john deere 4310

Jd4310 having trouble cranking. Has anyone had trouble with fuel shut off valve stuck in off position. With the fuel solenoid removed . Putting my finger in solenoid hole the valve has no movement.

I can't tell you just how much I hate JD engineers. I busted the power steering line at the cylinder on my tractor. There is a flexible hose that goes from the cylinder to the hard hydraulic line that is about 18 inches long. Removing it from the cylinder is easy. Removing it from the hard...

First question. What is the default connection to the front axle if there is no power to the solenoid? Locked or unlocked?

I am looking for the codes for a JD 4310 - ePower Reverser. Sometimes it will not crank and is flashing 1 short, 1 long, and 6 shorts. Thanks in advance for any help. Danny

member Hi folks, Looking for some help with my John Deere 4310 e hydro. My machine runs fine, after about 35 minutes of use the pto shuts off. It’s like an electrical issue after warm up. I can hear and see the main pto turn on and off with the button but the mid pto doesn’t. I can let it cool...

Hi folks, Looking for some help with my John Deere 4310 e hydro. My machine runs fine, after about 35 minutes of use the pto shuts off. It’s like an electrical issue after warm up. I can hear and see the main pto turn on and off with the button but the mid pto doesn’t. I can let it cool for a...

Hello, in the process of replacing the hydraulic tubing that runs along side the left side of the engine from the steering wheel to in front of the motor. Have the hoses of each end of the tubing, all brackets off, suction hose off hyd pumps, front grill and radiator removed, and still can't...

Hi All, My power steering is almost out. I got a used 4310 about 3 years ago with about 1400 hours on it. I don't know the entire history, but could see the steering cylinder was replaced in case that is a clue. I have about 150 hours on it. Starting about a year/50 hours ago the steering...

I am stumped.... I have a 4310 ehydro with about 800 hrs on it. I was using it this past weekend and started smelling the hydraulic oil, I could not touch any of the steel lines. the hydraulics, transmission and PTO all functioned perfect. I changed the hydraulic oil and removed/cleaned the...

2004 JD 4310 hydraulic fluid foams while using hot or cold weather. when you push on pedal to move forward, it hesitates. Also the front loader is jerky and any rpm. i was trying to plow the snow off the drive and would start to move then seem like it ran out of power to move , so i stoped and...

HI, My hydraulics for the box scraper aren't functioning properly .I had the box scraper off the tractor for about a year for backhoe work . now I'm struggling to try to figure out why? The hoses are color coated ..reversed them and still no go . I'm wondering if I have gotten air in the...

I had the tractor in for repair and they said it needed a new battery. The dealer installed the battery and dropped off the tractor and I tried to start it 4 days later, it wouldn't start. I removed the new battery, charged it, then reinstall the battery and the tractor started. I ran it...

My father owned a John Deere 4310 Tractor and a 59 inch Snowblower. Years ago he went through the steps to start the tractor and then engage the snowblower and was pretty emphatic about the specific steps for engaging the snowblower. Unfortunately, cancer stole him, and I don't remember the...

I have a John Deere 4310 tractor, it keeps shutting off in the middle of cutting grass. Fuse 5 keeps blowing. Have replaced water pump and thermostat without any changes in the way it runs. Any ideas what could be causing this?

While doing a hydraulic oil service at 1600 hours, I found the pictured debris right down at the sump screen. The metal is like a sheet metal, unlike anytime I've ever had a bearing go bad. The odd thing is, the rest of the fluid was like new. There wasn't even a speck of debris when I...

Hi, I have a 4310 with Titan Trac Loader industrial tires 15x19,5and would like to get the Trygg studded tire chains. The rep said I need 3 inch clearance between the tire and fender. I measured both sides and the right side might give me 1/2inch to 1 inch clearance ( that's measured from the...

I HAVE A 2003 DEERE 4310. I NEED HELP DIAGNOSING A STARTING PROBLE. I TURN THE IGNITION, DASH LIGHTS COME ON, THEM TURN TO START AND GOES BLANK. I BOUGHT A NEW BATTERY, CHECKED THE FUSES AND REPLACED ONE 20 AMP FUSE. BUT DOES THE SAME THING. TRACTOR IS IN NEUTRAL AND PTO IS OFF. THERE WAS A NEST...

I took apart the front cowl and lubed/greased all springs and pivot points for the rear brakes that are sticking. I lubed/greased the joints and rods under the foot panel as well. The rear brakes still sticking until 15-20 mins into use then they free up. It's bad enough that if I'm going down...

Greetings, y'all, This spring brought me a new surprise to my 4310. I put it to bed late last fall with a full tank of diesel spiked with the appropriate amount of anti-gel (just in case I needed to use it to move an odd mid-winter snow). This spring I found a giant puddle of diesel...

Hello I am working on trading the R4 tires and wheels from my Deere 4310 for some R1 tires and wheels. I have an offer to swap with a guy that has R1s on his Deere 790. I am having him measure his bolt pattern and pilot hole, but I was wondering if anyone knows if these rims should swap...

Going to look at one in two days, wants 15200 for this and a lot of attachments. Anything I should look for when inspecting tractor?

On the 4310, should the glass fuel filter housing be full? I have a no start, and there is fuel in the bowl, but the filter itself is not saturated, the level is just below the filter itself. I think I have a problem between the tank and the filter. So just curious how much fuel should be visible.

Bought this today, going to fix it up over the summer at my cousin's house. Was sitting for a long time, jumped it and it cranks but would not start. Any common problem with these? Once I get it started I guess I will know more. Have only had a Kubota BX, but never a Deere of this size. Anyone...

I currently have a deere 455 riding mower of the 60 inch deck and it痴 time to get something bigger. Last year I bought a 72 inch finish mower to pull behind my Kubota compact tractor and I really wasn稚 very happy with it. That was far too big with the loader up front and the mower out back...

Hello All New member, so I'm going to give a little introduction. I live on a 10.5 acre homestead in the Northern Rockies. I've been looking for a tractor for snow removal (average 60" of snowfall), hauling logs (burn 4-5 cords per winter, but usually have at least two winters worth), food...

Hello, I feel kind of dumb . . . maybe I'm getting too old and just don't remember. I need to install the hydraulic lift cylinder AM124024 for my 59" JD snow blower . . . on the front of my JD 4310. I can't remember which end goes to the 4310 side, and which end attached to the 59" snow...

Need your help!!! My 4310 has alot of hours. Getting close to 5000 hrs. Never had this problem. Of course happens when a hay customer drives 120 miles to get to my place. Tractor was running fine. Moved 20 round bales out of the barn to load. Shut off tractor to talk to driver about how he...

I have Hydro JD 4310 with a 430 loader and I am having issues with the hydraulics. I took the loader off because I was using the mid mount mower. The hydraulics to raise and lower the mower deck worked fine and still do, as does the 3-point hydraulics. When I went to hook the loader back up, the...

I have a John Deere 4310 with the PowrReverser (so not the Hydrostat) PIN LV4310P135855. I took it out the other day and washed it and now it will not move (so at least it is currently a nice clean lawn ordainment). It starts and bucket works and rear three point works just fine. I checked...

I searched the various threads on the 4310 and most of them were really old, so I figured I'd start this one so it will be easy to see by others. I have a 4310 ehydro, it's a 2004 I think I purchased it in 2006 with low hours. In general, it has been a good tractor, I only have about...

Hi Guys, my husband was wondering if anyone knows if you are able to remove the knob, that controls the lever for shifting the front bucket up & down? If you are able to, how do you remove it? We tried to remove it but could not remove the knob. Thanks, Bonnie

My jd always starts on the first crank, up until 4 days ago anyway.:mad: I went to crank it over and it would crank but not start-up, same thing happened 2 more times. The third time it made a horrible screeching noise. There were no codes blinking. After mfing it a few times I raised the hood...

Aloha Folks! I am performing a valve clearance adjustment on a 2004 John Deere 4310 w/ eHydro and the Yanmar 3TNE84-EJT43 engine. The shop manual says "Locate the inspection hole in right side of the transmission tunnel. The flywheel can be seen inside the inspection hole. Align the number one...

Hello Everyone, First of all after much research & repair my husband finally got the John deere 4310 tractor running :-D If anyone can help me out that would be great. Now on to the valves part of the tractor. On the tractor there is a VALVE-3 SPOOL SCV part #LVA10901. On the tractor we...

Is there anything preventing me from switching from the wider rims and tires to the Ag R1 sizes? 7.00-14 (4WD) 11.2-24 source: TractorData.com John Deere 431 tractor dimensions information When I bought this as a noob, I didn't realize how much traction was going to be a factor living in the...

First, thanks to the folks on this site I have solved a lot of otherwise expensive problems with your advice. Not sure why the site says I have 0 posts, oh well. Recently I was responsible for repairing a deceased family members JD 4310 for sale by the estate. The PTO light would come on but...

I have a 4310 that is having some issues. I hit a stick tonight and ripped the leads out of the connector on the reverse solenoid. Shoved them back in and it worked. For about 5 minutes. Lost reverse but still had forward if i reset the key getting code 10, short-long-long-long. 天alve output...

Hi all our 4310 has been going good until now,the pto does not come on or runs for a bit then stops.Now when searching I see alot of pto light on and not working but mine is the light is not coming on or if it does the pto runs,so if the light is on pto works when it stops working the light also...

Hi all, Going to look at a John Deere 4310 tomorrow, and I am wondering about general opinions on this model and pricing. It has a hydrostatic transmission, R4s, 4x4, and is pretty decked out with convenience features, rear remotes, cruise control, deluxe seat, etc. It comes with a 430 loader...

Hi all, Going to look at a John Deere 4310 tomorrow, and I am wondering about general opinions on this model and pricing. It has a hydrostatic transmission, R4s, 4x4, and is pretty decked out with convenience features, rear remotes, cruise control, deluxe seat, etc. It comes with a 430 loader...

Wires got pulled out of weather pack connector. Found new female pins at case dealer. Blue bobcat wires worked. Got pto hooked back up. Working good. Anybody know what wire coming out of mfwd selenoid is the hot wire? Thanks

Hey guys, I bought a nice 4310 w/ 430 FEL yesterday. Can someone tell me what the fender switches do?

I have a JD 4310 e-hydro tractor. It is low on hydraulic fluid. I went to TSC to try to locate some and did not have any luck. I found some oil at TSC that said it was the same as J20C, but nothing that was for J20D. According to the manual it can take J20C or J20D, but from my research they...

Finished up the 3rd function selector valve install on my 4310 today. Ordered the 60" RK5 grapple set up for JD from MTL on Saturday evening. Got a call from them today telling me they have 4 more to deliver in my area and should be here on Thursday. I already had a pair of 3/8" hoses from a...

Thank You all for your input so far. It's been much appreciated, Sorry it's been so long since my last post. BUT... my husbands hip popped out the socket, Then he had revision surgery on July 25th. He is feeling much better now. First Off, I cannot believe how much we have learned so far. We...

I hear a click from the fuel shutoff solenoid when I first turn key but I see in the schematic there are two coils in the solenoid with one energized from start relay (K2) and the other energized from shutoff solenoid relay (K3 which I checked). K3 is controlled by fuel solenoid timer module...

I have a JD 4310 ePowerReverse. Just went to go use the tractor and was driving around with no problem. I went to put the tractor in reverse and it moved backwards about 2ft and would not move any more. The indicator lamp had 1 long flash then 2 short flashes pause 2 short flashes then a long...

Hi Everyone, I was wondering if anybody knows anything regarding the diagnostic code light? On my tractor, my husband wanted to try & see if any fault codes were blinking. It happens that we are not getting the thing to light up. We took out the button out, & took out the part that houses...

HI Everyone, my husband & I bought a 2004 John Deere 4310 Model tractor. VIN#- LV4310P336460 I was wondering if anyone else owns the same model tractor??? I am wondering with the tractor are there different models? I am trying to pin point specifics on the tractor. I am trying to figure out in...

I have a JD 4310 Hydromatic and the 4wd is not engaging. The switch lights up. all fuses and relays have checked good. The hydraulic cylinder that engages the 4wd lever on passenger side is not working. It is always "IN" it does not extend. I need some help diagnosing this. The MFWD valve and...

I have a JD 4310 Hydromatic and the 4wd is not engaging. The switch lights up. all fuses and relays have checked good. The hydraulic cylinder that engages the 4wd lever on passenger side is not working. It is always "IN" it does not extend. I need some help diagnosing this. The MFWD valve and...

This 'fix' might not be for everyone, but since the parts to repair a sloppy loose steering wheel exceed $200 ($338 for whole tilt assembly) for a JD 4310 or most 4x10 and 4x00, I decided, why not try it. I used strips from a cut up spray paint can, and put 4 in at 12, 3, 6, and 9 o'clock...

Started my JD 4310 (2005) and noticed loader lifted very slowly and steering lacked power. Let it warm up and now loader won't lift and won't even go forward or back (pedals). 3pt still lifts although very slowly. Seems to have lots of transmission fluid according to glass. Now she's stuck in...

Yesterday I went to move my JD4310 ehydro and when I first went foward I was OK.. but no back up.. went to go forward again no forward... turn off the tractor turn on same thing happened...this morning same thing I noticed what looked to be 1 short, 3 long on LED... Of course our owners manual...

I have changed the fuel filter, changed the fuel in tank, replaced selenoid, prayed and wept a little. I have manually filled the line from fliter to injectors and it will run until that fuel runs through, but no fuel moving from filter housing into line. The filter housing is full of fuel by...

My tractor dash temperature gauge keeps climbing up to the red, and beyond (!) What I've tried so far: 1. Replaced the oil (no milkshake, no glitter), it was due but not way overdue. Replaced the radiator fluid, it was due. Probably overdue. From a cold morning start on new fluids, it gets...

so the rockshaft housing has a crack running down the center between the mounts for the top link. I think this piece is cast and probably would not be able to be welded. anyone have any experience with this. How much to have dealer remove and replace... or the dream that it can actually be fixed...

Name is Paul, Family and I recently moved from a gorgeous 3 acre lot in Sandy OR to a 2 acre lot in central OR, brought our beloved 4wd JD 4310 along with us, with all the snow were getting now the little JD is getting quite a work out, now just over 11 years old and 550 hours on its clock...

Just installed the 3rd valve kit and power beyond today and notice I had a little leak under the seat. it appears to be coming from the left side rockshaft control valve cover, in the area where the ABC selector is. According to the the parts diagram there are a couple o-rings in there. has...

Hi, I've started to look for a backhoe for my yard (and maybe for some side work in the future), it's only 1/2 acre but there are a number of projects it would be helpful for. I found what looks like (on the surface) a really good deal on a 31 hp Deere tractor with backhoe, please see...

My 2003 model 4410 has just under 1400 hours on it and has never given me a problem until recently. When mowing at full operating speed and after it has been running for 45 minutes or so, it will stop dead and the indicator lamp on the Ehydro will emit 3 long flashes. Sometimes the engine will...

Greetings! After changing the thermostat and coolant in my JD 4310, I started filling the coolant reservoir with 50/50 mix when I noticed the mix dripping out of the bottom of the tank. I have since found out that cracking of tank is a frequently encountered problem with this part. There...

Hi all, I've been using this forum for about 7 years and I've finally got a problem I can't solve via the forum, so I created an account and posted a question (about starters). Anyway, I have a John Deere 4310 which I bought new 13 or so years ago with a Bradco backhoe attachment and JD front...

I tried to start my tractor for the first time this year (it's been in the garage over the winter and the ground is finally not too soggy) and all I get is rapid clicking sounds. I tried to jump it using my car, and after 4 or 5 tries of nothing but clicking sounds, it started and I took it out...

Thanks for taking time to read this and offer suggestions. I recently purchased a 2005 JD 4310 (serial number: LV4310H331629) with only 100 hours on it. After casting a broad net, this was the machine I thought best to purchase. Problem is, it didn't come with the options/attachments I...

4310 brought new in 2005. At start-up, temp gage needle climbs steadily to full hot over 3 minute time span. Engine temperature is normal according to multi-meter temp readout & gut feeling. Needle goes to cold when sensor wire is unplugged. Needle goes full hot when sensor wire is grounded to...

The wife recently inherited a JD4310, 4x4, JD loader and JD backhoe attachment, we are probably going to sell it and just trying to figure out a price for it, it is in good cond, 728 hrs, hydrastat, good tires, the loader and backhoe are quick disc and we have the lift arms for the 3 pt hitch ...

Hello I have been looking for a JD 4319 Repair manual for my husband tractor. He has the hydraulic fluid and don't see where to put it .. Any info will be greatly appreciated..

I have a 4310 that the fuel shuts off after 15 seconds everytime you start the tractor. I had removed the solenoid and the tractor will run until I stick my finger in the hole where the solenoid goes and press in the plunger to shut off the fuel. I assumed I had a bad fuel solenoid so I...

I have a JD 4310 compact utility tractor. When mowing with the belly mower, the PTO disengages. I can usually get about 30-45 minutes out of it, then it seems to warm up and the PTO shuts off. If I wait for 10 minutes, I might get 5 more minutes of mowing. Then the PTO stops turning on...

I recently picked up a 2004 JD4310 w/power reverse (1200hrs) as a project tractor. The owner said it wouldn't start and it was weak in reverse. I fixed the starting issue, changed ALL fluids and filters, cleaned the screen intake filter, and lubricated all the clutch linkages. It works perfectly...

We are buying a 5 acre plot and the owner is also selling a tractor along with it. I have shopped around and been interested in a New JD 3032e Ls g3033 and a few others but this one is a bit cheaper. So my questions are should I get this tractor at this price or go with a new tractor that's a...

I have a 32hp John Deere with the EPowerreverser transmission. Some days it works just fine, other days it will not go forward or reverse. I checked the fuses, electrical connections and linkages, found nothing loose. Appreciate any help. Thanks Jim

Am getting a long followed by 3 shorts code > What does this mean? Tractor won't move forward or back. Lifts front and back work.

JD 4310 want come out of 4x4. I think my transmission pin is stuck or broken. Can anyone tell me how to check? The MFWD cylinder is working but the tractor will not come out of 4x4. I have disconnected the cylinder and there is no resistance on the transmission lever. I noticed that you can...

I have a safety switch that is preventing the tractor from starting, I have junpered the seat safety switch already and am now looking for the neutral switch I think it is under the deck but cant figure out how to test it. Some one else said it was in the transmission case hole. I am waiting...

Have not done any investigation yet just wondering if anyone has had this problem. Would have looked at it but my generator crapped out. Bad night. Anyway. Have flashers and rear work lights. Just no dash lights and headlights. Will investigate in the morning. Thanks

The lettering on my tractor switches for MFWD, load match, cruise, etc. Have faded or worn off completely and I'm just wondering if anyone has come up with any creative solutions to relabel them.

I thought my 4310 had ran out of fuel. It hadn't but I filled it up and it would crank, but was not getting any fuel. I found out my fuel shutoff solenoid wasn't working and bought a new one. It still doesn't work. I need to know which fuse or relay sends power to it. My fuses are good. I don't...

jd 4310 has code 1 short and 3 long. I cant find a problem with wiring. there was a problem with a 2 wire connector, under tractor that was pulled loose by brush. wire repaired but tractor wont move forward. backs up fine.

I'm trying to adjust the rockshaft to keep it from going into relief when I lift it up. So far I've adjusted the "lift arm position feedback rod" as short and as long as it will go and I can't tell much difference between either of them. As it is, when I pull up to position 4 (of 6) it is...

My 4310 has had an issue for a while now, but it appears to have gotten worse. I have a John Deere 4310, E-Power reverser with mid mount mower deck powered by the mid mount PTO. 1. When I engage the Mid Mount PTO, the F-5 fuse blows 2. The rear PTO worked fine, so I just stopped using the mid...

So I am in the process of replacing the LVU17467 seal #33 on the diagram and have the front hub and all the bearings and gears out of the front end. I confused on how to get the two housings apart. There is a nut that is treaded on that i believe needs to be removed to allow me to separate the...

Well after 11 years it looks like bi need to finally replace my original battery. Any suggestions on with what? Should I look at optima? Or stick with a standard battery from the dealer? Thanks for the help!

JD 4310 Hood hinge repair, and hood operation

Hello, I am a novice with tractors. I removed the hydraulic lines that control opening the bucket on the loader and connected the lines for the mower deck and it won't raise or lower. It sounds like it is trying to do something but nothing moves. :confused: When the lines for the bucket were...

Hello, I purchased a John Deere 4310 last year. First tractor I have ever owned. Learning as I go! It came with a 60 inch mower deck, loader, Post hole diggers, Tiller and a few other attachments. So far I have been real happy with it.

Hello - I'm new to this forum and I hope someone knows my tractor's problem and solution. My 4310 eHydro works great moving around the property working the loader and minor mowing and such, but once I start doing heavy mowing of the hilly pasture after about 30 to 40 minutes the tractor just...

My 4310 has a bad vibration, mostly around 1700+ rpm. I pinpointed the torsion damper and just wanted to see if anyone can help me verify that it is the problem. The springs in the damper are loose- around 1/4 in. empty space. If you shake the damper back and forth the springs rattle freely...

My dad passed away and has a JD 4310 with 430 loader and turf tires. He only put about 300 hours on the tractor in 9 years of ownership. It is in excellent condition. I plan to buy it from my brothers and sister. What would be a fair price to offer them for this tractor. Thanks!!

Any alternative to JD branded hydraulic filters? Don't want to pay a premium just for the logo... Thanks much, JW

Hi everyone I am trying to let everyone know about a scam that I got sucked into. It's running on Kijiji, and craigslist maybe even eBay. It's a 2004 John Deere 4310. Price 4700 I know it's an unreal price but I fell for it. The seller directs you to a website Cardwell & Carson Consignment where...

Hi everyone I am trying to let everyone know about a scam that I got sucked into. It's running on Kijiji, and craigslist maybe even eBay. It's a 2004 John Deere 4310. Price 4700 I know it's an unreal price but I fell for it. The seller directs you to a website Cardwell & Carson Consignment where...

i am working on a 4310 i have replaced the transmissin controller it is a e-hydro with cruise control, the controller is sending 2.38 volts out of wire F-3 for the flywheel spd. sensor so I cut the wire in case of a feedback and the controller is still sending the same voltage. I have all my...

Just wondering if anyone has put rear wheel spacers on a 4310 and if so what is your opinion. I'm considering getting a set of 3" spacers to put on the back of mine. I use the tractor mainly for mowing and snow removal and my place is predominately flat, but out by the road it's a different...

I got the 4310 a few months ago to replace the JD 850. In the 850 manual it said to idle the tractor with the High and Low range selector in neutral and the gear selector in 2nd gear. Presumably to circulate the fluid (but I really have no idea). Anyway I don't recall seeing any such advice in...

Noticed when I was sliding around in the snow today that the left front tire appeared to be the only one spinning. Just wondering if that was normal or not. I've lifted up the front with the FEL before in 4WD and saw both wheels spinning so I'm assuming that the front axle works like the back...

Hi guys. Im pretty new to the forums here and would like to start with a big thank you for all of yalls help. Some of us are lost without such helpful guidance. I recently ran my tractor JD4310 out of fuel. Its the first time ive done this in 1100 hrs(roughly, both fuel and hr meter...

Just curious on where you stow away your chains on your tractors? I had a JD 850 without a loader and I just wrapped the 20' or so chain around the front weight holder. Seemed to hold well and never had a problem with it there in the 7 or so years that i had the tractor. The new 4310 has a...

After using my 4310 for about 45 minutes or maybe longer the HST starts lurching like the transmission is slipping. i have changed the suction side filter and cleaned the screen. Any suggestions? Thanks Will

My 4310 E-HYDRO won't move and it shows three differents codes: *-** (short-long-short-short) *---(short-long-long-long) --**(long-long-short-short) any suggestion!!!

I have a 2002 john deere 4310 with 850 hours on it and it stalls under a load. Like going up hills in high gear, back dragging, and lifting material out of piles. Didn't know if there was any known concerns. Have replaced all filters and fluids with no change. Any help would be appreciated. Thanks

I have a 2002 john deere 4310 with 850 hours on it and it stalls under a load. Like going up hills in high gear, back dragging, and lifting material out of piles. Didn't know if there was any known concerns. Have replaced all filters and fluids with no change. Any help would be appreciated...

Our non-profit has a JD 4310 with about 800 hours on it. I noticed it has started losing power when bushhogging, I have to push in the clutch, stop, and then release the clutch and the power seems to come back. I noticed last week when climbing a small incline, the power slowed and then went...

Hello i have a john deere 4310 hydro

Does anybody know anything about the codes on the john deere 4310 hydro? My tractor is showing 1 short 2 longs 1 short code,does anybody know what that means? Thanks Scott

It is hit and miss. I started it today and the mid pto started without blowing the fuze, but I noticed the rear PTO was turning at the same time. I turned it off and on a few times then it started blowing the fuse again (three times). Does anyone have a recommendation? Thanks

Hi, I hope I can get some advise. My 4310 JD Tractor has been great but I accidently poured diesel in it that had water in it. I did not realize it at the time. Until it started running rough(it sometimes sputered once in a while before the bad fuel but now after the bad fuel it is much worse)...

Theres one at a local dealer for 14,500. Its eHydro, very nice condition, 130 hrs, canopy & R1s. 420 Loader. Does this sound like a good price?

I have a John Deere 4310 and it rolled back when I was getting it out to use it and then it wouldn't go forward or backward. I have had this happen in the past and replaced a fuse and was up and running. I looked and replace a couple fuses and checked the connection on the seat to make sure it...

Need a belly mower for a JD4115. Found one that is off JD4310. That one has this number on it and it is a JD # TC 4272X011560. Does anyone know where one is for sale used that fits? We are in Lansing, MI. Thanks

I was using my 4310 yesterday. When i took it out of the shed the hydraulics seem to have air in it while raising the loader. I drove it out of the shed and hooked to a car I was going to work on and everything worked fine. It went forward and reverse, I pulled the car out a way and noticed a...

Need value of 2003 John Deere 4310 compact utility tractor, 4wd, e-hydro with 430 loader

I have a JD 4310 with front mount snow blower. Last night I was working it very hard for a few hours and saw some fluid on the snow so I stopped and looked under the front near the lift ram. I saw some fluid dripping but could not tell from where as it was getting dark. I got it home in the...

Took the instrument panel off my JD 4310 to work on it. That part is all done and works great.....just struggling now to get the tilt wheel lever positioned correctly as the instrument panel sets back in place. Anybody been there/done that and have some helpful hints.....other than facial...

Hello. I'm new to the forum but I have been visiting this site for well over three years as I searched off and on for a tractor. The information on TBN has been a great aid in the decision making process, so my first act as a member will be to thank this community for all of the information...

I am a new tractor owner. I bought a used 4310 2070 hrs. It now has 2075, I also purchased a new 5' rotary cutter. As I mow the throttle will not stay set at 2600 rpm setting. I have to constantly use my hand to keep up the rpm, it wants to drop back to about 2000. I expect this is some...

I dropped a hay bale on the top of my hood broke out a 8" piece on the top any ideas on how to repair or where to look for replacement

Has anyone ever replaced the hood on a JD 4310. When I bought mine (used from a friend) the hood was badly cracked. While bush hogging the hood just fell apart. Ordered a new hood, fuel door and hood/tank pads and seals. Need to know where to put the new pads (part # LVU10461 & LVU10458). Does...

I have a John Deere 4310 that i am going to put on the market, it has a 430 loader, shuttle shift trans, just a real nice tractor with 1360 hours on it, 4 wheel dr, epowereverser, tractor looks and operates great, no known issues, I am thinking about asking 14,000 for it, is that a fair price...

I have a 4310 hydro and a couple days ago the tractor stopped going forward and back when I pushed the pedals. Then the front end loader wouldn't raise or lower. I did a hydraulic fluid change and now I have no hydraulics or power steering Any suggestions

Our 4310, which worked perfectly yesterday started this morning but won't keep running. Starts every time, but then only runs for about 30 seconds and dies....any ideas?? We are NOT mechanically inclined, so can't check much ourselves...

Hi, I just mounted a used Shaver HD 8 post driver on my tractor. It's on the three point hitch. I want to put a short pipe extension on it to connect the return pipe. Went to the hardware store today. No go. I think it may be metric. Hoping someone may know what size the hydraulic fill hole...

I need to find the wiring diagram for the ignition switch on a John Deere 4310. The hour meter died and I am installing an industrial meter. :confused2:

I have a Wallenstein backhoe GX 600 on a John Deere 4310 subframe! Can it be attached to a John Deere 4110? Any helpful advise would be appreciated. Thanks.

my 4310 has intermitant problems moving forward or back. have to stomp on pedals to go. Have replaced hydro filter,cleaned the suction screen and replaced all hydro oil. Seems to be in the electronic pedals ??? Thanks Tom

I have a JD 4310. When either drive peddle is push only the front axel has drive power. Any suggestions of where to look first?

trying to find a rear rim and axel for a JD 4310. The prices at the dealer are out of sight at least I think so . any where aftermarket websites I should check? The rim is a 19.5x 13

Hi, I have a 4310 that the the left side lifting link has broke a couple of times. I've welded it back together. Holds for a while. Well it's time for a new one. I looked up the part on the JD parts website. It is part # CE 18326. It says that the part is no longer available. Anyone have a...

Hello, Came on here to find the value of my 4WD JD4310. Sold the farm and cannot take this along and it pains me not to be able to keep it. I have all the books and manuals that came with it. Forget the numbers of the accessories but I ordered it from Deere in 2002 or 2003 with these...

I'm new to the site (although I've been browsing for a while) and have found some great information to narrow down the seemingly infinite brands, sizes, and configurations of tractors to what I think I need. I've got 20 acres (17 treed, 3 field) all of it pretty hilly (some 50 percent). I'd...

Which of these two would you rather have? They look to be almost the same tractor, built around the same time. From looking the 4410 has maybe 2 or 3 HP more and a weighs a few hundred more pounds. Lifting capacitites are about the same. The 4410 has a 430 loader the 4310 has a 420 loader...

Is there a sight where I can download or look at a repair manual for my tractor free? thanks Jim

I have a 4310 john deere. I bent the tye rod and need to remove it. I took off the nuts on each side that holds the fitting in the casting but can not remove the bolt with the grease fitting on top. Is this theaded into the houses along with the nut. thanks for the help, Jim

I have a slate roof that can not be walked on. And there are aluminum gutters at roof edge. week or so ago I noticed water coming out of a wall. days of troubleshooting later, I am convinced it is improper flashing around a waste vent. Edge of roof is about 10' high and vent is about 10' in. I...

Found a good size oily wet spot running down my right front wheel, enough to make a 5" dia stain on the floor. I've heard of axle seal leaks here, but not sure what I'm up against. Anyone able to direct me me where to start? Thanks, JB.

I just bought a used 4310 with 1200 hours, 4wd, FEL and power reverser trans. When I hooked up my shredder to it yesterday, the pto worked fine, the FEL loader works well, but the three point lift only raised the shredder a couple of inches off of the ground when the selector is in the highest...

I am thinking about buying a used 4310, it is 4wd with FEL and has about 1200 hours on it. I have owned JD 850 and 770 in the past and just sold my Kubota L2900. Some questions: 1. How will this tractor compare to my 770 and L2900 ? 2. What are the pros and cons of this rig ? Thx.

Hey guys, new guy here with a strange problem. Ive got a JD 4310 ePowerReverser tractor, about 430 hours, has always ran great. The other day, it quit while mowing, blew the F5 fuse. I ran the wiring harness, cant find an open, but discovered (by chance) that if the MFWD switch is off, and...

I had the top of my spool valve casting blow out. Is this a common problem. It is a 2004 with only 465 hrs on it. Anybody got any ideas about this one. 2 pictures attached. Thanks Jim

My 4310 temperature gauge pinned high; Replaced the thermostat, removed the water pump and tested (perfect) as well as the fan belt, radiator, air filter etc. When idlling the temperature gauge climbs to pinned when the sender is reading 507 ohms. The water temp measures 107F at the threaded...

Looking for a set of six bolt 7X14 Ag rims for 4300, 4400 JD. I'm located in central VA.

I have a 4310 that the rockshaft control lever is really stiff, and I don't think it is lifting the arms up all the way. I had a ballast box on all winter, and after putting on my Rankin post hole digger, it drags on the ground. It looks like it needs to go up about 4 more inches. The lever...

I went and plowed snow with my 4310 and worked the tractor for about an hour, we had some friends drop by so I stop to visit, probably another hour. When I went back to my plowing the tractor would not move forward or back. I let it run for about 4-5 minutes, and everything started to work as...

I recently bought a nice 2005 JD 4310 with 4 in 1 bucket to power a Bearcat chipper. This is the only implement I use with the PTO. Just found out if I get off the seat, the PTO shuts off. Obviously I have to be in the seat or put a large weight on the seat to be able to run my chipper. Has...

Hi all, my first posting here. I am a single mom and have 6 acres, but there are only about 2-3 potentially usable acres on the top of the ridge where the house sits with a small slope in front and big slope in back. I want to add a little "curb appeal," other than what I have now. The lawn...

I have a 2002 JD 4310 with power beyond. I have a chance to get a factory top n tilt from a 2004 JD 4310 with the electronic control for the joy stick. The rear bracket on the 04 appears to have all the necessary brackets for the power beyond to keep it on my tractor. I will have to take the...

Well, I was going to wait and do a full story on my cab so there wouldn't be too many un-answered questions. That way it wouldn't string it out. However, I'll throw it out here and do the best I can. I sometimes don't check in for several days at a time so I may be slow to respond to...

I bought a 4310 with 430 loader. It was supposed to have manuals but did not. I need to buy a metric threading die for something else. I want to know if I should get a single die or a kit. Does the 4310 and 430 use metric threaded bolts and Zerks?

We have a five year old JD 4310 that's had some problems along the way. The transmission was recalled the first year we had it and was replaced. Today, while clearing brush, it stopped moving. In any of the ranges (ABC), it won't respond to either forward or reverse pedals being depressed...

Have any of you guys ever experienced the following... Approx. 1-1/2yrs ago developed a problem with my 2005 JD4310. After spraying down the tractor, I literally could not get it to move. I found that if I depressed clutch, left transmission in neutral, and moved the reverser lever from neutral...

I am a brand new owner of a used JD4310 4W HSD front loader. I bought it thru a dealer for $17,000 with loaded tires, a bearcat 540 PTO Chipper/Shredder and ballast box. Machine has only 90 hours on it. I have 10 acres of woods and stone walls to play with and want to put a backhoe attachment...

Bad case of cranial-rectal inversion, backed my grader box into a frozen rock-hard pile of #72 gravel, broke the top 2 cast-iron "holes" for the top link pin. I had the top link pinned in the middle spot or it would have busted all 3 of them out. Split real nice. Don't have pics. Ordered the...

Hi I have been having awful problems with my JD 4310 3-point hitch. It will only stay up if locked in this postion. Otherwise if you lift it and let it go it comes all the way back down. So far I have changed the rate of drop valve, rockshaft piston ring and back seal. More recently my...

Does anyone know where the wires to the temperature sensor are located on the JD 4310. Just got on my machine today and the guage is stuck on the low end pin, does not move even slightly. I'm thinking the wire is disconnected or broken - as my Gator problem of last weekend was due to critters...

Hi, I'm new here and I'm looking to buy a JD 4310. I found one and I'm wondering if this is a good price. It is a 2004 JD 4310 with 150 hours on it. It has the ePowrReverser 12/12 transmission, MFWD, agriculture tires, and the folding rops. It looks good, nothing is missing or broken. I...

Looking for advice on how large a rotary cutter I should buy, 5ft or 6ft medium duty. I have a JD4310 32hp. I have approximately 8 acres of flat horse pasture that is in good shape. I plan to mow the pastures 4-5 times annually. I made my first cut in late april with a BORROWED 4 foot...

Does anyone have a hydraulic top link on their JD 4310? If so, where did you get it and what did it cost?

I broke the hydraulic steering cylinder one hour in to my "work weekend. JD dealer says the cylinder is $450.00 to replace. Can I use a generic cylinder? How long should it take to replace the cylinder and straighten the tie-rod assembly? Help!!!!!! Stumps suck!!!!

I ordered an MX-5 mower back in June from my JD dealer. It was originally promised by 8/1,then 8/20 ,now he say after Deer season. My questions are, Does anyone cut with a 4310 using an MX-6 mower,and how well does it work? Is the MX-6 mower too big for the tractor?I bought the Mx-5 based on the...

I'm going to attempt knocking down a one story wood frame house on blocks. I then plan on burning the debris pile. Any suggetions on tools or equiopment I should use to make the job go smooth? Any other suggestions would help.

I need to replace the battery in my John Deere 4310 and have read on TBN that "Optima" is a great replacement. Does anyone know the Optima replacement number and a recommended source?

Hi Folks Been a long winter and I did use the tractor to clear snow from the road but today was warm so I thought I would get some seat time. I took the front grill off to check the battery and noticed some battery acid leaking from the stock battery. I would like to replace this stock battery...

Just pick-up this 2004 JD4310 from McGrew Auctions in Seven Valleys PA. Overall the machine is very nice. Paid $10,275 for the tractor with eHydro. I'm going to drop it off tomorrow at my dealer to add a new loader.

I just got off the phone with my dealer and he gave me a price of $1050 to add a mid-pto w/3rd SCV for a mid-mount mower. The parts were ~650 bucks with the rest being labor. He says it will take ~7 hours to install. Is this something I could do to save the money? I'm somewhat mechanically...

Hello, I've never been around tractors much and not much experience with much more than a riding mower. Just bought 37 acres and needing a compact 4wd and loader, backhoe would be great, but not totally necessary. I am looking at an '03 JD 4310 ehydro, 4wd, 430 loader and 48 backhoe. Less than...

I have found A John Deere 4310 its a 2003 model with a 430 fel, it only has 30 hours on it. I can buy it for $14000 from an individual, it looks brand new and has all the options and runs great. This is a great buy is it not?

My 2 year old 4310 has had the front left wheel seal replaced at about 250 hours (covered by JD)and now my right front wheel seal is leaking. Only has 297 hours on it. Its never been overly worked hard. Of course the warranty has expired. Has anyone else out there had the same problem? Thanks Paul

2003, JD 4310 Compact Tractor Somebody talk to me about the rear remote hydraulics. I purchased this tractor with remote hydraulics for the purpose of driving a log splitter and using a hydraulic center link I have on hand. The dealer sold it to me knowing what it was for, but when the remote...

I have a new 4310 that did not come with a factory 3rd SCV installed. Does anyone know if this kit is still availabe for field installation? In addition, I would like to install the power beyond kit. What is the difficulty of installing these two kits? Any info is greatly appreciated.

I've been in Iraq for nearly a year now. Today I saw my first John Deere! You would be surprised how exciting this is to someone who owns one (790) and is not able to use it currently.... Anyways, it was a 4310 w/300X loader and a "Armstrong Ag" box blade. They were using it to clear some...

I have a 2002 JD 4310 E-power -reverser transmission with 120 hours. Just bought it used from original owner two weeks ago. Worked fine for two weeeks. Then I pulled some stumps this past Sunday. Worked her a little hard for an hour or so. Shut her down fine that evening. Next day, clutch...

Am I missing something? The L3400hst seems more powerful and is $3000 less in My area. I have 20 acres, 15 are fields, and need mostly for bushhog and 2 or 3 acres of tiller work. This is the new L3400 with Hst transmission. Tried both, not that much difference as I can tell, as I am new to...

I hope this belongs in Owning and Operating and not Buying and Pricing. Currently I have a little over 28 hours of seat time on my new 4310 and would like to share some of my experience. Overall, I am very impressed with this tractor. The fuel consumption has been impressive. With 24 hours...

I am about to buy a FEL for a JD 4310. The salesman touts the 300 CX as the new, improved replacement to the 430. The 300 CX has a curved arm for better visibility and a better attachment clamp to the front of the tractor. However, the 300 CX main mounting post is formed of cast iron. I...

Thank you to all who responded to my question regarding my new 4310 and the engine lugging problem. I had a chance to take it to the dealer, and he indicated a "brake adjustment" had to be made. With internal wet disks I am not sure exactly what he meant, but my lugging problem is nearly...

I am a new member to the forum and a new owner of a John Deere 4310 e-hydro. It replaces an X-595 which I owned for about two years. I live in a mountainous area and have found my 4310 to be a good performer, but slightly short on power on the long steep climbs here (engine lugs). I have...

After reading about everything I could find on this great site about the big 3 in the 30 hp HST class, I believe I am going green to keep my 17 acres in shape. My main reason is the difference in dealers. The fact that they sponsor a golf tournament and my wifes family is from the Quad Cities...

I have a John Deere 4310 diesel 4wd with 230 hours that I recently bought. After about 45 minutes running, the tractor stalls. It has no problem restarting but when I press the gas, it stalls again. I replaced the fuel filter and air filters and tried it again several days later and same...

Sold my old Deere and am negotiating for a 4310, loader, 200 hrs, 4x4, power reverser, great shape. What is a fair price? Thanks for any info.

Hi - I'm considering purchasing one of these two tractors soon. I'm looking for a 30+hp tractor for brushhogging about 8 acres and grading/snowremoval a 1000+ foot driveway. I could also see doing wood chipping now and then. Also, I want to make sure its easy for my older children to...

JD4310 ehydro w/430FEL and HD bucket Kubota L3130 HST w/LA723 and HD bucket i can buy both for about the same price. seems i am getting a better discount on the JD, maybe due to new model coming out. financing rates are same as well. both dealers seem to have good service, products, etc which...

hello all i just wanted to find out if the JD 4310 and DX33 are basically the same tractor spec wise?? if they both cost the same which one would be better deal?? seems JD is heavier (2900 vs 2474), less clearance (10.5 vs 14) and slightly larger with slightly less hp and what is the...

hello all well it's come down to the wire. after a few months of going back and forth (need vs want, new vs used) and what size (class2, class3 etc) i have come down to these 3 tractors, at least i think i have.... I live in Montana and have 16 acres of pasture (some flat, some contoured), no...

So I went and priced these two, and was very suprised: JD 4310 w/430 FEL and 47 BH and Top n Tilt = $25,770 L3130 w/723 FEL and Woods 9000 BH and Top n Tilt = $32,200 I realize that specs on the FEL and BH lean in the favor of the L3130, but is there really almost $7,000 difference???

Hello everyone, I am new to this, I've been in the Air Force for 20 years and will retire soon. I want to start a small tractor-landscaping business and think that the 4310 with a 430 FEL and 60" box would be good. Am I right? and What is a good price for a new John Deeere 4310? Before AZ...

What is the widest rollover box that a JD4310 can pull? I need something heavy that will break up hard clay, but I would like to pull this at least 6" deep. I can get a used 60", but would like the 72", even though I don't know if I can handle it cutting that deep.

Lets win this one for GatorBoy!!

Got your attention didn't I? Well it is on ebay, at least for now. I reported it because obviously it is a fake. Ebay 4310

Got it narrowed down the these three. New B7800/LA402 FEL/R-4 tires @15,780--JD4310 ehydro '03 w/60hrs and 420 FEL @$16,500--NH TC33D '03 w/20 demo hours & 7308 FEL @ 17,700. Drove the B7800 today and was pleased. Heard the Kubota has a better engine and transmission than the Deere (not from...

Hello all and thanks for your time. Ive been doing some research on tractors and Im ready to take the plunge. I have gotten a couple of quotes and was wondering if you guys had any suggestions or comments. 1st quote was 4310 with 420 loader, ehydro and r4's for 21000. 2nd quote was 4310...

My 4310 is relatively new (25 hours). I have a question regarding the fuel cap. After I fill the tank up, and try and replace the cap, I only get two or three turns on the fuel cap and it let's loose and pops up. Do the fuel caps tighten all the way down and fit snuggly, or do they ratchet...

I just came accross a privately selling JD 4300 with under 1000 hours and a 420 loader for a very (VERY VERY) good price. I am planning to go look at the unit this weekend. Now for my delima. I have the literature for the 4310 but know very little about what changed between the 4310 and the...

I'm both a Newbie to this Forum and CUTs in general, and I'm looking at buying a JD 4310 for my projects. But within a few years though I’ll be moving from the flatlands of the Midwest to the high regions of Montana; that’ll be between 4500 – 6000 ft above sea level. I’d assume some minor...

I'm loosing too much sleep. I'm trying to make my first big tractor decission. Looking at jd 4310 and nh tc35da. Any help would be appreciated. Here are my specs. 4310 w/430 fel ehydro rear remote 61" hvydty bucket tc35da w/16la fel 12/12 syncro shuttle rear remote

I have a JD 4310 with the eHydro transmission. I bought the tractor new from K.C. Canary this past fall and it still only has 38 hours on it. Problem #1 After about 15 hours I noticed hydraulic fluid on the garage floor under where the tractor was parked. After close inspection I could see...

Quick tach bracket w/ JD 59\" snowblower on JD 4310 Last night I got around to attaching the Quick tach bracket for my JD 59" front mount snowblower on my JD 4310. I had originally used the snowblower on my JD 790. Anyway, the bracket came with 6 shoulder bolts and is supposed to be mounted in...

Hi folks... Will you help me decide between these 2 tractors... ? There's gotta be more than I read about in the literature... or the limited test drives I did... Pro's... con's... +++'s... ---'s... experiences... opinions... Like... performance... quality... ergonomics... quirks...

Hi folks... Will you help me decide between these 2 tractors... ? There's gotta be more than I read about in the literature... or the limited test drives I did... Pro's... con's... +++'s... ---'s... experiences... opinions... Like... performance... quality... ergonomics... quirks...

Hi folks... Will you help me decide between these 2 tractors... ? There's gotta be more than I read about in the literature... or the limited test drives I did... Pro's... con's... +++'s... ---'s... experiences... opinions... Like... performance... quality... ergonomics... quirks...