kubota b7500

Head lights bulbs have finally went on my B7500. Just curious if anyone has replaced the headlight bulbs with LED bulbs. If so, make and part number would be greatly appreciated. I think it would be an improvement on light output.

2001 Kubota B7500 Hydrostatic Drive, 21 HP, 4 WD Tractor with 1171 hrs. Purchased from Hurst Tractors, Marietta, OH. Tractor has a 4 ft. bucket and is capable of lifting 700 lbs. The hydrostatic drive offers two ranges, H & L and is very easy to operate. It has a mid PTO for a mower deck and...

Hi All, Does anyone know of a vertical exhaust kit for a B7500? Many thanks!

Hi.just recently had the front 4x4 shaft with the for lack of a better description u joints replaced.goes from front of the transmission to th front axle .well the mechanic forgot to put back on The cover that goes over the shaft .how important is it.thanks

Hi everyone .hope you can help me out. a shop in my town worked working on my Kubota b7500 he said he had these two springs left over not sure where they went or if they was mine they're definitely unique looking. hoping somebody can identify and help me with them thanks so much

Hey Guys, new member here Purchased a B7500 with just over 400 hours a while back. Yesterday was running the MMM and tractor was losing power and realized the tractor was low on fuel (I know dumb mistake) but it did not run completely out of fuel, it did sputter some and immediately shut it off...

Hey guys, just purchased a new to me Kubota B7500, pretty clean tractor with 400 hours, 60” mmm, 2 sets of tires (turf and construction/ag) I believe it’s a 2006 year model. Also picked up a King Kutter 4’ rotary cutter the same day. But anyway, I’m a first time tractor owner but have grown up...

I've had my tractor for almost 20 years and it has always been reliable. Yesterday I parked it and today it will not start. Thanks to this forum I have troubleshot the safety switches and found the clutch switch plug broken and not connected. There is also a wire disconnected from the solenoid...

I've had my tractor for almost 29 years and it has always been reliable. Yesterday I parked it and today it will not start. Thanks to this forum I have troubleshot the safety switches and found the clutch switch plug broken and not connected. There is also a wire disconnected from the solenoid...

Is their a good aftermarket replacement ty.

Started my trusty B7500 only to find the thermostat reaching red zone. coolant was empty! When I first added coolant, it came out of one of the holes on the side the engine block which typically has a sealing cap on it. I found the sealing cap and re-installed. I suspect I didn't have enough...

Hi all. I have a B7500. I made a plow mount for the front loader and attached a galvanized 6ft plow I was able to buy. I used it the first year with no problems but wasnt able to complete the installation of any angling mechanism. This year I decided to take this up and wanted to use a double...

I have a 2002 Kubota B7500 with a rear mount Woods Backhoe. Love it, best tractor ever. I need to replace the right rear axle cover. cracked outside bolt holes. I got the new cover and the Permatex arrives Thursday the garage space is cleaned so this is Saturdays project. I wanted to ask a...

I'm replacing the arms and shaft for the 3 point hitch. Seems I stripped the teeth off the arms and had to go internal to confirm if any other damage was done. Have questions on reassembly position of the internal piston/arm and and the two outside arms. Any knowledge out there?

The Tach-N-Go Quick Attach from WWW.MYTRACTORTOOLS.COM is now available for the Kubota B7500 tractor with LA302 front end loader. I have the first production model installed on my B7500, along with a set of 42" quick attach pallet forks, also from MYTRACTORTOOLS. My existing OEM "Square...

Morning, I have a B7500 HST with a 302A loader which has recently started to leak gear oil from the front axle. I know I have a leak from the top seal on the portal axle and I do know how to fix that one. My second and more serious leak is coming from the pivot mount where it bolts the axle to...

https://www.tractorbynet.com/forums/kubota-owning-operating/418647-2003-kubota-b7500-mid-front-2.html#post5723768 Scroll to post# 20 PS How can I change the thread name to a more general title so I can keep all my mod posts together?

I need 2 front rims 6-12 and 2 rear rims 9.5x16 for my tractor..... with or without tires, new or used and it just don’t matter if orange or pink! bo.mccarty@theboman.biz or 606-831-1266

Can't find any spec on a Kubota B7500 positive battery cable. Need to know the length and gauge, please. Have to order one with dealers shut down, and don't have access to my manual. Would appreciate some help. Thanks.

I came across a used B7500. The engine starts and runs just fine but I have been unable to get it to move forward/backward. Hydraulic fluid looks good. I'm new to tractors and don't know a whole lot. Any suggestions on what to check next would be greatly appreciated. Thanks.

So, my son has a B7500 with loader. He found a snowplow on CR for free so, of course, it has to be fitted to the tractor. He did a nice job of designing and building all of the necessary hangers, etc to attach it to the tractor and everything fits just as it should. The snowplow has hydraulic...

Hi everyone I posted a thread a few months ago about a front mounted rotary broom. Here it is https://www.tractorbynet.com/forums/kubota-owning-operating/413784-front-sweeper-b7500.html?highlight=b7500+mid+pto After going through some headaches on sourcing the right parts and spending all kinds...

I have an LA 272 loader that doesn't come with the upper portion of the front grill/brush guard. I had some scrap metal and decided to make one. I also was unable to find a 4" LED light to fit the existing headlight housing so I also installed a light bar that I got from harbor freight. Im...

My fuel gage and temperature gauges are not working so I tried to access the control panel but I just cannot see how to take it apart without possibly breaking some plastic clips or the like.......any suggestions?

Hi All I have a 2033 b7500 hst tractor and I bought a used front sweeper and a quick hitch. For the life of me and after talking to messics and my local dealer and posting on another forum, I cant figure out the missing parts to make it all work. Do any of you know what parts I need to compete...

Randomly my manual transmission B7500 stops running for no apparent reason. It happens when you turn it off after using it. Does not matter if it has been running a short time or a long time. When this happens, you turn the key, the dash lights come on, but nothing, no starter, no noise...

Hello all. I've had a Kubota BX2350 for about 5 years now and it has been an excellent tractor for most all my needs. I purchased a used B7500 to help out in the duties. I am having a hard time finding a manual for it as it has a few issues that need addressed. First off my fuse block had a...

Hi, New member. I know this topic has been covered before but I am overwhelmed trying to find links. My 1998 Kubota B7500 tractor worked one day, now doesn鬩 make a sound. I have done all the usual. Had the battery tested and it is strong. My father in law jumpstarted the tractor at the...

We purchased a 70 hour tractor that had been stripped of parts, we needed the motor and nothing else. Now we have the remainder of the B7510 parts to sell, Hydro trans, front axle, rear axle, rear fenders, tires and wheels, etc. ....open to offers. The motor we removed purse like a kitten, the...

I have a 2004 Kabota B7500DT with 409 hrs on it. I bought it new with the below accessories, all new: 1. LA302 FL loader 2. B4672A Kabota Backhoe 3. Big Bee KRC48 48 Mower 4. Howse BB48 48 Box 5. RHINO. HR750. 50 Tiller 6. RHINO RPHD. 9 Auger I AM WONDERING WHAT YOU THINK THE VALUE ALL...

The bucket on our B7500 has seen just over 1000 hours, many of those were scraping manure, or clearing the driveway. It has also had mud, snow, manure, etc left in it more than a few times. As a result, the bottom of the bucket has worn out: As you can kind of sort of see, about two-thirds of...

My sister has a B7500 that somehow someway either blew a head gasket or cracked the block as there is now water in the oil. Unfortunately it was run hot and lunched the motor, her tractor has 200 hrs +/- on it.. but has been neglected and left outside over the years. ..dealer estimated 9K to fix...

Anyone have experience with a B2781B Snowblower on a B7500 HSD-R with LA302 FEL? Specifically, does the Brace for the LA302 need to be removed from the tractor, to be able to mount and/or operate a B2781B with B2733A Male Quick Hitch and Subframe? The Brace is Item #4 in Figure G-5720A on Page...

I have a B7500 subcompact Kubota tractor. Everything was running fine. Then about a month ago it sat for 2-3 weeks during heavy rains. When I went back to start it, there was black smoke at startup, then it ran for 15 seconds or so and quit. In trying to start it again right then, I see...

hey guys trying to sell my b7500 and wondering what you guys think on the pricing. I think the numbers are right but could use a sanity check. clean b7500 979hrs, hydrostatic, 4wd not sure on exact year but they were only made between 2000-2003 front tires have some cracking but hold air fine...

Seems i have a small spring inside the frame broken causing no tension on pedal. Anyone tried this repair? Pedal has no tension at all forward or reverse.

Had this Kubota B7500 for a short time, and wanted to check tranny fluid. What could be simpler, right? Strangely enough, the dipstick will not pull out. Thought that maybe it threads into something, so rotated both directions many revs, no help. Rotates by hand with minor amount of...

After 14years and 941hours I sold my B7500 and have decided to go with a Hydro L2501. No regrets what a great tractor. Original battery and NEVER visited the shop. I no longer use a tractor to mow the lawn and will use L2501 for fire wood, skidding logs and snow. I want something a little larger...

We have a Kubota B7500 which has had a sloppy loader control for as long as I can remember, it got to the point where the lever hit the steering wheel when you went all the way to the left (full curl). I finally got tired of it today, took it apart and replaced the bushing for the pin that goes...

I have a B7500 and I recently purchased a subframe model B2733. I was told that to run a snowblower I need the mid mount pto shaft kit, which is not made for my tractor anymore. From reading the forums I have seen the B2750D and BX2750D blowers will work with my tractor (at least for the 7610...

Would you consider 6500 to 7000 a fair price for a clean kubota b7500 mid mower deck, with around 560 hours and no fel. also has rear blade

I have a question I am hoping someone out there in Kubota land might be able help with. I used my hydro B7500 about two weeks ago during 25-35 degree weather with no issues. Then, after not using it for a week, I took it out again, but the temps were now in the single digits here in RI. It...

Anybody have a cheapish idea as to how I can get rear hydraulic remotes on my tractor so that I can operate a 3 point log splitter? TIA

Hi All, I'm new here and have a question regarding my Kubota B7500. I just took delivery this week and already move the rear wheels into there narrowest position along the axle shaft. My pin and axle tightening thingy ma jig is located on the inside of the wheel. I've seen a video showing...

I have a 2007 BX 2350 with 400 hrs with no front hydraulics and was wondering if you guys think it would be a downgrade if I traded it in for a 2002 B7500 with 450 hrs and a FEL. I love my BX but want a FEL. Thanks

I'm tired of the exhaust deposits from my B7500 covering up my front loader, hydraulic lines, etc. Can I add a short piece of exhaust pipe to divert the exhaust a little? Is there an easy to get this black stuff off? Ron G

Hi, My B7500 is an HST. Front Loader, 5' blade, carry-all, Goosen Chipper/Shredder. 3 1/5 acres, very steep. Tractor primarily for hauling, timber felling and winching, grading roads and terraces, and plowing snow for neighborhood along 1.5 mile drive. I'm far enough away from the dealer to...

Replaced a hose on the la302 fel and now the bucket will not move up, removed hose and the hose is not blocked. Any ideas? Do I need to bleed the lines or the valve on the fel? If so not sure how to do this.

Hey all, Im an avid RP fan and use all of their products in all of my equiptment. So, it was a becoming frusterating when I couldnt find a replacement RP engine oil filter for my B7500 - tired of dealing with my local kubota dealer and theyre nearly $20 when shipped online. So I finally spoke...

Hey everyone, Im thinking of a new upgrade for my B7500. I found an axial 12V fan that runs 250cfm and .053psi @50cfm. The goal in putting this fan on the intake of my Kubota B7500 is to negate the pressure drop over the air filters. So, heres the question, does anyone know if that'll...

My sister owns a B7500.. I'm guessing a 2003-2005 era model. Well... They have not taken great care of it and at some point in the past, filled the radiator with water and not antifreeze. .. This past winter a freeze plug popped and I assumed it was just the plug. They replaced it but when they...

My B7500 tractor has an LA302 loader and takes a 48" bucket. I would like to replace the bucket. I found a new one, 54", for a reasonable price that fits on an LA403 loader on a B2630, B3000, or B3030. Does anyone know if the pin size is the same and if the brackets are the same width, etc...

I am looking for some high/low pricing in southern New England on a hydro kubota B7500 with Woods backhoe, loader, tooth bar/bucket hook, tire chains, and 3 pt. auger with three different size bits, and 3 pt hitch set up, 780 hours. I would appreciate any input anyone has. Thanks. Teach

I am looking for some high/low pricing in southern New England on a hydro Kubota B7500 with Woods backhoe, loader, tooth bar/bucket hook, tire chains, and 3 pt. auger with three different size bits, and 3 pt hitch set up, 780 hours. I would appreciate any input anyone has. Thanks. Teach

Good morning everyone! I've been referring to this website for a long time, but I've got a question that I can't find an answer to so I signed up. My 2004 Kubota B7500 (no FEL) travels faster in reverse than forward on level ground. I've checked the linkages and the limiting screws are not the...

I am the original owner of my B7500 HST with RCK60-24B mower deck. I have recently been having some issues with what I'm not sure. My yard is flat in front and sloped (considerably) on the sides with the house having a walkout basement. Here are the symptoms, and it seems to get worse as...

Not sure of the year. Has belly mower and loader. They were made between 2000 and 2003 according to various Google sources but they don't give the oroginal MSRP. I bought it for $8K a couple of years ago.

bent a wheel this evening. 23 x 8.5 x 12 industrial tire? anyone know a part number I can go with.

I think I need to replace the rear bearings and seals on the rear axles of my B7500. Is this a difficult job or do I need to take this to the dealer to have done? I know if I go to the dealer I am sure this will be an expensive repair Would I need special tools or will my normal sockets and...

Bought a 03 b7500.....has a 60 inch mower already to bushed rds and small plots....looking for a small disc for little food plots. Thoughts? Thanks

Been searching for a while for a tractor - had an L2800 which was great for a lot of the things I need a tractor for, but not for lawn mowing. Had a lawn mower for that, but now I have neither so looking for something in between. I've been over the B/BX dilemma, and think B is better for my...

So... I need a rear rim. Any advice on prices, aftermarkets, etc? Tire says 12x65 for the size. Thanks

Hi Gang, Trying to get info on purchasing a good backhoe for my Kubota B7500 tractor. Wondering on the mounting of the backhoe, which would be the best system. Mounting to the 3 pt or the under carriage mounting system? Also, what brands do I have to choose from that would be best for my...

I am looking for info, Kubota is ZERO help. I have 21x8.00x10 Firestone Turf & Field on the front. One blew... One tire is $140 then the shipping... then the mounting, so it's nearly $200 for one tire. Kubota says the replacement is a 12" tire... okay, I'd have to have a pair, that's nearly...

My cylinders are leaking on my LA302 loader. Where can I get the rebuild kits for them? I cannot find anything online. Thanks.

Hey everyone I'm fairly new to tractors, and very new to Kubotas so I'm hoping the experienced members of this forum can help me out. I'm in the market for a sub compact tractor with an FEL and eventually a backhoe. I have a quote from my local Mahindra dealer for an eMax 22 with FEL for...

looking at a 2003 b7500 HST 4x4 with power steering and front end loader. Owned by an old man just in on trade. Still in the back. 570 hours. 1/2 tread all the way around r4 tires. Going to throw in brand new woods back blade. Got them talked to $7600. Does that seem reasonable? Thank you

I am considering purchasing an Earth and Turf plow model 1sc600 for a Kubota. Does anyone own one and what is your experience with it? It clamps on to the bucket. Thanks, Debra

I need a front tire (or tires). 21x8.00x10 Turf and Field ... Kubota discontinued the part number.... BS!! Firestone discontinued tire, a company bought a bunch and are gouging people on Ebay at $152 a tire!! BS again! So, I need a replacement or what's size can I use on my 4 wheel drive...

I am new here and had some questions about getting a front mount snow blower for my B7500 with a Woods backhoe and Woods sub-frame. I've talked to the local Kubota dealer and will most likely get the newer BX5450 that replaces the older 2750 blower. No one at the dealer can answer my question...

Figured a canopy would be nice on my little kubota, So after about 4 hrs I have this

After seeing how handy a grapple for my FEL would be I made one with stuff I had around the garage, I had to buy hoses and Pins but most else was already here, Also Made a removable lower tooth bar which helps to get under stuff,I made it light weight and did some rough testing today, Nothing is...

My main shift arm broke in half and I replaced it- but when reassembled, cannot get the shifter into reverse. I pushed the two gears that I can see - toward the rear of the casing before dropping the top back on. Is that correct, should I be turning the rear axle to re-align, etc. rear What is...

Hi new to the small tractor market. I have a Kubota b7500 2000 year. With 2200 hrs.seems to run ok .not sure I like the joystick controls yet.seems fairly gut less and from what I hear from a lot of folks they dont seem to have a lot of problems with thatarea.I had a load of black dirt brought...

I replaced a broken main shift arm and put top section back on (part with 4 bolts), but gears are not working properly. Shifter only moves to a couple of positions and seems to be in some gear, but acts like locked in gear with the brake on. Anyone have pics of the position of the shift forks...

I just got a Kubota B7500 with a FEL and I am building a grapple for the bucket for light brush cleanup, can someone show me where the Power beyond port is on the loader valve? Is it the #6 hose that comes into the right side if your looking at it or the other one on the other side? and I cant...

This is a unit I am looking at at the moment. I am just trying to find out if the combination works. The BH6000 is already on the B7500, I just wonder if anyone has any experience with a similar combo on capabilities. I posted in a general attachment forum also, but am pretty new here and may...

I have been looking for a TLB for about 4 months now. I have also looked into new, but would rather spend a little less and go used. I own 4 acres and my dad has 5 that I will being using the tractor on. With the low acreage I am maintaining and I dont want anything very big and less...

I need to change to change the fuel filter on my Kubota B7500 which will require that the fuel line be purged, but I don't know how that is done. The engine began bogging down while cutting grass (60" cutting deck). When I disengage the deck, the engine pick up. When I engage it again, the...

I started my B7500 this morning, drove it about 50' and it died as if it had run out of fuel. I tried to restart it but it would not even try to fire. The B7500 doesn't have the electrical interlocks so all it needs is fuel and air to run. :mad: I checked the obvious stuff first. It had about...

Hello: I have a 2003 b7500 with 250 hours and noticed oil on my garage floor the other night. I pulled the right front tire off and can trace the leak between the studded hub and where it goes into the axle. Outer oil seal? How easy is this to replace? Do I have to remove the 8 or so bolts...

I've got a 2000 Kubota B7500 that I've had since new. This tough little tractor has never given me any problems on my vineyard. I have a couple of acres of grapes and use it for mowing, tilling and spraying. I pulled it out of the barn a couple of weeks ago and did some mowing and then put it...

new member, from georgia-but trying to teach texas how to do things right

Some one local is selling a TnT gearmore kit rams hoses 2 spool valve for $500 Only concerned it wont be enough for the 7800 senice it was for b 7500 should I buy it anyways?

Hey everybody, Our B7500 is locking up going down the road....Seems like maybe front axle is locking up, although not sure yet...anyway we are trying to get the front driveshaft out...so what is the secret? We want to disconnect it from the transfer case/ front pumpkin and try it to determine if...

There was a plastic insert screen at the filler on my tractor and it's not there any longer. My hunch is the nozzle of the fuel can punched it into the tank when I was refilling. I noticed the fuel gauge doesn't drop any farther than 1/2 tank so I'm thinking the insert is interfering with the...

I own a Kubota B7300 with MMM, and B2400 with MMM and FEL. The B2400 3 pt hitch has position control. Now, considering a B7500 purchase with MMM and FEL, but does this Kubota have position control? Also, what is the Kubota model FEL for a B7500? I know B7510 has position control, not sure of...

I have a 2003 Kubota B7500 (650 hrs) 60 MMM, LA402 FEL, Rotary Tiller, 4Ft Brush hog, 5Ft Woods Box Blade and was thinking of trading all of that for a new Kubota Zero Degree Mower. I mow approx 4 Acres+ or should I say my wife does. She loves the little tractor for mowing but I think it...

I have a 2003 Kubota B7500 (650 hrs) 60 MMM, FEL, Rotary Tiller, 4Ft Brush hog, 5Ft Box Blade and was thinking of trading all of that for a new Kubota Zero Degree Mower. I mow approx 4 Acres or should I say my wife does. She loves the little tractor for mowing but I think it would be a much...

I have to replace some oil seals in the front axel of my b7500 . I am having trouble removing the first snap ring . I have researched the forums and everyone says you needs a good large pair of snap ring pliers , but no one list a brand or model number . Just checking to see if any one has any...

I just bought a used "like new" B7500 from a family friend and want to put a mid mount mower on it. I found a "new in the crate" RCK60B-75B deck but Kubota lists that deck for the B7510 tractor only. I contacted Kubota and you guessed it...they cant tell me anything other than its not listed as...

Hey Guys, I'm ready to buy a machine with a backhoe on it. I've ran an ad, and had two great responses, so now I need to decide which one to get. Your thoughts and input would be greatly appreciated. The one thing I do *need* to do is rehabilitate a few septic systems (not new installs, but...

Hello, I was wondering if anyone has a PDF version of the Service Manual for a B7500HSD Kubota. I have a low pressure leak in one of my hydraulic return lines and I'm hoping to find out exactly what part to order, but the illustrated part diagrams on the Kubota site is too vague...

Hi Guys. I'm think about picking up a B7500hst with around 700 hours on it. The tractor comes with a 60"mmm, 4x4 w/R4's, and the 302 FEL. I haven't looked at it yet, but the pics make the machine look in very nice shape. Straight bucket, original owner. Asking price is 11,500. (seems kinda...

Can anyone point me to a LED plug-in replacement to the headlight bulbs that came with my 2003 Kubota B7500? The OEM headlight bulbs are 15 watt medium (intermediate) base, single contact, bayonet type incandescents, also known as BA15s. They are the same configuration as 1156 automotive...

Hey all...back in the market for a compact with FEL. The one I'm looking at is a B7500 HST with 600 hours. Good shape, FEL, box blade, canopy and 60" MMM (not currently on the tractor but looks like its in very good condition). Asking $8500. Good price? Thanks.

I have a B7500 and love this little tractor to death. Just helped my neighbor till his garden using my KingKutter. Awesome tiller. I have been here a little while. My question of the day is, Why don't I see a lot of post regarding this model? Was is it not popular or is it just a simple tractor...

I've been looking around for a compact tractor to use on my 20 acre iowa farm. Basic stuff - cleaning up the horse pasture, loading the manure spreader, pulling a mower at least around the pond where my riding lawn mower gets stuck but maybe taking over more of the mowing, moving some dirt /...

I picked up a B7500 with a collection system but I dont have books or find a Model number It looks complete but I cant figure out how it mounts, There are no extra brackets on the tractor and their is only a square bracket coming off of the frame work with 2 horizontal holes. Im guessing there...

Somehow the 3 pt lift quit... The lever ain't a working as it should... seems like something came off... I didn't mess with it much but it just ain't right at all.... I hope to figure it out come Saturday. Is there a page/picture of what the lever/linkage looks like to see if I find find...

n 2001 we bought the B7500 with a FEL to help me finish digging a basement under my Dallas home. I hauled around 300 yards of black clay and chalk rock out of the hole and then carried crushed rock for drainage back down in there. I had dig a ramp outside in the back yard to gain access under...

Hi All, Can someone please point me in the direction of a pdf for the Operator's Manual for a B7500? I have the service manual, but there are some things that it doesn't cover (e.g. ROPS), that I'm assuming the Operator's Manual does. Didn't see it on Kubota's website and Amazon wants...

My tractor was running fine. Then while trying to start if following day it would not start. The tractor was dead. The lights and all other electrical items were working and the battery was charged OK. I had the kill button all the way in as required and clutch was in (it is HSD). Turning the...

I have a 2002 Kubota B7500 HST with loader and blade... It has less than 200 hrs on it. It has been keep in shop during winters. Looks and runs like new. I'm looking for information on what it is worth. Thank you for your assistance...

I have owned my B7500 for just over a year now. It has about 630 hours on it. This spring I started noticing a whinning type noise coming from the front right tire area. Mostly in 4 wheel drive but does it to a lesser extent in 2 wheel. Takes a little time of use before it starts and can be...

B7500 runs well for a hour brush hogging, The. Loses 500-1000 rpms and blows white stinking smoke. I have changed fuel filter and added a bottle of Sea Foam but I don't see any difference.

The other day I noticed both my rear wheels (loaded) were lose( 1/2 inch movment side to side). The nut on the bolt which connects the hub to the axle were both lose. I thighten both up but but after cutting the grass several times they were slightly lose. Are the hubs shot? Or the cotter...

G'day All, I just want to say a quick thanks to everyone who has left feedback or answered posts about the B7500. I have been deciding whether to buy one at my local ag shop. Things were further complicated by me finding a BX1800. Both are equipped with MMM and FEL. Similar prices (listed at...

My neighbor just picked up a used 2002 B700 and wonder what the circled symbol means on his switch in the pic. It will not move to that position and wonder if it is only used with an option? Also not sure if the center portion which is a button is supposed to do anything?

I have a Kubota B7500 with bucket and RCK 60 24B mowing deck with around 660 hours. I lubricate the deck every other time I mow. In the past on really hot days while mowing my 4.5acres of grass it might overheat. When it did, i would stop, clean the filter and grille and the temperature gauge...

Looking for a shop Manuel online to view

Not sure the model number but I have a chance to buy a 5' bush hog. PTO will match up but will this be ok size for my B7500 tractor? Also, check out the photo, how much do you think it is worth?

I've searched the forums, I've done some homework, now I'm looking for some more opinions on a specific setup. I'm looking to mow some steep embankments with a B7500 and a sickle mower. It seems to me that a belt drive is the only way for me to go since I want to mow below vertical. I also...

I have two acres uphill, including a 30 degree pond levee. I've mowed the levee with a B3200 going straight up and down and an L3400. It's not a problem in 4WD. I just didn't want to spend big bucks. Was gonna buy a Garden Tractor from Sears and try it. A friend has a B7500 with 300 hours that...

I will be trading my b7500 for a bx2360 soon & want to know what I should expect? Lack of power? Traction? The b7500 is a gear tractor with AG tires & goes anywhere, has a loader. The bx2360 has industrial tires, loader & belly mower. I guess I am just nervous about getting rid of B7500, been...

Can anyone tell me if the belly mower deck that came with the b2100 (kubota deck) will fit the b7500? They look to be the same specs, guessing the 2100 came before the 7500. Thanks!!!

I really trust your advice and have relied on it for some time now. Just purchased a B7500 w/ a 60" MMM and 700 hrs. The tractor seems to be in good shape and I'm prepping it for service this spring. After a full fluids change and service I think it'll be ready to go. My question is this: The...

Questions on a Kubota B7500 TLB Currently looking to buy my first tractor. Looking at a B7500 TLB. When I referred to the dimensions, it seemed to be a bit short and narrow? Hoping I can get some feedback on this model. Is this a well built, capable, reliable tractor? Have 4 flat/sometimes...

Hello. I just purchased a 2000 Kubota B7500 HST. Need to change fluids immediately, assuming that previous owner did not. Oil: What Rotella brand is recommended? Any other recommendations on things to replacem add, etc.? Thanks, Griller65

Newbe here, just got a used Kubota B7500 hsd and was thinking about some remotes but looking through the manual appears that the pump only generates 4.4gpm...? Am I reading that right? Was thinking about wood splitter, TNT, backhoe, etc Thanks!

Ok, my bad, just 3 months after buying a used B7500, I have lost the key! After hauling my gun kill deer back to the garage, I must of put the key in my hunting coat and gone back into the woods and it fell out some where. So.... how does one go about getting a new key?:confused:

I was shifting my kubota from reverse to 1st and after stopping and pushing in the clutch i moved the lever into 1st gear. Now my shifter feels like there is some sore of linkage broken. It is stuck in neutral and the shifter just flops around. Already removed the seat and brackets to check...

I'm considering buying a 2002 Kubota B7500 with 302 FEL, MMM, hydro trans, and Curtis cab with heater. It has 138 hours and turf tires. A private owner has it for sale and will take $10.1K. It also includes a 5' back blade. Any opinions on this tractor and deal? Thanks.

Now that I have my Kubota B7500, I seem to have a intermitant starting problem. Mostly on cold starts, nothing happens after warming the glow plug, pushing in the stop button and turning the key. I may have to go thru this for several minutes till it will fire and then turns right over. The...

My rear PTO worked at one time, but I don't normally use it. Only the mid-PTO for mowing. I had a leak at the rear PTO shaft seal for a while and finally got around to replacing the seal. When I had it back together and checked everything, only the mid-pto works. Since I wasn't sure if it worked...

Hello, Curious to get your opinion on the price of this tractor I'm considering a 2000 Kubota B7500HSD, has aprox 1100hrs, LA272 loader, 60" mid mnt mower, Back blade, box grader. I'm told in good shape, pictures look clean, loader looks very used. The ROPS is solid not foldable. Price is...

My B7500 Hydrostatic drive tractor runs fine, but when you travel at a higher speed, I get the screaching sound. The sound is not there at slower speeds.

Hi there, I have been out of the country for 6 months and when I started my Kubota B7500 for the first time it started immediately however the cutting deck will not engage. I only purchased it just before I left and have never used it to cut, although I am sure it was working when I...

looking at a 1997 Kubota B7500 with loader in good shape. What kind of price is fair for this machine?

B7500hsd diff lock problem Hi, 1st post and need help. My diff lock peddel will not return up normally. I tore diff axle assembly apart and what is happening is the pin on the shaft is falling down when the peddle is depressed all the way preventing it from rotating back up. The dog clutch looks...

Hi, 1st post and need help. My diff lock peddel will not return up normally. I tore diff axle assembly apart and what is happening is the pin on the shaft is falling down when the peddle is depressed all the way preventing it from rotating back up. The dog clutch looks fine and I see some wear...

Hey all I am looking at buy a 2001 B7500 kubota with just over 500 hours. The owner has a york rake and a rear blade attachment that is going witht the tractor. Also has some sort of 3 point hitch for standard ball, trailor hook up. Oh and a Fel! He is asking $7000.00. I want to use at my...

A friend has a belly mower from his B7500 he wants to sell to free up some space in the garage - looks like 60". It's in nice shape because he has a RFM he uses instead. What do these sell for? What other tractors would it fit?

I've searched these forums and even RTFM, but I need voices of experience. This is a tractor question combined with an attachment question. I'm new to tractor ownership and just finished my first season mowing our 15 acre place in the northern California coastal hills with a used Kubota B7500...

I've got a B7500 with around 300 hours on it. The engine sounds fine at rest and its always worked fine up until now. But when I drive it, now it makes a sort of grinding noise that sounds like its coming from either roughly the midsection or more towards the front. I'm pretty sure the sounds...

Have been looking for a tractor for too long & missed a good Kubota on CL two weeks ago. Missed this one by about two hours, a good deal that actually hurt as I thought I was finally 'done' & was looking at trailers & had gotten cost of getting Ags for it. It sold the next AM before I got up...

While working the ol' B7500 there was an awful WHINE from under the hood, then I smelt something that was like burned rubber, and then noticed my battery light on.... I believe my altenator just died .... Sound correct? If it died what are the altenators going for these days in both standard...

I need a rotary cutter (bush hog) for my Kubota B7500. Is this tractor capable of handling a 60 cutter or should I buy a 48 deck? Thank you folks have a nice day Santurinos.

Hi folks, Today I was using my B7500 which was working fine. Turned it off. Came back 2 minutes later and it will not even turn over. When I turn the key one light comes on the dash and that's it. I pulled the battery and had it checked and charged and its fine. Tomorrow I'm cleaning all...

I am looking at a land pride rtr1250 which is a new 50 inch reverse tiller for $2050.00 with the option to finance for 2 years at 0% or a woods gtc52 which is a 52" forward tiller for $1800.00 cash . I would be using this on my B7500 for gardening . My soil has a lot off clay that i am slowly...

I bought a used 4520B BH attachment for $2500. I know I can attach it to my B7500 via 3PH, but I go back to the sub-frame debate. My 7500 has a 60" mmm. I will be the only operator, and I am very nice to my tractor. The BH will be used for trenching and digging around stumps near Lubbock...

So, the alternator in my B7500 appears to have locked up. Schreeching belt followed by alternator light. Quick look under the hood revealed that what appears to be the pulley not turning. Just the belt slipping on it. Or I think it is. Never seen a critter like this before. It looks like this...

Does anyone know the spec.'s of a LA272 loader? Basicly it's lifting limit also a LA302 loader. I'm looking at two different B7500's with different loaders. Thanks in advance.

While moving snow from the latest storm my Kubota B7500 manual Transmission will not engage. The linkage is all attached and is attached to the rod that goes through the case. There is about 1 inch of play from left to right in each of the gears. Any suggestions?

All, I am thinking of selling my Kubota B7500HST with 185hrs. Includes LA302 loader, 60" MMM, 5 ft blade and rear tire chains. Tractor is in excellent condition and has been garage kept. Can anyone help me with a value? Thanks in advance, Mike

My rear PTO worked at one time, but I don't normally use it. Only the mid-PTO for mowing. I had a leak at the rear PTO shaft seal for a while and finally got around to replacing the seal. When I had it back together and checked everything, only the mid-pto works. The PTO shifter moves smoothly...

I have 2 prices on a 5 foot and 6 foot rear blade ( woods ) the 6 footer is $125.00 more then the 5 . Which one would be better suited for light snow removal and light grading Thanks

Drove over to my fathers today to mow down his garden . He is about a mile away from my house . Tractor drove over fine , but after about 10 minutes of mowing down his garden my RPM' s started to drop a little ( RPM was at 2600 in low gear ) I didn't think much of it because I was mowing down...

i am looking at backhoes for my b7500 hsd need help deciding on which one to choose kubota bh65 or woods bh70x both with sub frames.any help would be appreciated

Hi Folks, I'm a newbie & I'm not sure if I'm in the right section; please let me know. Anyhow, I'm looking for a complete front end loader including the arms, hoses, controls & a 4' bucket for my Kubota B7500 HSD. I don't care how it looks just as long as it is in good working condition...

hello recently purchased a massey 2310 with backhoe and loader on it.was wondering if the massey backhoe would fit on the kubota b 7500.if anyone has tried it and what sub frame i would need.

I'm looking at a used B7500 at the local dealer. It has a MMM, turf tires, 1065hrs, 2001 year model. It was a one owner tractor owned by an older gentleman who just traded it for a new BX. The salesman said they had sold him the tractor originally, and he did his own maintenance, so they didn't...

I (well actually the Kubota) just finished moving and stacking 115, 11' pine logs. I don't know what I would have done with out it. Some of the largest ones were a struggle and were only able to be raised by curling. A few times it took all 21 of the B7500's HP, but it was able to do everything...

I bought my Kubota b7500 7 yrs ago. I use it for mowing only. it has 450 hours on it. The clutch came apart at 200 hours, my local dealer fixed it at no cost to me. they said they had not had any problems with that before. after 150 hours it come apart again. its out of warrenty , but they fix...

clutch has went out for the 3rd time, with only 450 hours on tractor.

I have a Hydrostatic drive tractor. Never any problems until this year (6yrs.ok) When it is hot outside, around 100 deg., and I am mowing at 540pto w/2500 rpm's the steering starts to have a little bit of hesitation or scratchiness in when turning. The engine does not run hot, but obviously the...

Could someone please help me locate this? My friend's tractor but he always has service done. Working a long way from such now so need to check in the field. I think he got a bad batch of diesel.

Just replaced my seat with one of the $100.00 deals from Messick's . Wow what a huge improvement it looks just like the seats on the new B series tractors . The old seat wasn't too bad but it had a couple of rips and for the $100.00 it is a big upgrade . Thanks Messick's for super fast...

B7500 Delivered this morning . Thanks for everyone's help in my decision making process . A big thanks to Brady Barlow who was a big help even though i did not end up buying his tractor . Stand Up Guy ! . I ended up with a 2001 B7500 with FEL and a 54" mower deck 450 hours . The dealer i bought...

I have a 2002 Kubota B7500 need assistance in repairing positive traction

I have a 2002 Kubota B7500, I need assistance in repairing positive traction.

Has anyone had to repair or replace the drag link on a B7500? Mine has stripped the castle nut off and I'm wondering if there is an aftermarket or suitable repair/replacement for just the end. Any suggestions would be welcome. Love my Bota but this is the only weak spot i've found in 8 years

Hi new to this but I need somewhere to buy ends for the drag link on my kubota b7500. I cant believe some one doesnt make an after market end for them as the origanal ones arent all that sturdy and no way to grease them. And kubota only sells the entire link. has anyone else found just the ends...

my tractor search continues . thanks for everyone's help so far . i am still searching for the right combination of what i can afford and what type of tractor will meet my needs . so today i am going to look at a used B7500 with a FEL/mower . i believe it has 500 or so hours and is a trade in...

After 12 hours in the truck and almost 650 miles (with a 2 year old), my bota is home! Hope to get some seat time tomorrow.

Hi All, Just trying to get a little perspective on this setup that is being sold by a private individual. Its a 2003 B7500 TLB and MMM with about 350 hours. Everything is Kubota and he's asking $12,000. Sound like a good deal assuming there are no major outstanding repair issues? The...

A fellow is selling his B7500 with Kubota backhoe. The hoe is not a subframe mounted model but uses the 3ph (I believe its the 4672) and I'm wondering if this will cause problems down the road. I've searched the older posts on TBN and it seems that a subframe would have been preferable. Also...

I need some advice. Do you guys think a B7500 (21 hsp, hydro, w/ loader) is enough to run a 60" Landpride 3 pt. finish mower? I would mostly be mowing some fields and an old orchard that I have reclaimed after mowing for several years with a brushhog. I might also try mowing my own home lawn...

hello wanting to find out which hoe would be best on my b7500 hsd the woods b70x or the b60x.any help would be appreciated

There are two filters on the housing below the seat, one on the left side and one on the right. At first glance, they appear to be identical and located in symmetrical locations. What do these filter (hydro?)? Thanks.

Anyone know the top MPH with turf tires? Thanks

Has anyone used the BXPANDED Quick-On bucket hooks on a B7500 or other B-Series tractor bucket? I sure would like to add two grab hooks and one slip hook to my bucket. Harry at BXPanded has told me that looking into the B buckets is on their list of things-to-do, but obviously they have been...

Do not force the PTO shifting between the front and rear PTO. Sometimes it is difficult to get the front PTO in gear. Forcing it may break the shifting fork. Costly repair.

Was in a bit of a hurry in late Dec (09) to get in on KCC's 0%/60 months (yeah, I know, it's been brought back in March, oh well..), so I traded my 2001 B7500 (Woods FEL, 54" Kubota MMM, 425Hrs) to the dealer. I normally sell my tractors outright, but it was the dead of winter & I wasn't sure...

I have a B7500 that has ag tires. I would like to put the industrial tires on it. The rear is a 9.5-16 not sure on the front. Where can I find these tires?:)

A Kubota dealer is ready to sell me a new Woods PHD35 w/ 12" x 42" augar for $400 which seems to me to be a steal. My concern is that the B7500 21 HP engine provides only 17 HP at the PTO and the Woods PHD35 is said to be for 20-35 HP tractors. The dealer tells me that the Woods HP figures alway...

I am looking at a Kubota B7500 with brush hog for 4500.00. It is an individual selling it so no dealer warranty or anything fall back. I was only looking at spending 4K but this seems liek a pretty good deal. I am living in OK and have 5+ acres that need to be mowed but I am sure I could find...

I've found a used cab for a b21 tractor, since a b7500 is similar in size anyone got and idea if it would fit without major rebuild?

I have a Kubota B7500 with a front mounted snow blower. I shifted the PTO lever forward. It was hard to shift and there was a grinding noise. When I left the clutch out, the front PTO would not turn. Now the lever shifts back and fourth without depressing the clutch and the rear PTO turns a 540...

I have a B7500 that gets occasional weekend use. Anyway, for the last 6 months or so the tractor would run for a while, then lose power for 10-15 seconds before regaining power for a while, before losing power again. Though a nuisance, this problem was generally manageable and the tractor never...

Has anyone added a grapple to a LA272 FEL on a B7500 ? If so I'd sure like to know the specifics: grapple source, hydraulic control, etc. And for a general question: can I just put a couple electrically controlled hydraulic switches (diverters ?) on the curl up and down lines and divert their...

To try and make a long story short, I've been shopping for a used 20-25HP Kubota (preferably with a backhoe) for about 2 months now. I know someone with a Woods BH6500 for sale that came off a B7610. He's sure that the sub-frame will also fit a B7510, but he doesn't know if it will fit a B7500...

I've done some searching in the forum, but haven't found anything very conclusive. I'd like to get a 5' box blade to cover the wheeltracks of my B7500, but want to be sure that's not more box blade than it can reasonably handle. The B7500 has 21 HP, and can lift 615 lbs at the lift points (480...

What is the life of one? How long do they last before major issues start happening? What would be the equivalent of 100k on a car?

(Temporarily blocked due to reports of company closure) suggests the Leinbach L7200 Jr for compact and subcompact tractors. The "Jr" has a narrower U-frame (24" instead of 26") and shorter boom - which I believe will give me less ground clearance from the auger during transport. I'm leaning toward the L7200 but want to be...

i just bought a used rear blade for my tractor yesterday and wanted to move it after i pulled it from the bed of my truck. when i backed up to it i then realized i didn't have a top link. don't know how i missed it, but i did. so off to tractor supply to get a stage 1 top link and pins. 30 bucks...

I have purchased a used 2002 b7500 with 180hrs on it I don't really believe the 180 hrs but it was in good condition. I have since added a rc60-24b midmount mower and have noticed that when running the mower at speed (2500 rpm) and pushing in the clutch it seams to make a load ratcheting sound...

Hi everyone. This is my first post. i've been lurking on these forums for quite a while as i searched out my first compact tractor. i was just about sold on buying a mahindra when what seemed to me as a good deal on a kubota came along. funny thing is it's even at a mahindra dealer. i have...

Hi All The fuel guage is stuck on F on my B7500. Anyone know what might be causing that. Does it mean the sender in the tank is bad? Thanks.

I spoke to the dealer about mounting my 3pt boackhoe and my b7500, he said I should get the heavy duty top link mount and the b4681 frame support kit, but he was unable to tell me what the b4681 kit was or where it mounted or what it reinforced? I can't find any pictures of it or where it goes...

Hi All I'm looking for a Worshop Manual (WSM) for a B7500 part # Kubota 97897-12491. Does anyone know where there might be one available to view online. If not any ideas where I can purchase one for less than the $64 + shipping available at dealers? Thanks.

I recently purchased a used b7500 hsd, it has the r4 tires on it. I notice that it tears the lawn up turning, I'm thinking the tie rod is bent? i'll take some pictures tomorrow but the rod has a definite bend in the middle of the tie rod of about 3/4" would this be enough to cause toe in and...

I'm looking for a mower deck for a b7500 with a la302 loader, I understand the deck is an rck 60-24b. the deck came off a b2400. My question, is all the mounting hardware the same between the b2400 and b7500? I would like to find out before I buy a deck and the hardware only to find the lift...

I've been thinking about getting rear remotes for a 3pt log splitter. What do I need? Costs... I have a FEL if that'll help.

Can you use a Lienback 7300 on a Kubota B7500? I found a pretty good deal.... If the CEO agrees.

Hi Just bought a used Kubota B7500 tractor and I want to add the valve to run a front blade. Is the factory valve kit still avalible and where did it mount without loader. If anyone has a picture that would be great. Thanks

The blet on my mowing deck flops back and forth when engaged and it rubs against the other part of the belt that goes around the idler pulley.I thought it might be the tension spring maybe.Any ideas?The spring seems tight but I know it takes alot of pressure to hold the belt in place too.It's a...

233 hours - started right up - ran 30 seconds, coughed, spit out white smoke, now won't start. Turns over and emits very small amount of whitish smoke. Fuel filter or something worse?

What oil filters work on a B7500? No NAPA in town, no Kubota dealer in town, but have Advance, Auto Zone and K-Mart that are all open Sunday (time to do an oil change and figure tomorrow as good a day as any). You know, there may just be a NAPA too.

I'm brand new to the tractor world, and would be grateful for any advice. I'm about to purchase a tractor, and have narrowed my choices down pretty much to a Kubota B7500 and a John Deere 855. The Kubota is a 2002 4WD with about 300 hours on it. I belive it to be geared, not hydrostat. The...