Another John Deere 1050 hydraulic problem.

[krisbodean85]

im sorry but i dont really understand the question sorry. but right now there is 4 lines that run to the fel and 3 that run back to the tractor

 

[Rock knocker]

im sorry but i dont really understand the question sorry. but right now there is 4 lines that run to the fel and 3 that run back to the tractor

Sounds correct

 

[Rock knocker]

Is the three point working via the lever beside the seat and not being affected by the loader controls

 

[krisbodean85]

No the 3 point hitch is not working neither. I took my hydraulic pump apart to look at the seals to make sure I didn’t blow one. As I looked where the 2 gears are riding there is scarring around the walls. Could this be a reason why?

 

[beenthere]

Don't recall, but have you checked the hyd pressure yet? to know what psi you are getting and where you get it?

 

[krisbodean85]

No I haven’t I don’t know what all is needed to do the test and where to do it. And what it needs to read. A guy I know that use to work for John Deere said it maybe the relieve valve I don’t even know where it’s located and how to tell if it’s bad. John deer quoted me 800 for a new pump. I think I’m going to be sick. I have so much invested in this tractor already.

 

[krisbodean85]

that’s what it looks like inside the pump housing

 

[krisbodean85]

It’s just on one side

 

[krisbodean85]

well back to square one the pump came in and installed still doing the same thing. hoses are routed right to the joystick control valve . I think something is wrong with the joystick control valve its self possibly letting fluid bypass. Its starting to get very frustrating almost to the point that i just want to take it john deere and let them fix it

 

[Rock knocker]

I actually it's the rock shaft control valve. There's a thread somewhere here that explains what a gremil this part can be. Here is a Hoye photo of it
HYDRAULIC VALVE ASSEMBLY - NEW CH197 - OUT OF STOCK- CALL FOR USED: Yanmar Tractor Parts

 

[krisbodean85]

can the 1050 be hooked up back like it was without a front end loader? does anyone have a pic on how it hooks up? if i hook it back up like if it didnt have a front end loader i can eliminate alot of things to have to check and it would narrow it down to the joystick control valve

 

[Rock knocker]

How goes the battle?

 

[krisbodean85]

Well thought I would update on this headache I’ve had on this tractor for a long time finally solved the problem

 

[beenthere]

Thanks for that update. Hope all is working ok now. Been a tough row-to-hoe for you.

 

[Matt1050]

Hi . I’ve read through this thread. I have the same tractor 1982 JD 1050.

I want to eliminate the old two stick auxiliary controls and replace it with a joystick.

Did anyone get this set up working?

 

[beenthere]

Hi . I’ve read through this thread. I have the same tractor 1982 JD 1050.

I want to eliminate the old two stick auxiliary controls and replace it with a joystick.

Did anyone get this set up working?

:welcome: to TBN

Which setup are you referring too?

 

[Matt1050]

:welcome: to TBN

Which setup are you referring too?

The set up I知 referring it is using the 7 port Cross joystick valve body.

I saw the pictures and write ups but I never saw if he got it working properly.

This setup was to control the FEL as well as supplying hydraulics to the three point hitch still

In the mix I have power steering as Well

 

[Matt1050]

I’ve sent a pm to the gentleman who had the original questions on putting a joystick on his tractor.

Does anyone have any idea of the final results?

 

[krisbodean85]

its works awesome now. i replied to your pm