john deere 1050

I recently had to split my JD 1050 tractor to replace some seals in the transmission & PTO shafts. Although I ended up not replacing my clutch (it measured out okay)... I did buy the special tool (JDG-52) to adjust the clutch fingers for $99 (ouch)! I've seen a few posts asking for the...

I recently had to split my John Deere 1050 into three pieces to replace two seals in the clutch input shafts. What a job! When I went to the John Deere dealership to buy new hydraulic fluid, I was about to pick up regular Hy-Gard but the man behind the counter said, "Wait! You need to use Low...

In an effort to free up a frozen brake on the left rear wheel over the winter, I apparently lost the drive on the left rear. The right rear only drives when the differential lock peddle is enguaged. I have started to disassemble to gain access to the axle housing but have not removed it yet...

We've got a 1985 John Deere 850 with a 75 loader, but my dad's "Holy Grail" tractor is a 1050. We found a 1985 JD 1050 for sale with an 80 loader and not only does it look more rugged and stout than the 75, the spec sheet also shows this, too. Except for one important category: lift capacity...

I have a 1984 John Deere 1050. This is my first tractor so I am in a learning curve to say the least. I have purchased a model 75 loader to add to it. I want to use a 2 spool aftermarket control valve. My tractor did not come with any hydraulics other than the factory ones for the rear lift. I...

I'm the proud new owner of a JD 1050, 4x4, 1986, with a nice big round hole in the left side of the crankcase. Threw a rod. Probably a two or three inch diameter hole, below the front cylinder. I've been advised to just get a working, used, 3T90T-J to swap in, but I was wondering whether there...

I have a JD 1050 (I believe it is 20 + years old) with a 3-cylincer Yanmar engine. The JD dealer replace the fuel injector pump (that I bought) and now wants to 'clean' the injectors. The estimate he game me seems way too high. Does anyone know how many hours it would take to install the three...

To make it quick: I saw burned motor oil spraying out of an overflow rubber tube coming from the area of the fuel injectors. I turned it off and wanted to check the oil level. As soon as I took off the cap, the oil came out like tilting a gallon jug on the side at once, a jet 3-4 inch long and...

Does anyone know whether a Dry Hydraulics Water Absorber product can fit, and be used with a JD 1050 tractor with loader?

I have been researching and working on a JD 1050 hydraulics for 3 months. Who is the best hydraulic repair shop near Oklahoma City?

John Deere 1050 Hydraulic 3 Pt Hitch hangs up or down. This tractor has no attachments yet or no power steering. The 3 Pt Hitch will go either way after it is sitting (not running) and will go up or down, then lock up again. My initial rookie mistake (lower Alabama old codger) was when I put...

I posted earlier about my 1050 that wouldn't move because the something was keeping the rear wheels from turning. Someone suggested that it might be locked brakes. Evidently, this is a common occurrence with this model. The tractor gets run very seldom and sits in a barn with the door open...

My 1050 will not move. The rear wheels are locked up. For awhile, the wheels would hangup as I let out the clutch, then give a little "pop" and the tractor would drive and shift, etc. Now --- locked up tight. Any thoughts on what is the matter? Thanks. Dave in KY

I have just purchased a John Deere 1050 2wd. The brake peddle has full travel but does not engage the brakes. I am going to buy a brake kit from Hoye tractor parts. Has any one done this job? I have taken lots of cars apart but never a tractor. Don't what to bite off more than I can chew. Thanks...

If anyone is looking, I just listed mine in the for sale section. Thanks,

I have a mid 80’s JD1050, 4x4, 37 HP Yanmar turbo diesel, with 3006 hours on it. Overall average condition, just had the fuel injection pump rebuilt last week. Engine runs great, going in to the shop next week for a rear axle seal leak. The tractor has the typical scuffs, etc. for a this...

I just had to have my JD 1050 injection pump rebuilt, 3000 hours and it apparently was worn out. $668 later it was running like a top.

Thanks everyone. Like a asid I have a 1987 jd 1050 with fel without power steering. It was plummed it as listed below. 1.From the pump they cut the little line and sweated some fittings in. From the pump goes to the bottom of what I can guess is a pressure regulator line to the bottom of it. 2...

Thanks everyone. Like a asid I have a 1987 jd 1050 with fel without power steering. It was plummed it as listed below. 1.From the pump they cut the little line and sweated some fittings in. From the pump goes to the bottom of what I can guess is a pressure regulator line to the bottom of it. 2...

Symptom 1: with the bucket flat down, 1 inch from the ground, if i try to get under a pile of snow or sand, the bucket will start lifting upward. I cannot get it to stay flat. Symptom 2: let's say I raise the loader half way and I flip the bucket downward all the way. The goal is to 'cut' a...

Symptom 1: with the bucket flat down, 1 inch from the ground, if i try to get under a pile of snow or sand, the bucket will start lifting upward. I cannot get it to stay flat. Symptom 2: let's say I raise the loader half way and I flip the bucket downward all the way. The goal is to 'cut' a...

Symptom 1: with the bucket flat down, 1 inch from the ground, if i try to get under a pile of snow or sand, the bucket will start lifting upward. I cannot get it to stay flat. Symptom 2: let's say I raise the loader half way and I flip the bucket downward all the way. The goal is to 'cut' a...

When I try to grab a pile of sand or snow I put the bucket down an inch above ground, but as I move forward, the bucket begins to tilt upwards and doesn't pick up anything. 2) If i lift the loader all the way up, and then turn the bucket to unload, the buckets dangles instead of being firm...

My 1050 is experiencing hydraulic problems and I need some advice. Currently at a Deere repair center but they are having trouble sourcing original parts. If they cannot source oriiginal parts they will not use aftermarket parts. If it gets to that point I am bringing it home and then looking...

My 1050 is experiencing hydraulic problems and I need some advice. Currently at a Deere repair center but they are having trouble sourcing original parts. If they cannot source oriiginal parts they will not use aftermarket parts. If it gets to that point I am bringing it home and then looking...

My 1050 is experiencing hydraulic problems and I need some advice. Currently at a Deere repair center but they are having trouble sourcing original parts. If they cannot source oriiginal parts they will not use aftermarket parts. If it gets to that point I am bringing it home and then looking...

Over the years my starter has occasionally responded with just a click. My rebuilder attributed this to low voltage, so I installed a relay. The problem just recurred, and I discovered that with key turned to start, there is no juice to the relay. Assuming a switch problem I subsequently...

Hey all, We are putting back into service a small (5 acre) farm that had long been disused, much of which is quite overgrown. I know some of the small farms here seem to be more horse-oriented, but what we have in mind is more of a homestead. Currently I have a JD 112, which I keep because it...

My clutch peal seems decoupled from clutch. I have had this apart before, and it had a sheared drift pin that holds the outside to the inside shafts together. I very much suspect hat this has happened again. Any suggestions how to fix? Do I need to split the tractor in order to get to this pin?

We've recently bought some pretty hilly, mostly wooded land. We have several "green fields." I'd say total of 12 acres but plan to clear more land over the years. We are about to buy a 1980 John Deere 1050. It's four wheel drive, with a bucket. It has just over 2,000hrs. Only two owners and the...

The Warning Lights on my JD1050 do not work. By warning lights I mean Oil Pressure, Temperature, and Alternator. Since none of them have ever worked for me I thought it might be a common problem for all three. I have tried to read a schematic but am pretty much lost as to how to use it. Is there...

My IT shop manual does not have a wiring diagram, and a Google search returns TMI, and what might be pertinent is not readable. Does anyone know where I can get a correct, legible 1050 wiring diagram on-line? My starter has a dead spot, and the rebuild shop has asked if there is a relay ahead...

Last weekend I purchased a John Deere 1050 tractor with loader. This is my first tractor of my own, however I grew up around farm equipment. After purchasing I flushed the transmission case and filled with fresh JD Hygard Low Viscosity oil, cleaned the filter screen, renewed the spin on, renewed...

somewhat recently i purchased a deere 1050 with a bit over 2000 hrs on it, motor was rebuilt by a well regarded mechanic around here, she runs great but has a few maintenance items i have to replace like the brakes, clutch in a couple years, and the front axles bearings. my concern and...

Hello all after reading many posts on here i finally decided this was the forum to join. Some what recently i acquired a later model 1050 4wd and it is in contradictory to say but shes in good shape, and then other point shes in need of replacement, wheel bearings, pinion seal done right...

Hi everyone, new to the forum, and new to hydraulics. I'd like to run an implement (a gregoire DX-20 leafer) off of a Deere 1050. The pump output etc is all well within spec (for gpm+psi), but unfortunately the 1050 has no additional ports / quick disconnects available. I guess the...

Hello: I am having the following issues with my john deere 1050. The timeline is as follows: When I bought the tractor, the hydraulics were jerky. More so with the john deere 75 loader and less so with the 3 point. A mechanic came out and drained the hydraulic fluid, replaced the...

Hello, Has anyone installed the heating element in the transmission/hydraulic heater in a John Deere 1050? I was wondering if the cap with the hole is the same as the cap without, except for the hole? My idea is drill and tap the existing cap to install the element or use a weld on fitting...

I have had on-again, off-again problems with the hydraulics on my JD1050. Honestly, if I didn't have as much invested as I do at this point, I'd probably replace it (which I may end up needing to do anyway) if it wouldn't cost me an arm and a leg. The problem I am encountering now is my...

Ok so I was having a heck of a time tryin to figure out how to hook up my joystick controller on my JD 1050 with jD fel. But I finally got it it was the pby plug missing an o ring. Now I haven稚 ran it much maybe a couple of hours since the fix. Well about a week or so ago I started bush hogging...

i recently bought a john deere 1050 tractor and i know the previous owner very well and remember when he bought it. the tractor has a john deere 80 loader. everything worked like it should now here is the problem. he wanted to add a joystick control instead of the 2 lever set up it had before...

Hello all, I have a John Deere 1050 which I am trying to diagnose coolant loss. Sorry for the long post. After operating at temperature and letting the tractor cool down, the coolant overflow bottle loses about 2" worth of coolant every time. In other words, it's about 2" lower than before...

Can anyone identify the electrical connector in these pictures and recommend a source to purchase the connector from? I'm redoing the electrical wiring on my John Deere 1050 and this connector goes into the starter motor. It is in okay shape but I'd prefer to replace it with new with the new...

Can anyone tell me if the front end of a 1070 would fit the front end of a 1050. They are both 4 wheel drive. The 1050 hub and spindle need replacing.

I have a friend that just bought a JD 1050 with an engine problem. The tractor will idle but when the throttle is advanced to about 1200 rpm's it rattles, blows lots of black smoke and quits. The 1050 is a turbocharged tractor. Things done to date: 1) Injectors checked by qualified shop and...

JD 1050 (Yanmar early model) that was recently acquired has a hydraulic issue that I need help with. It has a loader and a grader blade on the 3pt. At 1000rpm the loader will hesitate for 6-15sec before it will start to move, and it is slow when it does. To get decent lift rate it has to be...

Have an early model JD 1050(Yanmar) worth an hydraulic issue. Tractor was recently acquired work the problem; loader slow to respond and raise, 3pt very slow to respond and raises in 2" jumps(at the rear blade), unless the lever is fully raised then it is smooth. Has 1126hrs, new hyd filter...

Hi I'm looking for a hydraulic screen for my John Deere 1050. I have no idea of the year of it because the previous owner backed into stuff repeatedly apparently and completely made the serial number plate unreadable. From what I see on the web I think I have the screen with the John Deere part...

I have a John Deere 1050 with a Model 8 backhoe. I went on the JD parts web and looked up the following part that is stripped (previous owner cross-threaded it). I looked online for the part and found it, but have no way to identify if this is the correct part. Here's the part # info followed...

I have a John Deere 1050 and the rear hydraulic lift is jerky. If you ease the lift arm up the lift doesn't do anything for a few inches then it jumps up. Is this an adjustment I can try? If so , where is the adjustment? Thanks

I recently purchased a 1050. The person I bough it from replaced the starter. In the mean time, all of the wiring was disconnected except for the key switch, battery, and starter. I started reworking all of it and found out my light switch CH18036 does not work. Can anyone tell me what all this...

Hi all, First off, this is my first post and first time working on tractors. I have worked on my Ram 2500 diesel truck. :thumbsup: I just bought a John Deere 1050 with a Woods LC108 loader. It starts right up with no blow-by that I can see... no pressure to speak of from the crankcase breather...

Neighbor's 1050 was leaking at front spindle seal. On disassembly there appears to be wear on the seals mating surface. Wondering if this is a wear "sleeve" which can be replaced easily. It looks like one, but not shown on JD parts online and it did not move when tapped lightly.

I'm replacing the clutch in my John Deere 1050 4wd tractor. I ordered a new clutch from Yesterday's Tractors and now I need to adjust the clutch fingers, or the clutch release lever height. The manual specifies a special tool, a JDG-52 Clutch adjusting tool. In the photo below "A" is the special...

The idiot lights on my John Deere 1050 do not work. What is the proper way to get to them in order troubleshoot or replace them? Do I need to remove sheet Metal?

I'm hoping someone might be able to help me out. My father has a JD 1050 but the wiring harness isn't in the best shape. I asked the local JD dealer if they could get me a copy of the wiring diagram. All they provided me was the parts sheet that shows the wiring harness. I want to fix the...

Greetings again folks, Many folks, myself included, have experience sluggish hydraulics on our pre -11000 Deere 1050's. I found an interesting thread here from a gentlemen with a similar issue; his solution, based on feedback from the dealer, was to replace the filter with a piece of 7/8" ID...

Can anyone tell me the tire/wheel size combos for a John Deere 1050 4x4 Tractor? I have AG tires on it now but I want to get Turf or R4 for it. Tractor Data shows the tires as: Ag front: 6.00-16 Ag rear: 13.6-28 I'm pretty sure the fronts that are on it are 8" though...

Just wondering what the original OE 1985 Deere Backhoe model would be for this tractor... I came across something that said it could be a 1550

I have a 1986 John Deere 1050. When lowering or raising the 3pt hitch it will not stop at the desired height. To explain further; if I raise the lever, it will continue to raise to max height unless I bump the lever down about half an inch. Once I do that the attachment will stay in place. When...

I have a 1986 John Deere 1050. When lowering or raising the 3pt hitch it will not stop at the desired height. To explain further; if I raise the lever, it will continue to raise to max height unless I bump the lever down about half an inch. Once I do that the attachment will stay in place...

Looking for a drawbar. No longer available as original equipment. Nothing on ebay. Could perhaps make one myself but don't know the material, dimensions or tempering. If anyone knows of where to get one or where I might find specs, it would be appreciated.

I have been trying for a week to find a solution to this problem that I have never encountered before. 1987 John Deere 1050 will not start with a brand new battery. Before I try turning the key, my oil indicator light comes on, my headlights and flashers work - battery reads 12.8 volts. Once I...

Hello All, I am new to working on machines myself but have been working on cars for some time. I have a John Deere 1050 late 70's early 80's tractor. I currently have two leaks and looking to see how difficult it would be to do this work myself. Below I've attached an image of where the leaks...

Hello, I recently bought this JD1050. (Love it by the way) When I bought it a couple weeks back the shifter worked fine. (it's a "bent shifter" by design) Then one day as I was shifting, now the shifter spins. It still shifts fine, but it makes it harder to find gears because it spins in my...

As mentioned in the title I'm looking at options for a disc harrow for my John Deere 1050. I currently farm about 2 acres of sweet corn and am looking to upgrade from my old dual gang pull behind disc to something that is three point mounted. The ground is mostly clay and is terrible to work in...

I recently developed an issue with my 1050's lift. The arms hadn't been used in about a month, has been hooked to the feed mill. I went to use the spreader this week and now It will either go all way up or all the way down, doesn't have an in between so to speak. . The lever doesn't seem to...

my 1050 works great in warm weather, but chatters when i raise the attachment in cold weather. don't have manual. how do i check fluid level?

I'm having issues with my hydraulics. When I change my hydraulic/transmission fluid and filters, the hydraulics work great for about 2 hrs. Then the hydraulics diminish and become jumpy. I used the tractor supply hydraulic/transmission fluid and a Fram PH8A filter. When I check the fluid it...

Thinking about buying the John Deere 1050 from work. As far as i can remember the thing has always been somewhat messed up. The thing seeped oil out of the head like crazy, constantly overheated, and just little other things that aren't ideal. Always ran though. Never didn't start, etc...

Hi all, I have a 1988 JD 1050 and the hour meter / tach is not working. The cable is fine. A speedometer shop has opened it up and so far has reported that the meter is fine, but the spring for the tach is broken. He is going to work on it further to see if he can repair, but it's doubtful...

My dad is using his JD 1050 utility tractor with a post hole auger. He wants to know if there is a down pressure adjustment on this tractor. There appears to be down pressure when using a cultivator but we have no idea how to adjust it. Thanks.

on my tractor the bucket is stuck, in the curled down position and when i pull the lever to bring it back the bottom hoses (which are the ones in the middle of the ram) go super hard. how do i fix it.

Hi All, I have purchased a 1050 that has had a 430 loader welded on to it. I would like to put the original quick hitch mounts on. Cutting the welds off isnt a problem. Can someone please show me what mounts are used and is clearencs a problem with the clutch linkages. I will try and attach a pic

I am experiencing electrical problems with my JD 1050. A while back it blew the top off a new battery. I checked the voltage output at the battery and it was charging at 18 volts....too much. I took it to a repair shop for other issues and while it was there I had them check the alternator...

I want to change the hydralic fluid. Never done this before. I have new fluid and new filter. Is this done same as with oil change, just drain fluid and change fiter? Any other steps? (No loader on tractor, just three point hitch)

Hi, I have a 1986 JD 1050 and need to have engine rebuilt since the middle rod bearning was shot. Does anyone know of a good place to have this engine rebuilt? The engine model is 3T90TJ. I live in Western New York, but wouldn't mind traveling if I can find a good rebuilder. Thanks for the help!

Anybody ever timed a JD1050 fuel pump. I followed the instruction outlined in the owners manual, but that doesn't seem to work. Course, I could be doing something wrong.:confused2:

I'm looking at a used, but nice and straight, JD 1050. Current older gentleman is the second owner, said hour gauge was broke when he got it. Any thoughts or things to look out for? I will add an aftermarket loader, probably Westendorf. Tractor can be seen here: John Deere Model 1050 Four Wheel...

Looking at purchasing a 1050 with loader/backhoe advertised as "low hours" for $10k. It comes with a 5' brush cutter and 6' finish mower. Assuming hours is in the neighborhood of 1500-2000, is this worth a look? Also, any issues with reliability or replacement parts for this 20+ year old...

I am the proud new owner of a john deere 1050 ..... The gear decals (4x drive, gear, hi/lo) are all or mostly scratched off. They have them at the JD store - but they are all like $15 EACH. So just getting three would be $50 ! Not to be a cheap skate or anything, but is anyone aware...

I put some money down on a JD 1050 today at a local JD dealer.......... a 1050, 4x4, FEL, 2400 hours. A few minor leaks here & there.......but started right up this morning & it was 28 degrees or so. Seems to be in decent shape. $7200. Anyway, the PTO was turning even when the lever said...

I have a john deere 1050 2wd . It used to run fine all day and now it over heats after about 30 min of running it. I put new belt on and flushed the radiator real good. But still seems to over heat? Was thinking of maybe getting radiator cored. Any ideas would appreciate it. Also replaced new...

I have been looking at tractors, of course this is why I am posting here. Looked at many brands on Craigslist. Small amount of land, horses, mowing a few acers, moving hay ,box blade work, and manuer removal. General dont want to break my back need for a tractor. Nothing big, something in...

Had my deere (2wd 1050 w/75 loader and backhoe 8, no power steering) in for some electrical work last month, and while there had the hydraulics serviced - replace filter, clean screen, new fluid, etc. While unit was there, had bucket off (universal attach plate) so when they tested hydraulics...

I own a John Deere 1050 with lots of umph, but I need to know the type and brand of hydraulic fluid to top off the reservoir. Had a leaky hose that has been repaired.:confused3:

Hello All I have recently purchased a used John Deere 1050 and I'm having problems understanding why my 3 point hitch will not stay were I position it . It keeps drifting up or down when in mowing . I have played with some of the knobs under the set but I'm not sure if they are set right . The...

We have the John Deere back we bought new in1980 it now has a fel on it.the person that owned it kept the fluids changed .I havent changed the Hyd filter or cleaned the screen yet , but I'm noticing the hydraulics don't seem firm and responsive they respond up down and the bucket curls but it's...

I recently bought a JD 1050 and the tractor runs great; however, there is a grinding noise when engaging the PTO and an implement is attached, but it does not grind when there isn't anything attached. There isn't any grinding when disengaging the PTO in either scenario. Anyone know why it would...

Last night I hopped on my 1050 to do some mowing, and while hooking up the 3 pt mower, I noticed whenever the 3 pt arms were up, there was a noise when I would press on the clutch. Sounded like something small knocking around in there. If the 3 point was down, no noise. Weird. I also noticed...

I have an older Jd 1050 that I split earlier today Thinking the clutch broke. When I got it apart I found the Input shaft has broken. Anyone have the bell housing off one of these. It looks like the new shaft is installed through the end that's attached to the tyranny. Thanks. Rod G.

what is the best oil to use ?

hello there new to this sight im looking at buying a 1985 jd 1050 with a mower attachment its got 2800 hours and pooks pretty good there asking 7500 is that a good price and is there anything i should check on the tractor when i go see it? thanks for the help

Hello, brand new member. Need some help. Hailing from Elrod, Alabama. Some History: I have a JD 1050 (diesel) that has been operated very infrequently for the last 15 years. When I say infrequently, I mean 2-3 times a year bush hogging. I went through it pretty well when I bought it: changed...

I am trying to find a steering shaft for a 1983 John Deere 1050. The shaft has to be replaced as the bearing surface on the threads on the bottom end of the shaft are separating. The shards of metal jam the ball bearings and force the tubes apart, spilling the bearings into the steering box...

There is a 1050 for sale here in the Denver area. It has a loader. The owner says it needs a new head gasket. He wants $4500 for it with the bad head gasket. Is that reasonable? Will I be able to do the head gasket ( have done cars and boats, etc. no problem)? Will 33 hp be enough for an acre...

Bought a 1987 Deere 1050 a couple days ago and feel as though the hydraulics are a bit weak. When trying to move snowbanks, the loader didn't have enough power to lift them. Has enough down pressure to lift the front wheels, but it also has a backhoe on the rear. Is there an adjustment to the...

OK, so the JD 1050 has gone for 27 years, without an issue, other than oil changes, etc. Now, it has surprised me with a leak around the air bleed screws of the fuel finlter housing. Manual says, it may be necessary at some point to repair this, so not unexpected, given its age. Problem is...

I just got done replacing the cylinder head gasket on my 1050. I had the head resurfaced. I am now having problems getting the tractor to turn off. Before working on it, I would turn the key to the off position and turn the throttle all the way down and it would stop. Now I have to mess with...

hey, everybody this is greg it's my first time so please bare with me im not the best with a computer.

Does anyone know if the rocker arm assembly has to be removed in order to remove the cylinder head on a John Deere 1050? This is a three cylinder diesel. I am replacing the cylinder head gasket.

I'm working on a John Deere 1050 and trying to remove the exhaust manifold and turbo. I have a tech manual and have done everything it has said to do. I removed the three bolts and one nut and it won't budge. Any suggestions? My final goal is to remove the cylinder head and replace the head...

Greetings all- I am a long-time lover of Ford tractors (Ford, not NH), but purchased my first John Deere last summer. It is a 1986 1050 with only 350 hrs. It is in very good condition, and seems to do everything it is supposed to, but I am frustrated with the TPH hydraulics. Even at normal...

Hi, I have a jd 1050 4wd and a jd 75 loader I took off an old 850. Can anyone tell me what parts I need from the selective control valve to the levers and if there are any aftermarket parts that are compatible?

I'm looking at a JD 1050 2WD with 1,100 hrs (early 80s model). It has a Bush Hog front end loader. They is an oil leak around the valve cover gasket and a rear tire that will need to be replaced at some point. Everything else seems to check out OK. I plan to use it for light bush hogging and...

1980 JD 1050 2WD, AG tires. Looking for a box blade and I am not sure if it would handle a 6' box blade. I am looking at the Howse brand and also the Tractor Supply line. Will be mainly used to level dirt and gravel driveways from time to time.

Looking at a 1050 2WD now. Has lousy turf tires front and back. Has chains on rear, also. Really needs rubber all around. Any idea of cost for ags on back and ribs on front? Also, is this tractor worth a hoot, it appears to have more HP than the weight and 2WD can utilize. Asking price 5400...

Hi all, I recently purchased a used JD1050 and noticed that when I pull the PTO lever back to disengage, the shaft continues to turn ever so slowly. If I keep upward pressure on the lever, the pto will stop completely. If I let go of the lever, it slides forward a fraction of an inch.....just...

The slider gear that allows movement from low to high range appears to be ground up. I'm also guessing the gear it interfaces with is tired. How much of a job is it to take apart the tranny and replace these gears? Is it a 2000 dollar job? I'm sure the gears are not accessible through the top...

What's everybody's opinion on this tractor,only has 1100 hours?

Hi Everyone, I am looking for a good tractor for the following uses: -moving cut trees (about 8-12' long and from 1-2' in diameter) -moving lifting rocks on my property (I live in rural CT and we have a LOT of rock/ledge) -leveling out land (moving soil with rock) -digging out stumps I found...

I just installed a jd 75 loader,all connections are correct according to Woods equipment and Surplus center,now my 3 point hitch will not raise what am i doing wrong? Any ideas or suggestions? Please help.

A couple months ago, I went to a local dealer just to browse and talk to them about compact tractors. The sales guy showed me a 1987 JD 1050 that he thought would be "perfect". Diesel, FEL, box blade (think that wad a JD also), turf tires, power steering, 4wd. 1100 or so hours on the meter...

my jd 1050 will not stay in reverse. it might not be going all the way into reverse. i do not know

Looking for a used control valve for 89 jd loader, or what kind do i buy for it ?

I have a 1050 4wd I replaced the left front hub bearings on and after i got it back both front tires lock up when i drive in forward the front driveline is not hooked up on it so i know its not locked up in 4wd it goes backwards fine just not forwards. also when i pick up the front end and turn...

Hi- I am new to this forum, so please be patient as I find my way around. I am in desperate need of some NLA parts for a John Deere 1050. Does anyone have ANY suggestions at all? Any help is greatly appreciated!!

Does anyone know any where that I can search for NLA John Deere parts? Desperate!!

I am looking for the following parts for a John Deere 150: ch13128- camshaft ch13129- pin fastener ch13127-camshaft Does anyone know who might carry old/NLA parts?

need help finding an exploded view of the dual clutch for this tractor to help with repairs. any suggestions welcomed!

I have a JD 1050 with over 9400 hrs on it. I was told when I bought it a rebuild was done at about 7K hrs. It seems to run fine but something concerns me and I'm wondering if it is normal for this tractor. The question is when I start up cold the oil pressure is 50 psi. After warming up it...

for once, I think the title says it more or less all. my father in law experience jerky operation of hydraulics this fall and sent his tractor to the dealer. They found excessive quantities of water in the hydraulic oil. Works fine after hydraulic oil change but they were unable to say how...

Hi, This is my first post. I have a JD 1050 which I bought used and had the dealer go over it and do all fluids etc. The dealer thought is was a solid machine ( about 530 hrs at the time) After 6 months use, earlier today I lost the ability to shift the Hi/Low transmission. Had never had a...

I am looking for a rear rim for a John Deere 1050. Mine is corroded due to ballast.

Local dealer has a JD 1050 4wd with loader for sale,not sure of hours,tach wasn't working. Seemed like it was in good shape,did have some loose steering from driving it round the lot. It did have a hydraulic top link and arms,thought that was interesting. One thing was the loader was slow to...

Anyone have any experence using a 1050 with a 75 loader? My Dad just bought one.

I was wondering if there are still a lot of these 1050 4WD out there and how are they holding up?

I am looking for help with a JD1050 2wd that I recently bought. I am trying to do some repairs to it and and need some ssistance with the front wheels as one of them has rusted through and the other is probably not far behind. I will attempt to get the holes welded up but in the event it is not...

I am looking for help with a 1986 JD1050 2wd that I recently bought. I am trying to do some repairs to it and and need some ssistance with the front wheels as one of them has rusted through and the other is probably not far behind. I will attempt to get the holes welded up but in the event it is...

Hello, new member here. I am looking for help with a JD1050 2wd that I recently bought. I am trying to do some repairs to it and and need some ssistance with the front wheels as one of them has rusted through and the other is probably not far behind. I will attempt to get the holes welded up but...

I have always had a starter issue with my 1050 since I bought it 4 years ago and I have been jumping the starter to get around it but want to fix it once and for all. Turning the key would sometimes start it and sometimes not ( it would just click ) . Battery was replaced - no difference...

Hello, I'm new to the forum and I joined in hopes of getting some help with my 1986 JD 1050 4x4 light utility tractor. I've been having problems getting the PTO to engage and in order to do so I have to idle the tractor down very low or the best method is to shut it off and put the pto in gear...

Hi, I'm looking for a JD 1050 drawbar. I've tried the local dealer and a bunch of salvage yards but nobody has one (and it's not available from JD). The JD parts manual lists the part number as CH14119. Any help is appreciated. Thanks.

After my last project, I noticed a serious drip, dribble coming from under the tractor. Hydraulic/trans fluid. It seems to be at the seam connection between the trans and the rear I guess. In front of the shifter, but behind the 4wd actuator. It looks like one of the places where the tractor...

HI I have a john deere 1050 that i put a new clutch in early this year last week i was mowing my field and everything was working great and then the pto started acting like it was slipping. It will start slow and the get up to speed when you start mowing again it will just slowly stop not bog...

Does a John Deere 1050 have an adjustable pressure relief valve that would possibly provide a little more loader lift?

I own a JD 1050 that does NOT have a FEL. I think this is a great tractor for the uses I have for it. I may have an opportunity to purchase a JD(8B I think) backhoe attachment for my tractor, but a friend has cautioned me that mounting a backhoe on a tractor without a FEL, to stabalize the...

I have JD 1050 in good running condition. 4WD and a FEL. The unit has 3800 hours but mostly cleaning out the barn and garden work, nothing very heavy. I think somewhere in the $7K - $8K range. Any recomendations? The machine is always been sheltered. :o

Does anyone know what turbo brand/model is on the JD 1050. Thanks, Mike

I have purchased a John Deere 1050 and it is my first tractor so forgive me if this question seems dumb. Is there a way to disengage the PTO other than depressing the clutch? For example, when driving the PTO shaft is always turning. I thought that there would be a way to stop this, but I can't...

Greetings. I have a circa '85 JD 1050 w/ loader and backhoe which I use intermittently. Last time I used it was this summer. Went to use it a few weeks ago and I cannot get the clutch to work. Depressing clutch pedal to put tractor in gear results in grinding. Couple of guys locally said this...

Hello, I'm new to this site and was very happy to find it. I have a John Deere 1050 that was made by Yanmar. 4WD, 33 HP,3cyl diesel. Does anyone know the comparable Yanmar model number. As far as tractors are concerned I don't think this is very old, I have a '48 Farmall that I can still buy...

Does anyone know of a direct replacement for the J.D. 1050 engine. It came with the yanmar 3T90T-j engine. I would like to find something that has a parts supply that would bolt right in.

My 1050 seems to have a chirp or maybe a squeel coming from from the turbo area at mid to high rpms. It seems to be getting worse. Where do I start?

1982 JD 1050,looks like it is 2wd and not sure about if it has power steering. We would be using this tractor on our land in WNC to clear it of brush and keeping driveway scraped. Price is $3000 and it might come with a bush hog,not sure yet. No idea on hours or anything else. So what...

I didn't replace the clutch last time, so I don't completely understand what goes wrong on them. I noticed after a winter of using the new clutch, it needed a little free play adjustment. Now after a month or so of mowing, it has a bunch of free play and I have trouble getting the pto engaged...

Has anyone out there replaced the rear main seal on you JD1050? I have to split the tractor for a trans clutch replacement and I have just a drop of engine oil show up on my shop floor after each mowing and I want to replace the rear main while I have it apart. It will just entail the extra...

I have not torn into the clutch on my 1050, so I admittedly do not know as much as I need to about them. The clutch went out last September, and I knew I needed it to finish mowing an move snow, and I had no time to do it myself, nor the stands to split the tractor, so I had it replaced. All...

I have a Service manual on my JD 1050 that I just acquired and in it it shows that the 850 and 950 has an internal Overriding clutch pack but nowhere does it show that the 1050 has one???? Can some of you tell me if mine has one internal to the tranny or do I need to be installing one on my...

Well folks, I just bought a pretty slick 1050 John Deere with only 1600hrs that has the PTO clutch stuck. I have checked and double checked the pedal adjustment according to the JD manual and I have 9/16 free clearance which is the minimum per the manual. What is the best way to break the PTO...

I have an '84 1050, 4x4. It won't crank. I have both levers in neutral, shifter and hi-lo range, and hit the key and the starter goes clunk. I have enough juice, the battery reads 12.84 volts. I've even run 2 batterys thinking this one may be bad, but nothing. I can hear the solenoid throw the...

I could use some help here too with snow removal. I am getting frustrated at this point. I have a JD 1050, 4WD. I have about 1/4 mile of lane gravel, and the lane is poorly designed. We will fix the lane in upcoming summer months since it is the lowest point anywhere, and the snow piles there...

Symptoms and History. Tractor has two sets of SCV's on the right side with two operating levers. Recently the one that operates the bucket would travel well past it's stop point. As if the E-clip came off in the lever assembly and not allowing it to automatically return to "hydraulic-neutral"...

I have a JD 1050 Diesel with front wheel assist. I need to get a front loader and am looking at adding either a Westendorf, Allied, or Koyker to my tractor. Any suggestions, pricing, etc., etc. would be more than welcome. A good used one would be fine too. For the Koyker I was looking at a 160...

I have a JD 1050 Diesel with front wheel assist. I need to get a front loader and am looking at adding either a Westendorf, Allied, or Koyker to my tractor. Any suggestions, pricing, etc., etc. would be more than welcome. A good used one would be fine too. For the Koyker I was looking at a...

Has anyone did anything to improve the hydraulics for the loader on a 950/1050? My loader (#80) just moves so slow. I know the pump is only putting out 6 or 7 i think GPM. I have changed the hydraulic filter.

Would you believe I can't find any front ag type rims for a 4x4 john deere 1050? The jd part no is ch13187, jd has in their infinite wisdom discontinued them. The tractor is really a Yanmar, and if I knew what model Yanmar is the same as the 950/1050, the rims should fit. They are 5"x16" rims...

My 1050 wants to pop out of reverse unless I keep my hand on the shifter. I took the cover off and found that that reverse shift rail does not want to slide all the way into position like the other rails. The fork appears not to be bent, the detent ball bearings are new as well as the springs...

I am trying to figure out how to raise the 3pt hitch all the way up. It raises so far with the normal 3pt control lever to the right then I have to raise it the rest of the way with the small lever behind the seat. Once I get it fully raised with the small lever, it goes about half way down and...

I need to replace the clutch in my 1050. The PTO clutch seems fine, though I will be replacing that clutch disk also while I am in there. I never fooled with a dual stage clutch before. My plan is to replace the tranny clutch disk, pto clutch disk, pressure plate, bearings. Are there two...

I have the opportunity to buy a John Deere 1050 4wd compact utility with No. 80 loader for less than a $1,000. The tractor needs a clutch for sure. The motor starts and runs good. The loader operates fine also. Besides the clutch needing to be replaced, the sheet metal front nose is pushed...

I just recently bought a Yanmar 336D with front loader, backhoe and scraper but no ROPS. Would like to put one on before I move it to my property up in Washington in about 5 or 6 months. Also, looking for a used one, if anyone knows of one. I know they have new ones but I am not ready to...

I'm looking at a 1984 1050 2wd with a bush hog and a harrow for $4,700. It has turf tires and it has 3600 hours on it. I have attached a picture of the tractor. I have just started researching the 1050 model and really have not been very successful with finding many reviews so I have a few...

Can someone explain the functions of the rear remote on a 1050 to me? There are two levers. The outer lever moves easily and I use it for my hyd top link. The inner lever is where I have a question. It seems to remain in position when I push it forward or reward. It's very stiff when moving. It...

Just a shot in the dark, hoping for some help. My temp warning lamp used to come on (as well as the oil and charge lamp) when switching the ignition to "on". Now it doesn't. When I ground the wire off the sending unit the lamp will light. The shop manual says the the temp lamp relay is bad. I...

Just about done with a makeover on my 1050 MFWD. I made 1 good hood from 3 and found a set of fenders that were perfect. They were all blasted an painted and I bought a new front grill and headlight trim,which I thought were reasonable from the dealer. Replaced the dash,also reasonable, and...

I just purchased a 1985 JD 1050 MFWD and need some advice. I need new fenders and a hood and have tried all the conventional salvage yards on the computer. Any other places to go would be of great help. Also, I suspect the MFWD is not working. Would the first place to go be to take off the shift...

i have about 2000 hrs on my jd 1050 4wd. the engine has been rebuilt. i bought the tractor with about 900 hrs on it in the early 90s when it was about 3 years old. i used it to pull 6 foot attachments including a 6 foot bushhog in the woods and a 2018 disk harrow. i have been told i wore it out-...

I have a 950, next smaller to the 1050. The 1050 has a turbo diesel engine. They were made from 1980 to 1988. I did not think the 1050 came with hydro option. I am pretty sure they were all gear drive. All the x50 series JDs are good solid tractors. But it may also be a little large for only 2...

Hi folks.. This is my first post.. please be gentle! ;) Short story, I have been shopping for a CUT for quite a while. Pickings are THIN. I am currently trying to decide between a JD 1050 and a JD 4300. My useage: Mow the lawn (2 acre), retrieve and process firewood, maybe 5cd a year...

I am looking for an operators manual for my 1983 deere 1050. Any suggestions? Thanks

jdown-ML-807560-ML- John Deere specific post

I just bought a John Deere 1050 at a good price. After working it over the weekend, it appears the head gasket is "seeping" on the left side. It's damp at the rear and more on the front and rear corners. It looks like replacing it will be a fairly straight foward repair. Anyone have any...

Has anyone had any experience with taping into the hydraulic system of a JD 1050 to add remotes?

Has anyone had any experience with taping into the hydraulic system of a JD 1050 to add remotes?

Hello. I am trying to get a price estimate on a JD1050 with FEL. It is from a friend that has no idea how much to ask. It has roughly 2300-hours, in fair condition. It is also a 4x4. I have found a few prices, but they range dramatically. Any help would be helpful. BTW - we live in...

My neighbor has a John Deere 1050 not sure of the year. He wanted to me to find out what grade oil and how many quarts he should use for the engine oil. The tractor is like new and only has 310 hours. He used to bring it to the Deere dealer but they closed. Thanks

I'm looking to purchase a 1050 MFWD with 1500 hrs, R1 tires, 75 loader , 8 backhoe, runs well, no signs of abuse, one owner. Any pricing opinions?

Hi guys, I'm looking to buy my 1st tractor, and have an opportunity to purchase a private sale, 1050 with less than 600 Hrs. It's late 80's, 33HP turbo, rear PTO only, 4WD, PST, 80 FEL, 2 spd gear trans (8-2) ,Ag Whls (lots of cracking in the walls), no signs of leakage, 2 owners.... he wants...

I am looking for all four ag wheels for my JD 1050. I was wondering if anyone might know of a tractor salvage yard in their area that has a JD 1050 4WD.

A auction this weekend has a JD 1050 4wd w/ front loader. 2100 Hrs,13.6 x 28 tires @ 50%, new paint, 3 cyl diesel engine. I think it may be an 80's model. Any idea on what a fair price would be?

I just bought a JD 1050...(1980-1983) .....I've got the repair manual, but I can't seem to find any sources for the actual owners manual that would have come with the tractor...anybody got one or know where I can get one? Thanks in advance!!!!

I am looking for user ag tires and rims for my JD1050 4WD. I know I need 13.6x28 rear tires and 700x16 front tires but I dont know what size the rims are. Can anyone tell me what size the rims are?

Folks, I have a Model 80 FEL. I noticed that on the larger model Kubotas, 4600 series for instance, that Kubota uses a strut brace that goes across the top of the FEL boom. I'm wondering if something like this is available for my FEL. She's had some pretty good use and a brace like this would...

Folks, I'm new to tractors. I recently bought a 1988 JD1050 with 800 hours on the clock. She runs really well and I am quite happy. I have a question regarding the 3 cylinder turbo yanmar diesel motor. When I start it cold it clatters quite loudly. The noise dissapears when she's warm. I think...

I have a JD 1050 4WD with turf tires. I would like to put Ag tires on it. I will need to change wheels also. Would anyone know where to find tires and wheels on the used market? Would anyone like to trade?

I have a JD 1050 4WD with turf tires. I would like to put Ag tires on it. I will need to change wheels also. Would anyone know where to find tires and wheels on the used market?

Wont move at all. I dont have a loader on so i dont know if the pump is working or not. where to start?

Does anyon here have a JD1050 4x4 with ag or R4 tires. If so what size are they (frount and rear). I would like to swap my turf tires for something with a little more bite but I'm not sure what size I should be looking for. I would be looking on the used market for both tires and wheels. Also...

ANyone had any experience with the 1050 model? If so what is your take on this tractor,thanks again-Lloyd

Well, we finally moved to the country, and now I'm looking at tractors. There is a 1989 John Deere "springer"? 1050 tractor for sale with 554 hours on it. It appears to be in good shape. His asking price is $7000. No implements, no loader, just the tractor. Sooo... is this a good price? (Private...

Does anyone know the Horsepower of the JD 1050? Was it a model that was reliable? Were they produced in large numbers?

Photo of 1986 JD 1050. Tractor was purchased new by a golf course, I'm the second owner. Has about 5900 hours, and an excellent tractor. Paul

Can any one tell me how to tell if the turbo on my John Deere 1050 loader tractor is working? It is about 12 years old and 630hrs. I bought used about 3 years ago. It seems to run fine but I can't tell if the turbo is actually working. I have opened the turbo intake and can see the turbine...

Have a bad back and need a more comfortable seat for a 1977 jd 1050 tractor. Anyone know a source to find a better seat for a 1050?