weekend. Was surprised to see they are only 4 ply rated around 750 lbs load. Am hoping to replace them with something not quite so aggressive as they tear up the lawn pretty bad being narrow...

Does anyone know where I can find a manual steering gearbox that will fit my ford 1700 (Japanese model)? I bought one several months back that I believe came off of some other type of compact tractor and it only lasted a month before the balls came out of worm gear. I bought the kit to replace...

Where is the best place to get good deal on loader bucked assembly for Ford 1700 tractor? Have looked locally (Sarasota Fl) area, to no avail. Any ideas much appreciated. Ron

I am looking for a couple of front axle parts for my Ford 1700 4wd CUT. New or used Coupler: SBA398380020 joint Assy. SBA326240240 drive pinion Please reply if you might know where I can purchase these items..... TIA Ted

Thought I would toss this out in hopes one of you can see what I am overlooking. I installed a 10 micron hydraulic filter on my tractor and it proceeded to blow the filters within doing 6 lifts with the front end loader. The schematic attached for the Prince SV valve is exactly the system that I...

I had recently looked at a new Kubota and liked the additional step offered on newer tractors. My knees aren't what they used to be, so I added the step below to my 1700. I put it at 13" vs 20"of the height of the main foot deck. Obviously it changes the ground clearance, but not an issue for my...

I was going to replace the springs on the shift levers, so was looking at the parts diagram below from Messicks. I noticed the part #47 shown as a seal. I've had hydraulic fluid issues with this tractor so figured what the heck, I'd do those at the same time. So I was surprised that when I took...

I am seriously considering using a power beyond valve on my tractor so that the front end loader and the three-point can be used at the same time. My loader is using the accessory port under the seat for its hydraulic power and return. In order to use the power beyond valve I need a hose to be...

Greetings gentlemen, My pastor bought a used Ford 1700 or 1710 tractor (I'm not sure which model exactly) about three years ago. This past summer he started having issues with his 3 point hitch: it would raise very, very slowly and in a jerky or incremental fashion. I don't really have much...

I worked on this about five years ago, have a leak, and can't remember the details unfortunately. I have a basic question for anyone familiar with the adjusting components. ITT shop manual says that the box should be filled with 134 transmission fluid, and filled up to the opening plug. Fine. My...

I have a ford 1700 tractor 770 front end loader. My controls for the loader started acting up so I looked into getting mine rebuilt or buying a new one. From past experience buying parts for my tractor..... they are crazy expensive and probably not available any more....grrrr I was shopping in...

I thought of selling my Ford 1700 for no other reason than accessibility. With size 14 boots and a gut to match, it is not the easiest thing to get in and out of. It has plenty of horsepower for what I need and I've got a few 5 FT wide implements which she handles without issue. I've got her in...

Ford 1700 4wd manual steering, 770 front end loader Does anyone know of any places that sells a steering gearbox rebuild kit and / or sells an already rebuilt gearbox? Also looking for left side shifter. Mine is worn where it goes onto the slides inside the transmission and sticks in gear...

Hello All, I am considering purchasing a Ford 1700 that is listed for $3,000 obro. I don't know a lot about it yet but wanted to see what the general feeling was concerning price. It is 4wd but the seller states that there is an issue with the 4wd, not sure yet what that entails and I know...

I know im new and yes ive searched for my exact problem and haven't had any luck. so ive hard my tractor for prolly a year now and its became very hard to start within the past 6 months even when its hot outside. I have fuel, hot batt, and glow plug indicator glows red but will only start with a...

I am the 2nd owner of this tractor for the past 20 years and have been able to do my own repairs(starter,water pump, fuel system etc.) Now this steering system is leaking and I assume it is aftermarket and I don't have a clue how to identify it. The only plate on the back side says F1700 and a...

WONT RAISE DISC OR LIFTS WHEN IT FEELS LIKE IT. NEED TO KNOW WHERE FILTER IS AND HOW TO RE PLACE IT?THANKS ANY HELPS IS APPRECIATED

Hi there, I just picked up a Ford 1700 not sure what year (79-82?) 4x4 with duall 155 front loader. I also found a good by on a Land Pride 1248 rotary cutter and 48" Henry j rotavator. I'm hoping to use it to keep brush and weeds down around the property and till up the garden and arena. From...

Having some problems, 3 point that will raise and lower but when it is stopped I hear the relief valve. no matter where its stopped. After a short while 5 min. or less it is real bad and just wont move at all but them out of the blue where it raises and them lowers. when this is happening the...

Hello fellow tractor folks! Im looking for help locating the seal for my PTO. Does anyone know where to purchase this? Also what oil to refill with. Thank you in advance.

I am trying to change the oil in my Ford 1700 fuel injector pump, but can't remove the fill plug/breather cap to pour in the oil. The cap does not screw off--it just spins when I twist it. I tried lifting it up, then twisting it, but it still just spins. I also tried to gently pry it off with...

Greetings all! Long time guest reader, first, well, second time poster. I have been reading about Ford 1700's in various capacities over the last 8+ months. My wife and I have built our dream home on ten acres, and needed a tractor to help with mowing the upper and lower pasture once we moved...

I'm getting ready to fab up a subframe for my Ford 1700 / LW-6 backhoe. Thinking about 2x2 or 2x3 tubing with 5/16 wall. Seen some where it was flat plate but tubing might weld better. Thanks! Brian

I've got a adapter block on my 1700 that I have hooked to a backhoe. Well I drug home a front loader and need another circuit. I was hoping to be able to 'stack' the adapter blocks to have two somewhat separate circuits. Not sure of the fluid paths but two bores flow thru but one is plugged and...

My 79 1700's loader is working very very slowly and only if I give it a little gas. So far I cleaned hydraulic filter and changed fluid, replaced the seals in the hydraulic pump and checked the relief valve on the 3pt. The 3pt is working great right now. When I pull the 3pt all the way up and...

I have a 1700 tractor that has evidence of having a front loader installed at one time. I just picked up a LW-6 backhoe and I was thinking about tapping into the 1700 hydraulics. But exactly where??? Thumbnail pics are Side view, Rear view and Front. The center block is a loop that previous...

How much weight can I carry on the back end / 3 point on my 1700 4wd? I would like to get a small backhoe attachment but I'm concerned about the weight. Brian

Hello Forum, I bought a Ford 1700 tractor with 550 hours on the meter. It has been sitting for around 10 years per sellers family. The engine started up fairly easy and runs great. The problem I have is that the hydraulics work maybe for the first 5 minutes then stops. The front end loader...

Howdy, Just picked up a 1700(4WD) and it needs front tires. I have ag tires on my 1600(2WD) and the wife won't left me go any where off the dirt. So the 1700 with turfs should allow me more access. The only tires I have come across so far are the "Carlisle Multi Trac CS Lawn & Garden Tire -...

Hello Everyone I am another new guy, with all kinds of questions. I have posted a short intro in the introduction forum for those who are interested. I own a 1983 Ford 1700 tractor for the past 25 years or so. I use it mainly for work around our backyard farm, and plowing snow in my very...

Has anyone tried using automotive tires for the front tires on the Ford 1700 tractor? If so, what size tire/rim, any modifications necessary?

Happy Thanksgiving! While plowing the 15" of snow that fell in New England last night, the Ford 1700 died quickly with no notice and no load. I thought it may be fuel, but after review, that was fine. Some quick history, in the past month the glow plug indicator, glow plugs, battery, and the 770...

First time buyer & found a Ford 1700 with roll over gannon box, loader, & the 757 back hoe attachment that he says works but needs some attention, not sure of the year or the hours just yet as I still need to take a look at it. He's asking $7000.00 would this be a good price for this tractor ?

Had this thing for about 4 years. I has taken a little work but I've kept it running till now. When I turn the key I get a little rotation on the motor ~30 to 60 degrees or less. I've charged the battery, jumped it with the car, replaced the starter. No joy with any of these. I've even...

Well I had my first experience with a stuck clutch. I had my tractor over at my mothers doing a little work and I had to leave it outside uncovered. It rained and was a week later before I got back to finish. When I started it up the clutch was stuck and would not release. I had a middle...

I'm a novice. I was trying to hook up a three point backhoe to which I've extended the lines 10 feet to help get it into position. I'm standing there and hear the sound of the tractor change. I look around and find one of the extension hoses has fallen off. Things seem jerky on the backhoe so...

I have a Ford 1700 and I cleaned the filter changed the fluid. 3pt does not work at all no movement or anything. Pulled the cylinder out and turned tractor over and all the fluid empties back into the diff bypassing the cylinder all together. Guess my question would be what would cause this so...

I recently picked up a Ford 1700 which had been sitting. New fluids and a hot battery fired it right up. The older gentleman I bought it from told me they hydraulic lift worked fine until his son changed a rear axle which was bent then they never worked again. Just out of curiosity where should...

The water pump went out on my Ford 1700 and while I had it in the shop, I decided to change all of the fluids and filters. I drained the hydraulic fluid/gear oil and it was a little dirty but not bad. I replaced the hydraulic filter because it was damaged and refilled it with the New Holland...

Hi I am new to tractors. I have a decent knowledge of motors but am totally new to diesel. I just picked up a 1700 2wd that's in decent shape. It starts up perfectly has no smoke from the exhaust and runs perfect. My concern is it smokes/steams from the crank case breather tube. It is not...

I need a new bucket for my Ford 770 loader. What is quick attach all about,what all is involved welding ect.:)

The hydraulics on my Ford 1700 tractor work fine when I first start it up but after it warms up they slow down and quit working. Every thing was ok one day and the next day I drove the tractor about a mile and when I got there no hydraulics. The PTO works fine, but the 3 point and the loader are...

I sold my 1979 Ford 1700 4WD. I had broken an axle and after looking for parts and the cost I decided I would make it myself. I made two axles at the time. I still have one and would like to sell it, if anyone is interested. The axle is made from 4140 prehard steel and needs to be welded to the hub.

I been reading posts as a guest for years (this site is great!) but finally decided to join and post for myself. I have read several posts about this problem but I had a few questions I hope you can help with. First off, most of the posts I saw stated their wheel fell off? Mine did not. The...

Hi all, I searched and couldn't find any posts about this issue: My '83 Ford 1700 has been great since I inherited it about a year ago. GREAT machine. Occasionally, it would be a challenge to 'quietly' either get into a gear or shift from one to another. This past weekend, it stopped...

I purchased a new water pump and was hoping to replace the thermostat, but when I took old pump and radiator hoses off, including port between upper hose and block, there was no thermostat. Anyone know where it would be located?

This tractor only has the warning light, no oil pressure gauge, but light seems to be operating correctly. Goes out immediately when tractor is started cold and stays out at even lowest idle. But as tractor warms up the light flickers on even at 1200 to 1400 rpm. As I run her back to put her...

Has anyone added power steering to a ford 1700 4 wd Tractor?

Oil was coming out the top of the steering column. I am attempting to replace the seal at the bottom of the steering column. I have everything loose I think but the outer tube will not come up off of the steering shaft. help?

Can someone please educate me on the following? When you grease the front king pins, do you keep adding grease until is squeezes out near the ball? I've put at least a tube and half of grease, so want to make sure of the process. Also, the manual doesn't state whether to screw in the front...

Hello Everyone, I have been using TBN for research for several months now and this place is awesome. I am currently looking at a Ford 1700 4WD with FEL, 4' shredder, galvanized box blade and 16' trailer package for a little over 7k. Tractor has had steering box recently rebuilt and the paint...

My ford 1700 started leaking Hydraulic oil from the top of the steering column. I took off the steering wheel disconnected the dash wiring and removed the 3 bolts holding the column down. The column wont come up out of the the steering "box". It is only up about an inch and won't come any...

Hi everyone, I am new to the forum....thank you all in advance for any wisdom or advice you can pass along. Last fall I bought a very nice low hour (550hr) 1980 Ford 1700 4wd. It's in great condition and was well cared for. It runs great and starts immediately every time, has great power...

I have a ford 1700 with a 770 loader. I would like to know the GPM for the hydraulic valve ( 2 spool ) that came with that model tractor. Had the old one rebuilt but it still leaks. now I am looking to buy a new or later model rebuilt valve .::)

After 960 hours and over 30 years my super Ford 1700 tractor's electrical warning light has started a steady flashing, on and off. The batery is fine, fully charged, all connections sound and clean. I just replaced the voltage regulator with a new one, same thing. When I unplug the voltage...

I have a ford 1700 4 * 4 iso 68 hydraulic oil is hot and not lenvanta well and do not get the trans fluid 80w90 I place him?

nesecito help I have a 1700 ford tractor recently installed by hydraulic steering rear linkage and now 3 pts up which can be very slow please help?

Looks like I have to replace my clutch. I have looked all over this site to find out how to tell if this tractor has a single or double clutch but have not found. It is a 1982 model, Ford 1700. One dealer said it was made with both, another dealer said it only was made with a single. Is there a...

I am trying to help a friend with a Ford 1700 diesel tractor. I know it was built by Shibaura. He says it has issues with the wiring being bad behind the dash. Can anyone post a wiring diagram for this tractor or point me to a web site where I can down load one? Thanks Sam

Hi, I new to the site but very interested in tractors. I have a small farm in PEI Canada and I'm looking for a compact tractor to basically play around with. What do you think of the Ford 1700? Thanks, Jim

Alright guys. I have read some forums on this site and other sites online about the axle hubs on this particular year tractor having a design flaw and being too small from the factory. I have owned this tractor for a year or so now and have been crossing my fingers ever since hoping that I...

The valve that works my loader also runs the 3 point hitch. It's leaking hydraulic fluid and I can't read the brand or part number. Northern Tool has some valves but I'm not sure if any of them would work, does someone know?

My hydraulics are not working correctly (very slow) and from the past I know it needs the filter and fluid changed in the hydraulics. Can anyone tell me where to do this on the Ford 1700?

Hi Everyone I am after a bit of advice I am looking at buying a Ford 1700 tractor, it however has a sticking clutch. Am I crazy for even considering it or is the fix not to hard or expensive? Thanks TOm

Hey guys, Going to start fabricating a snow plow setup for my Ford 1700 and am interested how some of you guys have done yours. I have a loader setup and am wondering whether it is better to use loader arms and remove the bucket and build a frame setup to mount my plow to or would it be easier...

FORD 1700 TRACTOR FOR PARTS Not mine for sale, just something I saw on craigslist. Steve

Gannon cylinder for 3pt. Hitch

Any idea what is a reasonable price to put on a Ford 1700 tractor? Has not run in some time, has 4WD, bucket loader with good hoses and solid metal. Wheels rusted bigtime. Rubber shot. 3 pt solid when last used.

Hey guys, Last year I purchased my first home and piece of property. Figured that I needed a tractor to start working my property, plow snow, mow my huge yard, and to just have a useful tool and piece of equipment around the house. Tractor came with the 770 FEL and a 7ft king kutter back...

i have a ford 1700 series 2 wd. my clutch linkage rod has started vibrating in and out from the engine/tranny block. it moves about 3/8 of an inch either way. it does weather th clucth is engaged or not. the only time it stops is if the pedal is pushed ever so slightly. im sure this is a problem...

Tractor has been running absolutely perfect, and I decided to do some preventive maintenance by replacing the oil in the fuel injection pump. This 1700 only has 400 hours on it. I have one of the injection pumps that lacks the drain and check plugs. This is despite having the following...

Hi all, This is a repost in the Ford section of the original post I placed in the repairs section. Ford 1700 starting problems I just bought a "slightly" used 1979 Ford 1700 tractor. It had some obvious things wrong and some not so obvious. I've had to replace the battery and will have to put...

Hi all, I just bought a "slightly" used 1979 Ford 1700 tractor. It had some obvious things wrong and some not so obvious. I've had to replace the battery and will have to put all four tires on at some point. The current issue is that it won't start. With the new battery, when I hit the key...

Has anyone looked-for/found a "close enough" replacement radiator for a Ford 1700? I see them on e-bay, but don't really want to pay $475+ for one (last radiator I bought was for a Pontiac Bonneville and was only $125). I threw some stop-leak in it last year and it held through the Winter and...

Tractor was running great today with no issues whatsoever.Turned it off to do some yard work and then went to restart it nothing would happen. Battery is good, horn,lights and engine block heater work with no problems. Any suggestions? Is there a fuse that could be giving me trouble that I am...

Hi All, My hydraulic fluid is pretty low - is it typical to "lose" fluid over time, does it kindof cook away? (this 1983 Ford 1700 is new to me so I don't know it intimately yet). Anyhow, manual calls for M2C-134A and Tractor Supply doesn't have it. Can't find any on eBay... Thoughts...