My NX6010

   / My NX6010
  • Thread Starter
#401  
Are you getting another box blade or are they going to beef this one up?

Travis talked to me about a credit, but I'm certainly willing to get the same blade back or an updated blade. What I can say is that Everything Attachments is being really good about it, and as I said earlier, and this entire thread testifies to, we're all learning.

What I can say is that after Thanksgiving, I'm shutting the lake home down, and with it land developing, because heating two homes in a Minnesota winter gets stupid expensive and can lead to unforeseen problems.

399129d1416272371-my-nx6010-winter5-jpg


Which is to say that I will not need a box blade until spring.
 

Attachments

  • Winter5.jpg
    Winter5.jpg
    43.4 KB · Views: 891
   / My NX6010 #404  
Travis talked to me about a credit, but I'm certainly willing to get the same blade back or an updated blade. What I can say is that Everything Attachments is being really good about it, and as I said earlier, and this entire thread testifies to, we're all learning.

What I can say is that after Thanksgiving, I'm shutting the lake home down, and with it land developing, because heating two homes in a Minnesota winter gets stupid expensive and can lead to unforeseen problems.

399129d1416272371-my-nx6010-winter5-jpg


Which is to say that I will not need a box blade until spring.


Is that a 911 on the right?
 
   / My NX6010 #405  
Looks like the sprinkler system worked.
 
   / My NX6010 #406  
Bends in metal are way stronger than a straight piece of steel. Deere has been known for years to use bent metal to make stuff stronger. Looks like EA should be able to fix this issue easy out of heavier material. They may also choose to harden the metal some as on construction equipment to make it stronger in high pressure areas.
 
   / My NX6010 #407  
You need to find an older gannon blade that has the teeth that fold up or down, can be hyd or manual. YOU WON"T BREAK IT

If anyone could break it, it would be Eric. I hate to think what he would do to my little CK and TSC grader blade:eek:
 
   / My NX6010 #408  
To me the break in the shank looked like a stress fracture rather than a shear or tension failure. Might try some 120,000 stainless rod and welded it up, I have used it to repair drawbars etc. and have had pretty good results(luck).
 
   / My NX6010 #409  
Eric may be rough on his tractor, but what happened the the blade was not his fault. Not knocking where he bought it but somethings wrong in the metal
 
   / My NX6010 #410  
Travis talked to me about a credit, but I'm certainly willing to get the same blade back or an updated blade. What I can say is that Everything Attachments is being really good about it, and as I said earlier, and this entire thread testifies to, we're all learning.

I'm sure they will revise the box blade and make it stronger at the rippers.
 

Tractor & Equipment Auctions

1998 Ford F800 2,000 Gallon Water Truck (A49461)
1998 Ford F800...
2003 STERLING ACTERRA 11FT FLAT BED (A51222)
2003 STERLING...
2017 PETERBILT 579 TANDEM AXLE SLEEPER (A51222)
2017 PETERBILT 579...
2013 LONE STAR TRAILER MFG. (A50854)
2013 LONE STAR...
2019 Ford F-450 Crew Cab Mason Dump Truck (A50323)
2019 Ford F-450...
2018 JOHN DEERE 204L WHEEL LOADER (A51242)
2018 JOHN DEERE...
 
Top