ford 1910

I'm shopping hydraulic top-links for my Ford 1910. Seems some measurements are what I need - no problem. However, I'm now noticing a large "Made in Korea" stamping on the manual top link I currently have on the tractor and thinking "hmmm, prolly not stock..." Plus, it's not blue! When...

My 1910 problems began with hard starting and a surging idle. It would have a rough idle followed by a high rev and back to a rough idle or just die. I had just began building my my shop and the tractor problems were put on the back burner, That was a year and a half ago. Shop is done and the...

Hi everyone — I searched for “k-seal” and “blue devil” and “head gasket seal” and didn’t get results so asking here: My 1910 has been running hot (the line just below max after 10-15 minutes) and needing antifreeze. Today I gave it some very light duty and it went to max temp, and started...

Would anyone know the part number for the 4wd sliding gear in top of transmission 1984 ford 1910 tractor? It wouldn’t let me post a picture, I ordered a manual but it’s a month away

trying to find a used steering box any suggestions?

I’ve been trying to install a new westendorf loader on my ford 1910 however I can only get the psi above 200 on the diverter block when I put the 3 point hitch lever all the way to the top in the notch area, however once in the notched area the psi will be at 2000. Does anyone have any...

Hi all, My starter solenoid is acting goofy. When I engage the starter with the ignition switch the solenoid activates the starter just fine for about one revolution of the engine and then the solenoid returns to the disengage position while the starter continues to spin. I thought this would...

Greetings, Replaced the timing gear cover gasket and started looking for the torque specs for the bolts that hold it on. Been through all of my manuals (including the repair manual) and the closest I came was a reference to the reinstallation of the timing gear cover in the "engine" section...

New to owning a tractor - so pardon the dumb questions. I have owners and service manuals but they are pretty poor and hard to follow for this tractor. I can't seem to locate where the front and rear differential fluid fill points are, and am also wondering do they need to be filled...

First time posting. First day with the new (to me) tractor. Plowed a small garden plot for about 45 mins and then put it in the garage. Later noticed a puddle of fluid on the floor. Not a lot, but enough to be concerning. Looks like it's coming from where the drive shaft enters the...

Good evening, I’ve taken on a project in restoring an auction buy non-runner Ford 1910. Apart from a cracked crank, which I’ve sorted with a second hand one, I’ve also discovered the front near side pinion has worn down(as result of bearing braking and years of metal smashing around in the...

Greetings, Been fixing up the old tractor fuel system. Right now, I'm trying to locate an equivalent fuel injector (or rebuild kit) for my 1984 Ford (Shibaura) 1910 tractor. The part numbers are: SBA131406230 (Single) SBA131406220 (double) I've been scouring the online shops and finding...

My tractor sits a lot but is in great shape. It's a 1984 Shibaura (Ford) model 1910 3 cyl diesel. It starts but is reluctant to do so. Takes about 20-30 seconds of cranking (after 10 seconds of glow plug warm-up) when cold to get it to catch. The other day, while I was using it and the engine...

My tractor is stuck in reverse. 1910 4WD with shuttle shift synchromesh trans. I have removed the top plate and do not see anything broken. The shifter rail will not move out of the reverse position. Prior to becoming stuck, the tractor became hard to shift into any gear. I am wondering what is...

Does anyone know where to find an exact replacement for wheels on a 2wd Ford 1910 I need the front and rear wheels for a restoration

Anyone know where to find a roof to fit a ford 1910

Hoping someone can help with my 4wd issue on my compact tractor. I did hear a loud pop when the 4wd quit working. I had the tractor off the ground today and if I turn one front wheel the opposite wheel does not turn. I took the left front tire off and the left front drop axle apart and...

Interested to hear other owners opinions and experiences

If I were to use biodiesel in my tractor what are the pros/cons

I’m wanting to know which transmission my Ford 1910 has there’s two types a synchromesh transmission and a non synchronized how do I need to check

My Ford 1910 is very light in the front with the 5 foot bush hog on it I ordered 5 50 pound weights that are the same as the originals will that be enough to make a difference

Does anyone know where to find a white roof for a Ford 1910

I’ve gotten a Ford 1910 recently and I would like to know what all I should check and replace to restore it back to it’s original power and condition it only has 820 original hours on it.the only part I’ve replaced on it is a seal on the hydraulic piston which made a huge difference on the...

Where can I buy a new air intake hose, part number SBA314540451, for our Ford tractor model 1910? It has a Shibaura engine.

I had my little 1910 sat in a little wood I own. I. Looking for a mower to fit it to cut a few acres of grass. I also pull the odd tree out for cutting. Recently some arsehole took it apron themselves to start the tractor drive it through my little wood shed flattening it the cut my fence and...

Team, I'm looking to replace the lightbulbs in a Ford model 1910 tractor. Current bulbs are incandescent 12V35/35WS and I'd like to upgrade to LED style. Any conversions bulbs known, or a website that I could begin to research. I've googled a few times, but nothing appears to be available...

Hello, I recently acquired a property and the previous owner left a 1986 Ford 1910. The tractor is in fantastic condition but unfortunately, it is missing the engine oil dipstick. I have searched all over the internet to try and find the OEM dipstick or a universal dipstick that would fit...

Hi All, I have a '84 Ford 1910 that had the OEM mechanical voltage regulator that was putting out just a little over 17 volts to the battery. I have no idea how long it had been doing that but thought it would eventually fry the battery so I replaced it. I ordered a mechanical one but got a...

I have been working on an '84 Ford 1910 for a friend, and one of the big projects has been to mount and plumb a Woods 1009 loader on the machine. I got all of that done, and thanks to chander for a bunch of help, I was able to get the loader working and sent the tractor back home. I thought...

I'm considering purchasing a smaller tractor for running a finishing mower and found a '90 Ford 1910 with turf tires that I'm planning to look at (have not done so yet!) The clock has 789.5 hours on it - I assume that's not accurate on a 30 year old tractor. Does anyone here own or have any...

I have a great little 1910 that lacked a loader when I bought it. I found a loader from a machine (also a 1910) at Weaver's and am having trouble figuring out the plumbing. The 1-arm loader valve (also a Ford made by Diesel kiki) has the two hoses that go to the diverter block, plus a port that...

Ford 1910 Compact Tractor Seatbelt Attachment Points? Greetings, Have a great little 1910 (1984 model) compact tractor that I managed to find an ROPS for, so need to also reinstate the (missing) seatbelt. But, I can't find any literature that indicates the attachment point for the bolt-end...

New-to-me Ford 1910 (1984). Looking for photos of how the ROPS posts attach to the axle. Or anywhere. I bought the tractor without an ROPS and found one for it at a salvage yard. Can't find any instructions as to how to mount it in the service manual or operator's manual. Any help is...

Have a line on a 771 and need a loader for my 1910 tractor. Anyone know if these will bolt up without modifications? I know the 771 was specified for the 1900 (and the 770A/B for the 1910), which is close to the 1910, but don't want to commit to a costly mistake. Thanks, Jim

Good morning, A new 1910 owner with operator and service manuals in-hand. Unanswered question: What material is the fuel level tube (that serves as a fuel gauge in pre-July 1985 1910s) made of? Mine is crusty, opaque, and crispy. I thought it was a metal tube until I saw that the ends were...

I've never owned a tractor before buying this Ford 1910 with Synchrcmesh transmision shuttle shift. I ordered a 6' county line tiller for and trying to learn how to use it properly. Downloaded the operators manual and I'm confused how the shuttle shift pattern works?

Need a little insight on this one. I have an opportunity to get a 1510 for parts, and I own a 1910 that the front axles are missing, as well as the transfer case. My question is, are the 1510 and 1910 front axles and parts interchangeable?

Hello, I have dismantled the fuel injectors from my 1910, the first one was just like the books say but one of the nozzles had the center pin fall out. Every where I see exploded vies of this fuel injector it shows it as an assembly, not showing the pin out, the nozzle has the pin as part of...

Hello, Can anyone help me with removing the water pump on my ford 1910? I just installed new sleeves, pistons, rings, valve job, head is back on but I want to replace the water pump gasket. All bolts are removed, it rotates side to side but will not come off. I have been hitting it with a...

I have been having an issue with my three point creeping down when my loader is attached. I think it is in the divert valve. It doesn't do it with the loader detached. I took the valve apart and checked the spool. Everything looks intact and moves freely. There is a groove toward the top of...

Morning! I'm brand new to the tractor world. I have driven a few back when I was young but I didn't really pay attention to what I was driving, just the job at hand. So, the ground this tractor will be working is hilly, somewhat rocky, red dirt ground. I know I need a MFWD or a 4x4 tractor. I...

I have a Ford 1910 that yesterday blew a hole in the side of the block. I suspect that it dropped a valve. Not interested in tearing it apart. Has a 770B loader 4x4 everything works great, turf tires 1700hr A new block plus rebuild kit is going to be $2500+ in parts & shipping not including...

Found a Ford 770b loader to put on my 1910,,the hydraulic connections on the block that I took the loader off of are parallel along the top of the block, the block on my tractor, one is along the top and the other down a little toward the center,,anybody know which one is the feed and which one...

I am replacing the water pump on my newly acquired Ford 1910 tractor. I am considering removal (not replacement) of the thermostat while working on this job. I live in way south Arkansas and plan on using this tractor in the warm/hot months only. I'm retired and if the outside temperature is...

I just bought a 1985 Ford 1910 tractor/loader that didn't not run, looks great, nice and tight but I was told it just had an injector pump problem. I was lied to. I need to find a rebuilt head and possible complete rebuild kit but after spending hours, days, weeks searching the internet I am...

I have a Ford 1910 with 13.6 x 24 Ag tires. I'd like to get something a little more friendly to the lawn, but not so bad it's worthless in the snow. Something in between an aggressive ag vs. softest turf tire. And, what would I shop for if I wanted to use the same rims that I have now. Is it...

Replaced cylinder head on Shibaura 3-cyl diesel on 1983 Ford 1910 tractor. Preparing to adjust valve timing and need some help deciphering the 2 marks on the flywheel. See attached photo. Thanks for any guidance on how to interpret those marks: TDC and some angle offset? AND Can't find any...

I have a 1910 that was working fine until I found it with the key on. I have a service manual and ran thru all the tests. I tried a new alternator - nothing. I have tried 3 new regulators and with all 3, the light doesn't come on and they click when connected and key-off. This is getting...

I have a 1910 that I've discovered has a leak where the injectors are screwed into the head. Crazy how it was discovered. I was refueling and spilled a bit of diesel fuel over the engine. What I eventually saw, was right where the injectors are going into the head, there were air bubbles...

I have a Ford 1910 with the Shibaura 3cyl diesel. It has been trough a lot and the diesel has got to the point of being beyond repair. By me anyway. I'm looking for advice on possibly replacing the diesel with a cheap 4cyl petrol engine from a scrapped car. Has anyone seen this done or can you...

I have a 4wd 1910 with shuttle shift that needs a transmission overhaul. New Holland no longer stocks parts. Did any other tractors have the same transmission? Are there other transmissions that would fit? Any advice would be greatly appreciated.

Hi, I was wondering if anyone would have standard crankshaft sizes for a Ford 1910? Thanks:)

Hey guys, I have a Ford 1910 with 770 loader. The tractor has a hydraulic manifold block in front of the brake pedal that can switch the hydraulics from the loader to the 3pt. One of the quick connects on the manifold for the loader connection has been leaking so I ordered new couplers. Changed...

New to this site. If I seem lost I may be. Please be patient. Parked my tractor for about a month maybe longer but not much longer. hyd's worked fine when parked. after work was done on house I jumped on tractor to get it ready for winter and no hyd's. Changed the filter and the hyd's worked...

Hi folks - just joined the forum. As the title says, can anyone tell me what RPM the engine will be spinning if I'm turning the PTO at 540 RPM? I'm looking at getting a PTO driven generator and am curious how fast the tractor will be running. My understanding is the tractor was new in 1991...

So, I'm working on my tractor because there a pretty good knock when I first start up the tractor. Once it's warmed up for a minute or so, it goes away. My natural assumption was that the valves needed adjusted. I bought the tractor about 2 years ago, and I haven't touch this maintenance. I...

Hi new here just recently bought a 1986 1910 4x4 I have a guy putting a new clutch in it. And who ever worked on it before screwed up the first part of the threads on the crank where the flywheel attaches I ordered a new nut and want to clean up the threads before putting the nut on. My...

I have a 88' Ford 1910 tractor. The other day I noticed that the battery light came on and was staying on. ( I replaced the battery with new interstate battery approx 6 months ago- when it failed at that time). I tested for alternator output at the battery and there was none. I purchased a new...

Im looking for parts for a ford 1910 cant find this part on any diagram. Its some sort of port/ nozzle for the fuel. Its goes in the bottom of the cylinder head opposite of the fuel injector. Any help would be great. Thanks Dave

Hi Folks, Just wondering if anyone knows if the timing cover needs to be removed to replace the seal for the crank shaft?

Hi all Just picked up my first tractor ever, a 1984 Ford 1910 with 1600hours. Few questions: It has some trouble starting. I let the glow plugs go for about 15sec and then crank it (been warm outside 50-70F). It sputters and smokes and wont start usually. Let it rest 10 sec and the second time...

Can you adjust the rear diff lock? I have a Ford 1910 that is behaving this way: If I press the diff lock pedal down, nothing happens. If I use my heel to lift it up, I can get it to lock, but then is will not disengage until I clutch and shift into reverse (or so it seems). Even if I...

I'm new to this forum and found a few posts that touch on the issues with my Ford 1910 but not everything at once. At low RPM (or with the engine off), the three-point hitch will not support a load. It also drops if I raise the FEL boom. Keeping the revs up above 1500 or so keep the 3PH in...

First time this happened it sent hydraulics oil into the motor. Took pump off and really at that time checked the shaft for wear and just replaced the seal.. The next day after replacing seal it didnt again when i was using the front loader. I took the pump off and again and the seal was more of...

I have a 1910 ford tractor. Could anyone help me with the valve clearances and the procedure to do it? Thanks, Jeff

help! have a 1985 ford 1910 tractor, and its barely able to move or brush hog when it gets warm! would a clogged fuel filter or other filter cause this? i have yet to change out any fluids or filters. any suggestions would be appreciated!

Hi All, I am a new owner to a '84 Ford 1910. I have been on a 30 HP utility tractor plenty in the past 30 years pulling a bush hog mowing pasture but now I am entering a new horizon in that I want to install an implement (Mesquite Puller) that needs 2 hydraulic circuits to function but I need...

Hello, I just recently inherited my tractor with the purchase of my new home. I have noticed that I have been getting stuck a lot this spring with the soft ground and observed that only one rear wheel is spinning even when in 4 wheel drive. Today I lifted the tractor off the ground to inspect...

Fuel gage doesn't work on my 1910. What do I need to do to check it?

Anybody ever replace the brake shoes on their 1910? How bad of a job is it? Do you just pull the fenders, then take the bolts out of the housings, and that exposes the drums?

What should be the voltage at the glow plug when the key is turned to the preheat position? Right now I am getting about 9.5 volts. I looked at a wiring diagram and believe there is a resistor (the indicator on the dash) in the circuit that would cut the voltage but I am not sure by how much...

Hi All, I checked the search and didn't see my issue. My ford 1910 front end was locked up in and out of 4wd. If I lift the front off the ground the front tires spin free in opposite directions. I have the repair manual and it seems to me that the spider shaft pin is broken and the pin slid out...

Ok, well I'm continue to upgrade my Ford 1910 machine. So far, here's what I've done: * Changed all fluids and filters. * re-cored the radiator * new thermostat and gasket * rewired the lights * adjusted the PTO clutch * installed/fabbed a left foot pedal * adjusted the breaks * tested the glow...

I have a Ford 1910 with 770 loader that I am replacing the ridgid hydraulic lines on the loader. Anyone have any tips/suggestions on start-up i.e. priming, air in lines etc.? TYIA

hi guys, I have a ford 1910 that I have always had problems with my hydraulics freezing up when it gets really cold. Usually after let her run for a bit they get warmed up and start to flow properly. I let her run for an hour the other day and had only partial power steering, which usually...

I have a ford 1910 that has a rotted out rim in the rear. Replaced the other one last year with one from the NH dealer, which cost about $500 for the part. Does anyone know if there is any crossover with rims from other makes and models? Tire is 13.6-24. Does anyone have a suggestion for an...

I have a ford model 1910 and the hydraulics have slowly deteriorated to the point where the bucket no longer moves and neither does the 3 point hitch lift arms. When I changed the oil filter, things seemed to work fine for a short time and then quickly deteriorated again. There is some sign of...

My tractor started missing like it might be low on fuel so I stopped and filled it up. When I tried to restart it I got a few puffs of smoke out the stack (normal) then nothing. I changed the fuel filter and disconnected one of the fuel lines into the cylinder and cranked it to see if fuel was...

bought a used 86 Ford 1910 tractor. having an issue with the shifter stay in gear. both the gear and range just wiggle in the wind. any thought s what might be going on?

Posting hyd info from recent fix. I am acft mechanic 34 yrs. recently my 1910 3 pt lift ceased to wk. I have a service manual and set out to fix it. 1st I tried the hyd press test as called out in the manual. The manual does not spell out the test very well but after all my work I got it figured...

Posting hyd info from recent fix. I am acft mechanic 34 yrs. recently my 1910 3 pt lift ceased to wk. I have a service manual and set out to fix it. 1st I tried the hyd press test as called out in the manual. The manual does not spell out the test very well but after all my work I got it figured...

I am relatively new to tbn and recently purchased a 1985 Ford 1910 with a loader a 5 foot bushhog...which would be considered my "first" tractor. I will start by giving you a little info on myself and then i will get get to the aim of my project. I am 16 years old and i am a junior in high...

Hello, ijust bought a ford 1910 with turf tires and am thinking of changing to ag tires. Does any one know of any other make wheels or center disks that will work on the rear of this tractor. They will be a lot easier to find if i am not limited to ford wheels. thanks in advance, Ron

Hello All, I just recently purchased a Ford 1910 with a Du-Al loader for $3500.00. I plan on using it to landscaping work around my place. The amount of hours on it are unknown. But, everything seems to work except the 4wd will not engage. It was used inside a building to load coal and the...

I've gone thru all the wiring on my 1910 and replaced the voltage regulator but the tractor will still not charge. The charge light remains on. I've checked all my connections but still can't seem to find the issue. Voltage is 12.35 before start and after starting - no change. Any thoughts?

almost killed my helper how do i get at shoes i started on the right side removed finders then the small bolts when i got to the 15 16 bolt my voice in my head said you need more info , so please let me know is the 2ed row of bolts for the hub and do you remove them i do not want brake it

I have a Ford 1910 manufactured in 1986 and the front differential oil has started leaking out steadily. It emerges at the 2 front wheel drive unit at the point where the top half of the unit joins the bottom half. Both are leaking, the right side more than the left. The level of oil in each of...

Newbie here with a counterweight question, and not able to find an answer using the manuals. I'm going to make a concrete counterweight for loader work, but can't decide what weight I should aim for. The owner's manual for the 1910 has information on using cast iron wheel weights and loading...

I bought an old 1986 Ford 1910 last fall. Hydraulics were working. It sat outside all winter-covered when the wind didn't blow it off. It got water in the reservoir. I drained it a little and put on a new filter. The fluid is all creamy-I even tried putting the old filter back on. The lift...

Has anyone rebuilt a Ford 1910 3 Cylinder Diesel? Was wondering how hard it is or costly to replace sleeves and pistons. Is it worth sending to a shop for repairs? Any info would be appreciated. Thanks

Re: HELP PLEASE- Ford 1910 - ANTIFREEZE IN THE OIL- HEAD GASKET I had a chance to run the tractor. The top radiator hose gets warm and so does the small bypass, but the lower radiator hose does not. Bad thermostat? The gauge does not work. What do you think? Should I go to the dealer for a...

Hello Everyone, I have run into a little problem. I have split my tractor for an engine rebuild and now have to rejoin my tractor and I can't find a clutch alignment tool. The tool steps are; 15/16" 13 Spline and 1 3/8" 19 Spline. This is a dual action clutch and I just can't find the tool...

I have a mid 80s 1910 4wd with 1180 hours. It runs like a champ and is impressive for the size and weight. After a couple of months of moving soil, I hooked up my finish mower and discovered that the secondary clutch would not engage the pto. Your posts on this topic have been useful, thank...

I have a Ford 1910 tractor which the PTO disengages when trying to shred. I was curious why this may be occuring? Should I add hydraulic fluid? the PTO operated fine but after shredding for a while it began disengaging. The tractor belongs to my father so I do not have much knowledge about it...

Any suggestions on how to disengage the diff lock? Tried pulling it up by hand, but no luck.

Hello all, What I have is a 1986 Ford 1910 2wd with a frontend loader added on(Ford). My problem is since I've owned the tractor the frontend loader will operate extremely slowly with an implement on the back such as a bush hog or disk that is in the fully raised position. If I lower the...

Hi everyone, could use some advice on a 4WD 1910 with 770-A FEL. It has 1482 hours, and a fair amount of surface rust. I don't care about appearances all that much, as long as it works, I can always make it look prettier. It is a 1985 according to the serial number, I have not yet had a...

so it all started with a charge wire to the starter terminal getting hot. I replaced the regulator and also the ignition switch, since it had a spot were it would not connect to the glow indicator if not in the right spot with a steady hand. I replaced the original switch with an aftermarket 4...

Looking to purchase front axle bearings, seals and gaskets

Has 4WD, 665 hours and 7108 loader. In good shape. Shedded. Seat, paint & metal look good. Checked Tractor House looks like ~$7,500, but there's not many for sale to compare.

Hello I'm new to this site. I was wondering if anyone could help me with some problems I'm having with my series 1910 Ford Tractor. I need to know how to adjust the lifting pressure?? Any takers on that?? Just let me know something if you know something, lol. Thanks alot I appreciate it very much.

I am looking to purchase a ford 4x4 diesel 1910 tractor. It has 2900 hrs. The pto brake doesn't work. The owner says the pto doesn't stop when you press in the clutch. How big of a deal is repairing something like that? I know more info is needed. But what price range could I be looking at to...

I'm very seriously looking for a backhoe attachment for my '85 Ford 1910. I see that Ford originally wanted to pair either the 757b or 758b with my unit. I see that the 758b has a deeper digging depth, higher loading heights and slightly more digging force. I also know that they used a subframe...

I have a well used 1910 with a back hoe powered by a pto driven pump. As far as I can tell the back hoe has not been off it for a very long time. Provided the rpm is low the pto can be engaged with no real problems and I only realised the clutch was not releasing just recently when I was...

I currently own a Model # 1910 Ford Tractor and I found a model 702A snow plow will it fit? Any help would be appreciated. Thank you.

Does anyone know if a Bulldog 285 loader will fit on my Ford 1910, any help appreciated.

Hi All, New to Forum.........Been having hydraulic lift problems on '83 Ford 1910 4x4 Tractor and wondering if anyone knew of sure way to test Hydraulic pump and pressures. Don't know what else to check. Lift arms will go up if no implements are connected and then only at about 1500rpm. I can...

I have a ford 1910 tractor that when i try to engage the pto to operate the finish mower, it grinds while engaging, even at the lowest idle possible w/o stalling the tractor.Whats the problem and whats the fix? thanks inadvance.

I'm buying a ford 1910 with frontend loader with 600 hrs a bit weathered but in pretty good condition.I have a ford 8n but would like a tractor with a frontend loader.

Hi Folks, New here and need some insight into your experience. I have a Ford 1910 4x4 with Woods FEL. Recently while plowing out potatoes, I was checking everything out, fluids, greasing, etc when I noticed a "crack," where the right FEL loader mount bolts onto the tractor housing. The crack...

I've used my tractor for the first timetoday..I mean more than back and forth pratices while waiting for the snow. Wich snow arrived today so I went out to get it working a bit.I needed to go back and forth from 2 wheel drive and 4 wheel drive and sometimes it wouldn't disengage..the little...

I wondering how much to ask for my mid 80s Ford 1910 4x4, about 1000 hrs , comes with 702B dozer blade and 5 ft Woods bush hog , The tractor and blade are in good shape , bush bush hog is fair, but cuts good !

Does anyone have a pic of the shifter that is on the column. I believe there is 4 gears and the reverse on the column. Yesterday a piece came off or something shifted which cause it to stick. I couldnt get it in reverse. I took the linkage off thinking i could manually do it there but it felt...

Trying to score a 1910 from a guy here locally. Going to look at it saturday. They disassembled the front of the motor (3cyl diesel) to get the injector pump off and havent put it back together yet. He says it ran good before that. The guy is asking 1000 for it. Says he has all the parts. Am...

Hi, Is it normal for my temp gauge on my 1910 to show high temp when switch is off? When I turn that switch (ignition) fuel gauge goes up but heath down to cold as it is when just started...This is a recent acquisition and did not use it much but it doesn't sound right! Another question...

Hello All, I have a Ford 1910 Tractor with some PTO clutch issues. I purchased this tractor last year for $8900 up in Washington. When I push the clutch down all the way the PTO does not disengage. It still spins. The only way to engage and disengage the PTO is via the shifting lever but I...

Hi,here is a picture of the 1910 I had recently.1200 hours,1986.If I can I will squeeze-in a second photo showing a cut wire sticking out from the transmission cover...anybody knows what is it for? Hydraulic oil temp sender I can think of but there is no guage for it!Reverse light maybe? thanks...

Hi, After over a month scrutinizing tractor ads,when I saw this 1986 1910 with an Allied 380 loader and a nice vintage 72 inches McKee snowblower,1200 hours,I jumped right in at distance through the phone unseen! Altough I have not used it,working with it yet,it appears in excellent shape...

My Ford 1910 has always needed 20 seconds of pre-heat to start and this has always unsured a prompt start. Until this week! I noticed the engine turning over quite a few times before it would start even with the pre heat. The check wire on the dashboard still glows hot and I have taken the...

does anyone know how I plumb a backhoe into my ford 1910 has loader with quick connect but not for hoe if any one has a 1910 with a hoe pics would save my life I am not totally ignorant on hydro but cant get my digger to dig

Hi all, New tractor owner here....yes I'm a girl, but I hope ya'll won't hold it against me haha... Anyway, my question is this, we need haying equipment and I don't have a clue what my tractor will handle. We recently were offered 25 acres of flat land to take hay from. I am trying figure...

Need to remove the drive shaft on a 4wd 1910, what is the trick. I have removed the 4 bolts attaching the collar to the front differential and the single bolt at the rear. I have clue I might have to remove the rear part (don't know official name) were the drive shaft goes in, but not sure. Help...

Trying to help my Dad find a glow plug for his pre 1984 Ford model 1910 tractor. I ordered him one online but it was too long. He has pulled one out and says its a NGK 544. I've sent an inquiry into NGK in addition to this site which seem to have many for sale but not what I need. NGK Glow...

i have just gotten a 1910 and we are getting around to changing fluids and filters before we put it to work, i need to know how to change the oil for the injector pump a diagram would really help out a lot!

I am starting to look into a replacement for my 1910 Ford and going for a little more Hp and getting away from the two stage clutch but keep the gear transmission. I have it narrowed down to these possibilities Branson 3820 or 4220, Montana 3840 or 4540, Mahindra 3510 or 4110 and NH TC40 0r...

I recently purchased this tractor used, and it didn't come with any of the operator manuals and most of the operation decals are gone/painted over. It's a 1986 model year Ford 1910 tractor with a 770B loader. I have 2 questions.. one about the tractor and one about the loader. On the tractor...

I have been looking at a Ford 1910 with a Dual 110 loader.It has 1429 hrs. and is a 1986.The price is around $8000.My question is,is this a good tractor,at a good price?Thoughts anyone? tnx,stan

Hoping someone can help, I need a picture of the airhose, on a Ford 1910 3 cylinder. The hose goes from the intake to the aircleaner. My tractor is a Bradco conversion backhoe/loader. It uses a different nose piece and I believe the hose is not what came from the factory, I think the aircleaner...

Hello, just found this site! I have a ford 1910 4wd with a 770 ldr and need to plumb in remote hyds to operate a jd 1207 mower conditioner that I want to purchase. What is the best way to operate this mowcon? It is my understanding that the lift cylinder on the 1207 is a one way acting cylinder...

nhown-ML-725006-ML- brand specific

power steering leaking around the base of the steering gear assembly. Just bought this tractor and I am not sure what the solution to this problem is, any suggestions welcome. thanks gerry

I'm looking at a Ford 1910 tractor. It has 978 hs. on it. It is slightly weathered, but that is mostly cosmetic. A can of spray paint and some sand paper and she'd look great. I think she is a 1987. The current owner has had her about 8 years. Never had a problem. Has only been worked on...

The three point lift on my 1910 will not lift a 6ft bushhog after the hydraulic fluid heats up. Also when an implement hooked to the three point is lifted to a neutral position not fully up the arms will bounce up and down. I have replaced all the o-rings in the control valve, could it be the...

I am a first time tractor buyer looking for a used 4 wheel drive tractor with loader to maintain 35 acres. I've found a Ford 1920 without a FEL for $10000, and a 1910 with FEL for $7500. Both have just under 500 hours. Is the 1920 worth the extra $. I assume I could add a FEL later. Any...

I got it all apart, the ring gear is shot and so is the drive gear. How on the green earth do you get that thing out? Any help would be great.

Pulling a stump in reverse something started skipping in the front end. Well 4 wd you could not use, the left front wheel locks up. So I used 2wd, now the 2wd is locking up. should I drop the whole differential off and work on the whole thing? Is that whats probably wrong?

I have a Ford 1910 with the syncromesh transmission. I have recently developed a problem where the transmission would jam when shifting from reverse to the forward gears. I would have to jiggle the column shifter quite a bit to get it to release. At first I thought the problem was in the...

I have a well seasoned 1910 ford, last week i went to move some snowbank(weather has been 10-20 degrees), made one pass and the hydraulics were dead, no loader, no hitch, no power steering. feared the worst, hoped for the best. 2 days later came home w/ new fluid and filter...before the change...

Ok, Does anyone have an idea where the vent for the front differntial on a 1910 Ford is located? I've looked all over. I can tell it's plugged due to the fact that after driving around when you remove the fill plug you can hear the pressure release. Thanks, Folks