Tractor idles rough sometimes. We have cleaned out plastic fuel tank once and that worked for 15 months no issues. It has started again, so I changed both fuel filters and fuel pump. I even by...
Just wondering if there are some BX25D owners on TBN that till with them. I'm thinking of a tiller for this spring, and wondering what is a good match for that tractor. From what I've read, 48 is...
2019 BX25D. Suddenly, yesterday, it stopped going. Would not go forward or backwards. The foot pedals move as they should. The front and rear buckets work normally. Checked fluid, it was a...
My BX25D has been shutting off with no apparent reason. The engine simply stops. When I turn the key it starts right up again. It happens when I'm running the backhoe, or when I get up off the...
Hi, i'm looking for a copy of the service manual for the kubota bx25d. If someone could point me in the right direction it would be greatly appreciated. Thank you.
Hi, I just purchased a bx25d and noticed the tach doesn't work. When I start the tractor the digital tachometer needle sweeps to high rpm then rests at 0 rpm and stays there. I have checked the...
The dust boots on the front axel of my 2013 tractor are cracking and likely need replacement. Wondering if this is a DIY project or if I am better taking the machine to a dealer to have them...
Hi all,
I am looking to sell my 2018 Kubota BX25D.
I have been perusing equipmenttrader.com, craigslist, ritchie bros, tractorhouse.com and so forth.
the prices seem to be all over the place.
Do...
Hello I have a kubota Bx25d and they hydraulic fluid is foaming. Was told it’s sucking air into the system somewhere. Changed the hst cooler cover gaskets and all new fluid and filter and still...
I have a couple acres that are typically pretty wet, but with the dry conditions we've had this year, I think I'll be able to remove some stumps from small trees I've take down over the last 3 or...
I bought a used 2016 BX25D last year that had 200 hrs on it. I have put on just over 100 hrs on it since I've owned it, for a total of slightly over 300 on the meter. It has the R4 Industrial...
Kubota bx25d 200 hours. I had a small hydo leak, drove it to the garage and replaced line. While I was there I changed the oil and filter and the fuel filters and fuel pump. Now it starts but...
Hello everyone, I haven't been on here for awhile, good to be back. I have an opertunity to buy a used BX25D and was wondering what a fair price would be. I don't have pics of it yet, good...
Today I needed to swap out the backhoe for a tiller and when I was done and needed to reconnect the backhoe, I noticed the quick connect that goes back to the tractor from itself was hot to the...
Hi all. As a newbie to tractors I have a question regarding brakes on my kubota Bx25d tlb. I know the brakes are in the rear axle and they are wet brakes. I read somewhere that if the tractor is...
Who has one and what is needed for installing on my BX25d?
Dealer in NH is all over the place on what mods are needed to tractor for this installation. From what I can see in the manuals, the...
I'm thinking of buying a rototiller for my BX25D, and I thought I'd ask here for some advice. They seem to be pretty scarce, so all of my looking has been on line, only. I'm thinking I'd want the...
I'm sure this has been discussed before (?) , but I have a BX25 that I bought used back in March. I'm having a problem keeping the rubber pedal covers on the treadle pedal "REVERSE" side, and the...
I am looking to acquire a Kencove PD80 or similar post driver for my BX25D. Seeking advice on how to connect the fluid return to the reservoir as I understand the quick connects will not...
I love my BX25D there is nothing this little gem won't eventually do!
I have multiple 3 point attachments but my last switch back to my backhoe I found a 3" ish about 10mm hex head bolt on the...
My front tires were shot. They lasted five and a half years and 370.3 hours. The outer edges were getting worn, but that wasn’t the problem. I could have just switched sides, if I were to keep...
Hey all, here's my latest video (yes - we need chaps/chainsaw pants). It's getting warmer so its starting to be a lot more fun to be outside obviously ... for those rainy days ... I just took...
Hey everyone, here is my latest Kubota specific content. I feel I have solved an issue that has been bugging me for a while. Yes, it's set pretty far back and low to the ground, there may be...
I wonder if anyone else has had this problem: The steps on mt backhoe seem really vulnerable. I have broken both sides about three times, by backing into things. I'm getting tired of welding them...
I have a BX25D and have been working hard on installing a Land Pride 380-137A third function kit with no success installing as Land Pride intends. They specify the P port on the valve block be...
I'm new to the forum and tractor ownership here so thanks ahead for the help and I'll go ahead and apologize for being long winded here. I bought a 2014 kubota BX25D a few weeks ago and was hoping...
Can someone point me to a thread, or more detailed instructions(if they exist) for the task of installing this kit. I bought an everything attachments wicked root grapple, and need to install the...
Hi all, new here but have been sifting through the forums for a while now and love all the help and tips on here!
Second, couldn't find any information on here through the search (unless my...
I was in the market back then but never made a purchase.
This review material I created is 4.5 years old but may still be of use for someone today, I was unable to attach this PDF file back...
Hello. Just purchased at auction 2013 Bx25D with 550 hrs. Got the operators manual and WSM. Tractor was a Home Depot rental. I have the following issue. With the key off (rotated far left)and I...
I am wanting to put a Top and Tilt system on my BX25D but my dealer says you can't plumb your rear hydraulics to operate it with rear remotes on the BX25D because of the backhoe configuration. I...
I have a kubota Bx25d and was wondering if it is powerful enough to run a post hole auger? What size auger 9 or 12 inch? Has anyone have any experience with this? I don’t want to damage the tractor.
There must be a better way to attach the shaft from the mower to the PTO. Each Spring when I service my deck and attach it to the tractor it is a painful ritual until I can get the dang thing to...
Thanks for the great site. I have a Kabota Bx24d and I am new to these type of tractors. It is for basic home use. I consider myself mechanically inclined somewhat. My machine has around 300 hrs...
When going in reverse, or sometimes when turning sharply in forward, and especially with a load in the loader bucket, I hear an intermittent clunking noise from somewhere up front. The only...
Iv got a 2012 kubota bx25d,and was out plowing with it,pushed in the diff lock,hit reverse and now i have no rear wheel drive,checked the tires spinning in the rim,because thats happened before...
Thinking of moving up from my BX25D to the next size tractor the B2601. Main issue is space in the shed. Anyone know the LOA of the BX when parked from the tip of the loader bucket on the ground...
Anyone make this move? Thoughts? My 2014 only has 75 hours, I have most of the BXpanded upgrades and wheel spacers, etc. that I would keep, my current tractor also has the dealer installed Land...
Is it normal to have no empty bucket movement unless the tractor is up to about 2000+ RPM? I understand you should run it at around 3200 RPM when in use, but I was surprised there is no apparent...
Looking at a Kubota BX25D in what appears good condition with a leaky bucket tilt cylinder, everything else seems good. Hours are estimated at 300, instrument panel replaced so actual is unknown...
Just took delivery on Saturday of my almost new 2016 BX25D with 42 hours on it.
Tach needle reads approx 500 RPM whether the engine is running or not. THE TACH DOES NOT WORK
All of the other...
I tackled this rock for learning experience. Fairly easy to pluck out but right after the photo was taken, the rock fell down into its hole, protruding with round end up. I couldn't grab it again...
After having a stick go into the HST cooling fan on day 3 of owning the BX25, and going through the process of replacing it... I decided that I needed to modify the factory steel shield so that it...
I was using my tractor's FEL today and I heard a loud pop up by the FEL while having the bucket about half way curled against the ground pulling backward. Immediately afterward, I can curl the...
Since I have the 60" mower deck on, I have the BH stored so I needed some ballast while moving some dirt etc.
Looked in the scrap pile and found a nice piece of "hanger steel", I'd been saving old...
Apparently I am clueless. I picked up an auger from tractor supply and went to put it on. The A frame does not reach the lift arms. Is there a special 3 point hitch extension for lift arm...
Hi, I'm new to the forum and have recently purchased a 2013 bx25d with 260 hours, that I'm getting to know. I am bulging a house and plan to put it to work shortly but for now it's in storage...
I have a kubota bx25d that was sputtering. I changed both fuel filters, no change. Now, it will turn over but not even try to push any fuel. I drained the fuel system, just prior to the rear...
Either machine could do for what I am looking for, but I am not really that impressed with the BX25. I mean I was ok with the BX until I tried the GC. Then I also compared the specs and wow. I...
I'm trying to finish a chainsaw mount. I tried to use click bond fasteners to avoid welding/drilling, but can't get the epoxy to hold on one of them so I'm moving on. So can anyone identify this...
Anyone have the dimensions and geometry for the pins/lugs for the bucket on the backhoe? I want to fabricate a trencher that mounts on the same attach points.
Who has done it? I would appreciate pictures showing the valve location, hose routing and connections. I thought I had decent routing, then realized my connections are short.... (the P and T...
Just finished up a project I've been working on off and on this winter. I have the factory LED work lights on the ROPS but I wanted to keep them aimed forward and add some additional ones pointed...
Getting to the nitty gritty. Like the slightly bigger overall size of the Massey for the majority of my jobs. (5 acres, no mowing, lots of use with the FEL dirt and wood chips and some digging...
It almost appears as if there is or could be an additional fuse block installed under the factory installed block. Is this the case or? And even if not could I not just buy another fuse box...
Got a 2015 BX25D that started sucking air intermittently couple months ago. Strange to me it's not all the time (at least that I've noticed) and that it doesn't always, until recently, cause power...
i am shopping for a compact tractor, i was looking at a bx25d and noticed on the loader lever 2 red buttons. what are those buttons for? thanks for your time !
Hello everyone! Hopefully someone out there can help me out.
I've been searching around on here finding some very useful info so decided to join the forum so maybe my story will assist someone...
Have a BX25D with about 400 hours.. Just recently the loader started leaking down when the engine is running.. Kill the engine and everything holds as well as can be expected.. Any ideas on where...
I've had the 2660 for about 5 years, mowing mostly (54"MMM), but also building and maintain gravel driveways (FEL & box blade), general FEL work, and a little brush hog work with 48" LandPride on...
Yeah, I just got it and I'm already trying to break it. :D
I have the 12" bucket on it, but I'm working on a drainage project and I need to dig an 18" trench 18" deep. Is there an 18" bucket...
Today I negotiated a Kubota BX25 with backhoe, 60 inch mower deck, front loader with quick change, and a canopy top. It was a opening day special and I got it all for $19,400 and 0% financing for...
I know there are several posts on here about this comparison. I thought I had made my decision on the 1025R however over the weekend I obtained a price quote for the Kubota BX25D that caused me...
I just got my almost brand new BX25 back from the dealership.....the lower seal blew on the lower backhoe boom and they repaired it under warranty.....I checked the hydraulic fluid level before I...
I have a new BX25D and a new Land Pride rotary cutter.
As a newbie on tractors and attachments, I was trying to hook up the cutter to the BX25 but I think the driveline may be too long. As I...
According to the manual and my tape measure, the outriggers measure 51", in their up position. Does anyone have any ideas on how to get it through a 47" gate? Let's pretend making the gate wider...
I'm a little annoyed.....I just bought this BX new in November of 2015....it only has 20.8 hrs on the tractor and this was my first real time using the backhoe on this tractor....I had pulled a...
I cut down some trees where I will be storing my equipment so that I can have a circular drive....I love the grapple claw...only one small problem...an o-ring on the hose connection to the 3rd...
I did my first real backhoe job, today. In the past, I had pulled a small stump and removed some small bushes, neither of which took more than a few minutes or required much actual digging...
I am going to be a new owner of a new BX25D. I've been reading online manuals from Kubota that say that you can't operate the belly mower while the backhoe is attached. Yet, I see youtube...
I have a BX25D which has been very good to me over the past two years, but my wife just now told me that she is tired of the hydro rocker. She is very small, and when she moves the seat to the...
While mowing, cycling deck up and down, when the deck comes to rest on the deck hight cam, sometimes it lowers a notch. If I don't pay attention, by the time I'm done mowing, it will be 2 or 3...
I took some time to mulch my backyard.....the Wife won't let me cut any trees down, so I decided to just mulch it instead of establishing a shade tolerant grass...
Kubota BX25 spreading mulch -...
Hello all,
I have a new bx25d with < 10 hrs. Yesterday, I ran it around the yard for about 20 minutes to check the adjustment of the mmm prior to the first mow of the year.
After finishing, I...
Hi folks, sorry for the stupid question but I purchased a 2104 BX25D and the Kubota Dealer indicated that it comes with a block heater. I cannot for the life of me find the pigtail. Where would...
Hi folks I recently bought a BX25D loader/backhoe.
I went to use the tractor for first time. Has about 110 hours on it.
I noticed the loader hydraulics really slow even with the RPMs up. My...
Hello from Sydney, AUS. I've had my new BX25D for a week and I've scratched the paint on both buckets :thumbsup: Yes I need to take some photos. My first job is to make it a home so the wife's car...
They delivered my first "real tractor" yesterday. And by real I mean with a 3-point hitch and rear PTO.
Now, I'm eyeing up a few add ons. Like work lights, cutting bar for loader bucket...
Hello there. My wife and I are looking to buy a little tractor-loader-backhoe that can do a lot of work, a little bit at a time. We bought a short sale on 5 wooded acres that has been neglected...
Hello everybody,
First post on here and first tractor I ever owned. Was just wanting to see if you guys could help me out on a decision I am making.
I am about to place a order with Compact...
Does anyone know where to see pictures of the factory accessories available for a BX25D? I have torn up Kubota's website looking for a brochure of some sort that would show this and found nothing...
Hello,
I just purchased a BX25D that should be delivered later this week.
After living in our house with 2.6 acres since 2007, I'm finally getting a 60" mower. I bought a used Cub Cadet when we...
We finally got some snow, not much, just over two inches. It was enough I didn't feel like a fool out playing on the tractor, for the first time, in snow. Took it from 5.6 hours to 11.8 hours...
I'm up to just over 5 hours on my machine. Not much, I know...real job and inclement weather (rain and low temperatures, not tractor weather) have kept it in the garage.
I put it in the...
Hey Guys
Just a after a bit of advice before I have to call the dealer (who I have next to no confidence in)
I have 2 leaks on my relatively new (30 hours) BX25D - this (red) fitting on the...
I got one! I got one!
Got the TLB with a 12" bucket and the 3 PT kit. I added the Land Pride RB0560 rear blade. I got a little more off than originally offered because they didn't have the...
After the deal falling through in April, I am thinking I'll try again, tomorrow.
The price has actually gone down, from April and there is only $65 difference from cash to finance price...
So, I'm talking to my dealer about buying either a BX25D or B2601. From what I gather, you cannot raise or lower the MMM if the BH subframe is in place. They recommend having either the MMM or...
I have never owned any tractor. But I need a SCUT for 2.5 recently purchased mostly level acres of pasture, plus some digging and landscape projects. I looked at the John Deere 1025, Kubota BX25D...
Could someone point me in the right direction ?
I'm looking for the dimensions of the backhoe bucket on the BX25D. Space between pins, pin size, and how wide stick on the boom is?
I want to...
I just finished up designing a snow plow for my new quick attach FEL on my kubota bx25d. Again, I will attach all of the Solidworks files and dxf files if you want to make one. I don't really...
I think I'm going to keep the seat secured while towing. The constant vibration and bouncing is distracting to me while trailring. Do you think securing it will harm the seat micro switches that...
I've not had a chance to use my new backhoe very much since I bought it a month ago......I was fitting my new trailer to my "new" dump truck today and was pulling the tractor up on the trailer...
Took a BX25D for a short test spin last week and had some questions. 1. Is 1500 rpm really the idle speed and if so, why so high? 2. How difficult is it to attach the 3 point arms after removing...
I am going to purchase the under armor shield for my 25D in order to protect the "guts" of the tractor from damage when clearing brush. I watched a couple of videos on how to install this, and I...
I took delivery of my BX25D today.....I got a package deal which included a Quick Detach bucket and a LP Grapple claw with 3rd function valve, skid plates to protect the belly(figured I'd take...
Hi
Wanted to for some general advice regards purchasing used v new
Thinking off buying a Kubota BX25D for using around our acreage and doing a few jobs i have planned. Was going to hire one for as...
I like the idea of having a backhoe, but to do so, I'd have to settle for a slightly smaller tractor in the BX25D......adding a new BH to a B2601 would take another ~$7K....yikes......here are the...
Had it at the dealer for tubes in the front tires and decided to do the whole hog service. Had the fluids and fuel filters changed and they went through it and serviced everything including...
This weekend, I went to visit my friend that just bought a new BX25D. Me I have since 1977 a B6000 with a back hoe and a front end loader. My friend made me try is new tractor. I was very...
I have a 2015 BX25D that I am interested in Selling.
Add ons:
land pride grapples w/ 3rd function valve,
3pt hitch
backhoe thumb
bucket hooks.
Tractor has about 40 hours on it.
grapples are...
Hi folks,
I'm looking into purchasing a new BX25D. I have access to a used BX2750 snowblower with mechanical chute, any ideas if it can be adapted to the BX25d? It came off a BX2200.
Hi Guys
Got delivery of my new BX25D today - looks so good and so shiny I'm not going to want to get it dirty!! Just want to say this forum has been fantastic in my pre-purchase research, thanks...
I recently sold my L3540 with LA740 FEL, Pallet Forks, and rear blade. The main reason was it was too big and heavy for the tasks I had planned except when it came to moving snow. I couldn't mow...
I have a new BX25D and want to get a post hole digger for it. One came up on craigslist w/a 9" auger bit, a Model 65 SpeeCo. They make a sub compact unit as well, but I'm wondering if the 65...
I am a newbie.
When I bought my tractor, I didn't think I would ever take the BH off, so I decided to not get the 3 PT hitch kit.
Well, now I know better and I need a kit.
I know I can go to...
In another thread there was a discussion re: whether or not the new BX series has engine or trans braking.
I am far from an expert and I can only speak to my BX, but the transmission or engine...
Well we finally pulled the trigger and Barlow's should be delivering my new SCUT the week of the May 25, 2015. :thumbsup:
Went to Barlow after reading all the good stuff here and comparing prices...
Well, hopefully I'm not the only person who has ever done this, but when I was re attaching the backhoe I messed up pretty good. Lucky no one was hurt. When I backed the tractor up, I guess the...
Retired Hurst 7000 gvw trailer, built in 2005, but only used twice. New load range C tires..I'll do a new paint job and treat the wood deck. . A little overkill maybe.. but for less than 1600...
Just got a quote...
New BX25D-1 with standard loader/backhoe, 12" BH bucket, thumb, 3 pt hitch, 60" MMM, R4 tires
Out the door cash price (after $1000 instant rebate) $18900 delivered
thoughts?
hi All,
getting within a few months of making my tractor purchase.
I am struggling a bit with my decision and here is why:
1. I have hilly property and I want to be able to use the tractor on...
I'm still pondering on a scut, recently priced the bx25d 24000! and asked the kioti dearler about a ck2410 with hoe that he had on the lot, his price was more which surprised me, he went on to...
Being the proud owner of a BX25D and it helping me get things done around the homestead quicker and some of those planned projects are getting completed, I am thinking about picking up some small...
1025R vs. BX25D-1 vs. Max 24 vs. GC1705
First post. I've been trolling the forums a lot lately.
I also have been search around everywhere and I know this forum has a very similar thread.
With...
I have very hilly property. If I have to operate on a side slope, I have noticed that the machine seems to run rough when the left side is uphill vs no change if the right side is uphill.
I...
I have been on the forums for a few months now, but not much activity beyond my "what should I buy?" thread. Ended up not buying anything presented there anyway.
I have a lot of earth moving to...
Hey guys, I bought my Bx2370-1 last year and I just did the 50 hour service. I JUST LOVE THIS MACHINE. Well I always planned on adding a loader but it looks like my financials are going the...
I got a lot of cleanup and landscaping to do with my 3 acres, and I would like a tractor with MMM, FEL and BH. So I have talked with the local (1.5hr) mahindra dealer and the local (45mins) kubota...
What model tires come on a new BX25D-1? I was leaning toward R4's, but am now going back to thinking R3's. Most of my work will be on the lawn: mowing and landscaping the edges with the BH and...
I have a 2014 Kubota bx25d with the standard Kubota backhoe. I have put about 150 hrs on the tractor, and the backhoe gets a lot of use. Since it was new, the right stabilizer has gone up and down...
I go for "orientation" tomorrow at the dealer and then delivery next a.m.. I'm surprisingly giddy. Options are the 5450 blower and the "thumb". Turf tires -- hope I don't regret that choice...
Howdy,
Have been a lurker here for a while, and finally decided to pull the trigger on a new BX25D-1, and went with Barlow's due to the overwhelmingly positive feedback I saw on here. It was...
It's a 2014 rental with 156 hours. Both buckets are well worn but that doesn't matter. What should I be looking at for problem areas? Would you stay away? Price is $15,900. Thanks.
Recently had a factory, block heater installed while the BX was in for warranty work and it functioned great until yesterday when I had left it plugged in for a longer than usual time. Tractor...
Anyone have a few pics inside and out of the factory Kubota toolbox that mounts next to the seat arm rest that you can share? Can it be mounted on either side? thanks
Hello,
After almost buying a used BX25, I have decided I am better off buying new. (Only a $1,500 difference)
Can someone take some pictures of their BX25D-1, for me? I have several good...
Does anyone out there have any experience using a BX25D or similar with a 5' rotary cutter? I'm primarily interested in mowing tall grass along fence lines. The 5' width appeals to me so I can...
Greetings,
Have a new LandPride SGC05 grapple on a new BX25D. I need (2) male and (2) female dust caps to protect the Quick Connect hose ends when not using the grapple. I called...
I traded in my BX2350 that I bought new in 2009 on a new BX25D-1. I used it for the first time today. I dug a 20" trench 90' long for my propane line. I also buried what was left of a brush pile I...
I was quoted $18,800 for a new BX25D-1 at my local dealer here in Oklahoma. I called another dealer 30 miles away and they wanted $19,500 for the same setup. Basically a 25D with three point arms...
I went to install wheel spacers on my new BX25D yesterday and ran into an issue. The rear spacers went on fine.
When installing the first front spacer, as I tightened the spacer to the hub...
Will came down yesterday to pick up plow. Used the BX25D to get it out of my storage building the plow was behind a 4' high stack of 3'x3' carpet squares. I lifted it with a tie down strap and got...
Greetings, does the new BX25 have a float function? If so, how does it work? I saw mention of it in the manual, but could not find mention of how to put the bucket in float. Thank you...
My manual on my new BX25d states 17psi for the rear tires and 22 for the fronts, but I thought I recall seeing a max pressure on the front tire of 100+. What's the recommended pressure? Thank...
Good day today. I picked up a new Sure Trac 14' 14k lb dump trailer. It's very well made, great fit and finish. I opted for the scissor lift, wireless remote, spare tire and best tarp kit...
On removing the belly-mower the mid-PTO coupling and shaft was left coupled to the mid-PTO. On starting the tractor, the PTO coupling shaft proceeded to destroy the filter, which broke off the...
Greetings, I'll be picking my my new BX25D in the next week or so and Trailering it 150 miles home. What are the best tie down points? I'd really like to install 4 dedicated tie down rings at...
Which is the better thumb for a BX25D BH? The Kutota for $375 or the BXpanded for $319? Seems the BXpanded is very easily adjustable, how about the Kubota? thanks
Greetings,
I'm getting ready to purchase a new Sure Trac low dump trailer for a new Kubota BX25D. The removable ramps look like this:
The front tires on the Kubota are only 18x8.5-10, and...
Greetings, Getting ready to order a new BX25D (FEL and BH) along with a Sure Trac 7x12 dump trailer. I measured the overall length of a BX25D last week at the dealer, it was about 13.5' with...
Greetings, getting ready to purchase my first new tractor, a BX25D. When I build/price it online it's about $21.5k. When buying locally, what is a reasonable "deal"? Is ~10% off MSRP reasonable? I...
Hi all,
I'm still relatively new to this tractor stuff (but am loving it so far). Recently I bought a 3PH log splitter and hooked it all up to the back of my BX25 using the hydraulic connections...
Hi, new here to forum and to tractors in general.
Just ordered a new Kubota BX25D. Excited to be joining the tractor world. I bought about 7 acres of property 2 yrs ago (mostly wooded). Looking...
Attaching some pics of the work my BX25D did with a little help from me.
Dug out south end of basement wall to footer, applied sealer and weeping tile along wall/footer, filled back in.
I have been searching on the web for the WSM for my BX25D. Can't find it. Visited Messick's, Kubota sites and a few others. Anyone know the part number and how to get ahold of it? Need parts...
Just thought i would post my bx 25 bx 25d story. i live in north east Oklahoma and recently i have been trying to reduce my monthly bills. so i have been refinancing all of my loans and paying...
Hey Ontario, Canada
My house insurance broker wont provide me fire theft insurance on my new Kubota, and neither will my car Insurance broker ...........AnY recommendations ...
I have a 2008 Kubota ZG222 with 48 inch mower deck. Can I put the deck on my 2014 BX25D's mid PTO? I have some areas that I need the 4wd to get to be able to mow. The ZG222 gets stuck way too...
Thought I'd share a pic of my new garage and my BX's new shelter...the BX can go into the garage if needed but for now, sheltered from the weather is adequate.
Am looking to buy a bx25. If I get the quick attach for the loader arms, will the kubota forks (k9184) go on the quick attach or do these forks need a sub-frame? Thanks.
Anyone have a Piranha tooth bar and used it for scraping weeds off at the ground? these little suckers around here are like your finger at the base and a few feet tall, and very prickly. I just...
I just picked up a Kubota BX25D sub-compact. I also ordered the 60' snow blade for clearing my drive and access road. I have almost level ground here in N. Idaho, 300' winding drive and 2000' to...
I am waiting for delivery on my BX25D. I ordered the 60" snow blade to plow a 300' gravel driveway, and approx 2000' gravel road to the street. Here in N. Idaho we probably wont get more than 12"s...
I done some shopping around this past few weeks and finally decided on the BX25D compared to the Kioti and Yanmar in the same category I think the better deal was the Kubota! My 1st tractor was a...
I like the JD1025R, with its easy attached mower deck, but no thumb available on the back hoe. The Kubota BX25D has an adjustable thumb for its back hoe, but a more difficult attach job for the...
They sure did make it look like the pins were easy to take off on the youtube videos lol. Actually they are except one backhoe pin, my dealer is a 2hour drive from me and its nearly impossible to...
2013 kubota bx25d with 50 hrs. has loss of power . idles fine as soon as a load is put on it it want's to quite. thought it had water in fuel so changed all filters added additive and fresh fuel...
My son in law has a BX25D and wanted to know if there was a grass bagger attachment available for the 60" MMM?? Any and all help would be appreciated. His machine is a 2013 model year.
I've seen where people added, say to a Curtis Cab, a heater with a valve to shut off the hot water flow, which I would like to know more about the brand of heater....but, I have not seen where...
Hi All, Just wanted to share. I ordered the BucketSolutions, clamp on hitch. I really liked the design so I ordered it. I want to move my utility trailer,boat and camper around without pulling...
After wanting a small tractor for about 2 years now I finally ordered a Kubota BX25D this morning. I should be able to have it delivered next week.
The way my wife works is she never wants to...
Hit 50 hrs on the meter while mowing Monday. Planned to finish up mowing yesterday after work but had stormy weather, so I decided to do some of the 50 hr service instead. Wound up doing...
just wanting to get some information about the BX25D that I hadn't considered earlier (when I was looking at the B3030). we need optional pallet fork operation on the front, and post / fencing...
Wondering if there's enough room to let a little air out for mowing? I have a bumpy lawn and the seat bottoms out under my hefty weight. Never had any experience with filled tires except knowing I...
Never owned a tractor before! I have 4-5 acres of land mostly cleared. I am looking for a tractor to do general work like dig drenches, dig for pond, clear some stumps! I was looking at the above...
Noticed a few drops of oil under the front axle today. Left side of power steering cylinder leaking oil at 38 hrs. Will be stopping at dealer Tuesday to arrange for repair, but just wondering if...
I was riding my bicycle about and sometimes I make a point to ride by the Kubota dealer to look at attachments. I was studying the design of the backhoe on a BX25D. Some fellow drives up and parks...
Today I was working on cleaning up the property some more and figured I really only have one stump left so I may was well take it out. It is sort of on the edge of the woods but figured if I am...
Hi,
What is the difference between a Kubota BX25D and the newer BX25D-1?
If there is already a thread covering this, sorry I couldn't find it!
Thanks,
Duncan
The dealer dropped off my new BX25D at my house Saturday morning. Saturday and Sunday I put about 6 hours on it digging out boulders and rotten stumps where the yard meets the edge of the woods...
Turns out to be a major P.I.T.A. (if ya know what I mean...
Zero instructions except an exploded diagram of the whole backhoe...have to search out the little bits and parts for the thumb and the...
Well yesterday I mowed with the little thing for the first time, hope do to an update in the day in the life thread later today.....and took everything off the tractor for the first time, well I...
Trying to figure out a place to put a tool box on this little thing. I just can't seem to find a spot, or box for that matter that seems to work. I generally use old ammo cans for boxes on...
Nope, not looking at which one to buy but just some thoughts. We recently purchased a BX25D to help with small chores around the house and take care of things the MX5100 does not do as well...
... in particular the "specially reinforced fame" ... what exactly is beefed up? What are the differences in the loaders? .... I might have missed something but the specs looked the same. I sat on...
I've had my BX25D for a week now and I am pretty impressed with what this little power house can do. With15 hrs on it I used it to help my brother do some rough landscaping at his new house. We...
Has anyone looked at the DR ripper for their backhoe? I was looking on the web at DR stuff and noticed they have a ripper tooth. I started thinking I wonder if I could get that to fit the BX...
Good morning!
We are in need a of BX24D for R & D for a new mechanical backhoe thumb. It must be a D model since we will make it mount to the same location as the factory accessory does. We would...
Good morning!
We are in need a of BX24D for R & D for a new mechanical backhoe thumb. It must be a D model since we will make it mount to the same location as the factory accessory does. We...
I noticed our new BX25D seems to let the backhoe leak down if I don't pin it in place. If I leave the tractor overnight the backhoe droops down to about a foot off the ground. Just was wondering...
Was looking at new BX25D and new Mahindra eMax 25, w/ backhoe, then saw BX25D loader, mower, backhoe under 200 hrs, backhoe never used, almost no scratches in FEL, 60" mower has most use for...
This post is basically about this: If a dealer sells you a tractor he advertised as an "A" but really is a "B" being sold as an "A" and the buyer (me) really didn't know the difference at the...
Hi all,
I'm hoping to get some feedback on implements. I'm new to operating (~50 hours on my BX25), have just bought a chunk of land, and will be:
- Having a house built (hiring a builder most...
Hello,
Doing my 50 hour service. I noticed a hose coming out of the coolant over flow tank from the top of the yellow cover. It is just hanging not connected to anything? Is this correct? Did not...
Note...I didn't order a mower as I already have a zero turn.
Kubota BX25D-TLB 23hp tractor
Front loader (LA240)
Backhoe (BT602)
48" front loader bucket
8" backhoe bucket
BX2506 Three point hitch...
BX25D was finally delivered today. Block heater is still on backorder. Was able to do a little digging today, though it was cold and the ground is pretty mushy. Pics at delivery.
Pics after...
Thanks to everyone that helped answer my questions and gather info on the 25D. Tonight we brought it home and used it around the house a little. Worked great, smooth and strong for a small...
I just ordered our BX25D and am interested in seeing how the HST fan is arranged. I understand it is vulnerable but have not seen any photos of them and was wondering if anyone has made a plate...
We are very close to buying a new BX25D, mid mount 60" mower, thumb, loaded tires, with the 3pt hitch. My question is does anyone not like their BX? We want it to replace a B7200 we used for...
Well I have had the little machine a grand total of 4 days, Machine arrived with 3.8 hours on it and now (IIRC) has 9.6. So far it has been a source of great fun and has done things I would have...
Pulled the trigger on a new BX25D today! R-1 Tires, 60" mmm, thumb, 3ph kit, ROPS mounted work lights, fluid filled rear tires, and block heater. Thanks to all who offered pricing comments in...
I'm seriously considering trading my 2005 BX1500, 1200 hrs, with 48" mmm and LA181 FEL for a new BX25D TLB with 60" mmm, mechanical thumb, 12" bucket, 3 ph kit, std ROPS mount lights, block...
Price for this unit is $16250 with financing as advertised. Seems like a new unit with 0% for 60 months may be a better deal than this one?
Kubota BX25D Demo unit | Johnson Equipment Company
Was wondering what if any differences from 2012-21014 on bx25d. Is year important or hours for example how much more is a 2014 worth over a 2012 (5 hrs)basically full warranty.thanks in advance
Does anyone have the new snow blade that mounts to the loader quick attach? I'm assuming its manual angle? If it is I wonder if it could be easily converted to hydraulic? Does anybody have any...
Hello all! I will try to make this as brief as possible. My wife and I have recently moved out of the suburbs to a beautiful 4 acre semi wooded lot. My driveway is around a 1/4 mile long and...
I'm considering a trade into a new BX25D from my '07 BX24 with 750 hours.
The Deal is reasonable to me and hoping my wife agrees (another Pinot Grigio please bartender)
This year I picked up a...
I'm a tiny bit less of a newbie than I was this morning. Got a quote from my local Kubota dealer on a BX25D. Too high for me, but I went in and looked at it today and got the backhoe dirty...
We have a four-acre piece of property with a load of projects waiting to happen (and potentially some more property coming online). We moved in last November and are now embarking on our second...
New to the forum, I've read a lot of good insight so far - Thanks! Little back ground first - small property but a lot of 'projects' over the next two years that a small machine would come in...
Twice now I have broken different welds on the 3pt Sway Links (the welds from the loops to the nuts).. In examining the rest of the welds, they are all pretty poor... Anyone know of an upgrade for...
I was looking for an earlier thread on this, but could not find it. Has anyone actually put the new BX25D FEL quick attach on an earlier model BX25? They are supposed to not be backwards...
Just got my new BX25D, I'm more comfortable using CAT controls. Whats best way to convert controls? Will it hurt machine to convert, not sure on new BT602 backhoe? Thanks for any help!
Today I finally tackled a big partially rotted fir tree stump. When I started, I wasn't sure it was possible. The challenge was that it was on a very steep grade and needed the stump to go so I...
Got a very slow front tire leak after 70 hours. I don't see anything wrong on inspection. Suggestions? Filled twice with air during 1.5 months use. What are my options?
Okay I have been using my BX25D for just under a month and I just hit 50 hours and it's time to service it. I have read some great posts on the subject but unfortunately I didn't bookmark them...
Hello, Im new to owning a Kubota BX25D
I am wondering if there are different size nippes on my kubota? My grease gun seems to fit some but not all and im wondering if i am doing it right.
Hi there,
This is my first "real" tractor purchase. It's being dropped off after work today. The sales guy said he didn't think the process would take very long at all (20-30 mins start to...
Okay folks, I have an acre of sloped property. Some have already seen a bit of what I am dealing with but here is another question. I am planning to terrace as necessary using Allen Block...
This almost could be a commercial... but in reality, just a sequel to my recent and now obsolete thread, "First real day on BX25D - need encouragement"
I now have 27hrs on my baby and couldn't...
I am mostly keeping in 4WD all of the time and occasionally locking the differential when needed working on the slopes of my cleared property. Today I was driving across, turning around a bunch...
Okay this might be a stupid question, but someone said there are no stupid questions (I can't say I am a subscriber to this) but here goes...
I have just finished cutting in a 200ft long by 6ft...
Took a little time to hose off my dirty new BX yesterday and noticed moisture under the glass on the instrument panel. Didn't use pressure, just basically a rinse. Is this normal? Anyone else...
Okay, I finally had a chance to get my new BX25D dirty today. :licking: Full disclosure first. This is my first tractor (other than a JD riding lawnmower). I have a sloping some places very...
I layed down some cash and "ordered" a BX25 D on the 30th of May.
My dealer said it should be in within 2 weeks. Last week he got a little short on the 14th when I asked where it was...
My new BX25D is <2 months old and has just under 80 hours.. Been working her pretty hard.. Yes I knew the risk of shredding the fan but after crawling under the tractor and evaluating the stock...
I need a favor...
I'm trailer shopping right now, and need to know the total length of the BX25D with the FEL and Backhoe attached but in the stowed or shortest configuration.
If anybody has...
Originally started to look at the BX25D with backhoe and loader, and a JD 1025R with backhoe and loader... then thought about going bigger to the JD 2 series, the 2520R (but they are phasing...
I just purchased a new BX25D. I have less than 10 hours on it. I'm having issues with the seat latch not latching but my big problem is that after using the loader for half an hour or so the...
Well, I shook hands today on a reasonable deal on a BX25D with option of 3-point hitch and adjustable thumb for the back hoe. They are going to prep it for delivery on Friday afternoon. Although...
I'm looking at a local dealership that has a brand new 2013 BX25D. It comes with 60" mower, 3pt hitch, fel, backhoe and I believe 8" bucket. I am looking to finance with the 60 month 0% interest...
Back in 2001 I bought a BX23 and loved that little tractor until work called me back to the big city and I had to let it go.. Here we are 12 years later and the family and I have once again shed...
Does anyone know what the difference between the brotech plates (looks like you need to get two to get the same protection?) vs the bx expanded uderarmor plate? I don't really care about leaving a...
I've been lurking for quite some time and am almost ready to pull the trigger on a bx25d. This will be my first scut pirchase as well as first big mowing deck. Ive been encouraged by my neighbor...
Hi, new to the forum looking for some advice. Got my search down to these two tractors. I'm building a house this spring. I'm renting or hiring out the big work and looking at these two tractors...
Good morning to all..
I wasn't sure if my new BX25 was going to do all that I wanted her to do. But, so far, She has surpassed!!! All of my expectations!
I do 100 face cord of firewood per...
I'm calling this mod #1 although I already got a few others done but I'll post on them later.
This is a ripper tooth I fabricated. It's pretty well built from scrap around the shop. It weighs 36...
What are the differences, if any, between the FEL on a BX25D and the FEL on a BX25 or BX24? Not including the QA. Any design, structural or metal size differences? Cylinder size?
TIA
:thumbsup:
I am not sure what to label this, a BX25D or a BX70.
I see a different seat, what do you wanna bet it works better
than the BX25 seat, which I dislike. We shall see eventually.
The...