loader quick attach

Or Kubota LX2610's LA535 loader needs a new o-ring in the 1/4 in Parker 60 series female quick coupler. As far as I can tell, it is a 11/16 x 9/16 x 1/16 o-ring. Can anyone confirm this; most hydraulic sites don't list the actual dimensions. Thanks

Without going into a lot detail... I messed up (not due to abuse) & in-turn the loader quick attach bent. I know it is not a heavy duty unit, its what was on the tractor & we have never had any issues with it, as our loader is not that heavy duty of a unit either, we respect its limits. I'm...

I don't understand why quick attach adaptors are so expensive to buy. Has anybody built their own?Am I missing something? I recently bought a new grapple bucket meant for a skid steer and would like to use it on my farm tractors. I found these inexpensive parts available to speed the project...

Hi folks: This is on a 2008 Kioti CK30 with the KL 130 loader. It is routinely stored in a shed with one side open to the elements. One of the four quick attach fittings (the white one) is leaking. Hydraulic oil bubbles up in the gap at the top of the slip collar that locks the upper...

Has anyone used a 72” front plow blade on a John Deere 2210 tractor? Does it plow well or is the snow too heavy for the tractor to push? Should I stick with a 54” or 60” front plow blade.

Bought an RX7320 last year. Lost the grapple and tore hydraulic lines, and thought it was my fault. I figured I didn't engage the pin all the way. Fast forward a few months. We are religious about making sure the QD levers are fully locked and engaged. Used the grapple to drag some brush back...

Hi Guys, A couple of years ago I purchased a circa 2004 Daedong CK30 with an Ansung loader - a great little tractor with only 700hrs usage. It has a quick attach front bucket. I never thought tooo much about it until I decided recently that some pallet forks would be a good addition. I had...

Good evening! I'm Jon and I bought my first tractor a few weeks ago. A YM155D, with a YFL155 loader. I'm a complete rookie when it comes to tractors. I've got a lot of ideas and not much knowledge or wisdom. I'd like to figure out if I can get a bolt on QA conversion for the loader. After...

I was thinking of making some sort of either hydraulic or electric way to pull the levers down and up on the loader QA. Cant seem to find much ,I have hydraulics to the front of the tractor but would have to design the mechanical part and the hydraulics. I also consider two Linear Actuators (12...

Has anyone come up with a mod to make these into a standard style quick tach thingy? Need pallet forks AND bucket and no one makes forks for it. Really don't want to re-invent the wheel and looking for advice-pictures-products. Thanks in advance.

I'm looking for some help identifying the loader quick attach system that is on my dad's Massey Ferguson 451 Tractor with 1050 loader. It appears similar to a Euro/Global type connection but the dimensions between the top hook and the bottom hole don't appear to match. The top hook and the...

Recently purchased a 2013 B26TLB which comes standard with the loader quick attach. Having trouble releasing the bucket to remove. Loader quick attach handles just won't move to up(Release) position. I am following instructions in the manual. Appears bucket may not have been removed in quite a...

My loader quick connect fittings all leak. I flushed them out with no luck. The o rings must have damage. I think I will probably just purchase new fittings. I did replace the o ring once on one of them but it leaks again. I came across these: 2 sets 1/2" ISO 5675 Couplers 4AGF4-AG4F4...

I want to change my loader from 4 pin system to a quick connect style I have a John Deere 175 loader what is the best way to change and what brand does everyone recommend?? Thanks for the help.

On Teg's advice I'm going to give this one more shot w/ a better title and delete the other thread since I can't figure out how to change a title. I need a ssqa loader bucket and picked this one up at an auction - for what I paid for it I can afford to cut off the JD mounts and weld on a skid...

The loader hydraulic quick connect has a persistent drip. Is there an o ring that I can replace or do I need to replace both male and female ends? I flushed out the fitting thinking some dirt got in there. It still leaks. It looks different than most 1/2" fittings I have used. Like the ones I...

I have a Bobcat CT120 tractor with a model 6TL loader. One of the quick disconnects for the loader leaks (drips) whenever there is no pressure in the system. I have replaced the O'ring a few times over the years and the leak had stopped for awhile until this time, the leak slowed but still...

Was back dragging a brush pile with my pallet forks straight down and hit something. Blew the metal hydraulic hose and the pallet fork popped off on one side. Got that all fixed but now the forks or bucket won't stay on with down pressure. Have tried adjusting the nut on the loader quick attach...

My Max 28 that I bought last spring does not have a quick attack loader bucket. I thought I seen on here someone had a new Max 26 that did have a quick attack loader bucket? Is there any way this could be adapted to the Max 28? If so how much? I do have a set of fork lift forks that I had a...

I have a 2006 DK45S with a KL451 loader that has a skid steer type quick connect/disconnect plate to hook up attachments to. I just got the tractor (used) and have used the bucket that was on it when I bought it with no issues. Just bought a grapple and pallet forks for it and went to swap out...

I have seen a couple of threads over the years about this subject, but had a hard time finding good evidence of fit... here is my effort. I have a B2910 with a LA402-1 loader. I have envied the folks that had a factory solution to SSQA (or skid steer quick attach) because of the ease of...

Im considering this as an upgrade. Ford, New Holland Pin-On Loader to Skid Steer Quick Attach Adapter | eBay My concern is how much lift id loose with this on the loader? Currently the forks I use are hung on the bucket edge, and this really decreased my lifting capacity.Of cource they are quite...

I'm planning to convert my FEL to a universal quick attach, compatible with all skid steer loaders. After searching several posts on TBN, I got some very good info, even some drawings. This past Saturday I went to an auction and scored big. I bought a brand new 48" ASV(American Standard Version)...

Does anyone know if JD part W43359 (bucket Hook) will work for a 500 series loader (553 to be exact)? I have seen threads referencing this part for 300 and 400 series loaders, but not sure if the 500 is different. Got some free pallet forks coming and I am going to build a frame for them...

Hello, I am new to the forum and just bought my first Mahindra. A 2816 with a KMW ML106 Loader. After buying it, I discovered there are tractors with quick release front end loaders that allow owners to drop the front bucket and use skid steer type attachments like pallet forks and hay spears...

hey folks, Been a little while since I was posting.. but I have a small issue... I burst a hydraulic hose yesterday on the loader. It is the white marked hose, the bottom one on the LA463 loader. I believe it to be the curl return. anyway.. In the haste to get back up and finish the job I was...

I have a TC40 with a 17LA loader. One of the hydraulic quick connectors is leaking. Is there any way to service or repair the connector? If not what size/style of connector do i need to buy at the farm store?

I have seen several owners show pictures of the QA Coupler on a LA364 Loader. The QA is made for the B3200 Tractor but they have it mounted to a B2620 Tractor. I have a B2920 Tractor and LA364 Loader and would like a QA coupler for a snow blade I am ordering. Kubota does not want to help on...

Hello Again: The quick hitch on my John Deere FEL was almost worn out. The lower pin holes had walled out to the point that it was difficult to change attachments without getting off the tractor. I repaired the pin holes by cutting the holes large enough to accept a pin boss made from DOM...

looking for set of forks help

Hello everyone - I am in need of converting the loader of my 1997 Kubota B21 to accept quick attachments like a skid steer does. I would like to have forks and possibly attach a small snow plow. I checked with a local company for the conversion but the cost was pretty expensive since theirs...

I'm looking for the male part of the quick connect fitting. it has the following on it, FASTER nv14-38saem-08Bo. I can't seem to find a cross ref part. thanks edit: loader quick connects

I asked my dealer about 2 weeks ago to order me a QA Kit for my LA504 loader....dealer said "No problem".....then called back that day and said it would be to the dealership on 3 August. This morning my dealer calls and says that Kubota now says that it would be sometime in September before...

Finally found someone to cut me some quick attach plates so I can build custom attachments easier. Sure does make the job easier than cutting them out with a hand torch.

Does anyone know a part # for the o-ring in a 1/4 hydraulic quick disconnect coupler. I removed my loader on my BX24 and when I reconnected it, I pinched the o-ring. The parts manual shows the coupler $24.95 :( but no breakdown... Thanks, Dean

In building my own loader, I'm starting to think about my options for a quick attach system for the bucket. That thread can be found here Does anybody recommend one system over another? Also if anybody has some photo's that would be great as well. BTW I looked at using a standard skidsteer...

Is anyone else having problems with theirs leaking? I have Appr 250 hrs on my 4720 and the fittings started leaking. I have replaced o-rings but they leak when the tractor sits for a few days.... Thanks

Hi, I'm looking at buying a 2415 with loader, and I'm not sure if I should get the quick attach adapter for the loader. The tractor will be used for mowing, and for general ladscaping duties. . . What are you thoughts? Thanks, Darryl

I would like to find a skid loader quick attach adapter to fit on my Yanmar 330D loader. Does anyone know of anyone that builds these or has the hardware to build one? thanks jerry

I have a bush hog 2426 loader with a quick attach bucket. Can someone tell me where I can find the quick attach brackets to build my own attachments?

I have a Bushhog brand loader and would like to build implements for it : forks, grapple, etc..., but can't figure out how to build the "Bushhog brand" type quick attach. When I ordered the loader it was my first and I didn't know to get it with the Bobcat style quick attach. I have the...

I have a Bush Hog M446 loader with universal skid steer attach plates. The universal skid steer attach plates are attached to the loader with four large pins. If the attach plate is removed from the loader then can I attach pin-on implements to the loader? Or to put it another way are the...

sorry -- I moved this to Attachments

Hi, I took my loader off for the first time last night, was really quite easy to do. The hoses on my loader all have colour coded rubber caps for each of the 4 hoses that are attached to each hose. On the tractor itself, the couplings only had a colour coded plastic ring behind each coupling...

This post is for my questions about the brackets that are on the loader arm (the ones that attach the arms to the bucket - the ones that occasionally break on the 3X20 and 4X20) - mine were originally painted green but over time (and the removal of the buckets and plow) the paint has come off...

I recently removed the FEL on my Branson 2910 to gain access for the 50 hour service. The system works pretty well to remove it. It was off for about a week and a 1/2. When I reinstalled it and hooked up the hydraulics, one of the quick connects started leaking. Do they sell the female QC's at...

Has anyone tried to replace their loader quick couplers on a class III boomer? One of mine is going bad (leaks all the time when connected to the loader). It does not look real easy to get a wrench on them to get them off. I would consider removing the loader mount on the tractor but at least...

While my new TC45DA with 16LA loader sits poised for delivery to me (yes, it's killing me), I am supposed to decide whether to have my trusty dealer install the quick attach option to the loader, which will allow it accept standard skid steer attachments. Although I will have use for pallet...

My hydro quick connects, well actually only ONE, the red one, sometimes has trouble. It won't latch and at times when installing the loader, and other times it will not release, when trying to remove the loader. I've checked to make sure the connector was clean from dirt. Played around with it...

I've got a New Holland 14LA load with the QA bucket. I want to buy the QA plate that fits the loader so that I can fabricate my own implements and use the QA feature. Does anyone have recommendations on where to buy, where not to buy? NH wants about $180, I've seen them on Ebay for about $100...

My CC7360 has the 485 loader with quick connect bucket. Now I know that this loader was made by Woods. And I have heard that the quick connect is "standard skid steer" quick connect. I am interested in buying a skid steer snow blade to plow to the garage, barn and paddock. So as I look at...

Is the LA 402 loader for the 7800 or 2910 have the option of quick attach? I want to attach the forks and other options possibly down the road and after getting everyones advice on staying with Kubota loaders vs. woods, felt I should plan all this out prior to spending a lot of money. Thanks...

Anybody seen these yet? They're on ebay. Supposed to be able to swap out the bucket for forks, rakes, etc in about 1 minute. Uses a system similar to that used on bobcats. SHF http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=1921824504