Search results

Can anyone identify what make and model this lawn tractor is? It has a 17 hp Vanguard engine, a 42 " deck, and is labeled as a Limited Edition. There is no ID plate or sticker on it. At first glance I thought it might be a Craftsman built by MTD. Any help would be appreciated.

Can anyone tell me what type of electrical connector is illustrated in the picture? This is under the dash (behind the right side lower console panel) on my XG3037 and is not connected to anything. Thanks.

Am building a 10' x 15' loafing shed in my new paddock. It will be a three sided (front will be open) structure, 6' high in back, 8' high in front, wainscotting on the lower 33", and metal siding the remainder and roof. Rear posts are 4" x 4"and front posts are 4" x 6". Yesterday was Day One...

Well, I thought I had the starting issue solved, but it turned out that the clutch pedal safety switch was not the issue. It wouldn't start again and turns out it is the solenoid on the starter...had it bench tested to make sure. Has anyone else had any luck replacing just the solenoid on an LS...

The starter motor on my XG3037 started sounding funny the last several times I started my XG3037. Today after having turned it off while I did some other work, it wouldn't start. No click or any sound at all. Battery checked out fine at 12.9 volts, switch checked out fine, seat switch checked...

Just installed a set of RanchEx quick hitch adapter bushings on my 3 pt. rotary mower lift pins and what a difference! No more slop and won't have to worry about the mower lift pins jumping out of the Cat. 1 quick hitch arms. Highly recommend the adapter bushings for anyone using the HF or...

I am trying to find a replacement cap for my Speeco Model 65 PHD gearbox. The cap is the top part of the gearbox which has the flanges for the pin to attach to the boom. I busted one the flanges. The Speeco gearbox number is S52022000 but is also manufactured as an Omni PHD26 and several other...

Has anyone installed a Kats Lower Radiator Hose Heater on a XG3037? I think the one I need is the 16600 1.5" model, but am not 100% sure. It appears that there is limited space to install this, bases on it's dimensions, so was hoping someone has already done this and had some advice. Thanks.

Does anyone happen to use this filter on your LS tractor and, if so, does it have the sensor connector on the bottom? These are about 1/4th to 1/3rd the cost of the original and other brands.

I have a Bolens (MTD) lawn tractor, model 13AM762F765, and have replaced the pto cable, part 946-04173E, three times in one year. Cable breaks at same spot where it attaches to the pto engagement handle. Seems to be a very poor design. Anyone else having this issue? Is there a better...

Today I finished setting up my spot sprayer and the electrical for it on my carryall platform. Now I can spot spray the fence line and those small troublesome bramble areas. I had previously install a 12v power port on the left side of the dash console and will be using this to supply...

Found a small black rubber part, approx. 2" tall by 1.5" wide, on the trail that I drive my tractor on a lot. Figured it might be from my tractor, but darned I can figure it out. Thought I would post some pictures of it and see if anyone knows what it is and where it goes. What do you think it is?

Worked on my 3 pt carry-all project today. Started with a Countyline (TSC) 1000 # capacity carry-all, added a 60" w x 33" h backboard, and a 60" w x 48" d floor. Will add some hardware for straps, vertical pvc pipes for tools and such, and will paint LS blue when it gets warmer. Now I have a...

Have had numerous days of zero or below zero temperatures, snow, and freezing rain over the last 10 days and my Blue Mule (XG3037) has been a champ through it all. It has started easily every time and the 4W traction has been wonderful negotiating some steep inclines. I keep it in the barn when...

I am thinking about installing a 12v power port on my XG3037 and wondered if anyone else had done the same and where. I am thinking about installing it on the lower half of the console cover on the left side and would wire it directly to the battery with inline 15amp fuse protection. This would...

If I install a LS horn and switch on my XG3037, is a horn relay required? Thanks.

The OEM oil filter for my XG3037 is a 40283380 ($32.49) which cross references to a WIX 57000 ($20.86) which cross references to a Fram PH3614 ($4.19). My questions are....how can there be such price differences and is there really any advantage in using the much higher priced filters?

Does anyone have a recommendation for a SAE 80w-90 GL4 gear oil for the front axle of a XG3037? Just checking to see what others are using. Thanks.

I have been trying to figure out which coolant I need to for my XG3037. The manual says that I need at coolant that satisfies ASTM5216, but then I read somewhere that a ethylene glycol based coolant that meets ASTM 6210 would also satisfy ASTM5216. My local farm supply carries the Peak Fleet...

Anyone have a recommendation on what I should use to weatherproof the wood deck of my new trailer? I would like to get as much life out of it as I can. Thanks.

Does anyone happen to know the size of the zerks used on the LL3109 FEL? I busted one while greasing and need to replace it. The owner's manual does not list this part. Thanks.

The 3109 FEL on my XG3037 is raising very, very slowly and the bucket seems to develop some slack or play when left in position after a few minutes. The FEL also seems to be straining to reach maximum height. This all started suddenly today for no apparent reason. Tractor has 160 hrs and was...

I have an XG3037, 160 hrs, and just noticed that the steering wheel can continue to rotate even when the front wheels have reached the limit of their turn. Is this normal? Thanks.

Most of the parts for my LS are also available through my local New Holland dealer. Only difference is the NH part number has the MT prefix. I knew that LS manufactures a great portion of the NH line of tractors, but was curious about parts so I did a little research. I will always try to...

Any opinions on Shell Rotella T5 10w-30 synthetic? Am considering it for my XG3037. Thanks.

I purchased a Cat 1 Quick Hitch from my local HF for my XG3037 and have to say that it has been one of the best tractor "extras" that I have bought......ever! No more killing my back or having to wait until I have help. Works great and is quick and easy. Did have to buy a couple of adapters...

In the span of one week, I have had to replace the head gaskets on both of my lawn tractors. One is a Troy-Bilt and the other is a Craftsman. Both have B&S single piston OHV Intek engines; TB has a 17.5hp and the Craftsman has a 20.0hp. The repair is fairly straightforward (there are also some...

After numerous unsuccessful attempts to round up our ducks at the end of the day (they preferred staying on the pond at night), my wife and I decided to provide them some shelter on the water using a repurposed small chicken coop. Here is a picture of our floating duck house....the SS Moby Duck...

I hooked up my new Speeco 65 post hole digger to my LS XG3037 today, but not sure this is correct: As you can see, the bracket on the boom of the PHD (2" wide) will not fit inside the top link mounting bracket (inside clearance is 1.75") which forced me to offset it. Is this normal or am I...

I am quickly approaching the first service for my XG3037 and began researching and comparing prices for the necessary filters (oil filter, pre-fuel filter, fuel filter, outer air filter, inner air filter, and hydraulic filter) and was shocked to learn that there is a huge difference in prices...

I have an XG3037 and inherited a Ford 903 PHD that I decided to hook up to the tractor for some weekend work. It was a bear getting hooked up but finally got all three points hitched. Problem is that I cannot raise it high enough to get the auger bit off the ground. Is it possible that the auger...

I have a new Kodiak STD 60" 3-pt rotary mower and need to replace the shear bolt. Problem is.....I have never done this before, the manual does not cover this, and I can't for the life of me figure out how to get around all of the shields to get at it. Below is a picture of the gearbox and...

Took delivery of my new XG3037 a couple of weeks ago, but haven't had much time to play with it. Finally got some seat time today and started by adjusting the new mower (side to side, front to back), adding 2.4 oz of PS Diesel Kleenw/Cetane Boost to a full tank of fuel, and then mowing about 10...

My LS XG3037 was delivered today and I am thrilled with it. Ordered it with the LS 3109 FEL, Kodiak SD5 mower, dual rear hydraulic remotes, rear work light, R4 tires, and 110 gals of tire ballast. Ordered separately a Titan 42" Pallet Fork/Hay Spear. Already had a 3 point post hole auger so I...

I am considering the LS XG3037 with a LL3109 FEL for my small farm operation. Will primarily use it to lift/move 4x5 bales of hay (700-900 lbs max), mow approx. 30 acres 2-3 times a year, and then just general bucket work. It appears from all of the specs that the XG3037 should be able handle...

I am considering a NorTrac 35XT with a Koyker 160 front end loader for my small farm. Any input or thoughts would be greatly appreciated! Thanks.