I need some help finding a front rim for a 2000 Deere 4100. Deere doesn't carry the part anymore and I've exhausted all my contacts without success. The Deere PN is AM879344 and holds a 5-12 R1...
Hello readers,
I am at a dead end. With warm weather finally at the house. I decided to swap engines from the 4100 gear driven ( rear end went out )
and the 4100 HST ( Middle piston went after a...
I want to know if I can remove the right front axle 4x4 spindle on my 2002 JD 4100 without taking the 4x4 hub apart. would like to remove its housing intact from the axle.
John Deere 4100 hydrostatic drive. FWD not working. When I acquired the tractor there was a clicking noise in the front hub - right side - as I was unloading it but it stopped clicking within a...
Hi all, I’m trying to replace the oil tube on a 1998 JD 4100, part number LVA800157. I got the tube disconnected, but I can’t get the tube out because it runs over top of a large cross-bolt under...
I have a John Deere 4100(gear) with a 410 loader. I want to replace the seals on the hydraulic cylinders. My problem is that the serial number of the FEL is WO0410X014991 but the parts listing...
Looking at the used tractor noted in the subject line. Here is the package (all one owner):
-Tractor with 304 hrs (looks like it has sat outside a bit during its life as it has surface...
My 1998 JD 4100 HST won't go into reverse or go forward. The shift lever between low and high now just slides back and forth and won't click into either position. I was moving some dirt around and...
I noticed the other day that my power steering felt a little notchy and not smooth and the brakes were making some noise.....and then today I noticed that the 3-point hydraulics up and down felt...
I have a JD 4100 Compact Utility tractor and when backing a 4 wheel wagon in I had the 4wd engaged and turned very hard to the right while in reverse. I noticed a popping noise, in right front...
Greetings! New member, just picked up a pretty nice JD4100. I am having a hard time finding a part number for the "4100" hood decals; anyone have the numbers handy? Thanks!
Yanmar 3TNE74 engine.
I put in a used engine 200h ago. Used Walmart supertech 15w40. Changed it tonight with Delo XLE with isosyn.
Thought I wanted a "better" oil, but now I'm thinking on an...
Anybody have a source to buy a replacement cylinder for my 410 loader. My tractor is in the shop for past 3 months and still need a new/rebuilt loader cylinder. ANYBODY?
Hello, this is my first tractor JD 4100. I got it the other day, it ran fine for quite a few hours, multiple times I turned it on and off with no problems. When I tried this morning it would not...
Hello, this is my first tractor JD 4100. I got it the other day, it ran fine for quite a few hours, multiple times I turned it on and off with no problems. When I tried this morning it would not...
New member and owner of a jd 4100 with 410 FEL. I recently purchased a box blade and after using it a hydraulic top link would make operating it so much more user friendly. So my question is this...
Ok here goes I have a John Deere 4100.
Starts fine runs well does it's job. All is well until I stop with the tractor running put it in neutral
get off the tractor with it running get back on...
I'm hoping I don't need to go look for my 4100 manuals, and I won't if anyone can provide the required torque for the wheel bolts.
I figure someone has all that stuff at the tip of their fingers...
Anybody have any experience with troubleshooting the Control Module in a JD 4100?
This problem started off with the tractor turning over but not starting. Traced issue to fuel solenoid not pulling...
Battery not charging, 12.7 volts at battery while running I think it should be 13.5 to 14.5 . There are only 2 small wires on the alternator I pulled the plug apart and checked voltage while...
Hi All,
Long time lurker for my 318, but recently picked up a 4100 and looking for some advice. Wanted to change all filters/fluids. Went to the dealer and picked up Low Viscosity Hy-Gard for the...
John Deere 4100 fuel solenoid intermittent pull in.I replaced the solenoid and switched the fuel and start relay with no change, sometimes it starts sometime it cranks but no start. I can hear if...
JD4100 would turn over but not start due to fuel solenoid not pulling in. Discovered A2 control module was defective. Bypassed A2 function by adding a 12vdc delay on timer. The timer is wired to...
I bought a model 4100 deere that is pretty hard to start. I am not sure how to preheat the glow plugs on this tractor. I tried pushing in on the key, but it will not budge. Cranks for about 15 or...
I bought a model 4100 deere that is pretty hard to start. I am not sure how to preheat the glow plugs on this tractor. I tried pushing in on the key but it will not budge. Cranks for about 15 or...
I have posted about this related problems and received great answers.
Problem:
Status: New Solenoid (works) tested by grounding to (wht Solenoid wire in connector) in/out great, wire seems to get...
I do believe I must replace the injector pump and Injectors due to my worker put gas in my diesel engine. I did replace the fuel pump and still won't start. It was running fine and just quit. I...
Anyone have an idea where I can get some reasonably priced used rear fenders for the 4100? The new ones are above $600 each and I can't afford it. I just recently got tractor and I'm trying to...
As the title suggests, is there a hydraulic release lever or nut that can be turned so the wheels can free-wheel and prevent damage to the hydraulics like you might find on a Z-Trac or smaller...
I bought a used 4100 but the lift arms will not go down on the rockshaftand I can't figure out why. I've played around with the flow control on the rockshaft, I've added weight on the lift arms...
I have a JD 4100 and wanted advice on which diverter to buy so that I can install a grapple. Artillian has a kit but I can't see spending $700 on it when I think I can do it for less than half...
I just got a 4100 and I'm interested in installing power beyond for grapple, etc. I've been doing research and I wanted to know if the tractor comes with the M808033 plate that you hook up the...
I have a JD 4100 and it quit running. Been acting like this for about a week. I did some research and more confused than before.
I dont know if my 4100 has a thermister on it?
I can see there was...
I am in the process of bringing this tractor back to life after sitting for 4 years. Changed all filters and fluids and it runs and drives great. My problem is the front loader and 3 point will...
My neutral swt seams to be acting up is my guess. Having to work forward ->neutral<-- back and forth trying to find the spot to turn the engine. I make sure my PTO is in neutral, step on the...
I'm looking to build a lawn leaf blower and for my John Deere 4100 and other tractors.
I purchased the fan blower system from DR trademark to install on my 3ph and decided that I would rather run...
The book says
The following John Deere coolants are preferred:
キ COOL-GARDョ PRE-DILUTED SUMMER COOLANT (TY16036).
キ COOL-GARDョ CONCENTRATED SUMMER COOLANT (TY16034).
If neither of the recommended...
I'm looking to buy a John Deere 790 and sell my John Deere 4100 and want to know if my 60 inch mower deck will switch over to the John Deere 790.
Are there any difference in mounting from the...
I have a '00 Deere 4100 with the 60 inch mid mower deck and the gear box has failed. OEM replacement part AM143311 is ~$800.00. I'd like to rebuild the box if possible since I think JD's costs...
Looking for some advice on my 1999 John Deere 4100 HST. When key is in the on position everything is fine, lights work etc. when I turn they key further to start the engine, it may turn over a few...
Hi all, looking for some advice to troubleshoot. I have a 2000 4100 series compact 20HP tractor. I turn the key and the starter won't engage. The dash lights come on for a few seconds, sometimes...
Hi all. This is my first post here, but have found a ton of great information throughout TBN.
I'm having a problem with my 1998 4100 gear transmission. I was brush hogging, put tractor into...
I'm looking for a small 4wd machine to keep my driveway clear and mow a couple acres of lawn. I would like to spend $5000, but I can go up to $8k. I had another thread going on here, but I've...
I appreciate any information and help anyone wishes to share.
I am a 72 year old disabled vet who has just been diagnosed with incurable lung disease. Dr. says to stay indoors, and rest. Ya, like...
I am having an issue when trying to start my JD 4100. The few times that it does start everything turns on correctly and when you throttle up or sometimes just pick up the loader it will cut off...
I have a JD 4100 that I picked up a few years ago from my father at a great price when he ended up moving and not needing it any more. I've had it for around 3 years now, it's a 20-ish HP diesel...
This is for a buddy who inherited a JD 4100HST at his new job. Who ever worked it before, for some reason pulled the safety wires off the prongs under the seat left side ( the Safety Switch and...
Need help with electrical problem. I had a short in a add-on cable to operate a sprayer unit. The Voltage rectifier/regulator module burned out. Replaced this module and now The Charge/Discharge...
I have a 2000 JD 4100 with 765 hours on it. I'm having an issue of a blown 10 amp fuse when the mid point PTO is engaged. Typically the fuse has blown after PTO is engaged for several minutes...
Some of you might remember I was forced by John Deere last Sept to pay out over $2000 to get part number AM880071. Well the new part was installed in November ( after surgery )
and I was calling...
details: 4100 was overheating.. which was odd since I had it flushed back in DEC. I look inside with a endoscope and see the tops of the corp tubes were clogged up. Thus took it out
and that was...
I had the pilot bearing on the flywheel go out and chowder the splines in the clutch and on the shaft effectively leaving me stranded in the woods. Took it apart and replaced the pilot bearing...
A piece of the 3ph upper mount point broke off on my tractor.
I am considering the following options. I would like the least expensive way but it has to be safe to use.
1. weld it my self with my...
I am trying to fix my neighbors John Deere 4100. It sat for a couple months this summer and when he went to use it in the fall the three point hitch wouldn't raise or lower. When you move the...
I thought that I saw a discussion on this before, but can't find it now, but I'm not sure where to start with finding the problem with cold weather starting on my 4100. It starts like a dream...
Seeking replacement rims for the front of my 4100 so I can mount 23X8.50-12 Deestone 6P Super Lug Tires AG DS5241. The current rims are the narrow factor tires for AG
Hi, I'm looking at purchasing either a used 4100 or a new 2025 and have a question on the loader. I know how easy the new ones are to remove, but not sure about the 410c style on the...
Tractor 4100 4x4 hydro has been flawless for almost 2K hours. However... looks like there's an issue with the front axle
gears or at least that's where I notice the issue. Tractor front axle jerks...
I ordered a John Deere filter kit (LVA21197) for my 渡ew to me 4100 tractor. I changed the engine oil and filter, the air filter, and the fuel filter?but there is one filter left from the kit...
Really bad day for my 4100 HST.. Rear PTO Popped while chipper shredder was reducing RPMS. Sad part is... The original PTO shaft went about 10 years ago..$100 fix..now it's upwards of $800...
I just inherited a JD 4100 tractor. I want to give it a good starting point by changing all of the fluids and filters. I've already ordered the JD filter pack kit with the air, oil, fuel, and...
My father has had this John Deere 4100 for several years now. He bought it mainly for all the mowing he does (about 5 acres). My parents have decided to move to a smaller place that requires less...
I went to use my JD4100 MFWD the other day and noticed a puddle of gear oil under one of the front wheels. Pretty obviously the seal at the lower steering joint had let loose and drained the oil...
I was given a block heater for the Ole 4100 ( reside in NW NC and it's hit in the teens the last few years )
as a Birthday gift. One issue. I refuse to pay John Deere $100 + for a simple adapter...
My tractor stopped running due to the fuel shut off solenoid is not being powered.
I've been studying the 4100 tech manual and it states
Voltage . . . . . . . . . . . . . . . . . . . . . . . ...
The engine of my JD4100 HST stalls after engaging the PTO switch in all 3 positions of the PTO selector handle, even without load.
Since the PTO-solonoid works OK I suppose the hydraulic PTO brake...
I have just purchased a 4100 from a estate sale and know nothing about it. The engine starts quickly and runs smoothly while the hydraulic lift works well but doesn't hold in the up position long...
March of 2014 My alternator started getting flakey on the 4100. So after much research and advice from members on here with
a similar issue. I ordered a replacement from total-power-parts on...
I have a 2000 deere 4100 with the yamar diesel in it.
The bucket only lifts about 8 inches, very slowly, reading the forums i did a complete fluid change to the trans. cleaned out screen by pto...
My John Deere 4100 has an electric problem.
The engine will only start when the PTO selection handle is in REAR PTO. Normally it starts in all 3 positions.
Besides that none of the 2 PTO's turns...
I recently experieienced a significant amount of smoke coming out of the engine compartment while brush hogging. I went straight to the barn, opened the hood, and found a small fire down under the...
Hi
I have a JD 4100 compact that will not start. Cranks over and produces smoke but no fire. It is not the fuel shut off, produces white gray smoke as it turns over, have removed air cleaner to...
Folks:
This baffles me, so at the suggestion of Kennyd, I post this before the cognoscenti. Please help.
Low hour Deere 4100, well maintained with factory 54" deck and model 410 FEL.
Joystick...
I have a 1998 JD 4100 Gear tractor and the hydraulics aren't working all the time. The first time the 3 point wouldn't come up I took it back to the dealer. They replaced the rock shaft and...
Hello everyone
Have a problem with a 4100 JD three point lift links
After 3 times to a dealer and talking to 4 others the 3 point still fails to lift.
Have a Land pride 5 ft finish mower 440...
I am looking to buy a tractor and ran across a JD 4100 that the owner says he put on a new loader. Looking at the picture it reads cx300. Is this loader compatible with the 4100? I can't find any...
Hiya! I have a great condition 60" belly mower that I need help pricing. I no longer need it and am going to list it locally to offset the cost of a brush hog. What are they worth? Thanks!!
Ok here痴 a new one for me. Working on a John Deere 4100, gear drive, Yanmar 3TNE74 JK1 motor. On start up, the motor goes to full RPMs. No throttle control at all, with excessive black smoke...
The other day I went to put my mower deck back on my John Deere 4100 hydrostatic tractor. My tractor was at one end of the building, I started it with no problem and drove thirty feet and shut it...
Hello to everyone ! My first post to ask for help in correcting a charge problem on my 4100. It has the stupid magnetic generator not a alternator like most are familiar with ? Can anyone explain...
Guys I have a 4100 that the loader is not lowering.
Background:Over summer I blew the metal/hose line on the rod side of one of the lift lower cylinders so I took the loader off and left it sit...
Hello forum...! I know there has been plenty of discussion around John Deere 4100 tractors not starting. I'm in the same boat but can't get a specific answer from the other topics. My 4100 had...
Hi, forgive me for being less then intelligent with a diesel engine. I was snowblowing today and my 4100 just quit. It will crank etc but no start. I think It might be fuel related but unsure how...
If there is already a thread...forgive me for starting a new one..doing this on the cell and while in class.
I have a 4100 HYD. Need new tires. But the ones I find that match the numbers look...
Just, looking for info or opinions. I work for a deere dealer but on the construction/mining side. But we also have some ag and turf dealerships also but I know nothing about it to say the...
looking for a little help diagnosing a problem on my buddy's 02 4100 gear. I always thought the thing lacked travel on the 3 point arms compared to other tractors I have used. it was maybe getting...
I had the drive shaft to my FWD fall out of the tractor recently. A few months ago I had to do a repair to it and when I reinstalled the drive shaft, I couldn't get the snap ring to close around...
I recently purchased a used John Deere 4100 HST and I'm looking to buy a Curtis cab and 47" two stage quick attach snow blower. My problem is I don't know the model number of the snow blower and...
I want to pass on some information and also solicit some comments on the glow plug controller (NGK 119650-77902) in my 4100. I was doing a lot of odd jobs around the place and had the tractor...
Hello all,
I'm not sure if I'm guilty of doing something that I shouldn't done? I was using my JD 4100 that I've owned since new this past weekend. I was moving gravel from pile to other side...
Hi all, I'm new to the forum, I am in desperate need of a schematic for the fuel shut off control module on a JD 4100.... I have searched here and google, the dealer is worthless, as I knew more...
I have a JD4100 that while blowing snow will just quit. If I let it sit, sometimes it will start. I'm thinking maybe it is in the key switch. Any Ideas out there.
New guy here. Registered some time ago but have been sitting in the weeds until now searching the forums and posts for information on JD 4100 front wheel spacers. Perhaps I am doing something...
I have a JD 4100. It had some electrical problems last year amd I ended up replacing the voltage regulator with a 40amp alternator. A few weeks after, it started having trouble starting.
When...
i am wanting to put a front end loader on my john deere 4100 and want to kmow what model to get and were a good deal on one is thanks for any help!! thomas
The lift arm was a little bent when I bought this tractor. I have tried to adjust but because of the bend or just rust it will not break loose. I would like to find a used arm if possible...
There's a two wire socket at the rear of the frame that's not connected to anything.
It's got no power with the light switch in the OFF position
No power with the flashers ON
12V with the...
The ball and socket joint end of the power steering cylinder near the front tire needs replacement. Unfortuneately, unlike the part
diagram MP17990 on the JD parts website that breaks this...
I have a very nice garage kept 4100 4x4 Gear sub compact with a 261 rear grooming mower with only 358 hours on it. Have mowed with it and moved a little snow but very little. Looking to get into...
Hello,
My dads JD 4100 will not start. It turns over just fine with plenty of speed but it never fires. I am getting fuel up to the injector unit but I am not getting any fuel out of the any of...
Looking for a nicely used 47" front JD snow blower and attaching hardware for a 2001 JD 4100 compact diesel. Must be in Michigan or Northern Ohio. Thanks all.
Was bush-hogging today and started noticing some jerky motion from the hydraulics - bucket, steering, 3-pt, along with a whining noise when they hydraulic system was activated. No problems noted...
I recently purchased a used Deere 4100 with about 400 hours. Overall the unit looks and operates almost like new. I'm having an issue with the 410 loader though. I've already removed it a few...
Hi, I recently purchased a used 1998 JD 4100 and the tires are pretty worn out, can anybody tell me where would be the best place to purchase new tires, looking for turf type tires, and, the sizes...
Hello. I am new to the forum and would appreciate any advice.
I just bought a nice 4100 and would like to add a loader to make it more useful. It is a 98 model and I am struggling with some...
I
I have a 2000 JD4100 CUT and it has had many issues as of late. It started a while back with a voltage regulator problem. My local people couldn't fix it so they just bypassed the issue by...
Yesterday I was out moving some firewood and brush with my 4100HST compact. The tractor had recently (2 months ago?) been completely gone through, a lot of new parts, electrical system check...
I have regretfully waited to buy a loader for my JD4100 that I bought over 10 years ago. The dealer says now I have to purchase mounts as spare parts and use a 200CX, all for around $4200. I was...
I was mowing the other day with my JD4100 compact utility tractor and it started making a grinding noise. Brought it into the garage and noticed oil leaking out of the front axle where the drive...
Hi,
I have been searching the forums for a while trying to figure out what size box blade to get for my JD 4100 (20 hp). I am leaning toward a 60" to get a little more done at once. The width of...
I have a pb kit on my JD 4100. The hoses that came with the kit have an odd cone inside the female fitting on the hose. It's a parker fitting, but has no part #. I've been searching for a little...
After picking up a 5' Bush Hog Box Blade for a JD 4100, I am experiementing with what we can do. It makes for a great counter balance for the FEL. But more than that, I would like to get better...
I have a 1999 JD 4100 with HST. By doing the stupid thing and trying to engage the diff lock while the rear wheels have been spinning, I have stripped gears or broken something in the...
Hello! I've had a little problem with having a dead battery. I hooked up a flamming river disconnect switch to see if that would fix it and it seems like it could be the alternator. After...
Just finished 99% of the fab work for the attachment. Got lots of pictures but I'd thought I'd start with a teaser. HAha:laughing:
I needed a fork attachment for my FEL, but didn't like the...
I have a loose axel on the right front of a JD4100. Oil leaks through the worn area.
I have the tire off and the eight bolts are removed from the M807518 COVER. Any ideas on how to get the cover...
Hi,
I have been looking for a first tractor for a couple of months now and I just wanted your input as to whether the deal I found is a good one or not.
I found a 1998 JD 4100 with loader...
New here. Recently acquired a 4100 with FEL. Noticing some play or slop in the right front wheel assembly when front wheels are lifted off the ground. Also notice the front wheel (left only) will...
Hi all, Towmater here! I'm considering getting a 3point hitch finishing mower. Will a John Deere 4100 with the Yanamar diesel engine be able to handle a 72" width deck or is that just to much for...
In particular I want to make sure my temperature light in the dash works and will come on if my engine were to overheat. It does not come on briefly, like some lights do when you turn on the key...
Hello everyone!
Recently got a Deere 4100 4x4 hydro and discovered a very bad oil leak just above the front, right final gear drive. When I put oil in the fill hole on top of the front axel it...
Hi All, I want to get a front John Deere snowblower for my recent purchase of a John Deere 4100. Can anyone tell me the model number of snow blower I need? Tractor is a 4100, 3cyl diesel, 1999...
First Post! Is there an adjustment to stop my tractor quickly after I remove my foot from the forward peddle? When I am mowing and using high range the tractor will roll farther than I like, I...
I see there are many backhoes available like the Wallenstein and some Woods, 3 pt style and I wonder if a small tractor like the 4100 can accomodate one? In my case, this is for strictly...
Hey Guys! Brand new here, but really appreciate you guys as a reference while shopping this out. I found a John Deere 4100 in better than average shape for a less than average price. Very eager to...
Hey Guys! Brand new here, but really appreciate you guys as a reference while shopping this out. I found a John Deere 4100 in better than average shape for a less than average price. Very eager...
Hi, I have a John Deere 4100 With a Curtis Cab. My cab has the split glass windshield. the lower part of the windshield was frozen and when I went to try to free it, it appears that the upper...
So I sold a BX2230 that I had for about a year - loved the machine but didn't want to mow with it anymore and had a hard time selling the deck so I sold it all (loader, mower, bagger, snowblower)...
I have a JD 4100. Has operated fine for many years. Yesterday I was driving it and I noticed the discharge light (battery) was on. Then I smelled a really strong burning smell and I saw...
Have a 4100 jd compact that keeps draining battery during use.Need to know how to locate and check safety relay as was told could not be allowing alternator charge to return to battery.Any other...
My neighbor needed money and decided to sell his tractor. He sold a well maintained and like new looking John Deere 4100 with industrial tires, loader, mmm, box blade, rototiller, weed sprayer and...
I cannot get my JD 4100 to start. When I turn the key it just cranks. If I play with the PTO switch on the dash a bit, I can start it occasionally. I could hear the fuel solenoid right before I...
Looking hard at the King Kutter TG 48 or 60 for my 2000 JD4100 CUT.
The 48 has offset hitch -- which -- in my case is a bad thing. If it was centered it might just cover the tracks. So I'd...
I'm having a really hard time finding tires for my tractor.
I have a 2000 John Deere 4100 4x4. The rear tires are 315/75/D15 or 12.4x9.3 x15
I have worn out turf tires and would like to get...
I have a pretty good idea on making and adding a port from the power beyond of my trator. If anyone would like to share complete details on all needed materials ect., I would appreciate this. I...
i looked at a 1999 jd 4100 with loader and gear trans. it has 3700 hours, starts right up when cold. no smoke, and runs out good. and no oil leaks. is 3700 hrs a lot, and what should i be looking...
So i found alittle 4100 the other day. Its in good shape(7 OUT OF 10) WITH 465HRS. Now im just wondering what its worth? It has the factory loader(53" quick detach) and a quick hitch(3 Point) with...
Greetings from Upstate NY, this is my first time posting, been reading for awhile. Need some outside advice from a bigger audience, my father purchased a JD 4100 fel compact last year with a 51"...
Hi, I have a JD 4100 and the battery light has been flickering on and off when the the pto is engaged. It just started doing it this week. I really need to cut the yard. Is it ok to mow with the...
Looking at buying a JD 4100 - 425 hours, 20 hp, 3 cycle diesel, 3 position pto, has a 60" finishing mower, and scraper blade for $8500. Says it has the extra wide lug tires, new battery, and has...
My first post...thanks in advance for any assistance.
The technical manual says that the steering cylinders are not servicable and must be replaced in whole (not repaired). However, looking at...
My first post...thanks in advance for any assistance.
The technical manual says that the steering cylinders are not servicable and must be replaced in whole (not repaired). However, looking at...
I am going to buy used, and so far I have been interested in the 2305 and the 4100 (older I know) and now the 2325.
The 2305 is out for me now because of the cat 1 hitch limitations. Is there a...
________________________________________
Below is my question orginally posted in the wrong manner. Hopefully I have also successfully added a photo that illustrates what I was describing...
I have a JD4100 that quit working. It would not start so I jump started it and after it started and I removed the jumpers it ran for a minute and then a POP sound and poof of smoke came out around...
I stupidly left my JD4100 parked outside this weekend, not realizing that last night's low was going to be so cold. When I went to start it, it cranked over, but didn't seem like the fuel was...
Anyone know what front mount snow blades fit the 4100? Need the one that is quick interchange with the snowblower. Are the blades from the 700 series garden tractors the same? Can I reference a...
Hi,
This might sound like an odd request but I wonder if there is anyone what can tell me the approximate dimensions for the quick hitch for the 4100. I'm looking at buying one of the net and...
hi
I was doing my 500 hour service and I drained the hydraulic transmission. When I was replacing the fluid with new, I by accident, put in a gallon(at least) of contaminated (old) transmission...
I have a JD4100 that's about 5 1/2 years old. I guess it's a 2003 maybe. It's the last year of production.
I'm considering purchase of an electric sprayer to mount on the 3PH. Any idea were I can...
I am looking to replace the tires on my newly purchased 4100 HST w/FEL
The current tires are to aggressive, I would like to replace but the
tire dealer indicates that to keep the proper turning...
I have a problem with the rockshaft of my JD 4100. Several months ago the 3 pt stayed up. would not lower after playing with the lever it finally worked.
I used the front end loader and put a...
I see a nice 72" NH finish mowe for sale. Would a 72" be way too big for my JD 4100 HST?
Mostly I'll be mowing fescue that's around the house.
I have a Sears riding mower now that's a 42"...
I have been looking into SCUT's and CUT's for the last year or so and have come to the conclusion that a new tractor is more than I can afford. As a result I have been concentrating my efforts on...
Anyone know if you can still find new 410 loaders for my 4100 tractor? If not new, are used ones easy or hard to come by? Any leads would be great. Thanks.
Can someone please provide the lifting capacity of my JD 4100, 410 loader?
Any suggestions as to the proper fork attachment for my equipment? I don't want to over-purchase an attachment that is...
I got my 4100 new and now when I go to the dealer to get the hyd filter they try to hand me a fatter filter that I do not think will fit if/when the front PTO is being used by the mower etc. Just...
My 4100 is cutting out. First I thought it was a fuel problem but I changed the filter etc. and have concluded it is electrical. Something is clicking right when it cuts out. It may be a bad seat...
I just bought a JD 4100 hst with 410 FEL with teeth and a 54" mmm. The machine has 670 hours on it. I have done countless hours of research on this site and many others before deciding to make...
As some of you know I was looking at the John Deere 3320 and the Kubota L3130. I drove them, both of them were great machines however, I just don't know if I would use it enough to justify buying...
I will be adapting a 72" western type (with trip springs) plow to attach to a JD 4100 and am wondering if it would be best to put it on the loader arms or on the (quick tatch?) braket where a...
I own a JD 4100 and I am having a major problem. The pto engauge is on the left and when I engaugae it to the mid or rear pto it sticks and will not go back into disengauge. So when I started...
Yesterday I went and picked up my used jd 4100hst with 410 bucket and 54 mower from a jd dealerships thats about an hour and a half away. this morning while playing wwith the bucket i noticed...
I haven't had time to check the owners manual yet but has anyone had a problem with the 3PH lower arms hitting the bars on ag tires if something (brushcutter) swings to one side?
Here's the deal. I have a JD4100 and am looking for a seat with some springs or other type of suspension. My tractor, with R4s, rides really hard. My ground isn't too smooth and I'll admit to not...
we are starting to look for jd 4100 but we are haveing a problem decideing on hydro or gear and i was wondering what other peoples experiences where with either we plan to use it for many...
I was reviewing the specs of the JD4110 since it's basically the same machine as the 4100 from what I understand, and at the bottom of the page at JD's website it says </font><font color="blue"...
Anyone know where to find a new/used/rebuilt engine for a JD4100? 3cyl, Yanmar 3TNE74. My JD dealer estimated $3600 to rebuild the engine I have, and $5700 to install a new engine. That's total...
Looking for how to diagnose the problem and options to resolve. JD 4100 has 3 cyl Yanmar engine with 1093 hours. I bought it used at 1079 hours. From 1079 to about 1088 it used about a quart...
Help me! What\'s the value of this JD4100
Wouldn't ya know. About the time I've decided I want to buy a new JD, a deal on a used 4100 comes along that I might not be able to pass up. So I ask for...
I am looking at a JD 4100 with hydrostatic drive and a 410 bucket. It is coming up for sale from a rental place that is going out of business. The total hours are between 1500 and 1600. Not sure...
JD 4100 with MMM---what kind of \"cotter keys\"
In one year I must have lost 6 or more pins that hold the mower on---or 3PH arms ect.
I have used the "hairpin" style (one side straight and the...
Anyone done this? I am assuming we all define "tilt" as replacing the adjustable 3-point lift arm with a hydraulic cylinder, so an attachment then can be tilted. Thanks for input...
Which is a better machine for heavy home use. Mosty tilling, bush hog, york rake, FEL, landscape type work? Both look good, JD is a little more expensive. I think this comparison is apples to...
Lots of landscaping to be done and am trying to decide on tractor. What are the advantages to Kioti over John Deere on these comparable models? Both are close in price range. JD is a little more...
I am interested to know if anyone has added tilt to the JD4100, 4110, 4115. I have the top cylinder, but now feel I could benefit from having TILT. To be clear, I understand that TILT means...
The story was this: The a fellow moved to Ky and things did not work out the way he had planned and he moved back to Maine. Upside for me I got to buy his JD 4100 (Gear) with FEL at a good price...
RE: possibly switching tires on my 2001 JD4100....
I am toying with switching from R3 turfs to industrial tires. This is due to almost getting stuck in two feet of snow in my side yard. I got...
Last weekend, I took apart the front wheel gearcase on my JD4100 to replace a leaking seal that was leaving annoying puddles of 90W on my garage floor.
I re-assmbled it, and the bevel gear...
I got a 4100 with 410 loader (52" bucket??) this past summer and would like to know if there is a proper weight that I should look for as a ballest (is that spelled correctly?) weight.
I have R-1...
Looking to add light kit on John Deere 4100
I'm thinking about adding some lights -typical automotive PIAA type lights (maybe 50 watts 4amps each) or something small like that. On my JD 4100 I...
Hey can anyone give me any info on how the curtiss cabs fit on the JD 4100?
Do you have to remove the handles on the fender?
Does the rear window open? If not can it be made to open without...
I have been looking at a used 4100 with mid mount mower and 410 loader at a local dealer. It has 750 hrs and has been very well taken care of. His price is 12,300. What do you think of this...
JD 4100 60\" MMM Deck Height Latch
Does anyone have pictures of the Deck Height Latches for a 4100?
I believe the latches are simply chains. My thoughts are if the latches are simply chains of...
My local JD dealer, whom I bougt my 425 from, has a 4100 with loader,mmm,front snowblower, front blade, extra set of tires and wheels, and trailer with only 165 hours, for around 17-18k.
I have a...
I saw a picture of someone's ("kennyd"('s) ?? ) 4110 with a JD cup holder on their fender and decided to do the same. I put the cup holder in the same spot on the right-hand fender, but had to...
Hello all,
I need to get a Post Hole digger for my JD 4100 (17 HP PTO)
I hoping someone here has used either Green Mfg or Leinbach on their 4100 ? what size auger and how long is the auger? Is...
Mow 5 acres but use a 620ztrac for yard. Move some dirt around and getting rid of my old 8N that I used for rough mowing and bushoging. 4100 w/410 loader 60"mid deck is $14,000 used but perfect...
I have a 2001 JD 4100 HST and I am getting tired of removing my
ballast box and attaching my RMM and then removing the RMM, etc. etc.
Is the iMatch system compatible with the JD 4100 ? Do any...
Looking for New Or Used Implements for JD 4100
The implements I would like to locate are:
A post hole digger, Front snow thrower, back blade or Box cutter, PTO rear tiller
I prefer used but in...
I am looking at purchasing either a 7500 new ($12,950 w/FEL) or used JD 4100 ($ 13,000; 250 hours, 60" MMM, FEL, turf tires, great shape). The new seems like the better deal, especially with 0%...
I am toying with the idea of selling my JD 4100 HST, with a JD
261 rear-mount mower. I only have 65 hours on it and like it,
but I could really use a backhoe now and think the BX22
might be a...
Anyone looking for a little JD out in Calif? Just spotted this 4100 (4wd, turfs, 91 hours, no loader, gear, 60" MMM) with a "buy it now" of $4500 and no reserve. Have no idea who the seller is...
I called my local dealer today asking about a BH for in my case, the 4100. and also the 4110. He said they have not seen one yet but thought JD is working on it to be competitive wth Kubota. It...
I just bought a JD4100 (Year is a 1998) at an auction and I was and I'm touching up the paint. But buying JD paint is lighter green then whats on my tractor. The JD can # is TY25309 green and...
like to find out if a set of R4 wheels and tires from JD4010 will work on JD4100 . They are different size,also different size ratio beteen fronts and rears. any help ? thank you for any input ...
I found a used JD 4100 hydro with only 149 hours that had been traded in for a 30 hp.
The tractor price is $11,000 which included a 60'' drag finish mower (Befco) and a 410 loader.
Is this...
Greetings everyone! I am in the process of shopping for a used JD 4100 to replace my current JD 316. The 316 is a great tractor but just not big enough for my needs. I finish mow about 3 acres...
Yesterday,while I was mowing my neighbors lawn the hood on my JD 4100 started flapping up and down.
This is not a normal thing to happen. I had just changed the oil a couple of days previously...
Does anyone know where I can buy a new JD 4100 w/ hydro,410 fel, 54"MMM, R4s? I live in Wyoming so closer is better! Thanks to anyone who respones for your time.
noelmsn@hotmail.com
I have a 2001 JD4100 and am having trouble keeping the tilt adjustment tight on the 3PH. It has the turnbuckle barrel and at the bottom there's nut with a piece of rod welded across one of the...
I have a 4100 and am wondering why it does not need/have glow plugs. Last fall before I bought the JD I borrowed a NH of similar size and it did have glow plugs.
Just wondering why the...
JD4110 or JD4100 with 61\" Loader Bucket
Anyone out there using a 61" bucket on a 4100 or a new 4110 that can offer up coments on how their machines handle this size bucket.
I,AM LOOKING AT A 1998 4100 WITH 895 HRS. NO ATACHMENTS. WHAT WOULD BE A GOOD PRICE TO PAY????
AND WHAT KIND OF PROBLEMS DOES THIS TRACTOR HAVE??
THANKS WOODY
jd4100 vs. 14\" diameter Spruce trees
I had three Spruce trees which were in the wrong place and had to be removed to make room for a shed this Spring. From transplanting small ones, I had...
Has anybody heard any negatives about the 4100 JD with a 410 loader? Specifically, it looks like not much really holds the loader onto the brackets. The local JD dealer said that I should avoid...
A friend may be getting new JD soon. Wondering if the new 4010, 15, models are better or worse than a 4100? What are your opinions? Why is one better or worse?
thanks,
Talked to a JD dealer today and I asked him to give me a reason (s) why i should spend the extra money on
a 4100 vs B7500HSt Here are the things he mentioned .
The left and right rear brake...
I posted a diagram to add <A target="_blank" HREF=http://www.tractorbynet.com/cgi-bin/compact/showflat.pl?Cat=&Board=custom&Number=104412&page=0&view=collapsed&sb=5&o=7&fpart=>auxillary...
We are going to buy a compact tractor. Heard that the 4100 has an alum rear end and this can be a problem esp if you want to put a backhoe on it. I wonder if it is weak, then is there the real...
My father wants a new tractor and has found it difficult to find a 4100 as the supply is low and being replaced with new models. What is his best bet? What is the difference between 4100 and new...
I have a 2yr old JD4100 with loader. What can I do to dig holes besides a shovel and sweat? Is there a solution considering the 4100 does not have a backhoe?
thanks,
I was told the 4100 with turf tires cannot accept chains. Is anyone running chains on their 4100 and if so what brand and type of chain??? The rear looks to be about 2 inches from the fender...
Been working on this project for a few weeks - fits and starts.
My neighbor is helping with the welding, fabrication, and hashing out of ideas.
The toolbox is mounted to 1 1/2 in aluminum angle...
(I posted this to "JD buying" also) I am purchasing a 4100. I have read several vague references to "problems with the 4000 series". Would anyone care to share
first-hand specific problems...
I am purchasing a 4100. I have read several vague references to "problems with the 4000 series". Would anyone care to share first-hand specific problems they've had with the 4100 model, and...
2000 JD 4100 Diesel w/60\" Mower Deck
2000 JD 4100 Diesel Tractor with JD 410 Hyd. Loader & 60" mower deck on upcoming auction Sat. Oct. 27, Hastings, MN. Go to date of sale under "Farm...
Was wondering if any tractor gurus could help me out ... will be mainly mowing approx 4 acres of flat land, 2 acres will be "lawn" the balance mainly thicker "thatch" .. I'm down to a 21D or a...
Was wondering if any tractor gurus could help me out ... will be mainly mowing approx 4 acres of flat land, 2 acres will be "lawn" the balance mainly thicker "thatch" .. I'm down to a 21D or a...
I went to look at JD tractors yesterday and am leaning toward the 4100. I've never owned a tractor so I'm not sure whether it will do what I need it to and/or what attachments I'll need. I could...
I just bought 30 acres, I will need to mow 5acres, I will have a 100ft drive, I live in MI.I will also be doing some landscaping. I think I would probably want a fel, backblade, and a 4ft to 6ft...
I want to purchase a compact tractor and have narrowed it down to the JD 4100 HST and Kubota B2410 HST. John Deere seems to have the name and a great reputation and Kubota seems to have a great...
Ok I think that I am real close to getting my new tractor finally. BUT I still can't make up my mind on these 2. They both have hydr. and loaders. But the jd has 40 hrs. on it. It still has full...
Great site! I am new to the country life and everything that goes with it. Was able to buy this coool shovel for the driveway though. Hope to learn a lot of the "tricks-of-the-trade". Keep up...
In cold weather 0-20 degrees, how long once starting my jd4100 should I let it sit and warm up? It is in shed so I usually have to back it outside immediately after starting so I don't die of smoke.
I was trying to find out how hard I can pull using a 5/16 chain behind my new 4100 using the drawbar? For pulling small trees out of the ground? Can I leave a little slack and drive away and...
The kubota controls appear not well thought out. Foot controls appear an afterthought. Why is weight of kubota lighter? Warranty seems not as good? Am I missing reasons to buy the kubota over...
I am in the process of buying a JD4100 with 54" loader and ballast box in rear, 60"deck. To remove snow how is using the loader? What is best technique? What is the best low cost easy to adapte...
I will be mowing about 3-4 acres, mostly open and want to remove snow from about 600ft driveway. Other uses around the home will vary. What is the best tractor for around 15k? Kubota vs. Deere...
IT is the best little tractor there is. I do everthing with it and its powereful.IF anybody agrees with me about the john deere 4100 AND LIKES IT, post that you do. PLOWER
I am looking for a replacement for my JD425 garden tractor. I started looking at a 455. While at a dealer Friday looking at a 455 they had a 4100 setting close by. I decides to drive it and drove...