leak

Would anyone know of an additive that can be added to the hydraulic oil in my New Holland 1530 Boomer compact tractor that lets you see where oil is leaking? Preferably something that can be seen with UV light. I have a slow leak; maybe more than one, but I can't tell where the source is. One...

Well, first major problem with my 2002 BX2200... My rear right hand axle seal is leaking. Got ~2,400 hours on the machine. It's a slow leak, but I got all the parts and it works out perfectly because it is due for a full service (less the lash adjustment). When buying the seal, I noticed that...

Hello. I am new to TractorByNet and wanted to get some advice. I just acquired a Kubota lawn and garden tractor GR2110 with 550hrs. The tractor is in good condition but the right side front axle case is leaking hydraulic oil. The oil starts to leak about (2) two days after the tractor was last...

My low hour (60 hours) MT342HC has started to leak hydraulic fluid around the cover where one would drain the hydraulic fluid from the bottom of the rear axle. It's not leaking from the drain hole nut but around the cover (6" x 7") that the drain nut is taped into. Its a small leak and a such a...

My 1968 5000, with early-style power steering developed a moderate leak from the cylinder back in early winter. When I got the tractor two years ago, the PS fluid was red in color, which led me to believe it was running on some flavor of ATF or power steering fluid. I do not know what variety it...

My HST tractor is consuming 3-4 quarts of hy-tran every few hours of doing loader work. The hy-tran is shared for the steering, hydraulics, and HST. The skid plate is off so nothing is pooling on top of it. First, the dye I used last fall to find two hydraulic leaks off of the pump has been...

The shaft for the 4 wheel drive is leaking fluid at the rear of the tractor. The shaft is loose and I can slow down the leak by pushing the shaft back and or rotating it. I am wondering if there is a seal that I can replace. I am trying to find a diagram with part numbers so I can repair this...

I have a gambrel(some call it a hip roof) "barn" with a shingle roof, a lean to with a standing rib metal roof that is attached. Never had any leaks until about a year ago I first had 5 inch D spoutings put on with similar downspouts running into underground pvc to carry the water away...

My old M7030 is ozzing oil around the left front wheel (over the winter is leaked a +/- 1/4 pint). I am presuming a seal has failed. I have a shop manual and it doesn't mention replacing a seal. Is this a DIY project or is it a major job? One thing I haven't figures out is the zerk grease...

Hey All, I recently came into possession of a MF-253 with about 4500hrs of use pulling attachments in an orchard. The rear right axle is leaking hydraulic fluid pretty bad - bad enough that it needs topping off every other week or so to keep things running smoothly. I have it all pulled apart...

My TC33d has hydraulic leaks at weep hole, it loses a lot of fluid. I saw a post where someone thought that o rings might be bad on tubes in the area, but no resolution. I wonder what could cause this. It does seem to be worse when using the loader. Has anyone fixed this?

I have a 2001 TN 70D with 1000hrs on it. Over the winter a mouse has chewed a hole in the small fuel return line that runs between the injectors. My eyesight is not good enough to determine how that small line is attached from fitting to fitting at each injector. Has anyone had to replace those...

I noticed some seepage on the underside of my TC33DA. Photo attached. The top left bolt shown in the photo was slightly loose, and I tightened it by about 1/8 of a turn. The other bolts (at least the ones that I can see and get to) are all tight. Tightening this bolt reduced, but did not...

One of my spools is leaking from the top. I found the thread about the o rings. Any new information? My question is..is it serviceable from the top by just taking the lever off and removing that plate ? And while we are here, how do you get the stabilizer levers off to replace the boots ...

Hey guys I have an oil leak underneath the cab. There it looks like it's coming from right under the floor somewhere but there is no clear sign where it's coming from What is the best way to lift the cab to to get a better look?

I have a 2010-2011 John Deere 4320 with a small leak on the front axle. It’s not down by the wheel, seems to be leaking where the front knuckle (not sure if that’s what it’s called) bolts to the axle with the 4 bolts. I talked to the tech at John Deere and he says there isn’t a gasket just rtv...

A friend has JD 5000 backhoe. It has a bad hydraulic leak around boot for lever (see picture) on top of case. Supposedly, leak started after swing cylinder hose was replaced. Thoughts?

Looking for any suggestions or help with my 2015 Mahindra emax 25 hst. I have a leak coming somewhere from the front of the transmission. It's hard to tell exactly where so I started to take the black plastic cover that's over the driveshaft but wasn't sure how to get the deck adjustment knob...

I have a land pride tiller for my kubota L3800 and have replaced the gasket on the side of it a couple of times but it still leaks oil and I don't really want to change it again because I know it will just contine to leak again. What sort of solutions are there to remedy this?

I am seeing hydraulic fluid dripping from bottom of Hst unit. It appears to be coming from the top of the hst unit someplace. Does any one know if there is a vent or breather on top

I have a 2005 BX23. For quite some time it has been leaving a little trail of hydraulic oil that drips off the bottom under the HST. I have searched to no avail; I finally found a mechanic who understands small Kubotas and he spent the time to find the problem. There's an opening on the top...

Hi The power steering controller at the base of the steering column on our 1996 NH 2120 is leaking too much so we put it in the garage and hope to be able to repair the leak . I’ve never done this before so any advice or suggestions are welcome. I looked at it and thought… I may get lucky...

I have a mid 2000s Kubota R520s that I bought used and is kind of a clunker. Since I’ve owned it, hydraulic fluid overflows out of the brake fluid reservoir while operating it after a short period of time. The LST oil pressure light stays on during operation and despite that, the tractor still...

My 445A, 4WD skip-loader is dripping from under the front, where from the Messick & New Holland diagrams show as a junction for L/R hoses to each hyd cylinder. The lines coming down from the power steering control valve(column) go through a rubber grommet. How do I access that junction? My Ford...

I have a leak on one line running from the fuel pump to the injector on my Massey GC2300 with a Iseki E3112 engine. The leak is where the line connects to the fuel pump. I have tried tightening the line nut but still leaks. I do not see a o-ring in this fitting. Does anyone know if there is...

Checking to see if anyone has come up with a different solution for replacing the hydraulic steel high pressure line that leaks under the seat, from the pump to the control valve.. Possibly with a hose. The fitting that I think would be an issue is the one at the pump with an O ring and 3...

Seasons greeting all. I posted my intial tie rod breakage inquiry in the General Repair forum, but realize now I should have posted here. To preface my current situation, here is a link to that post for some history...

A recently acquired 235 has a power steering leak at the pitman shaft seals on the gear box. I read,possibly on here, about multiple problems with the power steering but never found anyone saying the actual part number for the seals on the pitman shafts. 1876962M1 is the number,still...

Woods9000 on my L3710. There's a pinhole leak on one of the lines. Its one of the longest lines on the setup too. No idea how the pinhole got there, but its away from all mounting surfaces, bends, couplings, or anything. Right on the "straightaway" on the line. Easy access, right there. Is...

I have a coolant leak on my 1983 JD2150 which I haven't been able to detect where it's leaking. Everything in front of the radiator is wet, some damp, some dripping, but there's enough dust caked on things that I can't see the source of the leak. The tractor runs fine until a heavy PTO load is...

My John Deere 820 has a hydraulic leak on the valve under the right floor panel in front of the rear axle. Is this called a dump valve and can it be removed without draining all the hydraulic fluid to replace o-rings? It has a steady drip.

Well folks, had both FEL seals replaced in the spring. The right hand side was dripping. So I figured OK, get both done. Used a local guy in Victoria has his own hydraulic shop. Here we are maybe 40 hours later and today I see a wet booger forming on the fitting. Only thing I can think of is...

I've had a slow leak on the M59 since forever. One of the rear 17.5x24 Titan industrials needs airing up every two months. The tire shop where everyone gets tractor and heavy equipment tires recommended "the original Fix a Flat" for truck/SUV. It's a 24 fluid Oz pressurized can with a hose and...

My King Kutter brush hog is losing gear oil from the gear box. It's not coming out around the gear box on top of the deck. Any idea where it would be coming out?

This leak was found in the first three seconds of the engine running. The rear hardline has developed a crack in the weld Under a UV light to the naked eye this appears as a fusha green oil leak. Sadly, I'm not advanced enough to color-correct a camera for UV light but the rear hardline is...

This is a 1985 SAME (now SDF) 85HP Mercury 85. I had a lot of of leaking from the starter motor (???!!), it was from the bell housing, flying around in there. I assumed it had to be the rear main engine seal, but it turns out to be gear oil leaking through an end cap. There's an Oring in there...

I was trying to replace the PTO seal on my 2015 Mahindra 4540 and when I took the cover plate off and pulled the seal off, the shaft came right out of the rear of the tractor. I cleaned it and now I cannot re-install the shaft. Is there a secret or an alignment trick to getting the shaft back...

Looking for some help. I have a leak on the high pressure side of my pump. There is a flange with 4 bolts and an O ring on the pipe. The pipe goes back to the 3 point. I’ve tried a couple different O Rings based on matching them up at the auto parts store. Not working. Any ideas? Thanks

I have a 2017 Branson 3625 tractor , I believe its 3620 in US. Only 108 hr on it and the front hubs started to leak. I bought it last year with 46 hours on it and have used it for FEL work mainly. First owner bought it new but almost didnt use it because of health issues. I changed all oils and...

Hi all, my old John deere 2040s is leaking oil out the connection between the link arms and the diff housing. My local (400kms away) dealer was nice enough to sell me the seals but I'm buggered if I cam get em out. I can get the link arms off and the shaft to slide out either side but I can...

I have a hydraulic leak in one of the hard lines on the block to my rear remotes. See highlighted circle in pic. Someone has used jb weld on it in the past but its leaking again. I cant find a part number for the block or on a diagram. Can anyone help with a part number. Its an L3240DT...

Oil is leaking from the shaft and there is a lot of play in the lever/shaft. What parts do I need to replace?

Used a three point rotary cutter on the lane and ditches last night. Came in this morning to a huge hydraulic fluid leak on the floor. Apparently a stone or something flew out of chopper into the metal seal/plug just below the PTO output shaft. It broke the outside lip on seal and fluid is...

Well howdy. My Branson 2810 has a BL10 FEL. Has always worked well. I now have a rapidly dropping (leaking down) tilt on the FEL but cannot find any evidence of any external leaks. None from cylinders and none from any of the hydraulic lines. So, any suggestions on finding the leak? The...

2015 Tuff Torque K72 in a Deere X500 that began to leak transmission fluid; drips on cardboard after mowing. Not a lot; 1 ring the size of a silver dollar or so. After a few cleaning/mow/examine cycles it would appear source of leak is the input shaft seal. Don't know for sure, but its coming...

A friend has a L3301 with the hydrostatic transmission. The two lines with three connections shown in the attached pictures are leaking where the bolts hold them to the filter base/housing and the transmission housing. It looks like to me that the fix would be to replace the O-rings is that...

Can anyone tell me what this hole in the housing is there for? It’s dripping hydraulic fluid like a faucet that needs a new gasket or money going out the window like Bidenomics. 😵‍💫 6 volt VW Buses and dirt bikes I know a little about but tractors!!! Clueless.

I have a John Deere X758 and a seal is leaking where the drive shaft connects to the rear axle housing , I am trying to find the seal part number so I can order a replacement seal , I have looked in the John Deere parts section and I cannot see the seal listed in the parts diagram ,would anyone...

Hello, I was curious if anyone could help me find a repair manual or give me some instructions on how hard it is to fix a leak in my hydraulic system on my Kubota B7100 HST Diesel. The leak appears to be coming from the actual controls itself. I also noticed that there is a drip that looks like...

Pressure Control Valve blowing o ring on JD 310B what could cause this problem?

I have posted before about adding rear remotes using the Summit monoblock, primarily for top & tilt. Finally got around to it and finished it yesterday. Everything works as it should, but one small issue. When I first tested it, other than a few connections I had to tighten a bit more, there...

Have a new mt226 with 40 hours. Looking it over and i noticed the rear of the oil pan is seeping. Checked in the bell housing and its not the rear main. I checked a few pan bolts to see if they were loose and nope. Trying to decide if im going to leave it or send it in for warranty. Little...

I have a leak on the Nimco FEL control valve below the joystick. Is there a gasket attaching the silver box at the base of the joystick (to the black casing)? And is it easy to replace? Might it be an o-ring on one of the connectors that’s an issue? I see no leaks around the attached hydraulic...

I've developed a hydraulic pinhole leak on 7/8 OD tubing on my Ford 4500 TLB. So far, I've been unable to loosen the flare fittings to pull the piece out. Do they make a repair clamp that would work in the situation?

Good evening, I am battling a John Deere x485 exhaust leak this week. Kawasaki 2-cyl FD711D. Ive replaced both the metal gaskets, but I notice the exhaust pipe flange doesn't seat very flat to the motor exhaust port on either side. They appear to be slightly warped. Can I flatten the pipe...

Well just got this tractor one day ago only had 34 hrs on it.... ran it for about 4 hours, doing some loader work .. wake up this morning and both rear wheels right under rear axles have 2 small puddles, the fluid looks clear and oily either hydraulic oil or gear oil.. Didn't have to examine it...

Hi folks when I shut down the engine there's coolant dripping onto the floor; its not from the thermostat housing nor the overflow pipe...seems to be lower down and doesn't do it whilst the engine is running....any ideas welcomed.... I know that it could be expensive LOL

I have a hydraulic leak for many years. However it is getting worse. I looked it over for many times. I notice it after I use and park. I estimate it loses about 12- to 16 ounces, if you run it six hours. Being I only notice the bottom of the tractor with oil droplets, and no lines near by, it's...

I have a Satoh Buck S470. It has been owned by my family since mid 1980's and some of the maintenance has been neglected. Noticing the front hub has been leaking. Do I need to replace some parts or seals on the front king pins? Haven't found much info on the front diff, besides thatvit uses...

My backhoe is leaking from one of the curl function hose joins behind the boom cylinder where the hose connects to the hardpipe. The trouble is i cant even get my hand in there to peel off the cable wrap to confirm if the joiner needs tightening or its the hose. Anyone had experience getting to...

John Deere 4300- I have this fluid leak in my left front tire area and was wondering what and where the fluid is coming from and how I can repair it. I am just guessing it is a seal gone bad in the front axle. Any thoughts will be appreciated. Posting a few photos to highlight the problem,

I pass along so it might help someone, seems kind of unusual. I bought my Mahindra 5010 used. After using it awhile, I started noticing some kind of fluid on the ground after I moved the tractor from where it was parked in the pasture the night before. But it seemed to be under the wheels, not...

I have a BX2200 that is leaking around the control arm for the pto at the transmission. I'm trying to remove the control arm to replace the o rings and have removed the bolt that goes thru it and the shaft and it will not come off. I don't see anything else holding it on and the service manual...

can anyone tell me what this part is called that is leaking and won't tighten?

After I disked the garden a few days ago I rinsed the polled off the tractor and then backed it into the carport to tighten a loose bolt on the disk. I did and pulled it back to the shed. There was some mud and water as I expected. I swept the dirt up and saw the "wet spot" . Later that night...

I recently had the chance to purchase a 1993 B7100 HST with a 60" deck and its my first time owning a Kubota. The tractor and mower run great, but I discovered a fuel leak that appears to be coming from the injector pump where it is threaded going to the cylinders. I have attached couple of...

Hello all. Well i was very excited to get my first tractor this weekend(I have only had skidsteers in the past.) Saw a great deal on a RK37 shuttle shift with 240 hours and I jumped on it. Guy said it had no leaks and I didn't notice anything while i was checking it out, but it was in the...

I have a Long 560 tractor with a hydraulic leak from the transmission case. The drain plug and two holes in line with the axles and drain plug are on the bottom side of the case. One hole is plugged with a bolt and jam nut. The other hole is wide open and the parts manual does not show anything...

A friend had a hydraulic leak on his 2350 and after removing the hood we discovered split/rotted small hoses running from what I assume is some sort of surge tank just behind the radiator. The tank is about 8" diameter or so and has a T fitting on top with barbed nipples where the two lines...

Recently acquired my first tractor, a Satoh Stallion, with a hydraulic oil leak. Split the tractor, removed the clutch, and the clutch release bearing (throwout bearing) with carrier, and hit a brick wall. I assume I now have to remove the clutch release yoke and shaft so I can remove the...

All, I noticed I my TC45DA is leaking/weeping hydraulic fluid. It looks like it’s leaking where the hydraulic pump bolts to the front cover of the engine and it’s not engine oil. Is there a chance that the hydraulic pump is just loos and that tightening the bolts will slow or stop the flow? I...

My 2006 new holland boomer has been using some coolant. I noticed the overflow tank was empty and was able to add a whole gallon of premix coolant directly into the radiator. I’ve never seen signs of leakage , and the engine oil is at a stable level and shows no sign of coolant present . I...

Just out of warranty (of course), I found an oil puddle on the ground below my pull bar. The RK mechanic told me that even if it was under warranty, it wouldn't be covered because gaskets and sealant are considered wear items. So I had a local independent mechanic fix it. There's a plate above...

Hey ya'll I'm back with another DIY farm repair, this time replacing the gearbox seals and bearing on a King Kutter 5ft PTO tiller. One day when I arrived at the farm I noticed a large pool of gear oil under the right hand side of the tiller. I ended up tracing it to coming out the tine shaft...

I have a 2022 dk42 that keep leaking for the o-rings on the joystick valve (where the hydraulic hoses for the loader connects). The first time it happened my dealer told me to just replace the o-rings (I did'nt want to make him come all the way to my house for a 0.25$ o-ring). It has been 2...

break out of these posts not sure why they show post title like that. https://www.tractorbynet.com/forums/threads/what-have-you-done-with-to-your-gc-series-2300-2400-1700-tractor-today.419677/post-6214846...

Hi, recently the clutch on my 6340 started to leak, dripping from the pedal inside the cab. Any of you ever have the same problem? Thanks

Hello, I have a hydraulic leak and I think the culprit is the shaft which is used to open and close (what I believe is) the hydraulic lines. Something has caused the shaft to have an oblong rotation and it also seems like it has more wiggle than it should. I've included a couple pictures. I've...

Hi, I have a 1989 Zetor 6211 for a few years now. I have done a lot of work to it over the years. the problem I am having is when the tractor is running there is quite a dropping leak of power steering fluid from the power steering ram. It leaks from the beginning of the ram from what looks like...