branson

Hello all, The tension adjsuter blew off last night due to the heat and bad parts I guess (held together with plastic) - There are no replacement parts from branson/ Tym without buying the whole 1200$ chair and tensioner. Any ideas on a generic replacement that fits? it is probably in...

Who’s the go to on-line for Branson parts? Don’t have a good local dealer anymore. Thanks in advance.

Greetings. Wondering if anyone (LouNY, anybody?) could check their Shop Manual, Pg 2-151, and tell me if theirs states any particular number (e.g. .008", .030", whatever) to look for on the Dial Indicator once the plunger on the Inj./Pump stops moving (and Dial Indicator bezel is set to "0") as...

OK, a mystery wrapped in a puzzle inside an enigma as they say: Bought a Branson 3120 new in 2011. (Been a very good tractor for my needs, btw.) Always thought I had the A1700N2 engine and the '20/25 Series Tractor Service Manual' put out by Branson Tractors (Pg 1-26, 7.2 MAJOR SPECS) that I...

One thing I've realized after watching the TYM honcho's vids about the advantages of a strictly mechanical fuel system vs. the electronic fuel injected systems most if not all other mfg's have gone to is he makes a great case. Yes, an electronic system (assuming it and all related components...

Did a compression test yesterday on my 2011 Branson 3120R with the A1700 engine. LOWEST reading (#1 Cyl) was 465 psi! Thanks to this forum I learned the factory numbers were like 497 psi so WOW! Engine has approx. 1700 hours and is used not daily but regularly to brush hog, load round bales...

On the 100 hours the piston broke, i reported it, it was still under warranty. Dealer replaced it. Now the boom has cracks!!!!! They beefed up the hydraulics but forgot to beef up the tractor This is when the piston broke actor

I have a 2020 Branson 4820h. I made a dumb mistake back dragging and bent the left curl cylinder. Im looking to upgrade both curl cylinders now and quit back dragging! Lol. My question is, has anyone else done this and what issues did you run into changing out the cylinders??

2 things, is this fluid ok for this unit? I use it in Kubota G1800. Also I think the 3 point arms are backwards. Just ordered bonded dowty washers to fix leaky 3rd function valve.

2021 Branson 2400H with push button on loader stick diverter valve. Leaking at fitting. Are these WR Long or factory from Branson? Looks like crush washers like brake lines? Or O rings are bad.

I know it's not a TYM but same engine 1.2 l A1100N2 Kukje. 2021 2400H Known as a good motor but this is what mine is doing at 395hrs. Saw one video of a guy that said injector timing was off and heater was never working? Had to do a "Top End" service. This white smoke at start up is concerning...

So, I'm on my 3rd Branson (4220, 5220c and 5520c) and I had one little mouse burrow in behind the firewall and I cannot believe the damage it did. Strangely, it not only chewed through the jacketing on the wires, but also the copper as well. The tractor is usually stored indoors, but I stored...

I know it was discussed before but i could not find any info on hydraulic oil filters cross reference. Just came across this site. Feel free to delete if this was posted before https://www.filtersfortractors.com/branson-2515h-filter-cross-reference-info/

I have a 2007 Branson 4220i that the handle for the remotes valve broke, i have welded it several times, but it just break, the handle looks like pot metal, the cost for a new valve is plan to expansive. I have heard you can buy an after market valve and mount it on your fender. Has anyone ever...

***SOLD*** 2021 Branson 2515H, 4WD tractor in excellent condition. 25HP Cummins diesel (no DEF), hydrostatic transmission, includes 5 ft. FEL with 2,200 lb. lift capacity, 5 ft. rotary mower and 5 ft. box blade that has never been used or put on the tractor. Purchased new on 4/15/21, it has...

I have a 2021 Branson 4820h with a Kukje engine Ser number TX3K00116 With 290 hours it's a hobby machine kept in an enclosed garage, serviced regularly, fuel is clean, fuel bowl clean. Here is what happened: Recently while doing some light work it start smoking and the engine began running...

I have a customer that I've known for years & just bought a 6640C & both front hubs are very loose & leaking & he wants me to fix it. I need a service manual for this tractor. I haven't found any downloadable manuals that my computer hasn't said are loaded with spam. Anyone have a reliable...

Hello, just treated myself to a 2023 Branson 3515H. I know that TYM bought Kukje from Dongkuk in 2016, they're making Branson's now, have rights to Kukje built machines (Branson, McCormick X1's, Bad Boys, etc..). But one small difference I noticed on the TYM 3515 is their front wheels have...

Branson 3510i serial # CNOM00164. I think it is 2011 or 2012. Asteral...Can you provide date?

The good news continues. Watching a video from Tony's Tractor Adventure about the 'new' T4058P. It's the renamed 5835r. (From a farm show) They are still innovating on those models. Some cosmetic stuff changed. They will be doing a cab one as well.

Located in North Central Pa. I have a 2007 Branson 4720H for sale and all shop manuals. Tractor has about 2470 hrs and runs good, starts right up and all hydraulics work. The front headlights don’t work. Feel free to reach out with questions. $8,500 obo.

A local mining historic site was unloading some artifacts with maybe 300 lbs in the loader bucket when the right front spindle broke off, taking the wheel and tire with it. There does not seem to be a Branson section here, does anyone know if this is a common failure? I wonder if Branson parts...

I have a 2023 Branson 4820R that had a red light come on yesterday that said Oil with a thermometer next to it. Cannot find it in the manual or anywhere on it. Anybody know what this is ?

Does anyone know if their is a sister brand the same as the Branson 2910i

Hello All, I just recently purchased a 2007 Branson 3510(I) shuttle shift, and am worried about how loose the shuttle shift lever is. I don't have any issues with it going in and out of reverse, but I have to hold the lever in the middle of the column for it to shift. Once I let loose of the...

I have a Branson F47 and I am unclear what the two small hydraulic levers do, the handbook isn’t clear. One seems to have three positions back middle and forward any advice wellcome

hello. newbie here. I have a Branson 2910 tractor with a hydraulic problem. where the main metal hydraulic line coming from the pump goes along the left side and ends just in front of the back left tire, I cannot find anything that will connect a new hose to that threaded end. It looks like...

Hello! I hope this is the forum for Branson tractors now that TYM bought us! Does anyone know if the mid PTO on a Branson 2400H is supposed to hook up to anything? I was just doing a service on it and noticed some damage to the front drive shaft. At the same time I saw an exposed, short, drive...

Greetings everyone. I'm a first-time tractor owner and purchased a 2022 5520CH with 260 hours last month. After about 10 hours of use this past week, I can no longer change my range. The shifter is stuck in range B and will not come out of gear. I don't see anything obstructing levers...

Hello, Is there a way to identify the year of manufacture of a Branson 2400H from the serial number on the tractor? I'm trying to find a parts and service manual. The ones online I have found are for tractors manufactured 2014 and after...mine must be from before that date.

jUST BOUGHT A BRANSON 4220 HAVE USED IT SEVERAL TIMES BUT DO NOT KNOW HOW TO USE THE LEVERS ON RIGHT AND LEFT SIDE CANNOT FIND A USRE MANUAL FOR THEM HELP ?

I own a Century 3045 (Branson4320) and the boot cover for the front propellor shaft housing leaks hydraulic fluid. I have loosened and collapsed the shaft housing so I can remove the shaft and replace the boot. I'm looking for Branson part # TN23030000A4 boot cover or a suitable replacement. I...

My Branson has the two speed pto 560/760 what engine speed should I select for each of these please as it doesn’t say in the manual Thank you Michael

2004 4720i nonhydro. PTO stopped while mowing. No metal sounds, just stopped. I have read through the pretty good PTO threads and have fuse, switch, coil as my trouble shooting path. I have had zero electric issues with the tractor since I bought it new. I looked at the fuse bank today as...

Hello, Has anyone had problems with their Branson tractor’s water pump? I am seeking suggestions for what needs to be removed and in what order. Thanks

Are there? Or if you have 5 ft, do you think it can handle 6 footer?

I have a Branson 2910i. 3 months ago it got hot then I had a puff of white smoke. I immediately took it in. Mechanic broke it down and found a bad head gasket and 1 loose piston/cylinder. We got everything apart all the parts but the sleeve we ordered for it was the wrong one. None of the...

Hello Forum. I am working on a 2045 Century for a friend, and I need to get parts. I believe there is a Bransom model that has the same parts as Century. Could someone please tell me what that model number would be? Thank you for any help.

Hello, I have a 2022 Branson 5835R that will creep foward in neutral. Has anyone have information on this? Thankyou

I'm using my Branson to row up bales and I shut it off at the day, now it won't start? Turns over good but will not fire. Is there a solenoid for the fule pump? Fuses are good.

The head gasket has failed on my Branson 4220. There are just 650 hours on the tractor, so I'm a little disappointed, but now I must deal with it. I noticed that the tractor was running hotter than normal, but it never overheated. Then I noticed that there was white smoke from the exhaust even...

I see that TYM is making a cabbed version of the 5835 open station tractor, it appears to now be available in a cabbed version. It is called the 6225 C, CH it looks like they may have changed the name of the 5835R to 6225R. Here is a pic from the TYM website. I can't be sure that they are...

Hi, I have a crank no start issue with my tractor. I’ve had issues with air in the system before when I’ve let it get too low on fuel. This time, full tank, went to start tractor and it only cranks. I replaced the fuel pump for good measure as it was older. Before I replaced it, I had my dad...

I HAVE A 2003 BRANSON 4720 . I REMOVED THE HYDRAULIC HOSES TO INSTALL A 3RD FUCTION FOR GRAPPLE. SINCE THEN THE REAR HYDRAULICS HAVE NOT WORKED . SO I PUT EVERY THING BACK STOCK AND IT STILL DONT WORK. MORAL OF THE STORY IS I DIDN'T TAKE ANY PICTURES. I NEED SOMEONE TO TELL ME HOW TO ROUTE ALL...

Can anyone share a link to this manual? (For my husband) Please and thanks

Hi, my starter went out on my Branson 2515H tractor and I am trying to remove it. I've unbolted up but it hits the Hydraulic fuel pump.I cannot determine any other way to get the starter out other than removing the hydraulic fuel pump? The tractor is in a field and not accessible to put it on a...

i am having some electical issues with my 2012 4720h. used it day before, went to hop on and start, the start sylonoid clicked a few times and then the whole thing went dead. now, no lights on dash, nothing when key is turned to on position, and no crank. battery is good, i have voltage to...

Howdy- new member here. I have a 2400h I bought used and partially disassembled so was unable to drive before buying. Tractor had tore up ring and pinion in rear end. Tore it all apart and replaced ring and pinion. Problem is reverse seems to work ok but having issues going fwd.. There is no...

Looking at a choice of these two tractors, with the price difference of the Branson/TYM ("Branson") being $1,500 more than the TYM-- and Branson not having standard rear remotes which will need to add which increases price difference. Seeking opinions on which one of the two would be the better...

If anyone's got a Branson tractor with the BH150 backhoe, would you please measure the bucket connectors? Relevant information: My tractor (3520h) has a "BH76" backhoe. Love it, dig it. Unfortunately, I've only got the one bucket, and in my (most of the year) hard clay+rock ground the 12"...

I just purchased a Branson 3510i tractor and am looking for an operators manual. All I can find is the repair manual.

Looking for some insight.... removed the BH last week and attached my mower. No PTO. Found a blown fuse. Traced wire and repaired a broken wire underneath. Checked everything, new PTO switch, cleaned PTO solenoid. New fuse and we are back in business. Mowed for about 20 minutes, lost...

My Branson 2505h started locking up on me today. I could pull forward slowly 4,6 maybe 10 inches before it would lock up and not move, touch the reverse pedal and it would move forward another little bit! I made it about 50 to 75 feet to the shop this way! Didn’t matter if moving forward or...

Hello everybody, my first time here. I’m a new tractor owner. 2023 Branson 2610H. I was looking over my owner manual for the bucket operation and I want to use the “float” feature but I don’t even know if it is equipped. When I push the lever forward as instructed with bucket level, all that...

Hello everybody, my first time here. I’m a new tractor owner. 2023 Branson 2610H. From what the dealer told me TYM is now the owner of Branson. Anyway. I was looking over my owner manual for the bucket operation and I want to use the “float” feature but I don’t even know if it is equipped. When...

I am having an issue getting my PTO to shift into gear. In fact I broke the arm (PTO Rod) that goes between the shift lever and the actuator trying to get it to shift. After the arm broke the shift lever moves up & down freely, so it has to do with the PTO Shift Lever Shaft or something...

My starter seems to have failed on my Branson 2515H... I have one month of warranty left on it! You can't just buy a solenoid either, and the new unit is around $700. Looking for tips before I start. Has anyone else had to do this yet? It looks like I will have to move a hydraulic supply line...

Does your 2400h go the same speed in reverse as it does forward?

Have a Branson 4020R that the foot peal and levee for throttle dropped working. If you use the throttle control on the console the throttle lever on the pump seems to stick but still does not accelerate with the foot pedal or the throttle lever on the console. Any suggestions would be greatly...

Hi all I just bought a 2016 Branson 2400h 4x4 with the sl00 fel and an MK Martin 60 inch blower. The lady I bought it from didn't post a price in the ad so when I inquired and she said $6k (CDN) I bought it. 324 hours on it. The only thing wrong with it is the rear hydraulic lift arms don't...

Need some help finding a spool end cap for a 2014 Branson 5220r FEL hydraulic valve, picture attached. Dealer of course said their solution was a new valve for $1500. Does anyone know the manufacturer of the valve? I think it's a Besco, but I'm guessing.

Tractor shows all fuses good, fuel shutoff solenoid getting 12.2 v, new fuel filter, air filter, will idle and drive about 100 ft then die, I am wondering if fuel pump or injectors are bad?

Last year my PTO clutch started slipping. I tried reading pressure on the back of the transmission where the hydraulic lines go in and had zero psi. Port g2 on the pto valve block and the port in the back of the transmission have the same pressures. The next step was tearing apart. I was able...

Does this 2 coil solenoid have a relay between ignition switch & solenoid? Does the 70 amp relay on left side of firewall under dash control any part of the fuel solenoid function? What is the function of the rectangular electrical box mounted on right side of firewall under dash? My fuel...

Hi All, I’ve lurked around on this forum for quite some time, but the realistic possibility of being a tractor owner within the month prompted me to join and get some insight, and hopefully reinforce my thought process. We moved onto 26 acres nearly three years ago now, but officially bought...

I know there are a couple threads here… but they are just running conversations, not truly cross references. My tractor uses the EA00004647A for engine oil. I can buy it from my dealer I’m sure. But, is there a good cross reference? I picked up a couple gallons of Rotella T6 today. Thanks...

Pull apart my tie rod assembly today at the point where i am pointing. Put it back together by using front loader to lift wheels , lined up assembly , lowered the tires to the ground, then turned wheel to get it to push back together. It came apart again. Repeated process. Is this...

can the rim and wheel plate be in any orientation to get the width you want? I have a 4720H and the 3 point stabilizer bars are too close to the tires since i installed the pat's system to run my tire chains. it appears that I can put the hoop on the rim on the outside instead of the inside of...

Hello I've been having an issue with my Branson 2515h over the past couple of months not shifting on the range shifter (A,B,C). Found the spring pin was sheared off, so I was able to get another one and get it replaced. Once replaced, it seems that there is still no resistance in the shifter...

The curl function on the joystick of my Branson 4225h is stuck. I'm not experienced at fixing stuff; can anyone comment on my reasoning before and suggest where to look next? (It's my week for breaking stuff...including the truck I could use to take the tractor to the dealer/mechanic, so it's up...

So, I was watching a Hank Hamilton video and he had Homestead make a grill guard for his T574. I took a look online and sure enough, they have them to order for 474, 494 and 574 models. $249 as of this moment. (13g). https://homesteadimplements.com/grill-guards-for-tym-tractors/ I decided...

Hi everyone, I need help diagnosing my issues. My tractor idles for a while before dying. However, when I have my RPMs up, like at 2500 RPM, the tractor runs fine and continues working. During idle, when using the bucket, the bucket drains a large chunk of my RPM. What could possibly be the...

Good morning! Is there an adapter out there on the market to connect to the Branson quick connect that would convert to the skidsteer quick attach or do I need to weld it up. I was hoping for something similar to this JD adapter.

I have a 2020 X.135 with the Kukje engine. It has 250 hours on it. I know in the beginning, I was not doing what I was supposed to do by keeping it at a higher idle. I had performed a few regens on it and never had an issue. However, this winter, it started to "de-rate" itself for any use, PTO...

I went to the Branson tractor site - I know they were bought by TYM - and the site is completely gone. Is it just me?

Having bitten the bullet and acquired a mini-excavator (KX-040), I think it's time to sell the BH760 backhoe I bought with my Branson 4225H tractor. It's worked really well for what it is, I just don't see myself taking the time to mount/dismount a subframe backhoe from my CUT (which I use with...

Hey folks, pulling the trigger on my tractor in March. That's when I'm actually moving onto my land. I've narrowed it down to the Mahindra 5145 Pros: -Heavy heavy tank -400 pounds stronger loader -Test drove and really like it -4 dealers within two hours Cons: -Shuttle only -MCRD -ECU ran...

I know the "backhoe or not" subject has been discussed many times here. I have read many of the threads. Love all the knowledge here. I seem to read either: -Everyone is crazy, mine is great -Waste of money overall My question is... if I don't expect the BH to be a mini-ex, and I do my projects...

I am getting very close to pulling the trigger on one of these two. I have spoken with the 3 dealers within a hour or so of my place. They can all get either model regardless of which brand they sold prior to the recent blending. Here's the tale of the tape for things that matter: Branson...

Saw a new video today from Mike at LSE in Nashville. They sell Kioti and added TYM about a year ago. Now he has Branson, too. I guess this gives us some indication of how TYM feels about Branson.

Hi Everyone. My Faithful FT254 snapped in half the other day after 12 years of service. It happened at standstill while lifting a relatively light load on the 3pt. I don't want to imagine the result of it happening while travelling. I'm sourcing the parts to fix it at the moment, but I won't...

I can not seem to find how to check the level of the oil in the front axle of my 4720h. I see the fill plug on the right side hub, but no stick or level check bolt?? my hubs leak a little bit and i want to make sure I keep it topped off. also, it says 80/90 on the fill plug, but the manual...

Hi there So after owing a Kubota B7000 with a loader I've built, I know how versatile a tractor with a loader is and the amount of things that it allows for us to do. Since this new tractor didn't come with a loader, mostly due to the price that would add. This lead me to search for an used...