2023 Kubota B2601 with 40 hours Bh70 Backhoe LA435 front loader Land Pride RB1660 rear blade Kubota BX2830 commercial snow blower Chains front and rear Led Lights front and rear Titan Steel Forks...

I only have hilly terrain. the property is a series of stone push up benches and the short flats between. Due to this, I tend to move around on the seat quite a bit to stay centered on the...

I was using the York rake trying to improve the steep uphill drive to my place. it's about 1000 feet, and the winter time and truck traffic (garbage, fuel, delivery etc.) makes for a bumpy ride...

Purchased the kits last fall, but with winter, never got to the task of installation. First set is a straight directional control valve, the second set is a DCV with float. I think that...

It is no longer winter, so I went about putting the blowers and blades out of the way on pallets. I took the opportunity to install the Pat's adapters to the Kubota B2601 as the extra length is...

I know this has been talked about often. Does anyone see issues buying a low hour 309 B2601 it is a 2018 model with the L434 loader, 60" belly mower and rear quick connect. The new one has the...

I see pluses and minuses on both. Biggest grip about B is poor seat and location of gas filler cap. Biggest minuses on BX are lower ground clearance reduced lifting and engine having to run higher...

Hello and thanks for any help in advance. While clearing snow with my Kubota B2620 the rear level control lever stopped working with my snowblower all the way up. The lever is all loosey goosey...

I am looking at replacing a John Deere 855 with a 380 frame mounted plow. Does anyone have the Kubota B2601 with the 4 point hitch (B3410 for B01) and the 60" HD front blade (BX2812A)? I would...

Less than 300 hour, 10 years old. Pictures do not make it look beat up, The asking price is what they cost new then. OBRO. I want to move up from the 2wd B7200 HST that gets "yard and...

So next project is going to be some protection from falling limbs, branches and to help protect me when I flop her. (Not if.... I have rolled and flopped too many vehicles to not do it eventually)...

Hi all, Does anyone know if I can use a Kubota FS1000 48" Tiller with the Kubota B2601. My son in law lent me this tiller and I want to be sure that it can be used before I unload it off the...

So talked to salesman he said it's typical, so keep travel pin in. I've never had hydraulics bleed down unless an external leak (don't see) or internal leak by a spool valve with junk. Is this...

I am searching for 3-4 inch wheel spacers... Can someone tell me what other kubota models have the same lug pattern and fitness as my B2601? Thanks

What hydraulic side link are you using for a Kubota B2601? I'm adding Top&Tilt and found the appropriate hydraulic top link at Summit, but they didn't know what side link to provide. The side link...

Hello Everyone: I have been a Kubota owner for quite a few years, starting with a BX2380 and now a B2601. I loved my BX2380 and ended up with about 350 hours on it before selling and upgrading...

I've got a B2601, and theres a good deal for a RCK-54-24B nearby. I know this isn't my model (RCK54-34). What kinds of issues/modifications should I expect if I try to make this work? Is this a...

Time for a coolant change on my B2601. Does anyone know if there is a plug or something on the engine to drain the block. I would guess that just removing the lower radiator hose, you would still...

I have the factory third function with the two buttons on the front side of the loader joystick where I hit them all the time. I thought I would get used to them but I don’t seem to be getting any...

I have used both belly and 3 point mowers on other tractors. I get the annoyances and benefits of the two types. My question is this: I have a really soft yard. Which is less likely to tear up the...

Well, I thought I'd submitted a review of the B2601 in the Reviews area, but I made a mistake on the hours. Went to correct it, and it was not there. So, I'll sumit it here and let the guy(s)...

Getting ready to sign the paperwork for new B2601 and suddenly I get an “Oh by the way” you cannot use the mid mount mower with the factory wheel spacers. In the original online build it prevented...

Friend has 100 acres but "usable land" hardly none. His main use would be to fix up his steep gravel driveway. I would guess that R1/ag tires are a must for traction. The tractor is pretty...

I bought a used LandPride finish 3-point mower and need a PTO shaft for it. Raised, it is 34" from gearbox shaft end to end, and lowered it is 35". I'm assuming I will need to cut anything I...

Went to go mow next to the road this morning with my little kubota. Tractor got a little stuck in the muddy ground. Backed out and saw what looked like water on the ground. Dismounted and saw...

I have a 1100 hr B2150 that other than a slight oil leak from the steering seal runs flawlessly. I do also need a new gearbox on the mowing deck. But other than that she starts every time and does...

Need some advice. I have a 2013 Kubota BX25D with front snow blower and mid mount 60" mower with 455 hours on it. Went to dealer today and I can get obnoxious amount of $ for it. I use it for...

I have 3 acres to mow, i use a 60" mid mount mower on my B2601 it takes me about a hour 20 min to mow the yard. I have been told a zero turn could cut that time in half is that true? When i mow i...

The B2601 was delivered this morning. $11.44k difference for it plus 5 ft box blade and added hydraulic on FEL and JD 2025R 2015 trade-in. $13k for the JD. He had a buyer up there (Winchester)...

Hi All- My B2601 not starting; traced the issue to the 10amp fuse tied to the headlight panel. Tractor starts and runs after disconnection of the multi-lighting switch. After further recon, found...

Got a dumb question. I have a B2601. The three-point hitch lift only seems to engage when the lever is in top of its range (7-8). I've had it for a couple of years and I don't remember it having...

I purchased this B2601 used. The backhoe was on when I purchased it 6 months ago and I just got around to taking the backhoe off and installing the three point. Are these stabilizer arms bent...

Sold our BX2660 that my wife used to cut grass and went with a B2601 with a 60" mmm, FEL and 4' box blade. I wanted to work under the tree limbs and tight quarters that my Grand L could not fit...

It’s been too long since i’ve been on these forums. Last time I was on here I was complaining with other JD 2305 owners of the poor design of the transmission/PTO. So after yet another major...

What is the maximum size wheel spacers you can use on a B2601 that will clear the 60" mmm? Thanks

Greetings, I’m looking at new a B2601 but I can’t take delivery until August according to the dealers in our area. I would be willing to consider a like new preowned unit if the price was fair...

Hello all, My first of many questions for the group. I have a BH70 on a B2601 that I want to take off. I've watched all the videos of removing other models and it seems pretty straightforward...

For our new 10acre lot, I am looking at a Kubota b2601. Would be used for landscaping, snowplowing, mowing, and clearing. The equivalent kioti seems to be the ck2610. Given the extra weight of...

I'm curious to learn if it is possible to remove the Front End Loader without the Bucket attached and if the Loader assembly will remain stable if stored without the Bucket? The reason I'm...

What a wonderful find for a new owner to discover this site. I recently bought a new B2601 loader tractor with a ballast box and a plow. My driveway is 100 yards long with a parking areas of about...

Big day finally arrived. When I got the call the tractor was ready I caught on to the fact they kept saying "Box Blade" and I had ordered the RB1560.......rear blade....well honest mistake they...

I'm working with my dealer on pricing both the B2601 and LX2610 (ROPS, not cab). Initial purchase will be loader/bucket, grapple, pallet forks. Maybe a flail mower or LaneShark or both. Trading in...

While on one hand I cringe a bit with RevTurbo's experience this week with his 2601 delivery (sounds like the dealer is making good) I am happy on the other hand with the fact I just put a deposit...

Well, after about a 3 months of shopping and a month of waiting for it to show up, my new B2601 was delivered Saturday. I bought basic implements, FEL, QA bucket, belly mower, quick hitch, pallet...

So I got in my first local quote for the 2601 with the list of attachements/options below. They literally quoted MSRP for everything which comes to $28,579. I then asked them to load the rears...

Found a used 2019 B2601 with FEL /BH that is what I am wanting but it is 350 miles away, was wondering how much I might expect to pay to have it transported to my place? I do not have a way to...

How does a Woods RC4 compare to a similar LandPride orange 'bush hog'? Or, what rotary mower - bush hog - shredder do you recommend for a B2601 and what is a reasonable 'street cost' for it...

I plan to take down somewhere between 100 and 200 trees and dont really feel like having constant burn piles, so I'm thinking about getting a chipper. Do you have any recommendations for one? Thanks.

Hi All, Have just started kicking a few tires. I contacted three VA Kubota dealerships and one got back to me with a quote. I wonder if a B2601 for $15,000 and a LA435 loader for $4,225 and a...

Ok, so I had a BH70 backhoe added to my Kubota B2601 since I have so many digging projects. It may be my imagination, but it feels like I have lost some lifting power from FEL in terms of...

Is the rear PTO housing on the Kubota B2601 HSD steel or aluminum?

Has anyone relocated their hydraulic connections to the same position as the new models? It will save some skin on the knuckles.

Hydraulic Auger Would like to get a Frt mounted post auger for my B2601 with a 434 quick attach frt loader on it. Posts and Shrub planting, would like 12in aug if possible. Anyone have experience...

I知 ready to buy a B2601, but noticed a couple odd bits about it. The bx models have option for bolt on cutting edge, yet the bigger B models don稚. Does anyone know why? I run heavy equipment, and...

Anyone have a 60 inch mid mount mower deck for a B2601 they can take a few measurments off of? My dealer, nor Kubota Canada can answer my question. I want to know if the RCK60-29 from my 2013...

Hi All, So really enjoying and getting good use out of our B2601. At around 15 hours currently. Looking to get an auger 3PH attachment. Pretty sure I want one of the Everything Attachments...

I originally posted this as a reply to another thread, but I guess it was a dead thread because I didn't get any response so I will repost. I have a BX2370-1. Love it, its been great. But now I...

New member here...been lurking for a month or so. Like many here I am new to the compact tractor market. Would appreciate the collective wisdom of the group(I have scoured them a bit for data on...

B2601/LA435 Quick Coupler Leaking Got a new tractor a few weeks ago. 2+ hours on it. Checked the fluids and found the transmission really low. Then saw a puddle of hydraulic fluid under the...

Title pretty much says it all. Picked up a new B2601 w/loader over the holidays. Need a box scraper for driveway maintenance. About, say, 700 feet. What would be the optimum size? Thanks, -Steve

Well at the tender age of 72, I suddenly discovered I needed a tractor. Seems the 70 acres or so I've got are just not willing to mow or clear themselves (dang ingrates), so I have to do it...

I recently started using my new B2601. The treadle pedal is very hard to press forward or reverse. Is there some adjustment to make this easier? My previous tractor was a Power Trac 425 that had a...

I'm going back and forth on the two. What are the major differences? From what I can tell is that the B2601 has low mid high gearing and 2025r has low and high?

I need a smaller tractor bigger than a BX on my 40-acre homestead and out on the farm. The BX's I have use have too little ground clearance, tires are too small for a pasture, and they lack...

I want to down size on tractors. I currently own a John Deere 3320. Nice tractor, no complaints with it. I've used it about 1,000 hours. Mostly have used it for snow removal. Did some digging, and...

I rented a kioti cs2510 today as I can't rent the Kubota that I'm interested in. I did some simple work such as moving some rocks, ground work, etc. It seemed like it have a VERY difficult time...

Help me decide, Kubota L2501 VS Mahindra VS Kioti Hello all, New member and first post here I come from a hobby farming background ( 100ac in total, 63 ac workable and 27 of carolinean...

I just took possession of it a couple of weeks ago and have hardly used it. I removed the FEL a few days ago and went back to reattach it and somehow got it out of line with the receiver and the...

Does anyone know if the RCK60-29B deck that was used on the B2920 (among others) will fit on the B2601? I realize the new deck model # for the B2601 is RCK60-32, but just curious if the RCK60-29B...

What are the brakes all about on my Kubota B2601? I've changed out brake pads and shoes many times on my cars and motorcycles. What type of brakes do we have on the B2601 or B Series? Why am I'm...

Hello all - I don't post much as I'm not much of an expert on anything, but I research a lot so I've read a lot of the threads on TBN. Love all the input that is found on here. Here's my...

Guys, I have 13 acres of mostly woods and just enough grass for a push mower (no tractor mowing needed). The property has lots of water issues and trails that need constant maintenance. I also...

Has anyone done theirs yet? How many drain plugs are under the B2601 for the Trans & Hydraulic fluid? The manual is so confusing. I don't want to remove every single bolt underneath the tractor...

I picked up the three filters needed for my 50 hour Service. Oil, Trans, Hydraulic. Reading the manual, it does not state which filter goes where. No part numbers #'s or location specific. The...

Looking for some info that is not stated in the Operators Manual. ""Oil Transmission (HST) Hydraulic"" Three filters that I need to change at 50 hours. There's no part numbers for these...

I have two Kubota tractors - a BX2370 and an L3560. The BX2370 has a 60 inch MMM and it's what I'm currently using to mow about 6 acres of my hilly, rocky property. I put the mowing deck all the...

Been debating for some time now between a B2601 and a B2650. Currently have a BX23 that I use for mowing, loader and backhoe work, nothing else. But I'm finding I need more ground clearance, more...

I am considering changing my front tires to turf. Will there be a circumference difference between a R4 and turf 23X8.50X12. Also they will be 6ply for load rating.

My buddy at work has a 2018 Kubota B2601 and he was telling me that he is unhappy with the weak loader and general poor performance of the loader hydraulics. He was saying that he is considering...

Hello, I am buying my first tractor and enjoying and agonizing over the search. I would use it for maintaining 150' gravel driveway (snow removal in winter/grading in summer), cutting and...

I am about to purchase a Kubota B2601 and would like Top and Tilt with a Hydraulic Box Blade. My dealer thinks the B2601 is too small for all of this without removing a fender. Is he right? I have...

I have a new B2601 which I have been doing upgrades on. I also have the BH70 and the rotating driver seat. My issue is the seat only has two springs under it for cushion and they stink. The...

My buddy has a newer B2601 that he wants to put gauges on and check/shim his loader hydraulics. As is his performance from the loader is such that he will stall out hydraulic lift/curl before ever...

Back to the forums for some advice. I have a Kubota L4701 with some heavy duty attachments that I use on my 60 acres. It is a mix of pasture, scrub, and heavy trees. I must say it is a real...

Can anyone look at their B2301/2601 with mmm and take a picture of the orange link that runs from the 3 point arm to the mower? Mine is broken and I think it was installed backwards . I have...

I have a B2601 without a loader and want to put one on it. The LA434 seems nice, but I know sometimes there are aftermarket solutions that are just as good for less money. What are my options for...

I am thinking of upgrading from my BX2360 to a B2601 and test drove one at my dealer and was surprised to feel how stiff the HST pedal is especially in reverse. It felt like I was trying to drive...

Thinking of moving up from my BX25D to the next size tractor the B2601. Main issue is space in the shed. Anyone know the LOA of the BX when parked from the tip of the loader bucket on the ground...

Hi Everyone- Newbie here. Just took delivery of a Kubota B2601. :-) Im getting ready for winter and doing my chain homework. I will need chains for sure. Has anyone out there had to put...

I just took delivery of my 4th Kubota B series, a B2601. The tractor runs great and performs well, however the HST pedal is very stiff forwards and back. I can not find any grease fittings to...

Just bought a 2016 B2601 with several implements but no bush hog although it does have a 60" belly mower. I know I can't cut down saplings like the BH, but I want to know how aggressive an...

I have had the machine for a little over a year, not a bad machine, but do not use it like I thought I would. More mowing than anything. I need to get a rough idea of what I could sell it for...

I've currently got an older BX2350, ex a contracting outfit. I got it cheap at auction, it's pretty beat up, but mechanically seems sound. It does most stuff I need, although I occasionally wish...

Have 6 hours on my B2601, the one thing since new is the frt loader bucket is not parallel to the ground. It about a inch or two higher on the left then the right when off the ground. Lies flat...

I realize this is a silly question but does anyone know what makes the B2601 3.7" wider than the B2301 (as listed on the Kubota website)? I'm guessing it's just the larger Ag tires which are...

Good news and bad news for this purchase for me. The good news is that on 7/5 a new B2601 with FEL, 60" bucket, 60 inch belly mower, grill guard, accessory ROP lights, with liquid weight in the...

I'm ready to go to my dealer and pick up my goods to do the first service on my machine. Looking at the manual..." Four Gallons " for the Transmission. Really? Is this a misprint? I'm accustomed...

hey guys! i just got a new b2601. i would like to make her a little more stable. id like to make here 4-5 inches wider... is that too wide? what model number and where should i get these? -thanks

I am getting ready to purchase a new Kubota 2601 with a snowblade and power angle. The dealer indicates the 72inch would have to much side push and will slide the 1600lb tractor. The 60 inch just...

After going through our less than winter winter. Comparing it to our old B7510, The good: More power, cup holder (not the best place, but we have one), quieter, mower seems to go on easier (I...

HI everyone I have finally decided to buy a New B2601 and it will be delivered tomorrow, Have been looking for about 9 months and it all came down to price and comfort. There is a JD, Kubota...

i am in south east pa. i found a price for 18700 with rebates on this machine with fel and mmm. What do yall think? i also have a 2008 nh tz25da with mmm and fel w/ 775. i was offered $6k for...

So... I backed into a stump and broke my hydaulic filter housing... The steel line that runs from the filter housing to the front of the tractor appears dented and bent a bit too. So, I'll be...

Replacing a 31 year old L2250 gear Tractor with a B2601. Want a Backhoe to plant trees, put in a couple Koi ponds and replace a field drain tile. I have 16 acres total with 3 acres of grass, lots...

So we are getting down to the wire in making a decision on a tractor for our property. Mostly cutting grass, a little food plot work and some front end loader work. We are getting a: 60" pull...

Ive settled on a B2601 to replace my 1985 L2250 which I've had since new. 60 in mmm, 60 in QT front loader and 70 series BH. Several questions to start. No experience with suspended deck, been...

Hello, Long time reader, first time poster. I'm looking to buy a tiller or disc for my Kubota B2601 19.5 PTO HP. 540 RPM. I'll be breaking around 2-3 acres and I'm torn on what to get. A...

Kubota B2601 with industrial tires with FEL 54" Bucket quick connect, Land pride 48" Box scraper, Land PD10 Auger and Tow ball hitch $18,000 Taxes not included! Good, fair or bad deal?

I will be buying a grapple soon for my B2601. It will be either the EA wicked 50" single lid or the Landpride SG0660. The main duties will be manipulating oak cuts as pictured below and servicing...

I switched out my old rear control valve in favor of the Kubota OEM valves mainly because I needed float on one of the valves for my flail ditch mower. Here are (hopefully) pictures of the old...

The temperature needle on my B2601 only goes about a quarter of the way up in the summer and stays down in the cold marked area in the winter. Can anyone of you B2601 owners tell me what...

Picked it up today, B2601/54"mmm/60" SSQA Bucket/Front Remotes/BH70 Backhoe/Loaded Turfs!! Can't wait to start putting her to use, maybe a foot of snow coming on Thursday to play around in, but...

is this a quick/clean bolt up? anyone tried it? please with results? I sat on a 2601 recently...seat was impressive by comparison.

Hey everyone, This is a tough one. I'm getting ready to pull the trigger on a new compact tractor and have narrowed down my choices to either the Kubota B2601 or the Kioti CK2510, both with front...

Hey everyone. Off hand, does anyone know what the weight of a B2601 with LA434 FEL and BH70 BH attached? Will be shopping for a trailer soon. Thank you!

I got first quotes today on a 2601. With just a 60 in mmm.(list $18,316.00)$17,212.00 delivered. With qd 60 in FEL and BH with 12 in bucket and mmm.(list $30,239.00)$29,456.00 delivered. Am I...

I will be pulling the trigger on a new B2601 FEL, BH, And MMM as soon as I decide on which PHD is right for me. I had my heart set on the Landpride HD25 SSQA/tractor mount and 12" auger.($2300ish)...

I dont actually have my tractor yet, but i should have in a couple weeks. Currently have 5 acres of mostly wooded with some grass/cleared area & need to do some cleanup. I lurked around for...

First post and I'm stuck between two models. I worked on a cherry farm half my life so I've driven a lot of tractors, but I've never had to buy one myself. Now I do and I don't know enough to...

So I've been trolling around on here for a few months as I was looking to finally upgrade from an old Yanmar 1500 to take back my property with. Shopped around for a while and ended up ordering a...

Wondering if any recent buyers could give me an idea of what they paid for a 60" mmm on a B2601 OR a B2650? Short version, I think my dealer is leaving out a $500 rebate I was promised and...

B series: need advice asap I'm days away from trading in my bx2370 for a B series and need to choose between the 2601 or the 2650. My biggest question is whether I'll be happy with the power and...

I am trading up to a B series from a bx, and was on the fence between a 2601 and a 2650. I was leaning towards the 2601 until my old neighbor went down to the dealer with me and talked me into the...

I have a few questions. My dealer tells me I need to figure out if the Backhoe is open or closed center. Does anyone know? They say I cannot use an open center valve. Also does anyone know which...

I went back to the Kubota dealer this morning to inquire about a larger frame than the BX25D. I ran the B2601 they had on the lot and really like the gear drive. But looking at the Kubota website...

Hello Orange enthusiasts! Ive been researching to buy a new Kubota so naturally that means i've also been scouring the interwebs devouring as much info as possible. After all, research is fun...

So, I'm talking to my dealer about buying either a BX25D or B2601. From what I gather, you cannot raise or lower the MMM if the BH subframe is in place. They recommend having either the MMM or...

I grew up on a Farmall 150 and Cub. Fast Hitch is all I've ever known but the family Farmall tractors are wore out and frankly, we don't plow and plant big fields anymore. Two groups of...

With 2.5 acres, it seems a SCUT such as a Kubota BX-25D will handle all my mowing, digging, and other needs. After narrowing my choice to a Kubota BX-25D or a Massey SCUT, I realized I had...

Sharing for the common good. I received a message from Weidmann Bros. when I asked about the availability of a cab - they won't have the hard top cabs ready until spring. Looks like I'm in for a...

As anyone located extra wiring for work lights like the BX and other models have? I looked under the fenders and didn't see any obvious extra connections.

I took delivery of a new B2601 with a Canopy, 54 inch MMM, Quick Attatch LA434 loader with 54 in bucket, and a set of Woods QA pallet forks. It was kinda sad to see my BX1860 leave, but the...

Good evening folks, I live outside Colorado Springs and am looking to buy a new Kubota 2601 with FEL and 50" tiller. Here is the price per my local dealer: B2601HSD 26HP 4 WD Tractor with...

With winter around the corner, I'm looking for a snowblower for my B2601. The dealer is suggesting a B2782B (63 inch). The Kubota Canada website doesn't list that model, and lists the BX2750D as...

Went to a Kubota dealer yesterday and looked at these two models. I will plow snow and do light maintenance on the property. The brochures for both models talk about "newly introduced" and "newly...

Yes, I know it doesn't count until there are pics... Delivered today. Got to spend an hour playing with loader and brush cutter. I am going to really enjoy this. May get back out to the property...

Got 0% approval and dealer is getting my(our) new B2601 in the next couple days:dance1:. I have the best wife ever:D. She got on here, read a bunch of posts and said no Branson and BX is too...

Dealer said i can get one with a loader for $17,000 new and if i get another implement i can get 1,000 off. I asked for the B2650 but for some reason he ignored my asking and gave me the price of...

I like the idea of having a backhoe, but to do so, I'd have to settle for a slightly smaller tractor in the BX25D......adding a new BH to a B2601 would take another ~$7K....yikes......here are the...

I'm a big guy that is looking for a tractor to handle mowing (3 acres with hills and slopes and plenty of obstacles), FEL w/quick attach bucket for moving mulch, topsoil, and relocating snow...

Neil Messick sent me this yesterday. Still putting her together but I think she looks great.

Well I finally pulled the trigger on a new tractor. I signed the papers today for a B2601 with FEL, 60" QA bucket, I added a rear hydraulic remote and the 20 amp alternator. While my tractor is...

Hello, I am looking to get my first tractor. I have 17 acres. About 1 acre of lawn, 5 acres of grown up farm field, 5 acres of wood, etc.... Looking to mow, take care of snow, bush hog...

hi All, getting within a few months of making my tractor purchase. I am struggling a bit with my decision and here is why: 1. I have hilly property and I want to be able to use the tractor on...

I went down to the Kubota dealer last Monday, thinking I was going to buy a BX25D but looked at a B2301 and decided to go that route instead and ordered a B2601, while we were doing the paperwork...

I'm looking for opinions from anyone who upgraded from a BX25 to the small size B, I'm specifically looking at the new B2601. It's more money than I figured it would be to upgrade after talking...

Hello everyone... I'm in the market for a tractor, and came across a couple threads here discussing Kubota's new B2601 model. I was looking at the B2620 previously, but after learning about the...

Yesterday I learned that Kubota is introducing the B2601 in 2015. Looks like a nice tractor with new improved ergos. I'm considering trading in my ZD326 for one. My ZD326 is a 2014 model...