sodamo
Super Star Member
- Joined
- May 20, 2004
- Messages
- 15,826
- Location
- Big Island, HI
- Tractor
- LS XR4140H (Mine) BX2380 (wife’s)
Happy Anniversary Mr & Mrs Happy
Good morning!!!!
- Thread starter 300UGUY
- Start date
- Views: 17282339
Happy in NC
Gold Member
- Joined
- Apr 20, 2024
- Messages
- 453
- Tractor
- 2003 New Holland TC45D
Thank you!!
Good morning,
45° and foggy now highs in the upper 70’s mix of clouds/sun winds WSW 5-10 mph today. Sun never showed up yesterday, stayed sort of misty. Any moisture is good as dry as its been.
Plans for today include leaf patrol and then some energy conservation.
Happy in NC, happy anniversary to you and your Mrs
Enjoy your day everyone
Stay safe and healthy
45° and foggy now highs in the upper 70’s mix of clouds/sun winds WSW 5-10 mph today. Sun never showed up yesterday, stayed sort of misty. Any moisture is good as dry as its been.
Plans for today include leaf patrol and then some energy conservation.
Happy in NC, happy anniversary to you and your Mrs
Enjoy your day everyone
Stay safe and healthy
mpham
Veteran Member
Morning all!
Congrats Happy!
Been working on leaf duty for the last three days. Filled the yard vac to the brim 4 or 5 times each day. Hopefully today will be the last of it for the season. need to check the rain gutters one last time also. Not much else going on around here. I like it that way! Did manage lot's of time in the shop.
Lot's of doctors appt. for her and I in November so will be busy with that. Don't want to change the clocks!! this weekend! I need light at night not in the morning. Oh well.
Off to make more coffee.
Hope everyone stays safe and healthy!
Congrats Happy!
Been working on leaf duty for the last three days. Filled the yard vac to the brim 4 or 5 times each day. Hopefully today will be the last of it for the season. need to check the rain gutters one last time also. Not much else going on around here. I like it that way! Did manage lot's of time in the shop.
Lot's of doctors appt. for her and I in November so will be busy with that. Don't want to change the clocks!! this weekend! I need light at night not in the morning. Oh well.
Off to make more coffee.
Hope everyone stays safe and healthy!
daugen
Epic Contributor
good morning all
going to be a warm day, 50 out now going up to 80 later.
have an early doc appt, errands to run, then home to wash the rv and suck up leaves on a pretty day.
Mostly, hope you get some rain
going to be a warm day, 50 out now going up to 80 later.
have an early doc appt, errands to run, then home to wash the rv and suck up leaves on a pretty day.
Mostly, hope you get some rain
Thomas
Epic Contributor
- Joined
- Apr 6, 2000
- Messages
- 31,081
- Location
- Lebanon,NH.
- Tractor
- Kubota B2650HSD w/Frontloader & CC LTX1046 & Craftman T2200 lawn mower.
No grocery shopping today Ron. 
Thomas
Epic Contributor
- Joined
- Apr 6, 2000
- Messages
- 31,081
- Location
- Lebanon,NH.
- Tractor
- Kubota B2650HSD w/Frontloader & CC LTX1046 & Craftman T2200 lawn mower.
Balmy 46F sunny day high mid 70's.
Outside chores done E muffin time.
Plans for today...8 hours at part store afterwards.
ronjhall
Super Star Member
Went yesterday. Originally was going to have breakfast with friend at 8am today. So did my shopping yesterday morning. We changed time yesterday afternoon.No grocery shopping today Ron.
Looking4new
Super Member
- Joined
- Apr 8, 2012
- Messages
- 9,885
- Location
- Northern Ontario, Canada
- Tractor
- 2012 Kioti CK27HST w/cab
Good morning, the low is 54 and going to a high of 64°F. Wind NE 2 mph. 60% chance of showers.
We got 2 of the three windows done yesterday. He did most of the work. Where he needed a third hand I was there. The 2 worst ones are 5x5', the overhead work is hard, even for 2 guys that are over 6' tall. The next window is 4x4', a little easier.
Happy Anniversary Mr. and Mrs. Happy!
I may check the block heater itself tomorrow on the Kioti to make sure it is working properly. High tomorrow is only supposed to be 39.
Have a safe day all
We got 2 of the three windows done yesterday. He did most of the work. Where he needed a third hand I was there. The 2 worst ones are 5x5', the overhead work is hard, even for 2 guys that are over 6' tall. The next window is 4x4', a little easier.
Happy Anniversary Mr. and Mrs. Happy!
I may check the block heater itself tomorrow on the Kioti to make sure it is working properly. High tomorrow is only supposed to be 39.
Have a safe day all
Popgadget
Elite Member
Good morning
45° high of 80 and clear skies. Sure doesn’t seem like a Halloween forecast.
Yesterday started with a visit to the dermatologist. Got some freezies and two biopsies.
Left that office and hopped in the little plane to meet up for the closing which went off without a hitch.
When I got home, I had grain bins to fill in the barn, got the BBQ grill moved to the new patio, helped my wife move stuff from the old kitchen, mostly appliances like a bread machine, Cuisinart, waffle iron,kitchen aid mixer, blender, knife sharpener, etc. so far it’s been easy to find a home for everything, cabinets and drawers are not full yet.
Today,I want to pickup some steel to make fireplace tools and a stand for them. Probably need to clean up in the shop so that I have space to work. The welding table, being a horizontal surface is completely cluttered with “stuff”.
I still have things to move, but I’m only moving things as I need them.
45° high of 80 and clear skies. Sure doesn’t seem like a Halloween forecast.
Yesterday started with a visit to the dermatologist. Got some freezies and two biopsies.
Left that office and hopped in the little plane to meet up for the closing which went off without a hitch.
When I got home, I had grain bins to fill in the barn, got the BBQ grill moved to the new patio, helped my wife move stuff from the old kitchen, mostly appliances like a bread machine, Cuisinart, waffle iron,kitchen aid mixer, blender, knife sharpener, etc. so far it’s been easy to find a home for everything, cabinets and drawers are not full yet.
Today,I want to pickup some steel to make fireplace tools and a stand for them. Probably need to clean up in the shop so that I have space to work. The welding table, being a horizontal surface is completely cluttered with “stuff”.
I still have things to move, but I’m only moving things as I need them.
