Search results

Results 1 to 200 of 1046
  1. K

    Pole barn, build vs kit

    I considered a pole barn. I called a place that installs these car ports. They came out and installed a 30x30 14ft tall sides covered the gable ends, the rest left open for $6500.00. I use it to store my cattle trailer and my big CX105 tractor. It was a better price than I could get someone to...
  2. K

    Do it yourself Refrigeration and Air Conditioning

    Yes, Media makes mini splits with many different names attached to it. You want a mini with Joe's HVAC name plate attached, Media will make it ! lol
  3. K

    Do it yourself Refrigeration and Air Conditioning

    I hear it's also hard to get. I have also read there are some removing it and adding 410A:rolleyes:
  4. K

    Do it yourself Refrigeration and Air Conditioning

    like Korean vehicles, Korean appliances are also junk !. I owned one Korean vehicle and that was the last !. Haven't owned a Korean appliance, but I have friends that do and wished they didn't lol
  5. K

    Do it yourself Refrigeration and Air Conditioning

    Well, according to my sources with Gree, China will build any quality you spec. Higher quality = higher price point. lower quality = lower price point. So far, My Gree VRF (knock on wood) has been solid ! I remember when harbor freight sold junk for tools. As their tool quality got better...
  6. K

    Do it yourself Refrigeration and Air Conditioning

    My entire unit is made in China LOL. And as you know, Many of these inverter units and components are sourced from China
  7. K

    what size rotary cutter ?

    I can't answer that one. All I can do is tell ya what's listed in my Kubota MX5100 manual, and that's also what the Kubota dealer told me. I assume he read it from the Kubota manual as well
  8. K

    what size rotary cutter ?

    I checked my operators manual and posted the specs. recommended, which is 84'' and 1000 #. I did discuss the price of a land pride mower with local dealer. they recommended 7 ft land price at about the same weight at the LMC cutter I'm looking at for $3500.00 the land pride is stamped steel...
  9. K

    what size rotary cutter ?

    well, I may just go with the single spindle 7 ft med. duty cutter. 950 # I believe. It's 3500.00
  10. K

    what size rotary cutter ?

    yes , 3 py version ... and that atlas 1500 is 3 point
  11. K

    what size rotary cutter ?

    not too worried about the weight. I have pulled an Atlas 1500 disc at 1800 # to restore a pasture. so I don't believe the weight of the Iron craft 2408 would be an issue. I'm just worried about the PTO HP. being enough. As far as what I'm cutting, I mostly just lightly cut Bahia, Dallis grass...
  12. K

    what size rotary cutter ?

    under implement limitations in the owners manual, it list rotary cutter at 84 inches, and weight at 1000 #. just trying to get a feel as to what others are using on their tractor of the same size
  13. K

    what size rotary cutter ?

    I currently have a 5 ft. just going up one ft wouldn't be worth the cost. Plus 6 ft won't cover the rear tires. the 8 ft iron craft doesn't weigh 2K #.. I can get the 7 ft cutter that will cover the rear tires but it's single wheel and single spindle. the dual spindle 8 ft cutter has dual tail...
  14. K

    what size rotary cutter ?

    I've got an MX 5100. I'm hearing by some that an 8 ft dual spindle 3 pt. cutter is too much for this tractor, that the tractor is only rated for 7 ft single spindle no more than 1000 #, while some say it will run an 8 ft dual spindle just fine . I've been looking at an Iron craft 2408 cutter...
  15. K

    Removing gasket cement from inside of toilet tank - how?

    Don't know what your dealing with, but I've had good luck with brake parts cleaner. If your sure it's concrete, I'm not sure you'll find anything to dissolve it
  16. K

    Future of HVAC and industry supply issues.

    Worked on about as many millivolt systems as I did 24 v systems. Great thing about the millivolt system was, you had heat in the winter during a power outage. Later on, we replaced the old FF's for central heat and cooling systems. Used the old FF opening as the return !
  17. K

    Future of HVAC and industry supply issues.

    I've worked on thousands of these. Even installed a few way back when . Pretty simple units, but about every one was going to be a crawl to make repairs
  18. K

    Confirming Wire and Conduit size

    I'm no electrician. but have read about placing electrical wires underground/ in conduit, and consider heat dissipation and how it related to wire size
  19. K

    Buying a ZTR, what should I look for, or avoid?

    I agree. I bought a Kubota diesel Z TURN several yrs ago and have been pleased. Those diesels are very fuel efficient too !
  20. K

    Need advice installing a propane shop furnace

    that heater will never ignite that diesel hanging from the ceiling. Most fuel vapors like gasoline being more flammable that diesel, are much heavier than air and gather closer to the floor. It would take a lot of gasoline vapors to be ignited by that unit heater up in the air
  21. K

    Need advice installing a propane shop furnace

    I was just going by the pic you posted. I didn't see the walls insulated is the reason for that comment
  22. K

    Need advice installing a propane shop furnace

    I have hung them with all thread, unistrut. metal straps, etc, it's going to be a challenge to heat that non insulated pole barn to 55 deg. in the winter.. Attempting to do so is going to eat a lot of propane. Before I ever installed this heater, I would carefully inspect the HE for rusted out...
  23. K

    One inch from death

    I'm always jumping off my Kubota.. It's HST and stops in it's tracks when you let off the go pedal . You are one lucky person. It only takes a split second to get seriously injured, or killed. Saw a woman over the weekend get thrown off a horse she has ridden many times. For some reason, the...
  24. K

    Equipment buying negotiation strategies, haggling stories sellers, etc.

    Mine wasn't a demo and I really didn't need the wheel/tire upgrade, or the winch. I had never gotten stuck in the 4010 that I use to own and it didn't have a winch. just got a better deal on this because it was a left over 24 model ranch edition .
  25. K

    All Things Rural King

    Better prices ? Guess it depends on what you're buying. I can buy 2.4.D at TSC cheaper than Rural King . Same brand https://www.tractorsupply.com/tsc/product/gordons-amine-400-2-4-d-weed-killer-2-1-2-gal https://www.ruralking.com/2-4-d-amine-weed-killer-2-5-gallon-11320-102
  26. K

    Equipment buying negotiation strategies, haggling stories sellers, etc.

    I just purchased a new left over Kawsaki mule pro fxt 1000 ranch edition . I pretty much did all negotiating over the internet. I offered 18K out the door, and they wanted 20 K out the door because this UTV had upgraded tires and wheels... I told them I was negotiating on the same type UTV in...
  27. K

    Burn barrel question...

    I order a lot of stuff here at the farm. I get a lot of things packaged with Styrofoam. I bust it into smaller pieces and place it in the garbage container for the garbage truck to haul off. Sometimes, It takes a couple weeks to get it all gone, as the garbage truck only runs once a week here ...
  28. K

    Burn barrel question...

    take them to the metal recycling facility, or cut them up with your HVAC torch and put them in the trash container little by little until they are all gone .
  29. K

    Best Approach for Whole House Wiring?

    I didn't build this house, but I would have added more wall receptacles. I don't think one can have too many. One thing the person did that I do like is they used 12/2 wire throughout the house which I find great ! All 110V 20 amp circuits
  30. K

    Installing a hot water booster heater versus hot water recirculating setup

    I also added a small 110volt water heater in line .By the time the hot water has run out, the hot water from my tankless has arrived. Pipe hot water into 2.5 gallon from my tankless, and hot out to my bathroom works great !
  31. K

    saw this guy for sale locally

    https://www.facebook.com/marketplace/item/1047404000750261?ref=browse_tab&referral_code=marketplace_top_picks&referral_story_type=top_picks
  32. K

    Health Care Prior to Medicare?

    A google search found this answer.....(No, you don't need to have creditable insurance coverage before you can get Medicare coverage)
  33. K

    Why the name Gulf of America makes sense

    Biden thought what he did would stop any drilling. Trump got around what Biden did so we could resume drilling. Biden changed most of not all the names of the U.S. bases just to please the liberals. I have no problems with changing all the names back to what they were
  34. K

    Something you want but can’t get or afford.

    friend of mine up the road has a 4010 that also grinds when putting it into high gear !
  35. K

    Are CUT Manufacturers pricing themselves out of the market?

    Usually when someone finances, They also start financing other items like box blade, disc, etc, then they add insurance to the monthly payment. I have bought much better box blades and disc than the dealer is pushing
  36. K

    Something you want but can’t get or afford.

    it's gas I looked at the diesel in the fxt models and they don't run any faster than mine. It had a little over 1600 hrs on it. Just had the dealer replace the belt and a new shift cable.. Does your's grind a little when going into high gear ? Every one I have seen grinds a little (whit age)...
  37. K

    Something you want but can’t get or afford.

    I also have a 2012 4010 trans. I'm going to sell it since I bought this new one with 1000 cc engine. It's hard to chase cows with a 4010 that will only run about 23-24 if you're lucky ! LOL
  38. K

    Excavator size for farm work

    You better not send them a deposit to hold that machine, You just may lose that deposit. The machine you posted will cost more than 22K... My 2018 Takeuchi TB 235 was 25K
  39. K

    Excavator size for farm work

    I recently bought a 2018 Takeuchi TB235 hyd thumb with 1800 HRS not long ago. I bought this size because I wanted something I could transport with my 14K trailer. I also looked at a TB240, and I would have been ok with my trailer, but the TB240 goes up in engine size and has DPF which I didn't...
  40. K

    Your last generator Maintenance Run

    anyone know why they changed from a poly gas tank to an all steel tank ? I have an older Generac (B&S) engine, and it has the poly gas tank, which in my opinion is better than the steel tanks . No rust to ever worry about . I like the looks of the Predator, I'm just not sure about long term...
  41. K

    Something you want but can’t get or afford.

    Don't know if I can afford it, but I bought it anyway 🤣
  42. K

    Buying into the stock market

    Yep. But for those that continue to put off investing (and I know many) they wake up and 20 years are gone before they know it ! LOL
  43. K

    Buying into the stock market

    the time to invest in the market was yesterday.. Having said that, I suggest to Invest in low cost index funds.... Vanguard VOO comes to mind .
  44. K

    What Roth IRA have you had a good experience with?

    I like the Fidelity FXAIX fund as well
  45. K

    2024 Kawsaki mule pro fx ranch edition 1000

    I've only had the lexan type on my 4010 trans mule, which I'm going to sell. Unless I find a different brand, I'm most likely going with the fortress brand for my new mule
  46. K

    2024 Kawsaki mule pro fx ranch edition 1000

    Looks like a mule 610 or 40 10 Like the mule I'm replacing with this new one . my old one is a 4010 trans 6 seater . Kawsaki dealer doesn't have a real glass windshield. I've been looking at the fortress brand @ $1400.00 It's a real nice windshield
  47. K

    2024 Kawsaki mule pro fx ranch edition 1000

    my old mule will only run 24 -25 mph. I needed something a little faster as I have to go on the road with it sometimes . It will be a work mule. not a toy here. I was going with a diesel, but the top speed was about the same as my old mule
  48. K

    Something you want but can’t get or afford.

    Well, I myself, my siblings came from parents who's moto was, '' If you can make (afford) the payment, buy it'' mentality. It doesn't matter what the interest rate is. It was very hard for me to over come this mentality. Many don't know, I quit school at the ripe old age of 15 to go to work...
  49. K

    Something you want but can’t get or afford.

    I can assure you, You aren't the only one to ever be stupid with money. I've done plenty of stupid with money !
  50. K

    Something you want but can’t get or afford.

    Just bought a new Kawsaki mule pro fx ranch edition Friday. I would have never been able to write a check for thar much money bake in my younger days
  51. K

    Something you want but can’t get or afford.

    I usually just go buy what I want / need . I would love to have been able to do this when I was in my 20's instead of now in my late 60's
  52. K

    2024 Kawsaki mule pro fx ranch edition 1000

    Yes, I plan to remove at least the driver door on mine
  53. K

    2024 Kawsaki mule pro fx ranch edition 1000

    what model is yours ? I'd be interested to see/ know which windshield you added to yours, and find out of it will also fit my mule I'm not going to buy another lexan windshield, they just don't last
  54. K

    2024 Kawsaki mule pro fx ranch edition 1000

    your ranch tops out at 35 ? I test drove this one, and I know it will run at least 60 !
  55. K

    Something you want but can’t get or afford.

    neither will be any cheaper than they are today.. I went yesterday and bought a new Kawsaki mule ranch edition. . I really didn't want to spent that amount of money on that thing, but I figured they'll never be any cheaper than they are right now. I have bought brand new vehicles cheaper than...
  56. K

    2024 Kawsaki mule pro fx ranch edition 1000

    I gave 19K OTD. Don't know if that was a good deal or not lol
  57. K

    2024 Kawsaki mule pro fx ranch edition 1000

    Just purchased a 2024 Kawsaki pro fx ranch edition 1000. does anyone else own this model ?
  58. K

    Diesel fill

    Then they're all Ballsy around here ! LOL
  59. K

    Diesel fill

    I've seen many fill their diesel trucks with off road diesel to save the fuel tax. The store clerks don't care what you doing at the pumps. they usually busy waiting on people buying things in the store to worry about what you're pumping
  60. K

    Just Bought a Tandem Axle Trailer

    I bought a bumper pull. My 07 Ram 2500 pulls it just fine with my Kubota MX 5100 loaded. I'm not even gonna try to load my CX105 on that trailer
  61. K

    Just Bought a Tandem Axle Trailer

    I bought a 14K 24 ft trailer last yr $5500.00 new. Have no idea what they going for these days
  62. K

    Triple A (road service) rant

    I know people that had AAA, but after spending hours on the side of the road waiting on AAA to change their flat tire, they are no longer members. I have also known members that sat waiting for hours for a jump off as well. You'll what you need from them at their convenience, not yours !
  63. K

    which insurance plan to chose ?

    I keep my income under that threshold, so I only pay the part B min. I believe $187.00 per mo.
  64. K

    Investments strategy with new administration?

    I use and have used a CFP for since I sold my business and just retired ! They use BYN Mellon as the custodian . I'll likely continue to use this firm as they set up my trust, and they also file my taxes every year, so they're a one stop shop for me. They also offer me the option of investing in...
  65. K

    which insurance plan to chose ?

    I have never heard of a supplement that can be used as an advantage plan. And why would you want it to be used as an advantage plan ? You either have an advantage plan, or a supplement plan. You can check out all plans available on medicare.com, or watch the videos on medicareschool.com
  66. K

    which insurance plan to chose ?

    but with a supplement, you won't have to worried about if you're covered or not. If Medicare covers it, your supplement has to pay. You can always switch to an advantage plan, but depending on what state you live in, you can't always switch to a supplement plan. You can also go to medicare.gov...
  67. K

    which insurance plan to chose ?

    Advantage plans are contracts that can and do change from year to year. They are more geared for your specific area. If you travel, they may not be accepted if you should happen to need to use a hospital, or see a doctor. Medicare and a supplement follows you and pays the same no matter which...
  68. K

    Cattle questions

    I also have one strand of electric ... this is the charger I have...
  69. K

    Cattle questions

    I have seen calves walk right through widely spaced barbed wire. I have helped several neighbors catch calves and get them back in the fence. They learned to place the strands closer together. Better to do all you can to prevent them getting out to start with, than to have to be out on a cold...
  70. K

    Cattle questions

    I think I read you were going to run 4 strands of barbed wire ? I really don't think 4 strands are going to do it, But you'll find out whether it will or not. I run 8 strands myself . keeping a few low to keep the calves from just walking through the wire . You also mention storing hay outside...
  71. K

    An uncomfortable conversation. Don't suffer in silence! Embarrassing!

    I believe all dermatologist are women. I've met a male dermatologist. Anyway, I had this rash I just couldn't shake. Made the appointment and I really didn't want to drop everything right there in front of them both (doc, and assistant) but I was at wits end, and this rash was driving me NUTS...
  72. K

    Cattle questions

    I believe that's the case in many areas. I personally know 3 vets that refuse to do large animals. For one, they can make much more money on dogs and cats. And two, they are less likely to get seriously injured with a dog or cat.
  73. K

    Cattle questions

    Talking about birth weights. This is the reason for purchasing a registered bull. You know it's history of birthweight . Right now, I'm using a Hereford bull with angus heifers / cows, and Hereford heifers /cows, but I have also used Angus bulls on Hereford heifers/ cows. I had zero issues...
  74. K

    Cattle questions

    I raise Hereford / Angus cross. Last week at the stockyard, 600-700 # steers ranged in price from 1.60- 2.67 per # Bottle calves are tough to raise. some make it, some don't. I usually raise my beef to at least 1300# before I take them to the butcher. The steaks and brisket are much larger.
  75. K

    which insurance plan to chose ?

    He explains The differences between all the plans very well and in detail. I finally chose Humana supplement N plan over G. Figured I would save money and self insure just a little
  76. K

    Would you donate?

    No mention of insurance or not. If not, they hedged their bets and lost.. If they couldn't afford flood insurance, they should have sold out and built out of a flood plane . Churches are tax exempt. They should have placed that money in an account for a rainy day.. I see people all the time...
  77. K

    Recommend me a dash cam

    I installed one in my toyota highlander. It looks like a factory install It installs around the rear view mirror and plugs into the current wiring . You don't even know it's there. You didn't mention which vehicle you have . here's the one I purchased...
  78. K

    Auto insurance dilemma for a minor

    One thing I forgot. Here, a minor isn't allowed to enter into a legal contract either.. a loan for a vehicle, or any loan from a bank, etc,. where there is a legal contract involved
  79. K

    Auto insurance dilemma for a minor

    Only makes sense...I had (and still do) have too much to lose without it Hit someone, and total an expensive car and or seriously injure someone, and if you don't have enough coverage, you're SOL !
  80. K

    Auto insurance dilemma for a minor

    21 here to buy alcohol and tobacco products too !
  81. K

    Auto insurance dilemma for a minor

    I guess that would depend on the level of coverage selected. A broken neck would cost a lot of money. Some people have low limits of uninsured/ underinsured coverage. Here, you can waive that coverage if you want. I have seen some with only a 25K limit. That isn't going to cover very much When...
  82. K

    Auto insurance dilemma for a minor

    19 in Alabama, Your state may differ IDK
  83. K

    Auto insurance dilemma for a minor

    It's my understanding , age of majority is different in every state ? its 19 here
  84. K

    Auto insurance dilemma for a minor

    A minor is only allowed to work xx hours. Have to be an adult to have a vehicle titled in your name here. ''Land of the free'' ya know >> LOL That same minor works, pays taxes and isn't allowed to purchase a gun, tobacco,and alcohol... too so ???
  85. K

    Trenching downspouts

    I just did the same thing you are doing. I used my mini ex for the digging and back fill. Had to do a little dress up with a rake
  86. K

    Auto insurance dilemma for a minor

    So in that state, a 16 yr old (minor) is allowed to purchase a car and have it registered in their name ? Here, a car can't be sold to a minor, the car has to be registered in an adult's name. So here, since the car is registered in the adult's name, the insurance also has to be in the adult's...
  87. K

    Garage Car Lift - Atlas 9KOHX - 9,000 lb 2-post

    If you watch some of the auto mechanic shows on motor trend tv, they use Bendpak brand lifts. I have noticed on those shows that some if not all of the Bendpak lifts use a chain where my Forward (by Rotary) lift uses only cables no chains. you can google the differences if you haven't done so...
  88. K

    Garage Car Lift - Atlas 9KOHX - 9,000 lb 2-post

    I don't know the actual model number, but it's a 10K 2 post lift by Forward. Like you, I was looking at an Atlas brand. At that time, Greg Smith out of GA. was the distributor for Atlas equipment. Same place I had purchased my tire machine from. I have a couple of friends that have auto repair...
  89. K

    A really good flashlight

    I have purchased several flashlights over the years. The latest and Best I have ever bought is the knuckle head flashlight . It has a magnet at the base and will stay where ever you place it. the head swivels 360 deg, and also up and down. I wish I had known about this light years ago working on...
  90. K

    Garage Car Lift - Atlas 9KOHX - 9,000 lb 2-post

    started to pull the trigger on an atlas, but got a deal on a Forward 10 K lift. Only draw back of 2 post lifts is, It takes time to get the arms set right before you lift.
  91. K

    Since the Election........

    I sold out my business at a great time !
  92. K

    Propane direct vent shop heater

    there may be some dust clogging up the burner venturi . Blow out with air. Propane usually burns more yellow than does NG though . Just replace the thermocouple if you have no way to check millivolts in circuit, or out of circuit . You may also need to clean the pilot as you may have dust in the...
  93. K

    Battery Jumper

    that's odd. My son has noco brand and when the battery in my tractor exploded, We used his to start the tractor to get it up to the shop
  94. K

    Propane tankless water heater

    I clean mine every year and I'm not on well water. When water is heated, those minerals will separate from the water and attach it's self to the water coil. I've seen too many stopped up water coils, so I just play it safe. and it doesn't hurt to clean it once a year that I'm aware of
  95. K

    Propane tankless water heater

    Yes..... I installed a 5 gallon 110v electric WH in my crawl space just for that reason. The hot piping from the tankless goes to the inlet side of the 5 gallon elec. WH, and the out side is piped back into the hot water lines to my master bath. This way, about the time my 5 gallon 110v elect...
  96. K

    Propane tankless water heater

    another thing is. Make sure the one you purchase comes with flush valves. some do and some don't. You'll need these when it comes time to flush the WH
  97. K

    Propane tankless water heater

    most of these tankless burn 199,900 BTU. If that's the one you purchase. make sure you have plenty of supply /volume to handle that many BTU. depending on distance, 3/4-1'' black iron gas pipe. You'll be burning on 11'' WC with the propane
  98. K

    Propane tankless water heater

    inlet filter will help some. But as the water is heated, the minerals that are in the water will separate from the water and attach it's self to the water coil. You may have to flush the coil more than normal to prevent total blockage of the water coil. I have attended several classes where...
  99. K

    Propane tankless water heater

    tankless will not use the same type, or size vent
  100. K

    Basement Drain Repair Question - Need Advice!

    is this just a floor drain ? Where does the drain terminate ? what is the drain material ?
  101. K

    What's Your Opinion on Duct Cleaning?

    talking about the condensate drain , or your condensate pump. there are a lot of HVAC systems installed in the attic here. No where else to put it with a slab built house
  102. K

    What's Your Opinion on Duct Cleaning?

    if your squirrel cage is clean. your filter is doing it's job of containing most of the dust and dirt being sucked back through the return and re distributed in your home. Of course your A/C will catch some of it, but after the A/C coil there's nothing but duct work and insulation and nothing to...
  103. K

    What's Your Opinion on Duct Cleaning?

    Main duct work is usually insulated on the inside. your run supply to each room is either flex, or metal insulated on the outside. I have never known of round metal supply run outs to each room insulated on the inside. Some older homes had square metal supply ducts to supply each room, and I've...
  104. K

    What's Your Opinion on Duct Cleaning?

    A lot of times you'll know how bad your duct work is just by looking at the squirrel cage on the on the blower motor. If Those fins are caked with dust / dirt, your duct work is most likely caked with dust /dirt as well.. It's best to have all the cracks and seams sealed up on the return side...
  105. K

    Can a mini do the ground work to build home - slab or piers?

    I have a Takeuchi TB 235 and I wouldn't want anything smaller that that. I may trade next yr for something larger
  106. K

    What's Your Opinion on Duct Cleaning?

    I'm going to guess you're talking about flex ? So, your ductwork is duct board and flex ? Replace it with metal and insulate on the outside. I'm not into breathing insulation fibers. I started insulating metal duct work on the outside some 15-20 yrs ago
  107. K

    What's Your Opinion on Duct Cleaning?

    If you got all that crap in your duct work you really should consider sealing all the air leaks and using a quality filter. Been doing this a long time and I've seen just about everything. Now if the previous owners of the older home had not used a good filter, has air leaks in their system...
  108. K

    What's Your Opinion on Duct Cleaning?

    If you use a filter, you shouldn't have any, or much crap in your duct work. If your duct work is insulated on the inside, it's a bad idea to have them cleaned. I would just replace the duct work and have the ducts insulated on the outside . You are breathing more insulation fibers than you are...
  109. K

    PEX crimp tool?

    all I use anymore is pex and here's the tool I use...
  110. K

    Buying ammo. Take inventory first!!

    compromise, is better than losing my Right to live free-er lol
  111. K

    Anyone here donate Real Estate for charitable deduction and how did it work out?

    The reason I hear many are getting out of that country. I know two that just moved from there all the wat to Mississippi. LOL.. Said they were tired of all the regulations
  112. K

    Question on FICO score

    That's interesting... I have no idea what my FICO score is. I don't even know when the last time it may have been checked
  113. K

    Buying ammo. Take inventory first!!

    last ammo I ordered (223 rounds) I ordered 10,000 rounds @ 33 cents per round. I probably have 7K rounds left this was pre covid
  114. K

    Heating 12 by 20 Insulated Shed

    I wouldn't use a kerosene heater unless it's ventilated area
  115. K

    Is there a plumber in the house? (Stuck stopcock valve)

    Yes, it does. I've made a lot of money in the plumbing and HVAC business . Can't really figure out why people want to call a Plumber, but I'm sure glad there are those type people that exist .. LOL
  116. K

    Is there a plumber in the house? (Stuck stopcock valve)

    replace them all with 1/2 turn stops .. You'll thank me later
  117. K

    Unknown tool?

    valve core remover/ installer . It will do both
  118. K

    Electric fence advice

    I don't know how a .15 would shock but I can tell you that 32 feels like you stuck your hand into 240 volts ! I was bent over close to the wire never thinking about it. I accidently raised up, touched the wire with my head, and it felt like someone hit me across the back of my neck with a ball...
  119. K

    Electric fence advice

    .15 joule doesn't seem like much . But if it works...... I guess mine is over kill @ 32 jouels
  120. K

    Fence Chargers

    I have this one Cyclops Boss, 32 Joule, 110V AC Powered Energizer | Free USA Shipping... It's been repaired twice in 7 yrs from being hit by lightening .. They are made not far from me and they repaired both times at no charge
  121. K

    Air Compressor.... which one?

    https://www.mile-x.com/belaire-418vl-7-5hp-208-230v-1ph-80-gal-vertical-two-stage-electric-iron-series-compressor/?gad_source=1&gclid=Cj0KCQjwsc24BhDPARIsAFXqAB0timM6LPYIJwtPaSpYafyk5AXn_YrxuFnYhvOxhq1mBg1OI8QdvDkaAryhEALw_wcB I have this one for several years now to operate my glass bead...
  122. K

    Two Post 12k pound vehicle lift

    I had my floor in my shop broom finished for this reason. You can get a concrete wheel for a 4.5'' grinder to rough up your floor somewhat to prevent it from being so slick when wet
  123. K

    Two Post 12k pound vehicle lift

    https://www.uniquetruck.com/product/35078/atlas-rj35-sliding-jack-3500-lb?gad_source=1&gclid=CjwKCAjw68K4BhAuEiwAylp3kkMS5JYbkIxo-pnugYRwvc7_ISuavugv7SErc7D9yuchSbuuhaN2hBoCFQUQAvD_BwE IDK if this specific one will work with your lift or not
  124. K

    Two Post 12k pound vehicle lift

    I have a 10K Forward lift Made by Rotary. I wish I had a 4 post instead. Lifting many different vehicles require you to position each vehicle differently. Always having to adjust to get the vehicle just right for the lift arms to go to the right spot. It's also a tight squeeze to get in and out...
  125. K

    Square footage per person in a residential home?

    I've worked on some old (converted to gas)coal burners back in the day. Steam and water boilers as well. Have gone on many calls where some people don't know the difference in steam vs water boilers, and flooded the steam boilers with water. Water would be coming out of the radiators . Some...
  126. K

    Square footage per person in a residential home?

    I noticed that window shaker !! I just couldn't resist ! :ROFLMAO:
  127. K

    Square footage per person in a residential home?

    Snow ? LOL mostly a dusting.. We get that ever once in a while. I believe this pic was a couple yrs ago . After selling out, I had to purchase something for tax purposes so I figured this old farm / house would be a good investment. Prices were low when I purchased this place.. And due to the...
  128. K

    Square footage per person in a residential home?

    Heck Joe, I live in this all by myself. I would think with 3 of you you would need more than 2000. But I guess it's all in what you want and think is large enough.
  129. K

    Part D prescription plan

    wow ! My part D plan only went up $3.00 per mo . for 2025. ($43.00 per mo) I feel lucky
  130. K

    Part D prescription plan

    you can also do this on the medicare.gov website
  131. K

    Propane generator regulator questions

    Yep, I just drilled out orifices for 3 propane fired furnaces due to the customer changing over to natural gas. Swapping them would be much easier than drilling them, then clocking the meter to make sure they were correctly fired
  132. K

    Propane generator regulator questions

    You also need to know if your tank regulator is supplying inches of wc, or psi
  133. K

    Propane generator regulator questions

    Assuming that regulator is adjustable, You would need to have the generator running and have your inches of wc gauge connected on the inlet, and then the outlet side of the regulator and turn in (clockwise) on the adjustment screw. Your manual should state what the supply pressure should be...
  134. K

    Propane generator regulator questions

    If the orifice is larger, It could supply too much gas and cause the motor to flood . Personally, I would stay with the factory recommended orifice
  135. K

    Propane generator regulator questions

    you can use an inches of water column gauge and check the supplied gas pressure from your tank regulator to this regulator while the generator is running. There should be a test port to allow you to check incoming gas pressure. That would let you know if the tank regulator is keeping the...
  136. K

    The accountant says we can retire early. Woohoo!!!

    hard to beat that compounded interest all those years !
  137. K

    Air Compressor Stalls Out

    check the amp draw on the motor while running
  138. K

    The accountant says we can retire early. Woohoo!!!

    I don't have all mine in the market .. I have some in private equities
  139. K

    Battery powered chainsaw

    Have been using my Ryobi Poll saw the las few days trimming the tree limbs back from the fence lines. The battery that comes with it is a bit small but I just change it out with my Ryobi chainsaw battery and continue on. By the time I kill off two batteries. I'm ready to stop and clean up all...
  140. K

    The accountant says we can retire early. Woohoo!!!

    as Dave Ramsey says.. slow and steady. The turtle wins the race against the hair every time ! LOL
  141. K

    Fence Charger Help

    I have this fence charger...
  142. K

    Korean tractor dilemma

    good luck. I bought and owned my one and only... Never again 1 quart of oil every 800 miles was just too much and they said that was considered normal ! LOL
  143. K

    Korean tractor dilemma

    I thought about buying a Korean tractor, until I owned a Korean vehicle ..
  144. K

    Importing and modifying a new mini excavator from China

    I agree, parts and some type of support may be a problem when a problem occurs. When / if I need a part for my Takeuchi, I just drive down to the dealer and pick it up. If something major were to happen, I can load it up and haul it to their shop for them to repair, or have them come here to...
  145. K

    Something Bigger

    you have limited swing with a TLB. A mini ex can swing 360 deg which is an excellent benefit over TLB.. You can't get it into some tight spaces like you can a mini ex. I just bought a Takeuchi TB235 with thumb, and love the machine. Sometimes, I wish it were a little larger but, I wanted to...
  146. K

    How do y'all feel about Frigidaire vs. GE vs. Whirlpool

    on the newer ones it's the hot surface ignitor and circuit board for bake, broil , etc,.
  147. K

    Have you ever thought about changing the central air conditioner?

    the warranty is only as good as the company offering it. Have seen many companies over the years offer up the moon, and when it came down to it only produced a box of rocks !
  148. K

    Part D prescription plan

    yes, I understand Advantage plans offer what they claim to be perks, but they come at a cost.. co-pays for surgeries, test (MRI's etc,) Hospital stays, etc,. If you go out of your home state, you may not be covered, or you may be out of network and cost you much more out of pocket. Also, as you...
  149. K

    Part D prescription plan

    I have Humana plan N .I pay $98.93 per mo. My part D is through Humana also which cost me $40.00 per mo. My dental is with Cigna @ $35.00 per mo. With my son being in healthcare, advised me to stay clear of any disadvantage plan
  150. K

    Have you ever thought about changing the central air conditioner?

    Then you're installing the wrong central H.P. Mine is as quiet as any mini split system out there and is ducted . All my duct is insulated outside, not inside
  151. K

    The accountant says we can retire early. Woohoo!!!

    One of my sons (youngest) manages a cardiology group, and has a hard time being able to repair, or do many of the things his older brother (paramedic) can do. His older brother always wanted to work with me in the shop. The younger one not so much. He always told me that he was going to make...
  152. K

    The accountant says we can retire early. Woohoo!!!

    congrats ! I got out of the rat race in 2015 @ 57. I'll still do some small jobs when I want, but nothing regular... I just don't have time to work anymore ! LOL I purchased a mini ex a few months ago so I make take on a few small jobs with the mini ex
  153. K

    Part D prescription plan

    When your government thinks they can tell big pharma what they can and can't do :ROFLMAO: :ROFLMAO: Every action has a reaction.. remember when they made it mandatory that your children can stay on your insurance until 25 ? Yeah, the insurance companies raised your rates to cover it ! Your...
  154. K

    Stove Pipe

    The installation instructions with the stove should tell you what type vent piping to use. I have always used what the manufacture recommends
  155. K

    I want a Hydraulic grapple for my L3130 with la513

    I have diverter valve on my large tractor and a 3 function on my MX. I'll take the 3rd function over the diverter any day !
  156. K

    Loader Hydraulic issues, No back Pressure after the Loader controls?

    If that quick connect coupler line is connect straight to the pump, and you disconnected that, and started it, You deadheaded the pump
  157. K

    Loud Popping from Excavator Track

    well I finally got around to loosing my popping track today. Hoping this stops the popping . We'll see when it dries out here
  158. K

    Electric fence advice

    If you can't go down the recommended depth, you can always add more rods. I have rock about 4' ft down, so I added a ground wire to my non electric fence for xtra grounding
  159. K

    Have you ever thought about changing the central air conditioner?

    GREE Electric Appliances Inc. of Zhuhai, China, is the world's largest manufacturer of air conditioners. Through eight production bases in China, Vietnam, Pakistan and Brazil, GREE can produce up to 27 million residential and 2 million commercial air conditioners per year.
  160. K

    Have you ever thought about changing the central air conditioner?

    Yes, Mine is a Gree VRF. with matching AH. Gree has come out with what they call Gree flex . While I haven't installed any, from what I've read, it works on the same principle as my unit. it doesn't require a communication wire and operates with any 24v T stat and T.stat wire. it will heat to...
  161. K

    Have you ever thought about changing the central air conditioner?

    yes, but mine doesn't have that feature. I do have the capability to install a Y on mine and run a head to say a bedroom, etc, But I just use mine as straight ducted system. I do like the continuous running for humidity removal, and the low HTZ it uses during operation . My home is way more...
  162. K

    Have you ever thought about changing the central air conditioner?

    I can't heat and cool different rooms at the same time with my ducted VRF unit. My brother installed different out door mini split units so he can heat one room and cool the other if he choses to do so. I don't know why he would want to do this but he did lol
  163. K

    Have you ever thought about changing the central air conditioner?

    If they replaced the unit with a VRF they would save money on their utility bills whether using heat, or A/C .
  164. K

    Have you ever thought about changing the central air conditioner?

    I have no idea what type system you're referring to but most all refrigerant is still available . (at a cost) If it's R12, there may not be any compressors to be had. but I'm not aware of any government mandates that require a full replacement due to the system being old and out dated
  165. K

    Loud Popping from Excavator Track

    mine does it on one side. I thought something boke. I have a takeuchi TB235. Doesn't do it all the time but when it does, it's loud
  166. K

    A very dumb question on Roosters

    there are several around me. They are most likely just breeding them and selling them. Here, there is no law/ restrictions when it comes to breeding and selling game cocks. Just the actual fighting of them
  167. K

    Have you ever thought about changing the central air conditioner?

    While I have no clue as to what system he has. He can save on cooling with a new inverter system such as a ducted VRF. Installing something such as a Gree Flex (or similar) would be a great upgrade for Cooling and heating
  168. K

    Generac or Koehler whole house generator?

    I haven't made up my mind to get one. My power rarely goes off and when it does, it's back on pretty quick. Last time it went out, the transformer went out at the pole. They came out to check within an hour. Said they would have to send out a larger truck with a transformer. I was thinking 2-3...
  169. K

    How best to dam a creek?????

    yeah, all I did was to call the county agent as to get advice as to how to go about building a pond, and thought it would be a good idea to just damn up the creek. Glad I did call instead of just damning up the creek. I imagine they always looking through google earth to see what people are...
  170. K

    How best to dam a creek?????

    I was going to damn one on my property and the county agent told me it wasn't allowed. showed me a map with a blue line indicating the creek...Said see that blue line ? Yeah so ?? the Army Corps of engineers controls that creek, and that you'll be finned for for damning up the creek, and made to...
  171. K

    How do y'all feel about Frigidaire vs. GE vs. Whirlpool

    I will suggest what ever you have that's been working for 10 yrs, you may want to keep it. I guarantee, that unit will last longer than what you'll get today. This government is mandating higher and higher efficiencies and the consumer is paying the price with inferior appliances, that doesn't...
  172. K

    Land Pride RTA1274 not the best choice?

    I just purchased a new IRONCRAFT 6' tiller. This thing is heavy. I chose it over some other brands due to it being heavier build. So far, I love it ! I paid 2595.00 for it
  173. K

    Ignore List

    LOL !!! I guess we do !! My friend .
  174. K

    Ignore List

    none.. I'm not that soft
  175. K

    Current deal at Harbor Freight

    YES, I forgot .. I also have Makita drill and impact. I just purchased a Ryobi right angle drill !
  176. K

    Current deal at Harbor Freight

    While I would love a batter operated grease gun. I have many Ryobi tools, and would hate to have to purchase a different battery operated tool. The Ryobi grease gun is also $139.00
  177. K

    Ironcraft tiller

    I just purchased this tiller and it is really heavy built ! It does a very good job of tillering up virgin soil !
  178. K

    What Caused This Wood Deck Failure?

    I have several of these. Problem is, they fill up in no time. I have found it works best for me to spray the wood with high yield 38
  179. K

    Too much work !!

    Well, I'm not your age, but I use to have no problem grabbing a shovel and digging a trench for anything, like a drainage pipe, etc,. Well, as I get older, I figured I'd get some help. So like you, I spent some of my kids inheritance, and purchased a mini excavator to dig those trenches and...
  180. K

    Rock Auto - now impossible to communicate with.....

    I have only ordered a couple of times from rock auto. I called once and ask a question about a part I was interested in purchasing. The person that answered the phone basically told me they had no idea about said part, and all the info was listed on their site. I never ordered another part from...
  181. K

    What Caused This Wood Deck Failure?

    That treated wood seems to attract those bees, while they don't seem to bother regular wood in my barn !
  182. K

    What Caused This Wood Deck Failure?

    I doubt you actually did anything that caused it. Treated wood today just doesn't last. I'm finding yellow wood doesn't last as long as other brands of treated wood. I have some yellow treated wood on my deck that has rotted, while treated wood of a different brand (from Lowes) is still good and...
  183. K

    72” vs 84” Tiller

    I just bought a Iron craft 6' tiller for my MX 5100 HST and it's all it wants
  184. K

    Tiller pulling dirt

    I just bought a new 6 foot tiller. I was talking to the guy about a reverse tine and he said the same thing you are experiencing . I opted for the forward rotating tine tiller. I have been pleased with it. Well built too !
  185. K

    Medicare Plan G

    I have no idea how zip codes play into the price.. My N plan started out @ $92.00. Had an increase this year to $96.00. My drug plan which pays for almost everything I have needed is $40.00, and my dental plan (optional) is $35.00 per mo
  186. K

    Medicare Plan G

    medicareschool.com has some very informative videos that could be worth watching if you are new, or soon will be on medicare. Talks about the advantages of supplements vs Advantage plans
  187. K

    Medicare Plan G

    I believe it depends on your zip code and other things such as no underwriting for coverage, etc,. A plan G for my would have been $150 per mo so I opted for the N @ $96 per mo. and will self insure for the small deductible, etc,. Went to the dermatologist today and it cost me $20 for my visit
  188. K

    Medicare Plan G

    If you on straight Medicare, you paid 20% of the total charge. Medicare only pays 80% and unless you have a supplement , you are responsible for the other 20% Having said that, I have a Humana supplement N plan. I've been pleased with it. $96.00 per mo where I live
  189. K

    Anyone here own a Takeuchi mini ex ?

    I wanted a TB240. More HP and little more weight, But @35 hp you have to deal with DPF. It's a shame they mandated DPF on 35 HP. I don't like any of it, But the cut off point could have been @40-50 HP range
  190. K

    Anyone here own a Takeuchi mini ex ?

    I just picked up a used one 2018 mod with 1800 hrs. seems to be a good machine for the money. TB235
  191. K

    EA grapple not an option now what?

    I'm intelligent enough to know when I receive excellent customer service. It's obvious that EA hurt your feelings at some point. Did they do anyone wrong ? I have no clue, I haven't seen any post where they wronged anyone that owns a EA grapple . People that did break parts were sent new parts...
  192. K

    EA grapple not an option now what?

    And all I know is how they treated me, and they didn't have to ! They could have said, sorry, no warranty !
  193. K

    Car Insurance skyrocketing

    Travelers, liberty mutual, Safeco, etc, are hardly small LOL. It really isn't marketing hype. they actually saved me over a captive agent. I have had superior service from Travelers . To each their own, but everyone should do a little research on Independent agents. A little education could...
  194. K

    EA grapple not an option now what?

    only if it's a Kubota :ROFLMAO:
  195. K

    EA grapple not an option now what?

    funny, they never did that to me when I had a bolt failure that broke part of the grapple. I shipped it back at their expense, they made repaired, and shipped it back at no charge ! I never was ''ripped''
  196. K

    Yanmar 336D front loader hydraulic issue

    could also be rust, etc, in your loader valve if it sit outside for years
  197. K

    Car Insurance skyrocketing

    If people would use an independent agent rather than a captive agent, you would have a much better chance of lower rates. My independent agent will shop other companies he represents when my rates increase. I don't have to bother calling around wasting have a day, or more shopping rates
Top