john deere 990

My John Deere 990 Compact tractor has a problem. It won't start. I was using it, stopped to do something and tried to start it again and nothing. The tractor made a small click but nothing else. I have a new battery in it. Cleaned the terminals, put in a new starter and ignition switch...

I recently purchased a 2002, 2wd, 990 with 774 hours. No maintenance history. I plan to change filters/fluids and alternator belt. Will appreciate any advice. The online manual I'm using doesn't mention the fuel filter under the fuel tank.

I have a John deere 990, 2003. Only about 600 hours on it. worked great until 2 days ago. Would crank just fine, but not catch. It grabbed a few times, but shut off in less then a few seconds. Acted like no fuel. Checked fuse box, fuel lines, changed both fuel filters, there is fuel in all...

Our JD 990 tractor is having some start issues, that have been traced back to the fuel solenoid. We're wondering if anybody has had the same problem and what the solution was. Turning the key draws the solenoid back and lets fuel go to the pump, turning it to start releases the pin and shuts...

My John Deere 990 4 WD makes a clunking sound when placed in 4WD. I visually inspected and see no obvious problem. The shift lever to engage the 4wd operates ok-no bind. I am attempting to remove the front drive shaft to inspect where it goes into the front differential. My technical manual...

John Deere 990 ran out of diesel fuel. Coasted off a bank and tried to restart. Cranked briefly then refilled with fuel. Started but had to bleed. Ran rough and discovered 1st cylinder closest to dash is not firing. All other cylinders are firing good. Removed and cleaned injector for that...

I thought I would share a solution that worked for me regarding my 990 not charging. Took the alternator apart and cleaned it with a toothbrush (was packed full of dirt). This was a very easy job and may need to be a regular maintenance issue, at least maybe every 200 to 400 hours. This type of...

Hello I have a JD 990. The PTO turns when disengaged. You can hold it from turning with your hand! Next is the PTO seal is leaking how hard of a job is this to repair? I hope it can be done from the outside. Thanks for any help!

I would like to know if there is a mechanical way bolt the loader arm to the tractor because I do not plan to take it off the tractor. Thanks for your help.

I have a 2004 JD 990. I am the second owner and have had it for about 13 years. I put about 2 hours a month on it mowing a 1 acre pasture and putting out (3) hay rolls every few weeks, it's total hours are 650+/_. About 7 years ago I had a mobile guy come out and replace something regarding the...

If I manage to get my John Deere started it will run perfectly until I turn it off and then try to restart. Then starter will not turn to start engine. Looking for anyone who may have had the same problem and what was needed to solve problem.

I am toying with the idea of switching from a rear scraper blade to a front mounted snowplow. What I am stuck on is, I feel a frame mounted plow would be better than a plow mounted on the FEL due to constant “racking” pressure on the FEL arms. But what I am finding is that there are very few...

I easily started up my John Deere 990 tractor and drove across a field. I killed the engine as I worked to place a chain around a fallen tree. Then when I got back onto the tractor it would not start. After towing it back to the barn I visually checked the different safety switches for...

My John Deere 990 won't start unless I put a jumper from the positive post on the battery directly to the starter....Then it starts and runs fine. I assume there is a blown fuse in the mix but can't find it. Any suggestions would be appreciated.

Ok I started out mounting a koyker loader on buddies 990 and only way I could get it to work is raise 3pt hitch up close valve off to closed center which it kills rear lift but the loader works fine open the valve back up kills loader but lift works so what am I doing wrong how can I get both to...

anyone deal with the jerky issue on the 990? the bucket, when i want to lift, goes down for a second then goes up ... i am thinking a leak or suction issue ... i would rather fix it myself than take it to the stealership a while back a branch tore the hydrualic filter assembly apart...

I wanted to join to tell anyone with a John Deere 990/790 tractor mfwd to maintain the drive shaft with grease every so often Read my post Thanks

Needing some help on my 990. For some reason the crankcase is filling with Diesel. Drained nearly 2 and a half gallons out today. Where could it be coming from? Any help would be greatly appreciated.

Hey there guys, new to this site and first post. I have a John Deere 990 I need to add rear hydraulics to because of an implement we just purchased. Everywhere I've called doesn't sell a kit anymore for the 990. Said they've been discontinued awhile now. Im not sure where to even start for...

Hey there guys, new to this site and first post. I have a John Deere 990 I need to add rear hydraulics to because of an implement we just purchased. Everywhere I've called doesn't sell a kit anymore for the 990. Said they've been discontinued awhile now. Im not sure where to even start for...

Hi Guys, long term lurker, only posted a few times if any. I'm looking for some help. I've got a 2003-2004 990 that has served me very well. I figure being 13 years old at this point its time to give it a little loving. I am looking for a grille (front and both sides). I use this tractor...

A friend of mine has a 2006 or so John Deere 990 and has never serviced anything other than the oil and filter. I know its way overdue so trying to help him out. Anyway, i've changed coolant, air filters etc but am now on the fuel items. So after looking at the manual it only mentions a rear...

Hi Guys, My buddy's 990 with 312 hours stored in heated garage won't start. Put in a new battery and removed dash panels, key switch and all wires are connected. Cleaned ground, removed starter and had it tested-they said it was fine. Put back in and just a loud click. Hook starter directly...

Hello everyone. Just installed the scv on my tractor that didn't have one on 2003 JD 990 170 hrs. Trying to put loader on with no pressure to cylinders. If I move the rockshaft control up and down at the same time holding the scv valve in any direction then the loader will move a little. What's...

Would you be afraid to buy a 2007 model tractor with just 15 hours on it?? I'm not considering buying this by any means (especially at his asking price of $15,200!), but this tractor has done a LOT of sitting in the shed. While it looks brand new, I just wonder if that much sitting is "bad" for...

We have a John Deere 990 with 430 loader (2002 model I think) on the family cattle ranch (350 acres in west Louisiana), it is the smallest of 3 modern tractors (others are JD 6310, JD 7200). The little 990 gets a fair amount of use, particularly in the nicer weather months, lots of general use...

When I use my fel valve to the right so empthy the bucket on my jd 4700 and on my 990 there is a point that both sides get oil. I noticed when I was using a tree sheer with a 4" cylinder, small return od rod, on the ram, the cyliner first closes, but then opens after I mover the handle all...

Ok, its been a while since I was on here, but I broke the instrument panel glass on my 990 and now I'm trying to replace it. Unfortunately, I have to deal with what has to be one of the dumbest design decisions in tractors or automotive in general: a pressed on steering wheel. Someday I'll...

Delivered to my camp in Vt last Feb. There are 2 JD dealers up here that would not take my MF165 on trade. I found a 2004 990 with 960 hrs. on it down here in central Ma. and they said no problem. That old mf started right up afer sitting for 2 yrs. and drove right onto trailer.

Hey folks, glad to have found and to be a part of this forum. I live on 5 acres and the JD 990 is the perfect machine for this farm Boy. Bought it new in 07 a upgrade from the JD 970. The 970 was a good tractor, but the extra 5 PTO HP was well worth the upgrade. The best part is that the front...

I started noticing chattering when pulling the box blade under fairly heavy load, until today chattering started and the 4wd stopped working, then chattering got much worse. I found another thread "final post below"where a guy had an identical problem, he was somewhat vague about how he fixed it...

I spayed my jd 990 with a water hose, also on inside of the hood agains the dash. The tractor would not start anymore., waited one day 90 degrees and dry, Houston, no change, thought is was the battery which was 4.5 years old, changed it, found a bad connecters on positive side fixed all that...

Hello, this is my first post to the forum and I must say that there is a tremendous amount of great information on this site and in particular this forum. I understand that in order to add a WR Long style 3rd function valve I can enter into the output port of my loader SCV assembly and connect...

Hi Everyone, I was doing some routine maintenance on my John Deere 990 to get it ready for Spring. I changed the engine oli (JD Plus-50 II Diesel Motor Oil 15W-40) and filter (M806419). Then I changed the fuel filter (T111383) as the container looked dirty. The container was filled with...

Trying to decide on getting rid of massey ferg 240 for a slightly smaller / newer jd 990/4005. Massey ferg is old and doesn't have front end loader....990 seems to be slightly smaller and just a little less horse power but would have 4wd and front end loader..... help me guys......think I can...

Hi everyone. New to the site. I have an '05 John Deere 990. I'm looking to get a backhoe ASAP to dig a septic pipe trench. What backhoe's are compatible? I think the 8A is compatible, anything else? Bradco? Where do I get the subframe? And finally, I believe the previous owner had a rear...

Does anyone have any tips on what I could look for with reference to the following: I have a John Deere 990 Tractor. Almost everytime I try to use the bush hog, when I go to engage the PTO, the bolt pin shears. Thanks

Im looking at this deere 990 John Deere 990 Diesel 40 HP Tractor - 2004 10 acres with 1.5 of "yard" but the fencing is reasonable and have alot of room even up to the house. I think this tractor is probably bigger than i "need" but i read they sip fuel so wth. Im aware of the gear/hydro...

JD990 with 250 hours is sluggish when I run in A2 or A3. It acts like the brake is locked on. Seems to not happen down in B or C.

JD tech says that this JD 8a backhoe can not be attached to a JD 990 with a 430 Loader ! I have the JD 8a with a 4" channel subframe but I do not see any attachment points on the rear of the tractor . Anybody have this combination installed ? Or do you have a JD 8b Backhoe installed and can...

Hello, the dealer told me to replace the flasher relay (already checked fuse). One person at the dealership told me I could find the relay by the fusebox under the hood. When I couldn't find it there, another call to the dealer and was told to remove the cover by the ignition switch and I...

hello all im thinking of trading in my 990 with bh for a 5055e with a loader. my 990 is a 1998 model 257hrs i primerely use it for some snow plowing clearing some land and loging fire wood out of the woods to heat my house about 4-5 cords a yr. the maine reason im considerind the trade is i hate...

Hi; I have a JD 990 compact tractor and recently had a throw out bearing failure. When we were doing the tear down I noticed that there are vent screens located on the sides of the bell housing that appear to me that they would allow moisture and dirt to get into the housing. Presume that...

My JD 990 hydraulics have started to lower much slower than it did when we first bought the machine. It has never had a hydraulic fluid or filter change. Is a plugged filter causing this issue? It raises fine, but lowers slowly with a 600# shredder is on it.

Hello everyone, I need a bit of help installing my W.R. Long 3rd function valve kit on my 990. I have the 430 model loader on my tractor and need some assistance in identifying the PB port on my loader valve. I think I should connect the Long provided P line to the connection in the picture...

I talked to two sales guys at two different stores I mentioned I may need a power beyond kit for a 4005, the sales guy said "is that a John Deere"? The other guy told me the 990 was an old tractor so I'd need to talk to parts... I had this ordered a week ago before I bought the tractor, today...

What would be the current model to a 990 2WD? Any differences in engines, trans, wheels/tires, etc? Thanks.

Hello all. I am new to this forum. I grew up with tractors and am now 51 and am looking at purchasing one. I own over 2 acres and it is wooded and has a lot of rocks etc. I want to build a barn. I burn about 6 cord of wood a winter. I have found a 2005 JD 990 MFWD with 300CX FEL, JD 8B...

I have a friend that has offered to loan me his Shaver HD10 post driver to drive some fence posts. I am not sure if my JD 990 has enough hydraulic flow to run the driver. Shaver web site says the HD10 needs 12GPM @ 1500 PSI. Specs on my 990 hydraulics say: Type: open center Capacity: 5.5 gal...

My dad bought a brand new JD 990 a few years back. Has anyone else heard of a problem with this tractor due to the design of the fuel tank? Last year I was mowing some brush on the side of a hill side, involving a lot of forward and backing up sideways on the hill. The hill wasn't all that...

I was torn between posting this under eBay/Craigslist or Is this a scam?.. I know it is a scam so decided to post under eBay/Craigslist. I have an orange tractor and really don't know much about these green things, but I know that I am not going to send money.... Good for a laugh. First email...

I have a JD 990 with an 8B backhoe. I have removed it and want to hook up a chipper. First of all I am not sure which hookups to use. At the back of my tractor there is a metal plate with 2 connections, the female on the left says "To Remote Valve". The right fitting says "From Remote Valve"...

I have a JD 990 with a fiberglass Curtis top. Can I safely trailer the tractor with the Curtis top on?

I am shopping for a compact tractor. I want a backhoe with it. I have been looking at some new (JD 2320 and Kubota 2320) but I am also looking at some used tractors. Used allows me to get a little more tractor than what I really think I need. I am looking at a 2000 JD 990 and JD 8B backhoe...

I have found a 1999 (2000 I think) John Deere 990 for sale with a 430 loader, backhoe, scraper, mower and snowblower. 1100 hours. He wants 20K. Thoughts?

Hi there, can someone help? My daughter was cutting the lawn on our JD990 when all of a sudden the engine began to cough and sputter and blow out a cloud of blue smoke. After that it ran for hours with no problems. This has never happen before. Is this something to be concerned about? Thanks

My friend just picked up a 990 4WD with a 300CX bucket and only 95 hours for a song. Sweet little tractor if you don't mind shifting. Rob

I was pulling a 9ft drag with my 990 in 4 wheel drive an noticed some noise from the front end. Four wheel drive stopped working now. This tracter has 175 hours on it. Never been on pavement an is clean. I dropped the oil in the front end only to find it is clean with no metal shavings...

Wrong section

I'm looking at a used JD 990 2008 40 HP, what are peoples experience with this tractor? It is has a 300cx loader and 8B backhoe. The transmission is 9x3 and it is non synchro with a Yanmar engine. Any opinions on the above specs is appreciated. Thanks

I have been out on the forum as a visitor "soaking up" knowlege from all of you for some time which has been great and I now need some help regarding purchasing a backhoe for my 990. This is the first time I have posted. I know that JD makes the 8B for my tractor. It seems that the Woods 80BH-X...

What a great forum! I have been reading and learning a great deal from everyone on here. Thanks. A very good friend of mine is selling a JD 990 and I would like help with two things. We were discussing price, and I want to make sure that we agree on a fair value. I do not want to take...

A couple weeks ago I called my tire dealer to order me a set of Galaxy Mighty Mow turf tires size 10-16.5 fronts and 17.5L-24 rears. Come to find out the Northeast has a shortage on the fronts. Just wondering if anyone has these and are there any ideas for or dealers to try and see if there are...

Hi, I'm looking to buy and these 3 tractors seem to be in the range of what I'm looking for. I'll be using it with a FEL to clear land, move rocks, clear snow, maintain some wood roads etc... My land is very hilly, about 60 acres of mostly woods. What are your thoughts on the good the bad...

Been while a since I mentioned I was getting my new/used 990 with 44 hours on it. Now that I have had some time to snowblow and use the loader I can not believe what a difference compared to my old 850 and my Father in Laws 1050. I hope to post some pictures in the next day or two. But here is...

I had the wheel almost all the way into a full right-hand turn when I stopped to chat with someone. When I powered up again, I can not turn the wheel to the left. It will turn the rest of the way to the right and then back to the "starting point", but that's it. As it is we're talking less...

I am highly considering buying a backhoe for my JD 990. I believe JD calls for the 8B for my model tractor. For those of you who have one or have used one: Does it have much digging power? Once the initial jobs you have lined up for it are completed....does yours just tend to sit without use...

Hello everyone, My 990 is about 4 years old. Even when it was new the bucket would drop both under load and without load. I tried to get it fixed under warranty but there was a misunderstanding about the loader being a 1 year warranty and the tractor being a 2 year warranty. Anyway, I finally...

Well it looks like I am trading my 850 MFWD in for a 990 MFWD w/300cx loader that has 40 hours on it. It looks brand new as it should and was 13k plus my 850. What do you folks think and what can I expect from it? Need it to run a woods 15 foot finish mower,6 foot woods RD7200 finish mower, an...

Would a JD 990 MFWD with R1 tires be enough tractor to pull a 6 row JD 7000 maxemerge planter?

I'm thinking of buying a John Deere 990 4WD tractor. Can anyone tell me how much cheaper then the retail or MSRP I should be able to get this from the dealer for? Thanks for any help!

My father in law (Sir, to my son) got his new 2WD 990 yesterday. Attached is a Woods 72" finish mower. Perfect machine combo for what he wants it for. I enjoyed mowing on it a little this morning. Quiet, turns tight, plenty of power. I was impressed.

There are some nice deals on TractorHouse.com, like this: 2007 JOHN DEERE 990 For Sale at TractorHouse.com for $19,299. When I go to the local dealer he wants minimum $21,000. How do I get a better deal?

I have a jd 1070 w/80 fel and 8A bh. I'm interested in a new jd 990, but I would like to use the fel and bh that I already have. Does anyone out there know if this is possible. Thanks

After months of reading, searching, pricing, browsing, talking, etc... I finally decided on a tractor and took the plunge. I lost track weeks ago the number of tractors I compared, test drove, and almost bought. In the end, I decided on a new JD 990, 4wd w/ loader and I couldn't be happier...

I am thinking about getting a John Deere 990 MFWD tractor. Would it be a good tractor for a 6ft bush hog? I will probably be getting a FEL also. I have heard that the 990 is a really good no-frills tractor. Since I will be mowing 9 acres of grass that can get up to 6 feet high, I really...

I am getting close to the 50 hr oil change. I was told to change out the break in oil at 50 hrs. I am considering putting in the AMSOIL synthetic 15-40 oil. Is this a good idea?

I bought my 990 back in august of 05. I went to crank it this past weekend and its completely dead, it hasn't been run since around mid november. Do I already need a new battery? Should I just jump it off and run it a while?

I was planning on mounting my tool box on the JD990 as shown in the attached pictures. Drilling holes and adding mounting hardware to the sheet metal cover behind the seat. Anyone see a problem with doing this?

Still looking at the JD990, but I cannot find a spec listing the exact height of the ROPS. At issue is whether this will fit through a normal 7' tall garage door since the ROPs does not fold. Thanks

This is the latest quote I received from another JD dealer. Is this a good price given that it includes the wheel weights and all? I also have a quote for a 300CX FEL w/HD 61" bucket for $3500 and an LX5 RC for $1450. (I have another dealer's quote for $300 less - but with no wheel weights...

I've been looking at nearly every brand of CUT I can find around here, and after much confusion, research, and debate (and spousal approvals), I have settled on a JD990. Pricing quoted from 3 dealers I've visited has been roughly: JD 990 - $!6,700 (MFWD) 300CX FEL - $3700 6' LX Rotary Cutter -...

I am going to purchase a tractor to maintain my property. I have 8 acres of mostly fields, rolling hills, a 1/2 acre pond, about 2 acres of woods. I want to keep about 5 acres of fields looking nice with a bush-hog, and mow the other 3 acres with my JD lawn mower or a finish mower for the...

I have a John Deere 990 with only 1.5 hours. I am taking it to my grandfather's house which is about 10 miles. Is it too early to put it in the highest gear and go? I guess it would be 9th gear. I have been reading about breaking in the engine but was wondering if it would hurt anything to...

My 990 will be arriving at my house in about 48 minutes. I have been waiting for over 10 years now for a tractor. I have been looking at used ones lately but a friend of mine told me about the 990. I have worked on my Grandfather's farm all my life but have never driven a tractor (hard to...

Fellas, thanks much for all of your contributions to this splendid forum. Through the shared experiences of many, I've been able to access tons of practical, real-world data covering the gamut of topics relating to CUTs that's really, in its totality, impossible to derive from anywhere else all...

In the market for a 40+ hp JD with loader. Have 15 acres with horses, need capacity for general work in additon to round bales (800-1200 lbs.) Based on previous discussions, looked hard at the 990 - however, just ran into a 4320 with loader, 200 hrs, for $21, 900. vs. a used 990, 50 hrs, for...

Member Join Date: Apr 2004 Posts: 31 JD 990 + NH 451 -------------------------------------------------------------------------------- Need help! Does anyone know how to hook up a NH 451 sicklebar mower to a JD 990 tractor?? I tried to do it today and found that the JD's three point...

Well she's got to go. Perfect condition < 10hrs. Email me @tcw67@yahoo.com if interested in details. Details in my signature.

Need help! Does anyone know how to hook up a NH 451 sicklebar mower to a JD 990 tractor?? I tried to do it today and found that the JD's three point hitch is too narrow at the top. I finally just used my top link to the frame of the NH, bypassing their set up, but also making it impossible...

Greetings to all!! I would like to know how a 990 compares in size to a new 4020 series?? Is it closer to a 4000 or 3000 size?? I would also like to know opinions on 990 vs 5103. John

We are putting in a fence around about 4 acres. we have a deere 990. I am looking at a leinbach l7300 ($425) or a rotomec from the dealer about ($800). Anything I should know before I get the cheaper one?

I've narrowed it down to these two tractors for my 17acres. The TC40A is about $1,000 more. I plan to bushhog, rototill, landscape and build/maintain a 700ft driveway. The specs seem better on the TC40 but something about the simpler JD appeals to me. Will the JD handle a moderate sized...

I have a 05 990 FWD and I need help deciding which rear blade to buy. Right now I have all frontier equipment and I like to keep the color's matching but I have seen some nice blades. I would appreciate some help on my decision, I am looking to spend up to about $700 maybe more just depends...

At 27 hours, the oil in my JD 990 is still spotless clean. I have never had a diesel keep oil this clean. Anybody else have this with their tractors? It's so clean, I'm actually wondering if anything is wrong.

After lots of research and reading here, I have decided to go with a JD990. My question is where to get it? I’m in SE AZ but I’m willing to drive a bit to get the best deal. Who has the best deal? Thanks!

I am a current owner of a Kubota B7500 and I am jumping ship to Deere. I need a larger more powerful tractor. A friend of mine has a 990 he loves. He let me take her out for a spin this morning. I really like this tractor alot. I know its old school technology in alot of ways but that appeals to...

Hi folks, other then more horse power, is there any difference between a JD 970 and a JD 990 tractor? Also, will the power beyond hydraulic kit (back hoe tap off) made for the 990 fit the 970 and 1070? thanks again,

I'm looking at the following two tractors: NH TC35A 4WD + 16LA Loader, Quoted at ~$22,000 JD 990 4WD + 300CX Loader, Quoted at ~$21,000 Seems to me that the TC35A has the better tranny (12x12 SSS vs 9X3 collar shift), and better hydraulics and lift capacities. The 990 has a stronger engine...

I'm at 25hrs and was noticing some carrosion at terminals. I was wondering which optima? Doug990

I ended up paying 22,500 for everything. I got the 990 4x4 w/ the 300cx FEL the mx5 rotary cutter frontier 5ft disc and a diamond plated cover. Does that sound about right? What have others paid? Thanks Brandon

Anyone out there useing one of these? Please tell me a little about the 990. likes or dislikes.

Looking for a 8B Backhoe for the new John Deere 990. Can be used but in good condition. If you got one your not using, turn it into cash. If your a dealer and you got one that is fixin to cost you interest ........... talk to me! Rob-Lee@earthlink.net

Have concluded the JD990 is the tractor for my needs and am close to getting off the wallet. I would appreciate any comments or feedback from current or existing owners. Good or bad. Repairs etc. Thanks

What socket sizes are needed for the JD990 tractor? Is everything on the tractor and implements metric? Thanks, Steve

DEALER SAYS I CANT REALLY HAVE TNT,BUT HE SEEMS A LITTLE CONFUSED ABOUT MY OPTIONS. WHATS PLAUSABLE TO DO HERE, 3RD SVC, POWER BEYOND, ELECTRIC DIVERTERS, IM NEW TO TRACTORS AND ANY ADVICE IS APPRECIATED.

I am currently looking at these two machines and I am having trouble making up my mind.The L4400 is a new and unproven model yet has more power and a shuttle shift over the proven 990.Could some 990 owners give me some information regarding their machines.I like John Deere.

I'm thinking of buying a utility tractor for my 20 acre hobby farm.Smaller than either of these models would do 75% of my work.(Occasional FEL work,snow removal and mowing the fields).However I would also like to work about 10 acres(plow/harrow).Could someone advise me(1)Are these tractors heavy...

I am just curious that there is little to no talk about the JD 990. Is this because it is too small for the farmers, and too big for the compact tractor shoppers? Kind of in no mans land. Just wondering...tried one out this week, and liked it, just as I did the 790. One thing that I liked...

What is the recommended ballast for a 300CX loader, JD 990, 4WD, with R4 tires ? When I e-mailed JD they gave me the following answer for R1 and R3 tires, but did not mention the R4 tires: 990, 970, 1070 2-WD R1 Tires Rear tires with liquid ballast, and 350 kg. (770 lb.) 3-point hitch...

What is the appropriate FEL model for the JD 990 4-Wheel drive? The JD Web “Attachments” page cites the 430 FEL, but I don’t see the 430 FEL on the JD “Build your own” page? Also, what is the difference between the LX5 and LX6 rotary cutters? How do they compare to an MX5 cutter (60 inch...

Anyone out there own or buy 990 lately am looking at 990 4wd MX6/430 loader quoted $ 20,300.00 is this decent

I have a jd990 with a jdmx5 cutter. I want to buy a trailer to transport it. I have a 2003 Ford Ranger 4-wheel drive with the FX4 off-road package. The 990 2-wheel weighs 3000 lbs. and the mx5 weighs 800 lbs. Will the trailer push me over my 5200 lb. limit? Anyone help?

I recently got the urge for a tractor for my 41-acres. It has been cut-over (3 years ago). I had been depending on a friend to help me with my food plots but you know how that goes. I called my brother-in-law (who is sales manager for a JD dealer and told him I needed a used tractor. He said he...

I have a JD 990 2-Wheel drive (40.4hp) for which I want to purchase a 430 loader and an 8b backhoe. What is the going prices for these new? I haven't been to any dealers yet.

I have a JD990. On page 9 of my owner's manual there is a section on adjusting the seat suspension. It says turn adjusting screw (A) clockwise to provide stiffer seat suspension, etc. I cannot find a screw in that position. Can anyone enlighten me on this? Thanks.

I have recently bought a 2001 JD990 with a JD MX5 cutter. It only had 69 hours on it and was like new. I paid $8500.00 for it. Am tickled to death with it. Have since bought a 6 1/2 ft. disc and a 5 ft. harrow for it. I'm now ready to do some serious deer plotting. I'm a proud papa!

I need three JD Quik-Tatch 42-lb weights for my JD990. If anyone in North Mississippi near Memphis has some used ones please call me at 662 429-6691. Thanks.

Can anyone suggest some ballpark figures on the following setup? I'm located in central Indiana. JD990, Ag tires, & FEL w/bolt in tooth bar. My local dealer priced this setup to me for $19,500.00. Thanks, Dave

Please let me preface this by stating that I don't want this to turn into an HST/GST debate. I recently bought a very nice used Kubota B2710, and while I really like the HST for a lot of things, it's just not quite enough tractor for me. The local dealer tells me he wouldn't use it to pull a...

Hello All I got my first rude initiation into winter snowplowing this last week. We received a good dump of snow, over 2 feet, in a few days. Then the winds kicked up to about 50, which blew the stuff into really nice hard drifts up to 4 and 6 feet deep. I had two problems. One, the temp...

I'd like to use my first post to announce the arrival of my first ever tractor purchase -- a brand new JD 990. For about 8 months I've been one of the "anonymous" visitors here. Thanks to Tractorbynet and all the users for the wealth of info and experience out there. The set up is 990 4x4...

I have the parts , tech , and owners manuals , picked up the block heater kit some time ago and figured it was time to put it in . Drained the fluid , got the kit out , heater , gasket, two bolts , and spacer.....looked at both tech and parts books , then the engine , book says need spcer , no...

I bought the kit to install myself , have the operators , parts and tech manuals . I figured it would be a cake walk , ,,,well after draining the fluid , I cann't find the frezee plug that is pictured in the parts manual or at least not where they say it is ,,, It takes two bolts to mount the...

This morning I just sealed the deal to purchase from a nearby neighbor a 990 w/ 41 hours on it, with the 430 FEL. The seller is throwing in a 513 cutter, 12" PHD, and ballast box. It's a great deal, and even though I've never owned a Deere (I'm awfully partial to Kubota Orange), the deal was too...

In looking around at the JD4310 and the JD4210, my eye was caught by a 990. These look like really nice machines! However, I see that they only come in a collar shift arangement. My question is as follows... If I am brush hogging and want to keep the PTO RPM's up, is there any way to vary...

<font color="#666666"> </font> Hi guys! We're trying to decide between a JD990 and a Kubota L4300 and don't really know much about either. Both are 2WD (don't need a 4)..the 990 has 40hp and the 4300 has 45hp. Both are comparably priced (JD 1k more). We are hearing good and bad about both...

I'm looking at a John Deere 990 4WD with 430 loader and industrial tires. The price my dealer gave me is $18,300 (after a JD rebate, he said). From what I've seen, this appears to be in the ballpark, but I haven't seen any recent price checks on this model. I like to buy locally, so I'm...

So far so good , got about 60+ hour on the clock . Dealer did the 50 hour and I forgot to have them look at the battery box , will I called it in the other day battery venting / leaking is eating at the battery holder . Dealer is coming to look at and fix next monday , over fill of battery ...

I have a buddy who fell in love with a 990 on a local dealer's lot. Trouble is that one was sold and the dealer is looking around for him another one. Before he signs on the dotted line, can any of you relate your experiences with this tractor, both good and bad. There's not a lot in the...

the dealer has picked up my 990 just the other day , along with doing the 50 hour maintance , they will be adding wheel wieghts , and I asked to have a valve added for out the back for future use... Dealer can and got the tractor , before I could get there to be around for them ,. I called them...

I have just over 40+ hours on the wee lil' beasty and they have been some of the happiest times of my life ..This weeks little victory was to reclaim a bit more of the field /garden from being over grown by weeds and brush . I had the good fortune to get a used cultervator/ scarfier (?)from my...

I am looking at several types of small tractors to work on the land we have purchased. I have currently narrowed it down to the JD 990 or the JD 5105. Any thoughts as to which would be the best buy? I really don't have all that much farming to do. Mostly mowing and the F/L work. I'm just...

I am wondering if anyone has any experience with the optional hood guard for use in protecting the hood with jd loaders. I just got a new 990 with fel (traded a 950 w/fel) and cant say that I am thrilled with the bucket that came on the loader. The bucket back is so low that as the loader...

Does anybody have any knowledge about the JD 990?