Search results

Hi all, I have a 2004 New Holland TC35. Many years ago I bent the tie rod out in the woods. Recently, the tie rod separated from the tie rod end, the likely result of the threads eventually stripping from uneven pressure on the assembly. Bought a new assembly (the rod itself along with the...

Hi All, PLEASE GO TO THE BOTTOM OF THIS THREAD if you are looking for a SOLUTION to fuel levels dropping inside the fuel filter assembly during tractor use. You are, of course, welcome to read the entire thread. I have been having a persistent problem on my 2004 TC35. When I run the tractor...

Hi all, So, here's the problem. When I'm operating my tractor, the diesel is the fuel filter bowl slowly drops. If I don't pay attention, it can get low enough to eventually cause the tractor to stall. The only way to refill the bowl is to loosen the threaded ring that secures the bowl to...

I occasionally have to take my tractor onto the road to get from one property to another. Partly because of a chronic problem with my OEM flashers (they keep shorting out), I decided to add a separately circuited set of flashing beacons onto the light bar I built for my tractor. I just...

I occasionally have to take my tractor onto the road to get from one property to another. Partly because of a chronic problem with my OEM flashers (they keep shorting out), I decided to add a separately circuited set of flashing beacons onto the light bar I built for my tractor. I just...

I cannot figure out what's wrong with my hazards/turn signals. There is short in the system, and only to this one circuit. Every time I try to insert a fuse, it sparks and burns out immediately. I disconnected the quick connectors to each of the rear lights/flashers to ensure that the short...

Greetings all, I've had the best luck with my 2004 TC35 Boomer. 18 years now and the only thing I've had to replace (short of routine maintenance items) is the starter and the ignition switch. I'd say that's a pretty good run. Question: Where could I find a replacement instrument cluster...

If anyone has any leads on locating a used 2004 TC35 instrument cluster, I'd appreciate it! Thanks all.

Hi all, So my 2004 TC35A (about 3000 hrs) was out doing some brush hogging when the tractor began leaking coolant. My wife was mowing (I was at work) and she managed to get the tractor up to the barn. It was losing power as she drove. When I came home from work, I went to investigate. The...

Hey all, Small tractors can accomplish big things, as in the construction of his barn complex between 2004-2006. My TC 35 did nearly all of the heavy lifting for this project, including lifting the main LVL's for this barn using a gin pole assembly. The only thing it couldn't do was lifting...

Back in '04 I should have gotten the cup holder for the boomer series New Holland. I have a 2004 TC35, and after all these years, have decided I really need a holder for my cold or hot drink. Picked up a couple of these plastic holders at the local auto parts store, and affixed one to the...

So, my glow plug timer relay on my New Holland tc35 needed replacement. It's mounted to left of the steering column (when sitting in the operator's seat), under a fiberglas cowling that one would never think to remove normally. Four bolts later, the cowling came off and this is what I saw...

happy holidays all, So my 2004 TC35 manual began losing power yesterday when plowing. As if there was a sudden interference with fuel delivery. I managed to get it into the barn. Could not get it to restart (acting as if it was out of fuel). Removed the fuel filter and replaced, added...

Hello all, So I decided to try a Bro-tek bolt-on mechanical thumb for my Woods 9000 backhoe. Purchase and follow up from the company was easy; the company uses PayPal. It comes down from Canada; took about 7 days from order to delivery. Installation was a breeze; it took all of about 10-15...

Good evening all, So I have 2004 TC35 12/12 with 2503 hours. Has never had a serious mechanical problem. Just this week, when I turn the ignition, the starter does that grinding spin and doesn't engage. At first sporadic, but now happening with increasing frequency. Is it inevitable that...

Hi all, So I have a 2004 TC 35 that suddenly won't start. I have checked to insure that the PTO and other safeties are not preventing starting. Tractor was acting normally in every way until today it would not start. Battery seems fine. I'll check the connections tomorrow, but I doubt that...

Hi all, I have a 2004 tc35 manual (12/12) with about 2600 hours on it. Over the last couple of months, I've noticed that I am VERY SLOWLY leaking a small amount of hydraulic/tranmission fluid out of what appears to be the seal surrounding the driveshaft in the rear of the tractor. And it is...

Hi guys, Just bought a decently maintained 1999 Wood BH9000 backhoe. One of the swing cylinders is weeping hydraulic fluid, so I pulled the cylinder and I'm about to call around the local shops to get estimates on repacking the cylinder. It's a three inch diameter cylinder, about 15 1/2...

Hello NH owners, I'm about to purchase a used Woods BH9000 backhoe complete with it's subframe kit. The BH was used on a 2000 or 2001 New Holland TC40. I have a 2004 TC35. Can anyone out there tell me if the subframe kit that clearly fits the TC40 will fit my tc35? I haven't had a chance to...

Hi all, I have a 2004 New Holland tc35 4wd tractor with the 16 FEL. After 8 years and 1800 hours of good service, it's time for me to replace my front tires for the first time. Having never done this before with my tractor, I'm trying to insure I get the right tires for the job. I have...

Our neighborhood tractor attachment coop (all three of us) are looking to buy a well built and reliable PTO driven digger. We've ruled out hydraulic units (one of our members does not have a third function remote and doesn't plan on installing one). So.....we'd like to hear opinions on the...

I plan on helping kjacob install a block heater unit on his 2003 TC 30. We want to do this right the first time, so if someone has already done this work on a 30, we would appreciate any friendly advice. It looks like he's got a nice clear shot at a soft plug on the left side of the engine...

Gentlemen, We've started an implement cooperative in our neighborhood, as three of us all have compact tractors in the 30-35 horsepower range with category 1 three point hitches. Our next collective purchase is a PTO driven post hole digger. None of us are going to beat the heck out of this...

My neighbor just joined the NH community with a purchase of 2003 TC30 and 7308 FEL. I've invited him to join TBN and hoped any TC30 owner out there might want to say a few things (both good and bad) about their machines and pass on some wisdom. So, if you have a story to share, or advice to...

Okay guys, Just helped my neighbor make a purchase of 2003 TC30 (only 434 hrs!!!). The little guy is in excellent shape (see pic). Question: Can I get a block heater for this machine? And if so, can you recommend a brand and model? Finally, where would attach on the block? Best to all, Jed

What might be a fair price range for a 1986 JD 950 4WD with 1921 hours? It has a FEL, a ROPS canopy, and a Bradco 8MD hoe with a 9" and 18" bucket. Weather beaten, but mechanically fine. Thanks!

Hey one and all, I'm a blue man myself, but I have a neighbor seeking a used tractor. There is an auction coming up on the 12th of June, and among the items for sale is a JD 950 (awaiting info on the year) with 1921 hours on it. As you can see in the pics attached, it has what looks to be a...

I'd appreciate member views on the DR chippers. There's an 18 hp gas DR Chipper up for sale at auction in a couple of weeks, and I'm thinking of bidding on it. DR advertising claims it's their biggest model, capable of managing 5 1/2" (although I know that's always oversold by all chippers)...

Hey guys, I have a 2004 TC35, still going strong and problem free with 1600 hours. The other day, I started and pulled away without unplugging my block heater!! Fortunately, there was no damage done, as the plug to the heater is attached to the heater itself with a detachable connection...

I have a tc35 that I bought in 2004. Love the machine, and it has not given me any problems at all. About two weeks ago, my fuel gauge started acting erratically. Previously, the gauge showed the actual fuel level consistently whether at rest or when at work. Now, when the tractor is idling...

Hey all, I'm planning on putting in some trails on my land, and clearing some abandoned pastures that have small woody (1-4 inch diameter) trees. Thought a chipper would do the job nicely for anything too small for firewood. I like the Salsco 627, made here in Connecticut. Anybody out there...

Anyone out there have a metal failure on your ATI grapple? I have the model GK-4866, and have gotten good use out of it since I bought it in fall '04. The overall strength of the unit is good, but the joint that connects the grapple claw to the hydraulic cylinder has failed. The metal just...

Most tc series owners seem to find the headlights not very useful for illuminating the work area in front of the FEL. I also like some light on either side of me when working, as well behind me for the 3pt. I didn't want to mount to the upper part of the ROPS, as I sometimes have to fold it down...

Most tc series owners seem to find the headlights not very useful for illuminating the work area in front of the FEL. I also like some light on either side of me when working, as well behind me for the 3pt. I didn't want to mount to the upper part of the ROPS, as I sometimes have to fold it...