john deere 3038e

There seems to be an extra quick connect on the under side of the tractor Any idea what its purpose is? I cant find any reference to it in the manual

Just about ready to pull the trigger. It is a two part purchase, 1) adding two rear remotes to the 3038e 2) ordering a Frontier FL1061S (mfg by Maschio) 61" hydraulic offset flail via my local JD dealer. The attraction to this package is the ability to cut with the unit turned vertically 90...

I’m installing a 3rd function hydraulics to operate a grapple. Could someone tell me where the power port is located on a 2016 John Deere 3038e? Thank you!

Hi all, Considering a stump bucket for my JD 3038E. Cleaning up a lot of wooded areas which will have smaller tree stumps. Mostly under 10 inches down to a few inches. Any suggestions on a decent and functional but affordable stump bucket for the JD quick attach on the 3038E loader? Thanks for...

pulling up some rocks and the lower fitting on the curl cylinder's hose started spurting fluid where the hose end threads onto the hydraulic line. I someone post a picture of a damaged o-ring which they claimed to be a typical culprit. Is this a common issue when pushing the loader to the edge...

John Deere 3038E hydrostatic shift lever is broken.. is this something that can easily be fixed? the parts, the lever is about 90 shaft key is 7

I have a 3038e I bought new 2017 with 406 hours. It runs great. D160 FEL, 9.5 ft BH, 10 attachments. The problem is lift capacity. I just got new 350# forks and wanted to remove a 4x4x8ft hay bundle (about 1,100#) off of truck into horse stable. I've been unloading bales no problem, but I'm 70...

Anything to look at in particular about this tractor and FEL with 300 hours? I have a hst 4100 with FEL. I'd like more HP to run the tiller, etc. What price should I expect? Any major issues to look out for?

Hello I have a John deer 3038e and it's has white some when running when giving fuel or under load lots of white smoke any ideas what to check Thanks Mike Henry

I have a 3038e with lots of attachments. Today I'm working on an area I'm putting in a horse riding ring. It's on a slope so I'll take about 5ft down high end, putting on low end. It will be about 120ft X 60ft, oval, posts, boards, 1 or 2 gates. It's full of scrub trees so I use front end loader...

I have a Napa much closer than dealer. They couldn’t tell me what battery I need (I don’t have the old battery - tractor has been stored without battery for years. Trying to get it started again to bring in for maintenance work). Reading here I saw a 51R 500. Is this correct? Thanks.

My 2012 3038e appears to have a solid flat disk as the outermost seal on the rear axle. It has loosened and seems to expose an inner seal. There is no leaking of hydraulic fluid or anything. The part appears to be a single flat washer-like piece with no threads anywhere and, I guess, should...

The seat on the 2010 3038e was getting past due for replacement. There was a split in the cushion, the cushion was separating from the metal pan, and the metal pan had more rust than paint. Seats for the 3038e have changed over time. My seat used sheet metal tabs for mounting to the seat base...

New tractor owner here. I have a 3038e that I bought new last year and am wondering that the coupler in the photo is used for. I could not find any reference in it in the manual. The coupler is located underneath on the right rear side of the tractor. Thanks

Wondering if anyone else has had issues with the short hydraulic hose that runs from the rod end of the tilt cylinder to the supply hardline coming loose when tilting the bucket. I have re-tightened numerous times, wrecked a couple o-rings, and tried loc-tite but am still unable to get the union...

I'd like to order weights for my tractor. There's a front bracket 9"×4"×1/4" that I assume is for weights, but it's only 7" wide inside bolt to bolt. There is a bracket I can order for 10 weights LVB24952, but it's about $200. Weights from what I see are 42, 70 & 100#. 42's are UC13263 part #...

the pto on my 3038e will not engage. I have replaced the pto switch and the solenoid. Any help or ideas is appreciated.

I recently split my 3038e to repair o ring on the 4 wheel drive linkage, all went well, tractor went back together without issue. When i started the motor there was a pop and the PTO oil supply to the PTO clutch broke. Has anyone had this issue, i discussed with the local dealer and he had no...

Replaced the battery in the 2010 3038e again today (wouldn't start without a boost). The original lasted about 5 years, the NAPA that replaced it made 71 mos. so I went with the 7551R from NAPA again. It was also about $40 cheaper than the JD battery (per web site pricing). Fingers crossed it...

I was mowing today & noticed the PTO indicator light on the instrument panel was no longer lit even though the rotary cutter was still cutting. It had been illuminated when I first engaged it. Disengaging/re-engaging the PTO worked fine but had no effect on the light (it stayed out). Are...

It finally happened i got one **** of a deal on an EZ guide plus and a steering motor $250CDN!!! So naturally i am going to put in on my compact tractor, I have a few pics of the install. Not for the faint of heart........ It was not really meant to install on this small a tractor. The first...

Finally got all the parts together to use some worklight mounts I made a while back for the 1025R & 3038e on the 3d printer. They were done in a semi flexible version of TPU, a material that lets you produce parts whose feel is very similar to tire rubber. These are the mounts done for the...

2015 3038E where is the serial number? Want an operating manual and want the right one. Thanks,Mike

My John Deere 3038e hydraulic oil was in the middle of the dip stick, so I decided I'd add a little Champion 4000 hydraulic oil (j20c compatible) to bring it up a little. Tractor has 175 hours on it, so assume it hasn't been changed ever, or since 50 hour checkup. Did I do a bad thing mixing JD...

Hello, I replaced the factory battery in my 3038e with another battery that has 650 cca. When I turn the ignition I get the clicking sound (it does sound faster and louder) then when I turn the key to start nothing happens, does not start. Any one know what is happening that it will not start...

I have a John Deere 3038e that I am need a wiring diagram for. In specific the pin break down for the instrument cluster. I am trying to find where each wire goes to. I can't seem to find this information any where. Thanks in advance for the help.

Considering a 3038E. Im fairly aware of a lot of the cost cutting with the tractor. I dont need a mid PTO because I have a Z915E for mowing. Id be doing mainly brush hogging and box blading. FEL stuff too. Def would want to add a 3rd function for a grapple. One thing though, Ive been told you...

Hey guys, Friend of mine has a new 3038e (2018 I think). Anyway, it appears as though the only PTO controller available is the electric rocker switch on the right fender panel. Is there another manual lever that will disengage the spline on the PTO completely, allowing it to rotate freely if...

Friend of mine is considering a new JD 3038E tractor with FEL. Does Deere still require Blue Def diesel additive for exhaust regeneration? Thanx!

My rear seal for the driveshaft for the front wheel drive is leaking. I guess a stick pushed it in because the bottom is in 3/8in too far. Has anyone replaced one of these? It looks like it is installed from the outside but I'm not sure how to disconnect the driveshaft. It has a joint about 4 in...

I have a 2009 JD 3038e and for a while now the forward pedal won't go in.. it feels like its under pressure sort of, i can squeeze it in a little and its enough to drive forward but at a slow rate compared to the way it should. The rear pedal is freely moving and working as is. I check the...

Curious if anyone knew best place to get suitcase weights for my John Deere 3038. How many can I put on it, best price, etc. Thanks. I'm in process of pulling up old fence posts, it works great with 3pt. Lift of fel and chain, but pulling up a large grapevine by the roots lifted tractor way up!

I'm having an issue with my 3038e and its driving me crazy. For some reason I posted under the general folder so I thought I would share a link here in case any Deere guru's only sit in here and not venture out to other areas of the forum lol...

I parked my deere after a mow and a few days later went to crank her up and nothing and I cannot figure out what the issue is. :pullinghair: PTO button is down, in Neutral, and parking brake up, and sitting on seat.. instrument panel only has the lower right icon lit up.. which is the engine oil...

About to jump into the compact tractor world. I have 30 acres, planning on using a tractor for bush hogging, and land clearing, tree work. I have a great local JD dealership within 5 miles that has served me well for other purchases in the past. I have found a lightly used, under 100 hours...

Hi everyone, Im new to this forum I own a 2015 John Deere 3038e that has a 3 pt issue. Currently I bought the tractor knowing that the 3 pt wouldnt go up or down figured a simple fix....Right.... I can in fact grab the lift arms and move them by hand up and down by hand. Almost feels like I...

We have just signed up on this forum. I have been reading some posts from this site concerning JD 3038E questions and seemed interesting so I signed us up. Looking forward to some good info!

I am new to the forum and new to tractors.... I am currently looking into getting my first tractor, a John Deere 3038e new from the local dealer. The one thing I can not get over is the fact that they only have 2017s that have been sitting on the lot for almost a year and they will not budge on...

I noticed that my rockshaft control lever has gotten harder to move forward/back. JD dealer mentioned I should look at the Rate of Drop valve to see if it needs adjusting (his fear was that there was too much pressure build up in the hydraulics). First question is: could it be hydraulic...

I have searched everywhere for some information and have not found anything. So I am looking for some help. I recently parked my tractor on the side yard on a slight hill without setting the parking brake. This was mainly because I was being chased by ground Yellow Jackets, so my judgment might...

Here's a good one for you! I borrowed my father in laws 3038e to repair some stump grinder remains and it was parked outdoors overnight and it rained. The next morning, I proceeded to do my work and I noticed standing water in the "moat" around the fuel tank filler cap. I figured some debris...

I've got a quote in hand for the following package and would like some feedback from those that have purchased before: JD 3038E w/R4 tires JD D160 w/hood guard Frontier RD2060 w/slip clutch and front/rear chain enclosed Frontier BB2060 Std Duty Box Blade Package delivered to home. Total $23K...

I recently purchased a new 3038E and just noticed it does not display vehicle speed or mph. The manual doesn't cover speedometer and I have called the dealer and John Deere with no luck. I am told the 3038R has a speedometer. How are you to apply fertilizer and use a sprayer without ground...

Had a massive hydraulic fluid dump last week. Started the tractor to move snow in 5 degree temps. Did a few odds and ends waiting for the tractor to warm up. When I came back to it, it was dumping the last of the hydraulic on the ground. Leak was a blown-out gasket at the high pressure hydraulic...

Just got this tractor. Had Yanmar 2500 I used to move around wood stacked on pallets. The fel on Deere won't pick up same pallets. Can it safely be turn up? Any and all advice would be appreciated.

This is my first winter with my new to me 3038e, the owners manual says to put the range lever in low and turn the key to start position for X seconds, then move the lever to neutral and let it start. It does not say what is going on in the machine. Does this activate an internal heater? All...

Hello all, Enthusiastic newbie with a 2012 3038e that is absolutely amazing. I'm using it to clear a future homestead and its perfect for removing saplings and grading the washboard effect out from under reforested pines. I have a fantastic dealer that sold it to me, too. Just one annoyance...

I have a 2014 John Deere 3038E Tractor and drove it with the dipstick removed. I was not aware of this until it ran out of oil and stopped . I turned it on very briefly and it sounded like two steel poles banging together. Is this tractor engine repairable? Arnold

Hey guys looking for a cost effective way to add a couple remotes to the rear of the tractor primarily for a hyd. top link. Is it possible to do it just with hyd. hose and a 2 spool valve? Know there is a kit avail. from deere but think its priced to high for what I want to accomplish. Any...

One of those days where what can go wrong does... Was bush-hogging the acreage yesterday, managed to lose the fuel level indicator when opening the hood to deal with a dust related over-heat, noticed earlier that the pond overflow pipe was clogged & water about 2' too high and then, while...

Hopefully someone on the forum has seen this before and can offer a suggestion... Got a 2015 Deere 3038e with a D160 loader, with about 45 hours on it so far. I had several acres of land logged-off over this past winter, and I am moving the cuttings and brush into piles for burning. I was...

Guy's First of all thanks in advance for you answers. I removed the battery cables, and then tried to remove the battery hold down bolt/clip combo. The bolts turn freely but do not back out so I can remove the hold down clips. Are there some hidden nuts or what am I doing wrong. All help is...

Hello all! Looking at a John Deere 3032e or 3038e. Just the right size and plenty simple. The problem is that all the reviews mention that you cannot take the loader off. Then I found out that the loader is often installed at the dealer level. If the dealer can bolt it on, a person should be...

I have a John Deere 3038E that is about 6 years old, 400 hrs. The loader works fine. The problem is with the hitch. As I adjust the rockshaft lever from the 1 position to a higher number, nothing happens until I reach about 6. The hitch then raises all the way up, unless I pull back on the lever...

I have a John Deere 3038E that is about 6 years old, 400 hrs. The loader works fine. The problem is with the hitch. As I adjust the rockshaft lever from the 1 position to a higher number, nothing happens until I reach about 6. The hitch then raises all the way up, unless I pull back on the lever...

The tach on my 3038E has stopped working reliably. More than half the time when I start the tractor, the tachometer will indicate 0 RPMs. After some time (as little as a minute to as long as an hour) it will start working. And once it starts working, it will continue to work until I shut the...

I recently added some LED work lights to the 2010 3038e. The first added were some fender mounted 6 element floods (18w). I had previously installed a couple of side mirrors originally intended for use on ATV roll bars. To clamp them on the grab handles, I had drilled new holes & formed them...

Came by here looking for some PTO help. Decided to sit a spell... :D

Hey There, Newbie on board tonight. I live in Central Florida and just purchased a 3 acre lot with home. About 2.25acres available to farm. I worked on the family farm growing up and now am going to revisit the joys of dirt on my hands. Our plans are to raise cows, goat, chickens and large...

Which one is the better tractor L3901 or JD3030E? I am buying a new tractor that will mainly be used for mowing, moving some downed trees for firewood, and some trail / road management on 16 acres. It is mostly wooded, but I have 5 acres of rolling open land that is being turned back to pine...

Hello - new to the forum and, frankly, signed up to ask for help. I have a JD 3038E with less than 100 hours on it and I just noticed an oil leak. It appears to be coming from the seal around the driveline heading to the front axel. Does anyone have any experience with this that can point me in...

Hey, Fellers, Couple things about the 3038e I just bought. First, the photo shows the concrete ballast block I fabbed up. It turned out nice, but it's too heavy. I got the AF11 hydraulic-angled front blade for pushing snow. I believe the blade's 780# and it projects a ways beyond the loader...

One of my friends bought a 3038E today and was curious if anyone has a backhoe on theirs? Thanks, Sammy

Anybody know of a good hydraulic damped replacement seat for these things?? The one that came on my tractor would be OK on my riding lawn mower but it's not up to providing any level of comfort while mowing my rough pasture. Leaning to the same Grammer seat that I put on my Yanmar. It will...

We're looking to replace our older International 240. Its been a good tractor but as its not very common replacing parts is always an issue. We have just over 50 acres of country property at our weekend place. The property is hilly but the area we mow is mostly flat.. except for one area which...

Fresh off the lot 3038e. From all indications in the owner's manual there should be a speedomter on this thing. Anybody know for certain if it's a. not available. b. optional c. not working. I'd call the dealer but the salesman told me it didn't have a turbo so I'm not gonna start with him...

My 2011 3038 won't hold bucket in curl. If I don't bump it up every 100yds it dumps. I had a 790 that did the same thing and was one of the reasons (although the hydrostat and hp were the main ones) that I traded. Any idea what would cause this problem? Thanks.

Ok well I have read most of the starting problem posts about 3038e. I have an issue that just started. My jd won't start I have checked the battery at the auto parts store, I have made sure I have 13.1 volts everywhere. Checked all fuses and relays. Jumped the start safety switch and seat switch...

Hello everyone. I have a 3038e and the left front axle is leaking where it pivots. I assume there is a seal there that needs to be replaced and wanted to see if anyone had any pointers as to what seal is needed and what is involved in replacing it? Thank you in advance for any help. (picture...

Just purchased a JD3038e at my local dealer yesterday. Should be ready to pick-up by the 16th (Thursday). Curious to hear from existing model owners likes and gripes on this model. Thank you in advance.... Mark in Central Virginia

Looking for some insight on 2002 Kubota L4310 versus 2012 John Deere 3038e versus JD 4410. All have loaders with 4x4 and HST. All are from private sellers. All say they've been serviced and not been worked too hard. All seem in similarly good shape with about 75% of tire wear remaining...

Hi, First time poster on this board. Previous searches have yielded a lot of helpful information as I try to nail down the right tractor, so thanks already for the great insights. I am looking to purchase my first tractor. We just purchased 10 acres of vacant land that we are turning into a...

Howdy, I currently have a Deere 3038E and would appreciate replacement suggestions. It has been a great little tractor I have just outgrown it's capabilities mostly on the loader side. My two biggest issues are the ride, and the loader size/capacity. It has been suggested to fill the rear...

I am building a cab for my 2014 John Deere 3038E. I plan to use canvas doors with clear plastic for see through windows. I had a JD 750 with this type of cab and it worked fine to keep the wind off when plowing snow. I will attach pictures as I go along. I am using 1X1 square tubing for the...

Hi guys. First time poster. I am in the market for my first tractor. I've narrowed my decision to 3 models. The 2032r, 3032e or the 3038e. Looking at the numbers, I can't see the advantage of one over the other. I don't need or expect that I'll ever need a Mid-PTO. And it's unlikely that I'd...

Just joining the site to ask question and find info on my 2013 John Deere 3038E

How many foot pounds of torque does it take to put on the rear wheels of a 2013 John deere 3038E tractor

I have built a FEL mounted plow using an old fisher snow plow that I cut down. Ideally I would like it to be power angle. Is it possible to connect the plow cylinders to the roll function of my FEL? One cylinder to the end of the roll circuit and the other cylinder to the end of the curl...

Stopped yesterday and got a quote for a tractor and some eq. Is this in line with your area?

I got a quote from a local dealer on a 3038E with the loader for $25899 plus Gst. 60 months 0% any one know if this is the going rate in Canada they wont negotiate one cent on price. Ike

My JD 3038E with 144 hrs has developed an annoying issue. It starts immediately runs for about five seconds then shuts down. After cranking for about thirty seconds it will start again then repeat the symptoms. After the third or fourth time it will run fine the rest of the day until I shut...

My 2008 3038e decided it wanted a new battery :laughing: so I stopped by the tractor shop while in town and they didn't have the TY26498 in stock and would have to order it. Now I'm wondering is there a good replacement for this JD battery that I can pick up from TSC, Walmart or even Battery...

What is the largest disc harrow.. box blade would you use with this tractor? thanks

3038e pto will not disengage, runs all the time. tractor will crank and start and pto will come on as soon as engine starts with pto switch in off position. safety switch on seat will work when pto switch pulled on and pto light on instrument panel will go off and on with switch position...

I know the comparisons get done to death, so please bear with me. Upon pricing, I have been shocked to find the JDs are less expensive. With that said, I can buy a JD 3038E for $1300 LESS than a Kubota L3200. I have seen the comparisons between 3032 and L3200, and 3038 and L3800, but in this...

Here is My dilemma I have been looking and comparing and have come to a a tough choice. I can get a Mahindra 3016 with FEL and finish mower for 19,516 out the door OR I could get JD 3038 with FEL, finish mower and box blade and tires filled and delivered 20,375 out the door. Facts: Mahindra has...

Well, here it is. I have been reviewing these 2 tractors for a steady 2 weeks now and am really no closer to a decision on which tractor to get. Any advise would be greatly appreciated! I have a 10 acre residence that I have about 5 acres in horse pasture. I will use the tractor for a...

Looking at a 3038e and the tires look very tall for how narrow it is. Tires already appear to be heavily offset so I guess flipping is out of question? Has anyone tried a spacer or widening kit? or would that be too much stress on axle shaft/seals?

We have a JD 3038E we purchased new three years ago that has been operating fine until about 4 weeks ago when we the mower deck. We can adjust all the way up but if we park the lever anywhere but full up the hitch arms lower all the way down. Any one had this or similar problem? we checked fluid...

Hello all, it's been a while since I posted. I have been a pretty busy boy for the last year or so. I have a 3038E JD and was having a problem a while back with the Calcium Chloride liquid filled rear tire on my machine and I posted about it here on TBN. Well , now I am having the same problem...

Thirty eight hp sounds like alot of zip for a small frame tractor. Just saw an ad for one. It said prices start at 16k for the E series. They still continue with the two speed hydro. Three speed should be minimum.

Anyone with experience know if this tractor has a magnetic hydraulic screen? I serviced my hydraulic oil and all I could see was a normal drain plug with no screen anywhere to be found. I called the dealer and they said, "we do not think it has one"....so I could not get a straight answer out...

My 3038E has about 100 hours. Hooked up my post hole auger Sunday, but could not get PTO to engage. I've used it many times before, along with my shredder with no problems. Knob engages OK, dash light turns on, but no drive action at the PTO shaft. Seat safety switch works. Tried in neutral, in...

I haven't been able to find a locking cap for a JD 3038E. I find caps for larger JDs but not 1000 - 4000 series.

How do the 3032E and 3038E tractors cope with moving and loading round bales? The specs look like it could be touch and go. Does anyone use their machines for handling round bales?

Hello all, I am getting ready to change the oil for the first time on my JD 3038e and wanted to know if any of you recommend an oil and or filter alternative for this machine. I do not have a dealer here in town and if possible want to save a few bucks. Any help is appreciated.

Running over some slash, I nearly sheared the positive battery cable that runs under the chassis near the front of my 3038E. I'm new to tractoring and apparently need to be more careful. Maintainability is one of the main reasons I bought a Deere; it's nice to know parts are readily available...

I am a first-time tractor owner with a JD 3038E. I would like to add attachments that require hydraulics. I have no experience with hydraulics, so I would like to start with the JD rear hydraulics kit because it's designed to fit my tractor without any hassles or hydraulics design knowledge on...

It's come down to this. My local dealer is finally offering an acceptable deal, but only on 3032E machines and 3038E. Originally I thought these were great for the money, but I started researching Kubota and it seems maybe they offer a lot more tractor in comparison to JD. I want to pull the...

Quick question: What is the lift height range of the 3 point linkage on the 3023E and 3038E tractors. I can find capacity, but not lift height. I'm wondering if I can lift a round bale of hay into my trailer, which has a deck height of 500mm. Thanks.

I recently purchased a new John Deere 3038e and I love it. I spent a lot of time reading reviews and information all over the internet and mainly on this website. I visited the local dealerships and drove different equipment before I made my decision. Overall I spent close to a year looking...

I am looking at the John Deere 3038E to work my 5 acre horse farm. Tasks will include loader work, mowing and plowing a horse arena. I understand that these tractors are fairly light so weight will need to be added. My question is will this tractor pull a 5 or 6 ft tandem with it put in the...

Will a 3038 the handle snow removal on a 1200 foot drivewaywith using a front blade attachment, weekly mowing 5 steep acres, and annual tilling 5 food plot acres with a rototiller and still last for many years or is this work load too much for this tractor. Please advise. Thank you.

A local dealer gave me an almost new suspension base from a large Kubota. I removed the JD 3038E seat and base matched it up to the new base and marked 4 holes to drill. I installed the new base with the original bolts. I cut down two 5" angle brackets, drilled 4 holes, and bolted them to the...

I just ordered a new John Deere 3038e. I had the extra SCV added, but my understanding is they will not allow me to run a continuous flow to a three point wood splitter. This model does not have a power beyond kit. Is there a way to make this work, or do I need to by a pump for the PTO...

All - I am a newbie to this whole tractor thing and am learning a whole lot from this website. I have done research regarding the issue of ballast and have read just about every thread that has to do with filling the tires, rear wheel weights, and ballast boxes. Unfortunately, I am still...

81 hours on 3038e and throttle started losing it's rev unless I keep my hand on it. Any help is appreciated.

Anyone have experience with installing a winch on a JD 3038e? It's just purchased and the dealer had had no experience with it.

All, I have done a search but yielded no satisfying results thus far. As an owner of a new 3038e I can tell you I could not be happier. One little thing though has been weighing on my mind and thought I would ask around. At idle RPMs, my PTO, when engaged, makes a pretty loud (unsettling)...

I know it's not apples to apples, but... I currently own a 2305 (almost four years now) and have used it on our 1.5 acre place in the San Diego area. I haul manure (we have three horses), move hay around, dig postholes, light grading, etc. I also have a tiller attachment (that my neighbor...

Although I really need a larger tractor, I keep coming back to the 3032E due to price and small size (we have some tight areas between pens that a larger tractor may have some issues getting around). Due to the low weight of the 3032E, I would probably be able to take it more often to my other...

Decisions Decisions...Ive narrowed my choices down to either Kubota L3200 or the L3800 AND the JD3038E..... here is my current debate....Is the L3200 a better choice than the JD3038E....both are very similar in price. I know the Deere has more HP. But.....how does it compare overall? any...

Finally came up with a cheap, easy solution for tool storage. Hung a discarded day pack/book bag on the rear light fixture by crisscrossing the shoulder straps. Lots of room, easy access, and the small exterior pockets are handy for little odds-and-ends. Thought I'd also show off my carryall...

As the title suggests, I need some help. After hours of researching and a couple sleepless nights I have decided to go with the 2012 John Deere 3038e. From my own research and after looking at dealers across the country, it looks like $17900 is a reasonable price to try and get the dealer down...

The fellow who delivered my new JD 3038E with ag tires indicated I could flip the front tires side-for-side to gain width and stability. He said he had done it easily on his 32E. The manual seems to call this the "wide setting" and allows if for uses other than FEL. Since I frequently use my...

I'm trading in my good ole 1974 JD 2030 for a compact tractor. I've looked at other makes, but decided to stick with JD for a host of reasons - dealer relationship among them. I'm looking at a 3038E vs 3320. I like the 3320 for its weight, although it has less HP. And it's substantially...

I'm looking to buy a JD 3038E. Trying to find some of the pros and cons. Will mostly be mowing about 8 acres of grass fields with some brush.

Built a grapple for my 3038e this summer. Again got alot of ideas from members on this forum.I believe one of the members was 3RRL. Unable to find the thread though. It works great! If I did it again I would have installed toothbar and designed grapple reach to end of teeth though. Was...

After freezing my butt off last winter and reading huskerplowboys thread on his cab build. I thought a cab would be a good challenge. This cab will definitely not be as high quality as his though. Started mockup of cab out of wood.

I have been reading and learning a lot from all these posts and have decided to ask you all to add your two cents. (I love that phrase because it seems like you are undervaluing your experience and opinions!) There was a recent post comparing the Kubota 3800 and the JD3038E and questioning the...

Hi everybody.I was on the way to work the other day and had to stop in and get gas .While i was filling up a truck had pulled up to the pump next to me and had a 3038e on a trailer.So i asked him how he liked it .He responed that it was not his and it was the company he works for. But he did...

I am getting ready to purchase a new tractor for my small farm. I will mainly be using the tractor for grading driveway, moving manure, and bushogging. My property is very hilly. I have priced the both of the above tractors. Both tractors have the Hydrostat Drives and both dealers are going to...

Does anyone know the model and specs. of the valve wr long uses in their third function kit for a JD 3038e with a 305 fel ?

Does anyone know the model and specs. for the valve wr long uses in their third function kit for a JD 3038e with a 305 fel ?

Has anyone with a JD 3038E bought wheel spacers and how have they worked out for you? Also what company did you purchase them from? Thank you for any help on this question, with out the spacers it makes me a little nervous on slopes. Thanks, FarmallFan

Hey guys, I need some opinions on the John Deere 3032E and 3038E tractors. I am considering one of these model tractors. It will be used for brush hogging w/ a 5' mower, boxblading a long drive, and general loader work. I would like a grapple in the future. My main concern with this machine...

While pushing a couple of tree limbs into the edge of the woods something went "pop". I stopped and started backing up and something didn't feel "right". I looked down and the right front wheel was turned 90 degrees to the right. The whole wheel assembly had come loose and "fallen" from the...

Greetings, I am looking for rear wheel weights for a 3038E with the R4 tires. Just wondering if any other owners have found wheel weights to fit this tire/rim. Thanks in advance. Troy

I'm looking at purchasing a 3038E and was wondering if there are any aftermarket backhoes that can attach to it using a sub-frame? I didn't see where the Woods sub-frame was compatible but are there any others? Thanks.

I have purchased 33 acres of mesquite and dry dirt that I am planning to homestead. Small scale farming if you will. I'll have a garden and some animals and probably plant a little hay. I do not plan on baling it as there are several local guys who have large balers. I am using my dad's...

A similar thread was posted in Buying & Pricing forum, but I thought I should post in the owning/operating. Sorry, if i should have continued with that same thread. Anyway, I purchased a JD 3038E in Dec '08 (my first EVER tractor). I currently have less than 100 hours on it, but I've recently...

Can someone tell me where I can find a value for a JD 3038E? Is there a blue book that I can access without having to pay? Or, can someone tell me what would be a good buying price for a 2010 model with about 50 hrs? Thanks.

Folks, I bought a 3038E with RC2072 cutter last summer for my 100 acres and thought I would give report on my experience FWIW to those thinking of buying this tractor. The machine only has 40 hours on it, since bushhogging is all I use it for. I did have a warranty repair when the...

I stopped in the local dealer yesterday. They have a 3038E smack beside the front door- hard to miss! They quoted me $17,600 on it, R4's and FEL. That's a good bit less than the on-line prices of JD and an L3800 Kubota ($21,670)

I screwed up big time last fall and bought a new JD 3038E with the industrial tire option. I've since started a sportsfield and turf renovation business and the industrial tires are unacceptable. They were a $240 option when I bought the tractor and now they will cost me about $2000! I believe...

Does anyone know of a company that sells wheel spacers for the 3038e? I checked with my local JD dealer and JD doesn't have spacers. If anyone has used the spacers how did you like them? I would like a little more stability. Thanks for your help, FarmallFan

I have a John Deere 3038e and I would like to move the rear tires out some to give me more stability. My local dealer checked and John Deere doesn't have spacer kits, but a while back I saw a thread where someone had installed spacers. Is there a company that sells spacer kits? Has anyone used...

Here is the best cab option I have been able to find for the 3032e & 3038e. It looks pretty good but it is expensive (well over 3 Grand US). I thought I would post this up here in case anyone would be interested. The following are detailed pdf files of the sales flyer and installation...

trying to decide between a 3032e and a 3038e price difference is around a $1000.00 more hp is nice but not having a turbo (3032e) is also a good thing. How is the torque on both of the tractors what are the real world differances Randy

Hi all. I'm the proud owner of a new 3038E. I took delivery of it last Saturday and have nearly 6 hours on it. So far I have been very satisfied. I have a quick question about the rear SCV. Does anyone know the flow rate to those hookups? I'm looking at building a log splitter and am...

You guys are the best. I have learned so much from your posts. Thank you. My tractor was delivered yesterday evening. Today was my first opportunity to do something with it. I had been wanting to put in a culvert across a small ditch, and I had some discarded culvert left by the previous owner...

While tractor shopping, the wife saw the compact Gator and just had to have one. She's planning on using it for yardwork, the 2/3 mile round trip to the mailbox & carting her mother around the farm... Notice what is being garage kept while the beloved AWD Magnum RT sits outside in the cold...

Well, she has 220 hours on her now and all is still well. I'm amazed at how far these CUTs have come when I get off my old JD750 with it's tiny cramped operator station and climb aboard the 3038e. Mods: 1) I took Kennyd's advice and bought an iMatch-style quick hitch (Harbor Freight) and...

is it worth the money to install the rear remotes on the back of the tractor? and how much would they cost anybody?

As the cleanup continues, I'm finding more locations where I can't just drive over & through. The problem with backing the cutter over the material is because, literally, looking over my shoulder is a pain in the neck. After having 3 vertebra (C5-C6-C7) fused, I can't even get my chin close to...

Just delivered today! 2010 3038E w/305 FEL, a Frontier RC2060 5' rotary cutter, and a Frontier BB2060 5' box blade. Primary use (at least initially) is to try to bring some (about 10 acres) neglected pasture back into productive use, & clean up routes through another 10 acres of wood lot...

We just pulled the trigger on a package deal today. A 3038E w/305 FEL, a Frontier RC2060 for $19,940 w/ 60 mo. 0% financing w/10% down. Breakdown of pricing was $17,500 for the 3038E w/ FEL, $1650 for the 5' Rotary Cutter & $790 for the 5' Boxblade. We were budgetting for about $20K, so...

Hi all. I'm looking at buying my first tractor and have it narrowed down to a few. All roughly 35HP. Any suggestions on Deere 3038e vs Bobcat Ct235 vs MF 1635?? My use is mostly as a wooded landowner who will be doing some light woods clearing, mowing trails, moving rocks and wood, road...

Hi all. I'm looking at buying my first tractor and have it narrowed down to a few. All roughly 35HP. Any suggestions on Deere 3038e vs Bobcat Ct235 vs MF 1635?? My use is mostly as a wooded landowner who will be doing some light woods clearing, mowing trails, moving rocks and wood, road...

I am looking at the john deere 3032e and the 3038e tractors Also thinking about the bobcat ct235. My questions about the john deeres are how much to get the cruise control and can you set any speed with it or just full speed for the range you are in? how usable is the two range hydro drive...

I have 10 acres near Bertram Tx. It was all trees when I started clearing, most of them cedar. I knocked down around 5 acres of the cedar and now I am needing something to clean up this area. We have been cutting up trees and burning and it is back breaking work. Would the 3038e be big enough to...

Have been checking out these models and can't figure out a couple of options on them... hoping someone can help: 1. I believe they're identical in size, including tire dimensions. Correct? 2. Can you get power beyond? i.e. to run a log splitter? 3. The brochure states it can take a front...

The dealer delivered my 3038E with the 305 loader and 5' JD rear finish mower. I've had it a week and have a little over 6 hours on it. Only about 2 hours was using the loader. This is my first tractor so this is a new experience. It was taking 5 hours to mow my 5 acres with a 54" riding...

I've been mostly lurking on this site, reading the tractor comparisons every day, and posting only a few times. I've looked at Bob Cat, Kubota L2800, Mahindra 2816, and JD 3032 and 3038E. My oldest son was a tractor mechanic for 17 years before getting a layoff 2 years ago. He's mostly...

I have priced out a John Deere 3038e with a FEL for $16300 total out the door.Can I buy a better tractor for that money or maybe a little more?I have looked at the Kubota L3400 with a FEl and without the Hydrostat trans. for $17500 total.Not sure if I would miss the Hydro ..never had it...

I am a relatively new owner. I had planed to wait till this spring to purchase my tractor but the hard winter forced me to get it earlier so I could clear the drive with the front loader. I am loving having a tractor, I would venture to say it is the best investment of my life. I am looking...

I am going to buy a new tractor in the next day or so. My research came down to two models the 3032E or 3038E. Both are very similar. --- Same Weight, same loader lift capacity, same transmission. Just: Why is the 3038E stronger with a SMALLER engine (1.5L) than the 3032E with 1.64L while both...

Good afternoon, I just purchased a new john deere 3038e to replace my smaller 2210. The sales guy at the dealership is telling me that the 3038e doesnt support the I-match auto quick attachment system. Has anyone encountered this? Not sure why he would say it supports the I-match and not the...

I called my dealer yesterday and considered trading my 2004Hydro 4210 with 193 hours for a new 3038 E but my salesman told me that the 4210 was more tractor than the 3038E. He said that it weighed 900 pounds less and that the 3038 is cheaper made. Less metal less machine. I looked up the specs...

Well when the ford 861 went to leaking coolant, I decided it was finally time to get the john deere i had my eye on. Since several others before me have purchased one, at least I can get the inside scoop before something goes wrong, Hopefully!!! Not saying I won't do something stupid because I...

The 3030e comes with a top link that has a large nut that allows you to tighten it to keep the top link from changing lengths all by itself, however, my King Kutter tiller shakes, rattles, rolls and vibrates so much that it's almost impossible to tighten the top link nut enough to keep it from...

I planned to perform the first hydraulic oil change at 100 hours, however, the manual says to change it every 400 hours. It says nothing about the "first" hydraulic change being sooner than that. Would changing the hyd. oil at 100 hours be overkill or cheap insurance?

I just got done adding a Prince 2 spool with power beyond and a WR Long 3rd function valve to my little John Deere 3038e. Here are a few pictures.

Just finished it up. I build 2 altogether, one for the skidsteer and one for my little tractor. Ended up with around 40 hours in the first one and about 10 in the second.

I would like to add a true 3rd function to my loader on my John Deere 3038e to power a grapple. http://https://www.surpluscenter.com/item.asp?UID=2009100416391860&item=9-6136&catname=hydraulic This is the valve I would like to use alond with the correct open center subplate. My question is...

Just bought a john deere 3038E, and was wondering if I can add a hydraulic diverter to it, or a hydraulic coupler for a set of valves at the back of the tractor (ideally 2 sets if possible!). I want to be able to rotate the chute on a snowblower, and possibly the deflector as well if possible...

Did you know that there's no way to operate a PTO attachment if you get off of the seat on this tractor? It states that in the owner's manual and was confirmed by the dealer, too. Oh, well... no PTO woodchipper for me! Picasa Web Albums - Dennis - Tractor Dennis

Hello everyone! In the market for a new tractor and have quotes for both tractors w/fel, with the Kubota being $300 more. I like the looks of both machines, and would like some opinions (other than the dealer's) on them. Some of the pros for the JD is that it is hst, and the overall finish...

Spent 20 hours in the seat the last three days doing everything from bush hogging and tilling to making the bullet stop at the end of the rifle range bigger with the FEL. The Caroni flail performed flawlessly. I took out some trees that were technically too big (some up to three inches) for...

what are the differences, both are 37hp? I have a price of $13,800 on 3038E, hyst, 4wd, is this a good price? Which one of these tractors is better? i will be finish mowing 4 acres, probably bushogging 2 acres, and tilling/plowing about a 2 acre garden.. Thanks in advance for the help.

Well after a month wait, my new tractor finally arrived. I put a couple hours on it this evening just messing around. I really like it so far. I intend to use it landscaping my property, tilling my garden, some mowing, & snow removal. Here are some of my preliminary observations...

Mowed about five acres with the Caroni this evening. Only about thirty more to go!!! :eek:

This is a great site! I've been lurking for a couple months - trying to find out everything I could to make a good purchase decision. Finally pulled the trigger on a new JD 3038e. I've got 3+ acres & need to do landscaping, tilling, & snow removal. I looked at all of the 2000 series & almost...

The 3038e has an electrically & hydraulically operated PTO that has an internal braking system. It's either on (spinning) or it's off (locked) which makes it a real PITA when trying to hook a PTO shaft to the tractor because you can't spin the PTO shaft coming out the back of the tractor by hand...

Anyone own or now anyone who own's the new JD 3038e. We looked at one over the weekend. Have 13 acres to bushhog and need to lift haybales. The tractor looks so small as compared to the old massey 135 and 175 we currently have. Need something easy to operate. Husband had knee replacement 10...

I have a question for all the brilliant minds here.. I bought a 3038e last week and this Friday I was getting familiar with it doing some brush clearing/mowing with my rhino 160 and when I got off to switch out to the armstrong box blade I noticed one of the chains was missing. Now, this was a...

i have narrowed it down to these two tractors. i was wondering what people thought about either one. also your like and dislikes. i was primarly going to use it in my landscaping company and to do bush hog.

The factory drawbar on the 3038E is so low to the ground that it's practically impossible to attach a standard trailer because the trailer-jack wont lower a trailer low enough to attach to the drawbar. The solution I came up with is a little rough but I needed it right NOW. I took a TPH...

Had a sand company dump 22 tons of dirt Friday so that I could fill in and level the deep ruts that have formed in my driveway over the last couple decades that cause any low-slung vehicle to scrape it's undercarriage. Moving and leveling the dirt with the FEL was a piece-o-cake. I had moved...

Performed the first "work" with the tractor today instead of just joyriding. Spent an hour doing FEL work. In a word.... AWESOME!!! You folks that recommended the hydro tranny for loader work were right. The work I was doing was in a tight spot and the hydro made the back and forth and...

Test drove a 3038E today with FEL. First time I've ever driven a hydro. It felt weird. I have an old JD750 that I'm thinking about replacing. The dealer has a 3005 with FEL for about the same money. The 3005 is the exact same as a 790 and since it operates about the same as a 750, it...

Hi, this is my first post. I am been reading on here for some time and have found a lot of useful information. I currently have a 1970s White (oliver) 1365 tractor. It is about 55hp. I bought it to brush hog some land I bought. I now have 4 acres, but will be purchasing an additional 4 (and...