replacement

year 2003, engine model #54DD, part #4264400M91 is no longer available! It's a under the hood, vertically exhausted, 4 cylinder, 2.8 L, 55 hp Iseki made tractor for Massey Ferguson. No aftermarket supplier. No response as of yet from my email to Iseki in Japan. A MF dealer suggested I try...

Hi all. I was having an alarm come up which I found to be low brake fluid in the reservoir. I quickly topped it off with dot 4 brake fluid which it took very little of, maybe 250ml/0.06 gal. Reading now, I should have used ambra LHM fluid and that dot 4 brake fluid will wreck the seals. I...

In dismantling the carb I had a screw on the main jet shear/break. I think it is an aftermarket carb unit - I do not see any serial number on it anywhere. What is a recommended replacement unit (ie reliable)?

I've had a 7900 now for around 20 years. Mostly never had an issue with it but a few months ago it became difficult to start. After all the usual attempts to fix it I found the issue was the coil. The coil has what looks like a screw that the plug wire threads onto. It looks like water (or...

Looking for a replacement tractor seat for my 1984 S470D Buck tractor. There are a staggering number of options out there, but very few if any would seem to be an exact fit or drop in replacement. I don't necessarily want to get a duplicate of the original, as there appear to be quite a few...

Hi All. I have a B3000 and the top Amber clearance light bulb is burnt out. I have been instructed to Pop Off the cover using a very small screw driver or pick in the weep hole at the bottom of the light. But once I get the cover off, I'd like to have a replacement bulb at the ready so I...

hello... i have an old case 1816 uniloader the aux hydraulic pump has a bent shaft... still works but has quite a shake to it. need to find a replacement and not having much luck. its a borg warner pump # on the case is S125OAK 55R under that # is 05098 can anyone give me an idea where i...

hello... i have an old case 1816 uniloader the aux hydraulic pump has a bent shaft... still works but has quite a shake to it. need to find a replacement and not having much luck. its a borg warner pump # on the case is S125OAK 55R under that # is 05098 can anyone give me an idea where i...

Hello All, I am new hear but I am working on my John Deere 5400. I installed a Reman Complete Clutch from John Deere. My main concern is that when I put the tractor together the clutch pedal was very loose and I had to pull out all of the adjustment to get it back into clutch play spec. I am...

Today having 1922 clay sewer laterals replaced with heat welded 4” plastic… The clay needed annual root clearing so the idea is to replace and be good for another 100 years. The contractor uses only Kubota b26 tlb and had two on todays job.

I'm told that I need a full knee replacement, I was asked which I'd prefer, the robotic assisted or the traditional. Having been asked this by the doctor I thought, how could I answer it. This is my first time receiving a full knee replacement and I've never performed the surgery myself so how...

I noticed transmission fluid on the floor under the right rear axle. The rubber seal (bellows) for the brake actuator rod was leaking. The CNH bellows is part #47864249. Removal Place the tractor in gear. Block the wheels, front and rear. Unlock the left and right brake pedals. If replacing...

hey guys I unfortunately need a new turbo for my 2004 TV145. The dealer price on them is quite a bit over my budget. Do you guys have a recommendation for reputable companies that sell turbos for my model?

During the transmission repair, I noticed a fair amount of hydraulic fluid leakage coming from the joystick area, thinking that the O-ring hose fitting connections need to be replaced to fix leaks. Anyone replaced orings?; what size was used on YM 180D's? Details below. Front End loader and Hyd...

I broke my rear window on my 1025R 2018 JD Tractor a few weeks ago. I got a new window for $1,263.81 and put it in myself - no problem. BUT, I will not buy another one if I unfortunately do it again. I saved the old parts and put it all together again with 1/4 inch plywood and plexiglass. I...

Well, I've gone and committed to replacing the engine on my X585. I'm approaching 1120 hours on the FD711D engine. Compression is minimum spec on one piston and below spec on the other (90 and 70 as I recall). It is also burning at least a quart of oil between oil changes - enough that you smell...

Tractor is around 6 years old. Battery still works, but now has some attitude while cranking the engine over at 60 degrees outside. I decided to remove and replace the old battery for new now while the weather is still favorable. I have changed numerous batteries on numerous machines in the...

Doing a little work on the old International 606 Diesel. Trying to get the brakes working. I picked up a brake kit with new bearings, springs, and friction disks. But, one brake won't hold together without replacing the brake actuator stud. A small stepped (shoulder) bolt. I called the...

Is there any one who has either searched and or replaced their CT 235 seat recently and if they have what supplier and model did they use? Any help in this would be greatly appreciated!

Time is getting near for a full shoulder replacement. Started about 15 years ago whitewater kayaking. Turned out I had arthritis in the right shoulder. About 10 years ago, it was brought up I would be looking at an operation. 5 years ago turned out it's going to have to be a full replacement...

Anyone know if there's an aftermarket radiator for a Branson 4520-C that doesn't cost $700 ?? I took it in for a cleaning and they told me it has a hairline crack on the plastic top. In my experience JBWeld fixes everything I've used it on, including hard to reach copper water pipes in my house...

Does anyone know where I can find a New Holland TL90 tachometer? A relative just bought a TL90, but without personally inspecting it prior to purchase.

has anyone replaced a woods finishing mower gearbox with a brand other than the expensive woods replacement?

I know my wife shouldn't use the zero turn like a bush hog, but she does, and that isn't going to change. Occasionally the inner deck baffle gets bent and the blades hit it, so I jack up the deck, get on a creeper and beat it back into a reasonable shape with a 4lb sledge hammer since that's all...

Got a grease zerk that won't take grease. I've got one of the tools that you put oil in and tap the piston to clean the zerk. Although it has worked on others, it has not on this one. I've been unable to unscrew it using wrenches and, next a pair of vice grips. It is the zerk to grease the...

I just bought a Massey Ferguson 1734 with a L105E loader on it. The joy stick for the loader is damaged. Looks like the joy stick broke off ( maybe something fell on it) and someone tried to weld it. They did a lousy job. Anyway up and down works fine but the bucket twist jams when dumping and...

Hi all, My saga continues. I replaced the battery cables and thought that my starter problems were solved but not so. Still randomly clicking so I decided to upgrade the ignition switch to the NAPA KS6600. I was able to find one for $ 50 with my military discount and thought that it would be a...

I have two Milwaukee 3013-20 telescoping pole saws, and they are awesome using good Chinese 9 or 12A M18 battery packs (I use Waitey and especially Stairlie branded 9A batteries with good results). Anyway, for whatever reason, the internet doesn't know any knockoff chains that fit the 3013-20's...

Guys, it's getting near rear tire replacement time. My L-3010 rear tires are 3/4 worn and the rubber is hard as a rock. Other that the Kubota dealer.....where does one go to BUY....and MOUNT these tires? I've seen them on-line but WHO mounts them? Might anyone venture a guess for the cost...

If you ever price a new seat cushion for your Kioti tractor you will cringe. New Kioti cushions are over $600. I replaced my bottom cushion 2 years ago. It already has cracked in several places. This time around I said screw it and bought a folding seat with armrests from Vevor for $120 shipped...

I have a baumalight 1p24 stump grinder and while using the grinder the PTO Shaft separated and rounded out the outer tube since it was cut too short. The PTO Shaft looks to be a series 5, but finding a series 5 replacement shaft at a reasonable price seems to be hard to do (most are coming out...

I am looking to replace the front loader hoses on my 2004 3510 "New Sheet Metal" with ML112 loader. They are 18 inches long. Am I right that they are 3/8" JIC? Are they 8F or 6F swivels? Part number is 22506506018 (#3 in the PDF of the diagram out of the manual) Standard part has swivels on...

Saw all the videos. Wanted to put the motorcycle springs under my seat. They look and feel amazing. Only problem - they are a smidgen too long and the seat does not lock. Normally not a big problem, until my East Tennessee rear end bounces once or twice and the pto shuts off. Suggestions?

I am looking at a TYM T574. The lower seat cushion has to be replaced. I have not found it online. The entire seat costs $1270, and people say TYM's seats are not great. Is there a good aftermarket seat cusion that will fit? I don't think TYM offers the cushion by itself.

My insurance needs are changing on my tractor and I'm looking to get a quote from my insurer that includes actual replacement cost of my tractor (currently I only have actual cash value coverage). I purchased mine in 2021 and it currently only has 58 hours on it. With all the economic changes in...

Hello to the brain trust.....New Holland TC33DA hydrostatic had a bad clutch. Got inside and found oil in the clutch housing and this(photo) what in the hell does anyone think it could be. Def signs of mice around the tractor but this is so consistent one thing almost looks like it grew there...

Hey everyone I have the snowblower listed above and I need to replace the shear plate. Does anyone have any experience with this job? Any videos available out there. Thanks

I have been trying to find a replacement suspension seat for my 2006 Kioti DK35SE with no luck. I have spent so much money already trying to buy replacement cushions but I really need the suspension seat. My back is killing me after only a few minutes on my machine.

So after removing, fixing and reinstalling my broken rad I filled it up with coolant flush/ water and fired it up. No leaks from the repair, but there was lots if white smoke and the rad was bubbling like a boiling kettle! Shut the tractor down and called it a night. Went back the next day after...

Are there any cheaper transaxles that will work in the place of the Hydro Gear ZT-3400? I have a 10-year old Gravely Pro Turn 160 that the transaxle housing and cover busted near the rod that connects the left and right together. I recently acquired more yard to mow, so will likely upgrade to...

I had to replace my leach fields in December do to a blockage after 50 years, not complaining. Contractor because of the weather finished the job in December up here in upstate New York. During the new installation, the weather went from very wet to frozen dirt during that replacement the...

Anyone have experience with the aftermarket hood and cowl for Deere 4400 series? There seem to be a variety of mfg, suppliers and prices. Like this https://www.amazon.com/gp/product/B0DY1WZWTQ/ref=ox_sc_act_title_7?smid=A3QEAIM7YYCNN4&psc=1 and this...

I have a NH T1510 that I bent the 3 point arms on. Completely my fault. I got my bush hog hung up and it twisted too much. Anyways...where can I get a good replacement set? I have purchased two different pairs (one online and one from Rural King) of "universal" arms. They both bent as soon as I...

Buddy of mine gave me an 021. He's in his 90's and cant handle saws anymore. Him and his wife are very dear friends; I help them with projects and stuff. This thing has sat for a few years. Have been cleaning it up. It fired up with fresh gas, but the bar and chain have rust and crust. It has...

Hey All, My rear blade is cooked and not doing it's job. A lot of my use is with the snowblower, and it's been windy during the winters leaving my using it more than I would have thought. Anyways, when I looked the part up, bills had them at a very high price imo...

Recently my alternator went out on my 2016 tractor. Appears to be internally grounded. (Drained a battery and starts smelling then actually smoking as soon as a new battery is connected, before starting.) Part number is 40266110. It is a 70amp. I'm having trouble sourcing a replacement at a...

Looks to be time to replace one of the knuckle seals since it's leaking pretty good now. Just ordered the seal and the process looks pretty simple, any concerns dropping the lower axle housing or just have at it.

I'll try to keep the sordid story as short as possible..... I am running a MIVA mini ex with the Rato R420 engine. I added two computer type fans for cooling then a few days later found the battery dead (after about 25 hours of running). I recharged the battery then once running (3000+ RPM) I...

Lots posted on batteries here lately, so here's my contribution. I'm not sure what's going on with Kubota batteries these days. It's been my experience that they used to average 8 - 10 years. The one in my L6060 died after just 3. No indication on the battery as to who makes it, it just has...

been a long time. My tractor has been sitting for way too long. I was hoping I could find somebody reasonable to replace my hydraulic hoses for my backhoe. I couldn’t. I have to do it myself. I have a 4500 Ford industrial with 755 backhoe The hoses that go under and up to the manifold seem very...

My YM2500 has no brakes at all for the left wheel. The right side works ok, but I can press the left brake pedal with my foot as far as I want and I have no brakes. From looking at the parts breakdown, I’m pretty sure I can do this myself if I take my time. Hopefully, Fredricks will send me the...

Have loosened/removed the retaining plate around my 2008 Mahindra 4110 rear brake boot (where the brake rod goes into the rear axle), but don't know how to "break" the rod apart to get the old boot off the rod and the new one on. Anyone done this and have any advice?

Does anyone have experience with Caltric replacement parts? The front hood of our X590 has been severely damaged. We've been patching it on with duct tape for the past several years, but it's barely hanging together and opening/shutting it has to be done very gently, lest the whole thing fall...

Seasons greetings all. Was swapping out my loaders bucket for my snowblade as is sop this time of year. Before doing so I flattened some small saplings to make room for snow movement in the event of some heavy snow fall this winter. I noticed one of the front wheels seemed to be...

Dealer put a big scratch in my 3033r's seat, back when the tractor was new and in for a warranty issue. Not thinking it was too terrible, I never did anything about it. Fast forward a year or two, and the seat split along that scratch, and now the foam is spilling out. I've played the game of...

Hey folks, figured this would be a good place to post as I know from reading here for a 10+years that there are some people that muscle through recovering from surgeries and find work arounds to getting things accomplished despite impediments. I'm 47 years old and am happily staring down the...

I bought LED lights for my 3020 and replaced the seal beam lights, I now get sort of a strobing effect with the lights. Does anyone know what would cause this?

Idk how it happened, was just clearing some brush, nothing heavy or crazy. Next thing I know, I can’t tilt the grapple up and I look down to see this, a bent hydraulic lift cylinder. I have looked for a replacement and can’t seem to find one that fits. I have a Mahindra 1626L HST(2021). I have...

I purchased a Ford 1910 4x4 in very good condition but the 770B loader valve is worn out. I plan to purchase a new single joystick 2 spool valve with float and power beyond, but I want to know if anyone out there has done this before. I would like to purchase this from Surplus Center, but I need...

The LED display on my break away box is getting pretty rough from exposure to the weather. When I used it last week or so, one of the wires broke off of the sealed charging circuit. So, I think I will just replace the whole box. The trailer mostly sits so I remove the 5 AH battery and put it on...

I recently split the tractor and removed the worn clutch. Shopping for clutch's, throw out bearings, gaskets, etc. Can anyone recommend a website or parts store? Google search for 1920 brings me to ALOT of sites, mainly eBay. Be nice to hear someone else's experience on this. Also, I'm...

My top link has either been bent slightly or seized up. Either way I need a new one. Kubota top links are over $200 which seems ridiculous. Will the top links TSC and other sell work just as well? I would think so, but wanted an opinion from here. THanks

Needed to do some chipping yesterday, but before I could do that, had to replace the "twig breaker" on the Wallenstein BX42 chipper. Well, didn't have to, it will work OK without it, but it helps break up stringy stuff. Not sure if other chippers have this but thought I would show the fix, up...

I damaged my loader arm, up by the rear pivot. I called my local dealer and they advised that loader has been discontinued. I am looking to replace the frame- bucket, hoses, pistons are all good. Are there any newer model loaders that fit?

I have a Branson 3510i that had a bad throwout bearing. I was able to split the tractor apart. I wanted to have the flywheel machined before reassembling but the flywheel has a secondary damper disk (similar to the damper spring assembly on the clutch disk) that covers the bolts that fasten the...

My LK3054 rear wheel rims have been slowly rusting from the inside-out. My local Kioti dealer tells me none are in stock and he has no idea when a replacement could be available. Does anyone have knowledge of a third party rim supplier that could help with this? Additionally, I'm unsure how...

A few days ago I noticed that the Red/Yellow Lens on one of my rear signals on my TC35 was broken. "No issue" I thought, as I went inside to look up the P/N and order a replacement. The NH Part Number is 86576123. Its cost is..... $55 (each) ??? wth..... On a whim I checked Amazon. The...

I have a older Lode King seed tender that has 2 hoppers. We use it to fill our seed drill with grain and fertilizer. The manifold has quit working on the seed tender and I need to figure out a replacement for it. The manifold works by attaching to tractor hydraulics, and tractor battery for...

Looking to find a replacement strut that centers the joy stick on an older Mustang SS 2060

Does anybody have a video on how to replace a drive shaft from motor to hst on tym 200 or similar tractor

I think this might be coming sooner rather than later. I had an appointment with an orthopedic doctor back in June about my ongoing battle with plantar fasciitis in my left heal and pain in my right ankle. He gave me some orthotics for the plantar fasciitis and a "to-do" list of stretching...

i bend my curl cylinders (running it without the kidney brackets) and now they started spraying oil, so they are dead. has anyone ever replaced the cylinders with some aftermarket ones? i really dont feel like paying around 1200$ for 2 OEM cylinders. thank you

The tachometer on my Ford 1900 has failed and I am looking for a replacement. The original part (SBA385450180) does not seem to be available anywhere. Is there an alternate tachometer that can be installed in a Ford 1900?

Hello, Has anyone had problems with their Branson tractor’s water pump? I am seeking suggestions for what needs to be removed and in what order. Thanks

As mentioned in the thread "Woods vs LandPride Finish Mower" I ordered a set of wheel assemblies for my Caroni RFM this past Saturday. The UPS truck dropped them off today. They came from High Grade Manufacturing. Very happy with them. Link below. At $52 each (The whole works - wheel, yoke...

Hi All, I have to replace the bearings in the pictured 4-hole hub. Although it may be simpler to buy the whole new hub. A couple questions: Can anyone tell me if these bearings simply press in and out of the hub? I assume that's the case, but I've gotten myself into trouble many times before by...

So I hit a beaver-cut stump with my Woods 720X rotary cutter and sheered off the tailwheel assembly. Unaware that the wheel had broken off, I ran the wheel over and destroyed it. So I'm looking for an inexpensive tailwheel assembly that has a 1-1/2" shank that also has 8-3/4" free play between...

The belt part No: 754-0461Idler pulley No: 756-0116A Quite easy to replace the drive belt and pulley.

I'm replacing the dynamo on my B7800 after the bearing locked up and much squealing and smoke was released (belt). I have the new dynamo but have a very simple question. The two wires coming from the dynamo are the same sky-blue color and have the same bullet-type connectors as do the wires on...

Throw out bearing is howling when I depress the pedal. I figured I’d replace everything, clutch, pressure plate and TO bearing….then someone told me the tractor has to be separated in two. Who has done this job and how hard was it ? Thank you for any help

I just picked up a stump grinder that uses a conical bolt to secure the PTO shaft to the implement side. The shaft has a clutch so I don’t think it has a protective function like a shear pin. The nut backed out and it came apart. By some miracle, nothing broke and I found the bolt. I bought a...

Hey people I have a 18 year old Chinese tractor Dong Feng DF354 that needs the axle seals replacing. The trumpet housing will not pop out so now trying to remove the PTO, which also WILL NOT COME OUT... Tips or advice please.

I put a nice 90-degree bend in my driver's side rear tie rod yesterday. I had an old "emergency" tie rod that is/was a scabby-welded piece of junk (long story), so I decided to replace the bent tie rod with that until a new part shows-up later this week. Anyway, removing the tie rod linkage at...

I have a slide in range. Model is KSIB900ESS (slide in, convection oven / Induction top) stove. Suffering "F2-E0" error. Frankly, it's been quirky since day one. There are several boards inside. I'm trying to ascertain which one I need to replace. Had a repair guy out here a year or so...

Finally had time today to work on Allis. I got a new water pump from Steve@B&B and I got the tins stripped off, rad out, everything good so far. But before I go any further and screw anything up, how do I get this pulley off the water pump? Do I have to remove those nuts? I have never seen one...

Hello, I recently broke a pin (6806971) in my latching X-change, seems hard to believe given it's size. I believe the lock pin fell out and the pin worked it's way out then broke off. It appears that on it's way out the pin took the bushing with it, as it is half way out and cracked around...

ok the replacement pump comes with 2 gaskets and a steel plate which covers the impeller (the fan like thing that circulates the coolant) however if it is assembled with the plate in place it doesn't line up with the alternator and crankshaft pulley that drives the water pump; if I take the...

Hi folks the replacement water pump for my TX1510 (K3B Mitsubishi Engine)has a small outlet pipe (see picture bottom right) whereas the existing one does not(its got a 'plug' screwed into the opening - does anyone know whether this needs blanking off or attaching to something?

B3200HSD Loader Lever Block and curl control ball link replacement. Big ask -- hoping someone can tell me how to actually replace a failed part. PIA in terms of space and access. The ball link (part of loader lever control assembly) that controls my loader curl failed. The screw that goes into...

The Brush Hog SQ172 I got with a piece of property has extremely worn blades. I ordered some blades and bolts. Does anyone know the wrench size of the nut (part number 252BH)?

I have a Brown BDH-600 disc harrow, and one of the outer bearings on the rear of the disc row locked up. I've found the parts list on Brown's website, and looks like the entire trunnion/bearing assembly is DH-115A, which includes the trunnion (bearing housing), inner bearing, and c-clip. The...

My Kubota M7 manual maintenance schedule is to replace coolant every 2 years. Mine is now 7 years old and I decided to replace even though test strips said the original coolant was in excellent condition. I went by the manual except for flushing the system - based on test strip results and logic...

Dash display got flooded and not working. Anything to check first before replacing at cost of $1200? Checked fuses and seem good Any way to check that power is getting to the unit?

Today while backing my trailer into the woods I noticed a 30ft long 9inch diameter tree branch laying across my tractor. Bumped the exhaust, bent the steering wheel, flattened the cowling over the gas tank, and absolutely destroyed the plastic dash... Luckily the gauges just pushed down into the...

Just bought an older 9540 So far very impressed with its build quality Has anyone swapped the factory seat with an air ride seat at all ?

I'm looking for recommendations for the handle replacement of the bucket quick attach. I replaced one of the original handles with an OEM part but it had a pretty sorry weld job on it and it snapped off. So after taking a look at the other handle I found the weld on it to be cracked so now I've...

Hi, I have a JD 855 1987, i have some problem with the SCV, but to replace it, it's like 3000$. I found it dont have return hose, directly bolt and return on transmission housing. The question is, can i remove it, block the return hole and install an aftermarket flow divider and control valve...

I purchased a king Kutter (tractor supply "County line branded") and have had this PTO attachment for a few years. Facing the back of the mower deck, the right side mandrel bearings are shot and the mandrel is in need of repair. Is it better to just remove the mandrel and replace the bearings...

Can someone tell me the narrowest bucket attachment available for my bh77 backhoe and where to find other than paying dealer costs? I’m in need of a trenching bucket but I’ve read they load up easy so your off the tractor more than on Thank you

Managed to snap the input drive shaft (? - if thats the correct term) off on a Joyang JP20 /31 /F21 /S6 /L which was used on a 3 pt backhoe and am having a fit trying to find a replacement. Anyone have a line on where to find matching replacements or rebuild parts on these?

Hi folks, I have a 14 year old 800hr BX1860 on which I've just discovered the propeller shaft front joint cover (aka dust boot) (item 20 below) has worn through and fallen off. Interestingly, the damaged boot was just sitting atop the MMM deck which I had pulled off for springtime blade...

I have a 17" Steel City drill press. I replaced the chuck because the old one was having issues. The new one is having issues staying on as well. At this point the taper on the arbor is rather chewed up & was likely the cause of the original chuck issues. Pulley alignment has always been a bit...

So the deal appears to have gone through and partial financing approved. I will soon be the owner of a 2015 Challenger MT655E. https://www.tractordata.com/farm-tractors/007/6/4/7648-challenger-mt655e.html Don’t worry about the blue cap. It’s been taken care of. Snowplow frame removed, too. ;)

Need replacement front turf tires for Jinma 284 tractor. 26 x 7.5 -12. Anyone know where I can find 2 replacements. They have dry rotted badly and one

Need replacement front turf tires for Jinma 284 tractor. 26 x 7.5 -12. Anyone know where I can find 2 replacements. They have dry rotted badly and one

The manual says: KUBOTA SUPER UDT-2 SAE 80-SAE 90 gear oil Why specify 2 options? From what I've read it ships with UDT. Recommendations? I'm looking at buying the AMSOIL SEVERE GEAR® 80W-90 100% Synthetic Gear Lube for it.

need new batteries, can't find anything on this machine! or can i just throw any battery in it?

Hello, 2010 RTV500 (approximately 100 hours) I'm having trouble removing the oil seal from the differential. I have the CV assembly removed. Does anyone have any advice? Bonus question is to how/why the seal is leaking. The cv joint doesn't appear to have any damage.

Seems I need to replace a hose on my GC1705's FEL (DL100)... part SL103366. The tractor/FEL is around 10 years old, and is stored outside. Should I be looking to replace all the hoses at this age, or should they generally run longer? Is there a standard replacement interval? Is there much of...

Does anyone know of an exact drop in replacement for the lift cylinders on a B219 FEL? As I am crazy overloaded with things to do these days, a swap would be far more time efficient than a rebuild of the old ones. I don't have the tractor with me right now, but I will pull a cylinder next time...

So the title pretty much says it all. I sold my MX-270. Bunch of reasons. Had great power, but the CAPS pump always had me nervous (they were always a surprise failure) and that was a big reason. Another was parts availability was dwindling. Never had anything I couldn’t find, but the spool...

I need a replacement tractor battery for my Kubota L4600. Where is the best place to get one. Can I buy at a Sam's club or Walmart? 12V, CCA: 582A us what I think I need according to specs. I got lucky the original battery lasted almost 10 years.

My 2017 Kioti CK3510 would not start. A dealer diagnosed the problem as a bad IMV Valve. The OEM valve (EH15-0016A) was quoted at over $800, and that was only for the part. Online research verified that that was indeed the case. My question is, with so many IMV valves available for well...

Recently replaced the fuel pump on my 07 Branson 3510i and now I can not get above 1200 rpm

Looking to replace the seat on our satoh beaver. Any recommendations on something that would be compatible with the current seat mounts?

I decided to do this myself. I couldn't find any videos on it but I found it really wasn't that difficult. Here is the video I posted. If anyone has leaks or needs info on how to do it check out the video or ask here and I'll see if I can give some good info:

Hey ya'll I'm back with another DIY farm repair, this time replacing the master cylinders on my 1998 555E backhoe. When we bought it the brakes were okay but a little spongey and after a bit they stopped working. We bought a pair of rebuilt master cylinders online and swapped them out ourselves...

Service bulleting 210 https://d1o0i0v5q5lp8h.cloudfront.net/bcsame/live/assets/accordion_entries/resource/Service%20Bulletin%202-10%20-%202022.3.2.pdf This PDF lists all the correct cable part numbers for all of the different BCS tractors broken out by tractor model AND serial number range...

Looking for source for Kubota KX040 (lower) Windshield replacements. Would prefer polycarbonate but understand that is in short supply. Will be glad to use tempered glass. I can find them for the KX080, but thus far not for the 040. Do these cabs happen to be the same size?