john deere 2210

Hey everybody. I have an 04 John Deere 2210 that has constant power with the key off. Also won't start and the dash lights turn on and off when I sit on the seat and stand up from the seat. Any suggestions help. Thanks.

Following my earlier note regarding play (a lot!) in the rear splined section of the driveshaft, I've bitten the bullet and gone ahead and extended the shaft by 18mm. The rear yoke is now fully engaged on the input shaft of the transaxle - in fact, the shaft extends into the yoke itself by about...

So grateful for this forum! I have 3 tractors: JD4600, JD332, and the newest (to me), the JD2210, all Yanmar diesels. The 4600 and 332 both start on the first compression stroke and never skip a beat. They start up like a clock. The 2210, on the other hand, with 380 hours, in the winter...

I've got my 2210 apart again giving it a total clean and service (last was 2019 and over 200 hours ago). While I had the deck off I noticed I had some noticeable movement in the driveshaft when running. I've got all this apart, and the issue is more with the sliding spline fitting into the...

My 2003 JD 2210 with 151 hours was running fine and just stopped, then it would start but shut off within seconds. Now it turns over but does not start. I have done the following: - Blew out of the fuel lines - Fuel shutoff solenoid is working properly - Fuel is flowing to the intake side of...

I have yet to see any reports of issues with the parking brake on the 2210, so I guess I get to be the first. The plastic parts on JD tractors are a blessing and a curse. A blessing because the replacement parts are generally not horribly expensive, but a curse because if they were metal...

JD2210. 62C mmm. 1100 hours. Been having this issue for a few years. Tractor runs perfect when not mowing. Just finished major service, fluids, filters, gear oil in mmm and all zerks greased with new blades. Still has the same issue mowing. After mowing for about 45-1 hour the RPMs will drop...

Anyone know of a sickle mower for cat 1 low hp tractor - 23hp. Thinking 5-6 foot max

500+ hours, cab, mid mount mower, FEL. Real nice shape. Prices on the net seem to be all over the place. Thanks Ryan

Lately my JD will run ok doing some shredding or belly hanger mowing. However, after about 15 minutes power starts falling off fortunately I can make it back to the shop when it stalls and will not restart. I've changed the fuel filter although it didn't look clogged. Then it restarts and...

Hello everyone. Noticed oil leaking onto the rear rim right side, possibly on the left side too. But definitely the right side. 1089 hrs. Called JD dealer for quote to change a $6.00 seal. Told me it was 20 hrs labor at $100 per hr. $2000.00 Also told me the transmission had to be...

I got this Tractor as a barn find only 85 hours. It hasn’t been turned on in years. When I go to turn it on all it does is crank. I emptied all the fuel out of it and replaced it with new. Still does the same thing. All the fluids are full. I pulled off the injector lines and they had fuel but...

I ran the 2210 VERY low on fuel because our local fuel delivery took quite a few days to get to me. Once they did, I fueled it up, along with all the other tractors, and drove it over to the storage building. On the way I heard a squealing sound and smelled an unusual burning smell. The...

I've got a JD2210 diesel ~500 hrs. I think the whole thing was made by Yanmar and they put JD green and logos on it. I was using it yesterday, moving things around with the bucket etc. I parked it and then today went to start it. Nothing but click. Sounded like classic bad battery, cable...

I have noticed that my 2210 will start rough if I start it at 1/4 throttle. It will misfire and puffs out a lot of diesel fumes for the first few seconds before cleaning up and running great. If I start at idle throttle setting it wakes up a purrs without missing a beat. Anybody have any...

Looks like some wire got wrapped around my axle and it tore the seal apart, so constantly filling hydro oil. Has anyone replaced the seal? Is the gasket just RTV sealant, or is there an actual gasket- I don't see one on the parts diagram.

Hi Guys! I have had a JD318 and then replaced that with the diesel 332 a few years ago. I have always done my mowing with these 300 series tractors and am happy with them. But I want a front loader and 4WD. So I'm thinking of upgrading to a used JD2210. I have a concern about the upgrade to...

My usual pass through the postings for the day on Craigslist landed me on a Curtis Cab for my JD 2210 only 1 hour away. Been looking, looking and even contemplated building one using purchased. This one has all of the options front and rear wipers, mirrors, front and rear lights, hard side...

The rule of thumb is five horsepower per foot of rotary mower. With a 23 HP engine and 17.7 PTO hp I don't believe I'd go over four feet with that tractor. The tractor is also a bit light for the five foot mower. With a 700 pound three point lift capacity you should be able to handle it but a...

So i think i put the loader on 'wrong' the last time i did it. I went today to take the loader off. I popped the front wheels up in the air, pulled the two front pins, and then pulled back on the stick and the loader raised up like i normally would. It didn't drop onto the two front parking...

So I pulled the snowplow off the 2210 today and installed the mid mount mower deck. Everything was going great until I pulled out the yellow pto knob and got a big nothing. The short version is that all is now well. There are several threads dealing with this around the net but I have a...

Morning Gentlemen and Ladies. Since 2004 I have a JD 2201 SCUT which I absolutely love and it has done everything I've wanted to do and even more. However the other day I had the tractor up on a steep hill, parking brake on, in neutral, and idling.. everything was and has been fine.. I got...

I own a John Deere 2210 with a Woods BH6000 backhoe and 2 of the 4 port relief valves are leaking. The 2 that leak are mounted on the upper part of the spool valve. One of the relief valves is set for 2500psi and the other is set at 2000psi with anti-cavitation check. I am not clear on the...

My orig seat has totally come apart. Does anyone have any experience with a replacement they can share? Thx> Eric

Locating the zerk fittings on my JD 2210 drive shaft forward u joint has become difficult. I have posted pics that possibly someone can help me out. 3 of the pics are the u joint side away from the engine and one is from the engine side. Thanks for any info possible.

JD 2210, Can I attach the loader with the quick hitch still installed? I think we are done with the snow for the most part. I would like to remove the snowblower and attach the loader now, but would like to keep the quick hitch installed just in case I need to attach the snowblower or plow...

I am new to tractors and this site but I need help. My tech manual is on its way but while I am waiting: 1. Do I drive the sleeve onto the steering axle dry or use lube of any sort? 2. Do I drive the seal into the housing dry or apply a lube? 3. Lastly do I drive the seal into the housing...

Hello all, I need some help. I would like to buy a pair of wheel spacers 2"-2.5" for my JD2210. I am unable to locate the bolt spacing. I know it is 5 bolt but is 2.5" spacing correct. I know JD has wheel spacers but they are only 1". I am after the 2"-2.5" because my property is on a hill...

High everyone. A quick question. I bought wheel extenders for my JD2210 tractor and would like to use longer wheel lugs to secure them to the axle. I can not find the metric values. Is it a 10x1.25 or a 10x1.50? And does anyone know where I get them that are about 35-40 mm long. I can cut...

Hello all first time poster on this forum. As the title states I own a 2008 2210 with 700 hours on the clock. From the previous threads I've read prior to the purchase of this tractor a few years ago. I was aware of one the plastic cooling fan that's valuable to damage and the u- joint being...

While awaiting spring I figured I'd look at what maintenance the compact tractor would need. It states @500 hours to do a valve adjustment and "check fuel injectors". The valve adjustment looks simple enough but the only item in the service manual for fuel injectors is a off engine test which...

Bought used John Deere from dealer with 650 hours on it. Got it home drove it off the trailer and about 100 feet later, made loud noise when hydraulics were maxed out. Steering, or three point or FEL. Once that happened there was no hydraulic power until you stopped and restarted the engine...

My jd 2210 tractor won't start. I've had the battery and starter tested by dealer, replaced the switch per their recommendation. The dash lights come on, but starter will not engage. What am I missing?

Hi All, I have a 2005 John Deere 2210 tractor that has developed a couple leaks and I'm looking for advice for the best way to repair them. The first leak, which is pretty significant, is coming from the top of the Power Steering Valve (See pic and diagram). It appears to be coming from the...

Hello folks, first post, got an issue with the 4wd on my 2210, i have checked all the basics, not getting any power to drive shaft going to the front axle. Anybody have any experience with this problem? Thanks

Hello, I disassembled the tractor yesterday to have access to the drive shaft between the engine and trans. I have a bad ujoint and want to replace both ujoints while I have it appart. My current issue is that I cannot spin the shaft to have access to the snap ring that holds the shaft on crank...

Hi everyone. Was using the tractor removing snow the other night, and noticed when I put the throttle up I was getting some vibration and a different sound like a fluttering sound. My son told me he's been hearing some clacking sound for awhile but I thought that was just a normal diesel...

After fixing a few issues with my new /used tractor I found a new one (sigh) One of the lift cylinders started leaking ...the Piston (shaft ? ) has some dings in it and most likely tore up the seal? I have been looking online for a new unit or just the piston shaft and seal kit with no luck...

I have an issue right now. I have a 2005 JD 2210. Plowed some snow a few weeks ago then boom, the tractor died on me after using it for two hours, full tank. Went to turn the key and it only clicked and never turned over. Had to boost. Started it up and ran fine. A couple weeks later, it...

Looking to add a tooth bar to my 2210's FEL. Lots of options out there. What tooth bar have you added to your FEL and would you recommend it?

Does anyone have any good pictures they can share with the the zerks for the driveshaft on the 2210? Just bought a new to me 2210 and have greased all the zerks I can see, replaced all filters and fluids, but the more I have read the more I see that the driveshaft lubrication is a problem with...

Not posted for some time... tractor has been behaving itself. Nevertheless after 13 years one of the rear tires (carlisle 26-12-12) has started to crack and needs replacing. I was going to take the whole wheel down to the store to replace it,but I'm having trouble removing the wheel. In the...

I bought a Deere 2210 with the intention of putting a loader on it. The older 210 and 200CX are out of stock. I found on the H130 manual online mentions the 2210 as compatible. But when I called my dealer here in Miami he said that it does not show on his manual as compatible and he e-mailed...

I recently acquired a John Deere 2210 tractor with a 62C mowing deck. But the lift rod is missing and I would like to know if anyone has one of these tractors and a mid mounted deck that can take a picture of the rod system that connects the deck to the 3 point hitch to lower and raise the deck...

2210 jd will not start blows 20 amp fuse when key is in the run position must be a short where to start Thanks

I have a John Deere 2210 tractor that I bought in 2005 with a 62C Mid-Mount Mower. I would like to use the mower again. I used the mower the first year for about 10 hours and then put it in my garage where it has been ever since. The question that I have is about the bell crank, the one I have...

When the snow flies, I remove the 210 loader from my 2210 tractor and store it in the shed until spring (which happens to be the first week of March this year :) .. Over the winter, the lift pistons creep out and the mounting brackets end up on the floor. I then have to jack it up high enough...

I don't know much about front mounted snow blowers for a 2210. Let me start by telling you how my 2210 is laid out. It has a 210 FEL and a 54C mowing deck. It seems to me the front mowing deck attachment is used for the blower mount. I assume the FEL hydro QD ports are used for the blower. Am I...

Hi I have a Deere 2210 Compact Utility Tractor with hydrostatic drive. Mine is the type that has the hydrostatic pedals (forward and reverse) and the lever for high or low gear or neutral. To start the tractor, the lever must be in neutral. The tractor starts fine (in neutral) but when the...

Tractor will not start. When trying to start my Deere 2210 compact utility tractor, it had a slow crank on a known good battery & directly connected to starter/block with good jumpers, etc. Removed starter, bench tested it and it worked fine - but the test, obviously, was not under load...

Greetings all! Just got my first JD equipment. JD2210 and a JD950. The 2210 will turnover, but it won't start. The battery is good and it isn't slow to turnover. Any thoughts? Thank you in advance!

Anyone swapped a suspension seat onto their 2210??? Looking for ideas. Thanks!!!

I have a JD 2210 and the PTO shafts will not turn when I turn on the Power Take off (PTO) Switch. This tractor has two pto shafts, one for a 3 point attachments and one for an mmm. When you use the power take off (PTO) selector lever and select the rear shaft to turn on the mmm shaft will turn...

cancel,cancel,cancel

Morning Gentlemen, Perhaps some of you will be able to help me with my JD2210 as the local Green Dealer has been unsuccessful, though they made lots of money on service-calls. First, I love the JD2210, have had it for 11 years, it has been amazing in what it has accomplished, and I've...

I have a JD 2210 with 54c belly mower and I'm wondering what a good speed to mow at is? I don't know the type of grass, but I keep it about 3-4 inches long and live in Michigan. Any tips on speed would be great. I currently mow in low gear at roughly half speed.

Is there a diagram avalible on the John Deere 2210 tachomitor opperation?

My 2210 has rear end problems. Dealer said it needs a new hydro unit, which I guessing is the whole back end because going to cost over $5,000 to fix. It goes backwards just fine, but struggles going forward. Doesn't bog motor down, acts like its slipping. Any ideas or suggestions on what to...

Morning Gentlemen, I started this post on an ongoing thread, but I think it is perhaps more appropriate to start a new thread. I am about to go from a JD 2210 (newer mdl is 1023E) Green to another color. I love my 2210 and for the most part has done and more than what was needed though the...

Hi everyone. I was just out clearing some snow with the tractor. I drove it into the snow, then pressed the reverse pedal, and as I went to press the forward pedal, it was hard to reach because the pedal had gone all the in the up position and the tractor kept on going in reverse. I tried to...

Does anyone have drawings or installation sheets for a John Deere LVB24981 kit. I would like to know which plug to remove to install the pipe plug and what the supply and return ports are? This kit is also used on the 2305 tractor. John B.

Hi, I have a John Deere 2210 tractor with a 62c mower deck. I only use this tractor for cutting lawns. The 62c mower deck is terrible, its always broken. Is there a good belly mower that can go on this tractor? Thanks Andrew

Hi, I never realized that diesel fuel was so dirty. It was definitely time -or overdue- yesterday to change the fuel filter on my 10 year old 2210. It was BLACK, looked like someone added about a tablespoon of soil to the fuel. Anyways, I guess I forgot that the fuel shut off valve also...

Just want a 2nd opinion on the direction of the piston/rod. I removed them all and marked which cylinder and assumed that the arrow on the piston points to the exhaust, but can't honestly say I verified that before taking them out. I installed new pistons on the rods with new rod bearing. Below...

replacing sleeve and seal clean the area around case before removing the 6 bolts. place a pan under the case to catch the oil that will drain after removing the case. after removing the case pour the small amount of oil thats in the assembly into the pan. take the assembly place it in the...

Recently purchased a used JD 2210 with a FEL and 62" belly mower. I bought this for my wife to use, figuring that a "Good" name like JD and lower time tractor should be pretty reliable for her without me having to work on it all the time. She put a little over 10 hours on it when I borrowed it...

I am looking at a 2004 JD 2210, it has 800 hrs, 210 FEL, comes with 54 belly mower, 47 in PTO driven JD snow blower with hydraulic chute, tire chains and 5ft landscape rake. One owner who took great care of it, they are asking 12,000.00 Does this sound like a good price?

I have had my 2210 for roughly 10 years now, and I love it. Starting last fall before winter, I noticed my tractor has having problems going uphill when the grass was wet from rain. The rear tires would end up spinning, which rarely happened over the past 10 years. Over the winter, I noticed...

I have a JD 2210 and it is currently leaking transmission fluid in the rear just above the PTO shaft. I've looked on JD parts to see if i can get a new gasket or something, but I can't find any gasket for it. I have a feeling i am not looking at the correct part. Can anyone identify where on...

I live in Western Michigan and can't find a place to rent a tiller from, so now i am looking to purchase. I have a JD 2210 and from what i read, the King Kutter TG-48 is a good option from a price and quality perspective. Does anyone use this on a similar tractor? I will probably use it once...

I heard definite grinding the last week when I operated the 4 wheel drive in reverse. Then the front wheels started locking with the rear wheels pulling them. So at first I thought it was the front diff. Since I hadn't changed the front axle oil ever (429 hours). I emptied the gear oil and their...

O.K. so I've searched and searched and can't find anything that will directly replace that punky little 20Amp alternator on my 2210. Here is my own upgrade from the original unit to a very common DELCO 10si 70Amp three pin alternator. *******Disconnect the battery before doing...

im looking for a cylinder head that goes on john deere 2210 used, can anyone direct me on where to find one

I have a John Deere 2210 that I got this past fall. I started using it this winter for snow plowing with the FEL and it works great. I just started noticing a red/pink fluid in the snow if I let it sit for a bit while running. I looked in the rear of the tractor and found the transmission oil...

I have a bit of a quandary. I... a) Ran my 2210 out of fuel for the first time...in a blizzard.:cold: b) I cannot find my service manual, and c) Despite the 2210 allegedly being equipped with "auto-bleed", it does not start after being re-fueled despite lots of cranking. Is auto bleed not so...

I installed two rear lights on my JD 2210 this past fall. I connected them into the pigtail on the rear so they are controlled with the current light switch. Yesterday I was out working on the driveway when all of a sudden the lights shut off. I turned all lights off for about 20 min and...

I have a JD 2210 with a FEL and will be doing some snow removal in the winter. The FEL seems to get in the way of the headlights so I want to add a light or two to the ROPS or somewhere above the headlights, to make snow removal in the early morning possible. Is there an easy work light kit...

I've been sick of my turnbuckle stabilizers since I bought this tractor. Put it on my list to build some telescoping links. The other day the weather was nasty all day so spent the day in the shop. This is what I ended up with. I removed both rear tires but could have gotten by with just...

Hi All, I've got a 260 backhoe I got a great price on, but I still need to purchase the subframe and power beyond hydraulics. I'd like to try and do the installation myself, but so far I've had real trouble finding instructions on how this works. All I have been able to find is the following...

There is a local guy selling a 2004 John Deere 2210 with 210 loader and 54C mower. It has 550 hours on it, and looks great. He is asking $8650 obo. What do you all think a fair price is for this tractor? I tried searching old posts but couldn't find any talking about price. Thanks!

Hi All, One of the attachments that I've wanted to add to my John Deere 2210 SCUT is a John Deere 260 backhoe. Best price I've been able to find for this has been $5500 for the whole package from Mutton Power--and that included freight with lift-gate service. My local dealers were $6000 for...

GREETINGS - FIRST POST --- I HAVE A JD 2210 WITH 400 HOURS ON IT. I USE IT TO MOW, SOME FEL & SOME GRADING. THE TRACTOR RECENTLY STARTED LEAKING HYDRO FLUID AFTER IT WARMS UP. IT LOOKS LIKE IT IS COMING OUT OF A TUBE THAT SITS NOT FAR FROM THE FILL SPOUT FOR THE HYDRO FLUID. IS THIS SOME...

Good afternoon all. I would like to first thank all of those who have contributed to the 2210 repair threads. Great information, pics, part numbers and descriptions. I have learned a lot from your previous experience. Unfortunately I still had to replace my transmission cooling fan and did...

The screw securing the PTO Control Lever has broken. I can still change the PTO selection manually with a wrench, but it's not a "on the move" type of change. This has happened before - I'm a large guy with a large bottom and I think I'm constantly bumping against the lever. I don't want to...

I am anxiously awaiting the delivery of my new (to me) 2005 Deere 2210. Delivery guy #1 that I hired pulled a no-show, so the 400 mile round trip did not happen today (or I would be out just riding around in my yard). I have hired delivery guy #2, and he promises me Friday afternoon.. So...

Hi Everyone-I am new to the forum,but have enjoyed reading and learning from it quite a bit. I am moving up to a new Deere 2520 after a great experience owning and using my 2210, and all of your posts have been highly educational. I really want to thank you all for that. I will provide an...

I need the rear PTO casting for a John Deere 2210 or 2305. My casting is broken inside. Would buy part or whole tractor. Galen

I need the rear PTO housing for my 2210. A housing from a 2305 will also work. Does anyone know wher one might be parted out?

It's EXTREMELY cold here today. I think the coldest it's been since I had this tractor (about five years, but only 240 hours on it). I have a little bucket on the tractor and a little TR3 rake on the back. It's been fine with this setup for a long time and a lot of bad weather. I use it...

Hello all. I really enjoy this forum. Has anybody put an older model sickle mower on a JD 2210 or 2305? What are my limitations, HP, weight, width? I am contemplating buying one but don't want to waste the money. I used to run a No 3 on a JD G growing up but that is a significantly larger...

JD 2210 FEL, 54" MMM, 46" Snowthrower, 54" Snow Blade This replaced my JD 400 Industrial backhoe/loader and 1977 Wheelhorse C-160. Forced to sell the JD 400 by my neighbors who complained that I was storing construction equipment against town ordinance. The 2210 is better suited to my present...

Always worked fine and last night I went to plow snow and they don't come on. 4 ways still work fine. Thinking it is not bulbs since there are two and unlikely they died in unison? What should I do to diagnose ?

I was at my dealership last week and a customer was in there getting his JD2210 fixed after the engine to transmission driveshaft failed from lack of grease. It also broke the front case on the transaxle as it beat itself to death at engine speed after breaking. My tractor has 400 hours on it...

hi i've had a John Deere 2210 for 6 years. i initially got it to snow blow (48" snowblower) my 1000 foot driveway but once i discovered the joys of tractor-dom, i couldn't stop finding tractor worthy tasks. moving wood, rocks, and gravel; raking hay, and driveway maintenance. the bucket seems...

Help, I have a JD 2210 that the Mower Adjustment knob will not stay in place. I have located the culprit which is a spring clip that goes under the tractor and keeps the adjustment cam in place. My problem is where does it hook. I know where it hooks on the frame, because the broken...

Hi everyone. My son was using the tractor today and Told me it was stalling when he was digging out trees. Later on it wouldn't Start. He checked the fuel filter, there was fluid in the sight glass, and when the lights are turned On, they are not bright and go very dimm. I'm thinking now...

Hello everyone. My son went to use the tractor yesterday to cut the lawn. Then went to move some dirt and dig out trees. Told me the tractor would stall when lifting something heavy. He left for lunch then came back and said it didn't start. He checked the fuel filter, was ok, there was oil...

Need to repair the rear 540 PTo on my 05' Deere 2210 SCUT. I know I need some of the internal driveshafts and gears, but beyond that not sure just yet what I need. Looking for used parts, somebody parting one out etc... PM me or e-mail and please let me know what you have, THANKS! Tim -...

I've got a leaking seal on the front axle driveshaft input seal. I got the part on order so I have not seen the part and I have the drive shaft removed so I can see the seal but it's not clear how the seal comes out. Per the manual the instructios are not clear if the seal can be replaced...

Hydraulic fluid has dripped from my mid-PTO shaft and emptied the reservoir; well, at least no fluid is visible in the window, and the drips have stopped. Based on all my Internet research it appears my mid-PTO seal needs to be replaced. The million dollar question is can I replace the seal...

Hello everyone. I'm trying to help repair a starting problem on a 2210 compact tractor. The battery keeps going down and that is probably the problem. However, I checked the voltage coming from the alternator and one spade reads 3.4 and the other 3.6. I understand this is AC voltage and is...

Hi I noticed a couple 2210's at the dealer with around the same hours as mine - around 700 - and they both had a lot of free play in the steering wheel, the worse one had about 1/8 turn of freeplay!!! I've noticed about 1/8 inch of play in mine, hardly anything. What's the deal with the two...

Guys I have a friend of a friend thats selling a 2004 2210 with FEL and ballast box with 350 hours on it for $6500 but the PTO doesnt work. The owner said his brother his a rock with the brush hog and the PTO doesnt work anymore. Im looking for a cheap tractor and wondering how bad of a repair...

When i pull up on the yellow knob the pto clutch seems to slip

Hi Everybody.. Last time I was here was about 8 years ago when I was purchasing my very first SCUT and you all were very, very helpful and I ultimately selected the JD Mdl 2210 w/ FEL, 56C and Front Blade over a Kubota. And until yesterday I was extremely happy with the 2210 - as it did...

New to the site, hope someone can help. I purchased a JD 2210 with a front snow blower. Throws shear pins to beat the band. If I have it in float mode and the blower goes lower than the front wheels, I get a terrible vibration. Also happens if I don't use float and put some weight on the...

According to the 2210 oem parts on line you only could buy a whole new front axle differential for app.$900. A mechanic at the dealer checked the service manager OEM part screen and surprisingly, even to them,you can get all internal parts for this differential separately. we heard a knocking...

Hey All, Anyone ever had an oil pan leak on a JD 2210? Do I need to pull the motor to fix this? I can get all the bolts off, but not sure if the oil sump will keep me from getting the pan off with out lifting the engine?? Thank!

My John Deere 2210 just died yesterday ...its never had a problem... but it died and refused to start a couple of times when it was in gear, but started up ok in neutral...then it just died completely and I can get nothing from it. No fuses blown, battery terminals are clean and everything...

Problem: when turning tractor in sharp turns heard thumping noise from front axle differential and put it on work bench. By turning the shaft axles there is some play lengthwise (so towards shaft axles) in the carrier. The differential is a fixed unit with no adjustment ( that's why you buy a...

Thank you all for setting up these forums. Since 2004 owner of a JD 2210 in eastern Colorado near Denver, trying to maintain weeds and some grass on 2 1/2 acres with the compact 2210. Found out over the years that it's hard for a (finishing)54 inch belly mower even on the highest setting to mow...

I looked at a JD 2210 with a belly mower and FEL, 256 hours, 2006 at a dealer. Asking price is $10,200. Any opinions on the tractor and price? Also, I could not find what the bucket is rated for and would appreciate any input anyone might have on this. The tractor is clean as a whistle with not...

Bones72

S $11000 forJD2210 a reasonable price with FEL, 62 in. MMM, and a front mounted snow blower with 200 Hours ? Bones72

Is $11000 for 2210, with 200 hrs, FEL, 62 in. MMM, and front mount snow blower a reasonable buy? Bones 72?

What year was 2210 last Manufactured? Bones72

I have owned one for 6 years and love it! My Dad has owned two kubota's over the last 16 years and just bought his first John Deere. Praise the Lord anotherone came home! thanks JC

Hi All, I've got a John Deere 2210 and I've got a (barely) used 210 loader that I'm considering purchasing from a dealer up in New York. I would have to get it delivered via freight carrier. It's missing the subframe (mounting brackets) and hood guard, but it looks like I can get those from...

If you want the new 54" blower to put on a 2210 it clearly states that is will NOT fit the 2210. I could not figure this out, so I ordered one from my john deere dealer anyway. The next day the dealer called me back to tell me the order was kicked out of the system because the 54" blower would...

my JD 2210 it has done all and more for me, I just love it. It has less than 700 hours on it and I have been faithful on maintenance. Over the last two weeks I have noticed a vibration from the engine. I say engine because I have eliminated drive train and mower deck. I can be sitting still...

well not so much lift issues, but lowering to the varrious heights on the lift scale. For instance , it lifts all the way and lowers all the way but the settings inbetween, for 2 -3-4 inch does not seem to "catch" I can't figure out how the cog system works, mine spins freely 360 degrees, any...

Looking to trouble shoot my JD2210 compact which is leaking a bunch of hydrualic fluid up the steering column. Anyone have repair advice? How difficult of a fix is it for a do-it -yourself job?

Well guys, I've done all I know to do with my tractor! Problem is it won't start, I thought the battery went south on me, but it's fine! How it began was I went to mow the grass and it wouldnt start, so I jumped it with my truck and it fired right up, so ok I continued to mow my grass...

Hello everyone. Great resource for owners or new to fluid Power! my 2210 is a backsaver. 60" mmm no loader Yet! $7200 with 808 hours so far so good! A little freaked about hydro filter location and transmission fan! More soon!

I have a 2004 JD 2210 Utility Tractor. Having problems with what I thought was the regulator. 1 - New battery = 12.86 VDC with no load 2 - When started, battery test at 12.75 VDC whoile running 3 - Alternator looks OK and tests at 29 to 64 VAC when running. 4 - When alternator cable unplugged...

Is there a trick to getting the rear axle off to replace the seal? There are two bolts that I can't get to without taking the transmission out!

Anybody using rim guard in the rear tires for ballest on a 2210? Thanks

i have a 2210 getting slower in low gear. use to run about 5 miles an hour (example) now run about 1 mile an hour example almost wants to stop. runs fine in high gear 500 hours changed transmission fluid & filter

I recently finished building a cab for my 2210 and am in the process of making my own heater using a chevette heater core and a 130cfm dc muffin fan. Myy question is how or where do i tap into coolant lines? I see where curtis cabs uses a sending unit adaptor but since I didn't ordder their...

After pricing cabs I quickly decided the only way I would ever be able to afford the luxury of snow-removal without fighting the elements was by fab'n my own. So about a month ago I got serious and started scouring this site and google for other cab builds when I stumbled upon Huskerplowboy's...

My blinkers just stick on. They come on with the key, and stay on regardless of any turn signal switch or light switch position. Occasionally I can get one or the other to turn off, or blink a few times, then it wedges again. The local dealer suggested a new module: LVU800247. That's a $70...

Hi. I am new to the website and have a question regarding my recent purchase of a 2005 JD 2210. I would like to add a 12 volt receptacle to power a pull-behind sprayer. I was wondering if anyone out there had added this to their 2210. If so, my questions are: a) What brand of 12 volt...

I would like to have a grapple for my 2210. I could build the grapple, thanks to the ones that I have seen on here. :thumbsup: My problem is figuring out the hydraulics. Do I just "T" in to what I have with another valve, or would I have to set up something differently? Any help would be...

My 2210 just turned 200 hours, so I am getting read to change the transmission hydro fluid, the front axle gear oil, the fuel filter, and the oil. The tractor is six years old; I am the second owner. The antifreeze tester still shows five "balls" floating in the tube and a low temp of -30...

Had a little seeding job to do so dragged out the ole tandem disc. The JD2210 didn't seem to mind too bad. It worked better after I built a weight rack and added 250lbs. ;)

My JD 2210 compact utility tractor will not start? When I turn the key with the shifter in neutral the dash lights come on and I hear a single click. The starter does not engage. I have had the battery and starter tested off the tractor. I have also tried all the Operator Manual safety switch...

it's 2004 2210 i was pushing stone for about 2 hours tractor was getting pretty warm and the pedal faded away,the tractor still moves but not very well oil in trans gets very hot, i had a u joint go bad and i tore it down replaced joint and started checking valves around pump and rearend there...

My 2210 with 600 Hrs shut off yesterday and will not start. I had been running it various time through out the day with no issue and now there seems to be an issue with something not letting it try and start. I got it to start at about 930 PM and went and dumped a final load with the FEL. I...

After replacing the hydraulic steering ram and changing all the filters I hooked up my brush mower and discovered the rear PTO will not turn on. The fluid sight-glass in the rear shows appropriate level and the bucket/steering work fine. Checked the PTO selector lever (to the left of the seat)...

My John Deere 2210 has had a small fluid leak out of the power steering hydraulic unit. Now it has gotten worse and I need to repair it-just as the grass is getting out of hand! Has anyone done this repair? I'm also looking at the shaft that goes into the hydraulic unit on the left side and...

Any common problems 52 in deck has been working fine for 120 hours and turn to 6 inch high and now won't turn to lower deck. Not hit nothing,pulled 4 ft disc in garden and now time to mow, any ideas, owner manual not much help,

I have a 2005 JD 2210 with 130 hours. Comes with an "Edge 62" belly mower and a 200X quick detachable loader. Excellent condition, garage kept. What is it worth in a private party sale?

I just finished wiring in some LED lights to the ROPS of my tractor. I used a 20A fused lit switch hooked to the + of the battery. My question is can the lit switch drain my battery down if it is lit all the time even when the tractor isn't running? My thoughts were yes and I pulled it out...

Is there a kit that I can add to my JD2210 that will lift the deck independently from the 3pt??? Seems I've heard of that??? I'm tired of running my 3pt arms in the ground when the deck is down. Thanks in advance!!! :)

HELP!! I own a JD 2210 with a 47" snowblower (front ount). I have a couple of issues. I find it extremely noisy, like a rattling noise, when blowing light snow and operating at about 2900 rpm. does anyone else have this problem? Also, my dealer could not tell me which way the driveshat that...

I have a JD 2210 on which I installed the power beyond kit in August 2008 to supply hydraulics for the backhoe attachment I purchased. The backhoe was on the tractor since then, last week I removed the backhoe & hooked up my backblade to plow snow. My problem is: when I raise the backblade, the...

Hello all, Sorry for the repost, but my previous post earlier today has disappeared. I am hoping you can give me some ideas where to look for the vibration noise I am getting. Here is the senario; JD 2210, yanmar engine 3TNE74, curtis cab, 47 inch snowblower. I thought maybe it was the PTO...

Curious if this adapter will work on my 2210 Deere? https://www.imcuniverse.com/store/easychange.htm

Now that we've had 2' of snow, I'm thinking it's time to invest in a snow plow for my JD 2210 CUT. The FEL / bucket did a decent job but the plow would have made the job easier. Is the JD front snow plow assembly 54" or 60"? Is it a quick connect setup like the FEL?

Both are used. Here's all I know so far: Deere: 4WD 62C mower deck, 300 hrs, Hydro. $7,900 Kubota: 4WD 60" RCK60B Mower deck, 431 hours, Hydro. $6,900 Dealer claims Deere tach was replaced at 289 hours and currently shows 300 hours. Gives me a bit of a bad feeling.... Both are in nice...

I have purchased a used JD 2210 with FEL, Box Blade, and 54 C Belly Mower. I have a manual for the tractor but not for the Belly Mower. I want to remove the Belly Mower to service the tractor and do whatever lubrication is needed for the mower. I can see the side pins which need to be...

Hi guys, I purchased a used JD 2210 in March '08, and it's done everything I've asked of it and more. Recently I decided I'd like to measure the hydraulic pressure to the FEL just to see if it's putting out the pressure it should. There was no other reason (no lack of lifting power, etc.) - just...

Anyone guide me to a detailed thread concerning replacing the HST cooling fan on my JD2210?? Thanks in advance for any help!!! :)

When the JD BH first came out for the 2210, I bought it and with it came a swivel seat. It is a pain to swivel. Has anyone found a better swivel seat for this combo?

Greetings, I have a 2004 John Deere 2210 with 275 hrs. I use the machine for all sorts of light yard work as well as mowing. Recently I had an emergency incident that required the brakes to work on a very steep hill. Previously,I had only ever used the brakes as a parking brake. The...

I need to replace the leaking battery on my Deere 2210.. today. Being Sunday, the local dealers are closed. I need to get to the auto parts store but need a battery part number.. which I cannot find anywhere on the 'net! Anyone have a cross reference battery number for a 2210?

2003 model, 210 Loader, 4x4, 706 hrs. Whats it worth?

Just bought this tractor from a guy. He said the pto quit working about a year ago. Its a 2003 with 706 hrs on it. Any ideas on where i can start?

Hello, New to T.B.N. I have the opportunity to purchase a 2003 John Deere 2210 with a 210 front end loader for $8,599 from a local dealer here in Wisconsin, delivery included. There are a few minor scratches but no dents or dings on it. The paint looks great except for two dime size surface...

I just purchased this tractor. I got a mower deck 62" without any kind of mounting brackets. Anyone know or have a picture of what I may need to hook this up?

Hydraulic 5' blower on a JD 2210? I've got a chance to get a 5' hydraulic blower for a decent price, that was designed for a skid-steer. I'd like to convert it to run on my CUT. I'm thinking that I can put a PTO driven hydraulic pump on my mid PTO, along with a PRV, then install a...

I just got a used 2210. While I think it is the right size/style tractor for me, the grungy appearance bothers me. The last owner did not take very good care of it. Paint is chalked, decals are faded, some scratches that are rusting on the hood, etc. Concrete in the bucket and splashed on the...

Got a chance to buy a 05 - 06 JD 2210 4x4 for 12 gees with 100 hrs. Includes -60" belly mower -Quick attach front loader w/ 5' bucket -Post hole auger w/ 12" bit -60" rock/landscape rake -48" roto-tiller -48" Farmall bush hog -Quick Hitch Price seems good but I've noticed a lot of these for sale...

This afternoon I picked up the iMatch and ordered the Femco Folding ROPS for my 2210. I installed the iMatch this evening and it was worth every penny. I do not know how people get alone with out one! The Femoc ROPS should be in by mid next week the dealer tells me. Anyone had any luck...

For grins I decided to check the hydraulic pressure on my new to me JD2210 and was supprised to consistently get 2400 psi compared to the manuals 1987psi. I used a 4k psi gage mounted to a quick coupler and connected it to the SCV after I disconnected one of the loader lines. The pressure was...

I am looking to purchase my first compact tractor. I have found a 2005 JD 2210 with 108 hours, 200CX FEL and 54" MMM. The 2210 is in perfect condition and looks like the guy never used it. Does $10,000 seem fair?

The local Cub dealer had a pair of CubYanmar sc2400's on display out front each complete with mower and loader. I didn't ask price, just for yucks took a peek. There are a lot of nice features on that bumblebee that JD maybe shoulda thunk of. Number one feature is the shiftonthefly tranny...

I have JD 2210 Gas with a 54" Deck and fron loader, wheel weights, as well as the weights on the back - In very good shape, always in my shop, never sat out It is a 2000 with 500 hours, I purchased this back in 2001 with 60 hours. I am considering selling it and I have no clue what it is...

Hi All: Its been guite a while since I've been on (2.5yrs actually). In any event, I was running my 2210 over some brush today and ground up my transmission fan. I went down the road to my dealer and purchased a new fan. However, unless I am missing something, this looks like a major pain to...

Can anyone answer as to how fast in MPH the JD 2210 will travel in high gear on the road for transporation purposes. Thanks.

Hey, I'm seriously looking at selling my JD 2210 now. We've been talking about it for awhile now and getting serious now. Its just not big enough for what I'm doing. Its a 2005 with 136 hours. I've got a curtis hardsided cab, heater, the console w/ cd player and defroster, 2 front 2 back work...

Hey everyone, I've got a John Deere 2210 that we mostly use primarily for its loader capabilities on our paved parking lots. So the tire wear on my turf tires has become excessive and it is time for new tires before the snow flys. Since the tractor is never used on turf I would like to go to...

I have viewed this site for a long time and recently became a member. Anyway, I have not been able to find an post on outfitting a Femco weatherbrake onto a 2210. I am interested in purchasing one for this winter when using my 47" snow blower. I want something that will block the wind...

First post, great web site. A problem arose last week on my 2210, the blinkers on the roll bar are now on all the time regardless of the position of the master switch or the position of the blinker toggle switch. Are any wiring schematice available on line? Any possibilities of the cause...

Having gone from my 2210 to a 2520 and then back to a 2305... I thought I'd post some of my thoughts on the machines.... I sold my 2520 about a month ago. For those who followed my ad's, I sold it for $16,250... if curious ( I would be ) I also attached a few pics which can be found here...

Hi to all and hope you can help me. My friends 2210 recently started to smoke at the 3000 rpm mark which is where he has to run it for mowing and snowblowing. The fuel filter,oil filter,and air filter were changed when he put the snowblower on around Nov 1. He uses the JD oil and the last 3 or...

On John Deere's website, the survey suggests a 2210 would be ideal for my use. (Mowing an acre, plowing snow on a long drive, spreader from the 3-point hitch, etc.) Does anyone have any experience on how well the MMM 62" cuts? I am looking for a very nice, smooth cut on a very visible lawn...

Just wondering where owner have mounted aux. switches on there John Deere 2210? I am going to mount 1-2 lights on the rollbar and 1 back-up light on the back Thanks, Dan

Has anyone ever hooked something like a tiller from a Kubota B-21 to a JD2210? I can get a hold of one but I don't know if the PTO shaft is going to be the right length. Before I haul my tractor over there or the tiller here to try it I'd like to get any comments from this forum.

Anyone know where you can get replacement front tire for JD 2210. I had the dealer deliver the tractor with Carlisle R4s (industrial). I tore up a front tire and need a replacement. Dealer claims he can't get them.

I'd like to put a grapple on my 2210 and was wondering about my options. Is adding a 3rd scv possible on this unit? Is there someone who builds them or should I design my own?

Thinking about a 42" or 48" rotary cutter for my JD 2210. Would like some feedback on your experiences including weight issues, 3-point hitch issues etc. Considering the JD LX4, Woods RCC42 or Woods Brushbull 48 or any others. JD 2210, 49" CX200 FEL, 54" MMM, 47" Snowblower, 54" Front Blade...

Recent new lurker to the forum. I have a 2210 and will be buying a 48" tiller. Either a JD or KK, trying to decide if it is worth $600 more for the JD. Either way, I understand that the PTO shaft will need to be cut. What I don't know is how much. How do you determine this. Any assistance...

Is there any market on finding good or excellent Front End Loaders for 2210 JD Tractors , and do they ever come down in price for new ones ? I was quoted $3,500.00 for a new one that comes on and goes off easy ? Seems a little steep ? Thank you in advance . gas1968@verizon.net

I have been told by 800 number, in the small give away manual, that the charge is $ 75.00 for the Actual Shop Service Manual for my 2210 JD Tractor ? Does anyone know where I might get it a little cheaper , say $ 50.00 maximum ? gas1968@verizon.net

Anyone get a Cruise Control kit installed on their JD2305? Could it also be put on a JD2210? Thanx, Dave.

I converted a JD 47" 2-stage from a 318/420/430 to my 2210. Long story short I bought the snowblower with the intention of converting it for my F911 but that didn't work out. Although I've wanted a snowblower for some time I just couldn't justify the total cost. This one complete was about a...

I have a friend wanting to sell his JD 2210 with 210 loader, bucket, 62C mid mount deck, imatch, LX-4, box blade - 150 hours. He wants a cab tractor now (too hot in Texas). How much is it worth? $10K? Anybody interested? It is in the Dallas, Texas area and delivery could be arranged...

Found this on Ebay... http://cgi.ebay.com/John-Deere-2210-Tractor-w-Loader_W0QQitemZ7573153334QQcategoryZ63988QQrdZ1QQcmdZViewItem

JD 2210 and Jinma 6\" chipper - questions Is it possible (or adviseable) to run the Jinma 6" chipper from a JD 2210 or JD 2305? The 2210 is 23hp with 17.7hp at the PTO @ 3000 RPM's. It has a Cat 1 3-point - not sure of the lift capacity. The 2305 is a 24hp with 18hp at the PTO @ 3000 RPM's...

Would use strickly for snow removal... curious if the 5' or 6' blade will rotate all the way around without detaching?? Thanks guys!

I just finished the web page about the Optima battery I installed for my JD 2210 in Sept. If you are thinking about install this battery then check out this web page. :-) On the main menu click the John Deere link.

I finally got some time to do the web page for the block heater I install in Sept. If you need some information and pictures about install block heater for JD 2210 Check this web page out. :-) Under the main menu click the John Deere link.

Winter is here and I am thinking of a cab for my 2210. What have you other 2210 owners purchased? Can you attach pictures of your cabs? I just don't know how much money I am willing to spend. Since I can not just go to the dealer and look at them, I need your help. Let me know what you can.

Dose any one know if it is possible on the 2210 to add hydro lines to the fel for a grapple bucket? In addition what is the lift capicity of the 3pt hitch on the 2210 in lbs? thanks

Hi, I live in central Michigan, and am looking to replace my JD318 and Ford 8n with a CUT. Been looking at the JD2210, but wondering if a good used 4100-4300 might be better. I have about 5 acres, currently mow 2, would like to mow 3-4, and brush hog the rest. Also will use for snow removal...

Spec\'s of the a 200CX loader on a JD 2210? Does anyone know what the lift Height and weight is for the 200CX? The manual doesn't give any spec's Thank you Jim

Has anyone had any issues with their oil light coming on a start up? I know this engine is in a lot of John Deere equipment so anyone with this engine can answer this; 4010, 4115, 4210.... When I start my 2210, the oil light comes on for a split second to 1-2 seconds (different every time). I...

Hi all, This post is somewhat in response to Iowa2210's problem with his MFWD axle. Although he only had 20 hours on his machine and hadn't used his in the winter, I was talking to another poster and 2210 owner, and he urged me to change my axle fluid at 100 hrs. due to the fact that I operate...

I'm looking for a tractor to mow about 4 acres of lawn and move a little snow around. I've been considering the JD 2210 and the Bota 7610. Both tractors look similar on paper, with Kubota having larger wheels and 1 more hp. I drove both and both seem like they would do the job. Both dealers...