clutch

Lost my overrunning/slip clutch tonight on my old 14T, can’t figure out how to get this collar off so I can remove the clutch and open it up to figure out what broke. I can hear something metal clanking around inside. Is this collar pressed on? I removed the set screw but it won’t budge.

My question is, "Can I / Should I adjust the clutch pedal linkage range if the range between the PTO and Transmission engagement/disengagement is too large?" My Problem: So here is what I mean about my question. In a previous post I was having an issue with the PTO clutch not disengaging. What...

I have a Kubota L3940 HST and I have to adjust the clutch. The adjustment spec on the pedal is .8" to 1.2". Which dimension should you keep it closer too? Or should you just try to keep it in the middle?

The deck clutch has been failing to engage intermittently. It failed yesterday and I couldn't get it function properly again. I have tested yellow switch at the connector to the clutch. With a meter on ohms, the open circuit will change to 0 ohms when the switch in pulled up (energizing the...

Hi all If anyone happens to have or know where I might find a clutch bearing hub for my MT250D part number 1021 1115 002 new or used then can you please let me know, or evan have a drawing with the dimensions so I can get one made Regards George

Several years ago I bought my Yanmar YM2310. My previous tractor purchases were a Case 580 CK and a Ford 9N. I had no experience with tractors made for rice paddy work. The seller told me that the tractor had not moved for 2 years and that the clutch was stuck. I got it started and drove it home...

I have a Bolens 1668 that’s been working great for me. Last week I was mowing, then I shut the pto off for 30-45 seconds or so, and it didn’t engage when I tried flipping the switch. Upon further inspection, I found the pto assembly was very hot. Once it cooled down, it turned back on without...

Jumped on the old Yanmar, it’s been a while, and the clutch would not disengage to shift. Figured stuck clutch, ran it around trying to unstick it but no luck. Clutch pedal felt very easy? Decided to just get a new clutch kit and fix a few other leaks while I have it down. Pulled the motor...

Hey all my name is William and I'm new here. I bought this tractor last spring for my small farm. Other than typical farming stuff I've mostly been doing some logging for my sawmill side gig. But at this time I have an oven on wheels. My compressor clutch is not turning/engaging and the blower...

Hello to the brain trust.....New Holland TC33DA hydrostatic had a bad clutch. Got inside and found oil in the clutch housing and this(photo) what in the hell does anyone think it could be. Def signs of mice around the tractor but this is so consistent one thing almost looks like it grew there...

I recently bought a tractor and it seems the pto clutch is burnt up. Is the pto clutch internal? Is there anyone who has any insight on this issue or a service manual for this tractor?

Been having intermittent clutch problems. Slipping, not able to go into gear, nothing consistent. Finally decided to split the tractor. Although showing wear, the clutch and pressure plate seemed OK. What I did find was that the "hub" that connects the throw-out bearing to the pedal forks seemed...

I have purchased a used TMG tiller I serviced it today and ran it for the first time. I’ve never run one before so I have no experience with one. So while running it for a test I noticed when running into some coastal Bermuda the clutch slipped. It made quite a racket so I lifted it a bit to re-...

All, Is there an online parts look up that I might be able to search for parts on for a 185 hydro? I believe it is a 1987 model. The electric PTO clutch is out. I've done some initial diagnostics and have narrowed it down to the clutch. I have not removed it, so it is conceivable there is a...

My son noticed this too. If the tractor is stopped then when the clutch is let out the tractor will start to move in the opposite direction of where the shifter is. Just slightly. So if the tractor is in reverse when letting out the clutch the tractor will move forward, just a bit. And when in...

Hi all fist post. I use this site a lot. My father borrowed my cx2510 hydrostatic when I was on vacation and was using the clutch like a stick shift. 😵‍💫 he said he would hear grinding and asked if it was normal. What kind of damage could he have done. Thanks

So i have tried to change the clutch on my iseki tx 1300. And when i put everything back together the clutch will not completly disengage. I can turn the wheels barely with the clutch pedal pressed down and in a high gear. Tok everything apart and noticed that the pins on the clutch had been...

After doing some research on my new machine it apereas that many of them were incorrectly assembled. the brake and clutch rods are reversed. crossing each other in A X type pattern. this is incorrect. after repairing and adjusting that situation, also main clutch was way too tight with no...

Doing my annual clutch slip on my land pride rcr1260. Marked the plates, ran it and one plate moved, two stuck together. Did this a bunch of times with the same result. I did notice the last time that the two stuck together were in a different position relative to where the spring assembly...

Does anyone know how the heck this front drive shaft for a Ford 3910 comes apart? I see no slip yoke or anything normal. The front has some airplane wire retaining screw thing. I can find nothing online and the manual set I have only shows how to split a 2wd not 4x4. It’s the last thing I need...

Afternoon, I recently acquired a bush hog (potentially a Woods model, unsure) and am experiencing issues with repeated sheer pin failures when using it with my Kubota M6040 tractor. Initially, the sheer pin would break quickly upon engagement. I then loosened and cleaned the slip clutch, and...

Good day; Edit: I was so sure it was going to be something complex that I neglected to check the simple stuff first. Turns out a blown fuse was the problem. Lesson learned! NH TC30 won't turn over. New battery. Cranked briefly (maybe a second) when I went to start it earlier, today, then...

Hello! I have a Deutz-fahr 4070E tractor. My clutch pedal spring broke so now i don't know where it attaches on the pedal side. I can see the hole on the chassis side(the static one). I need the diagram so i can attach it without removing the whole fuel tank! Thank you!

hi guys nubbie here i got a issue with Kubota b6100 .....i bought it knowing the throw-out bearing was making a sound and the clutch would not disengage , i took it apart and decided to replaced the clutch, throw-out bearing ,pressure plate ,pilot bearing .reinstalled and the clutch would not...

My 1720 has 475 hours on it. It was parked outside for 13 months not being used. Now the clutch will release the pto but not the drive clutch. Any suggestion before I have someone split the tractor into.

What do you use your clutch for...on your HST tractor...just for engaging the PTO? Or do you use the clutch for other operations?

IH D40 clutch stuck after parked a bit. Last time this happened I spent 5k for a new clutch. I had no clutch after parked in weather a while. I oozed it to a sloped back driveway and put my f150 in front. I tried yanking with clutch blocked. I heated it up by 30 min high idle. Tried again no...

Unfortunately I left my 870 clutch up (not depressed) for a couple of weeks and it is now "frozen" where it will not engage. I warmed the tractor up for half an hour but it still would not release. I banged it into first gear and drove it around a bit and that did not free it up. I was able to...

This is my first post on this forum. I just purchased a 2005 Zetor C42L. From what I have read it is the same as a Branson 4220 aside from the FEL. The machine is in great condition and everything seems to work properly except the second stage on the clutch. When the clutch is pressed all the...

Looking for the best place to find a replacement clutch drum(sprocket)

Does any one know if it is possible to put a twin disc clutch in place of a single disc clutch in a 275 massey , ive waited a long time for parts to arrive and theyve sent me a double disc set up , i will need longer mounting bolts and im aware the pto will disengage differently . But would the...

I just bought a Mahindra 6075 and I have been told that the dry clutch should have a weep hole on the bottom of it and I can't seem to find it. The mechanic told me that I should drill one myself, but I'm confused because wouldn't Mahindra have put one in if it needed it? I understand that...

Today, my 2000 Kubota L2500, when pressing the clutch, it makes a squealing sound. It has never done that before today. Any ideas?

Hello! My Case IH STX 450 doesn't move. At first, the error code was 56016. We took out the potentiometer at the clutch pedal. There is 8 volts in the wire. If we reinstall it, we can't calibrate it. The star (*) does not appear on the calibration display. However, if we take it out and use a...

Hello! My Case IH STX 450 doesn't move. At first, the error code was 56016. We took out the potentiometer at the clutch pedal. There is 8 volts in the wire. If we reinstall it, we can't calibrate it. The star (*) does not appear on the calibration display. However, if we take it out and use a...

I recently purchased a 2006 Jinma 284. Among other items I found that needed correction the wires for the clutch safety switch were hanging loose. I purchased a new switch but can't find the original switch or mounting location. If someone could provide the location where the switch should be...

Is there a best "easy" way to replace the clutch pedal return spring on a 2005 NH TC29DA tractor?

I have mf185. Just replaced clutch plate and pto clutch. Been all good about 1month. Now when engage pto, the tractor become slow... and run as normal when turn off the pto. What should i check ... can anyone advice on this.

My question is. - If I'm going down a step hill carrying a load in my front loader bucket. ' If my back tires come off of the ground, will I still have brakes on the front wheels? I have some fire wood at the bottom of a steep hill I'd like to get. Thanks This is the Massey Ferguson 1739E...

I have been through the wringer trying to source decent price and available parts to rebuild the E3CD-T in my M-F1440V - and after a month or so (see my posts in M-F forum IIRC) think I am ready to order final lot and put it back together. With a mighty 420 hours on the clock I would not have...

I have a wallenstein fx85 winch I have been using for about 10 years. Has been trouble free except once for a stupid mistake I made myself😂. Recently it developed an issue occasionally. On a hard pull when it maxes out, stops pulling, the clutch sometimes won't release when I release the white...

TC33D NOT HST(1999-2001). My clutch pedal will press to the floor without disengaging and with little to no resistance. Trying to find a parts diagram so I can see what is what. I know I have a broken return spring for the pedal, but with the pedal NOT disengaging when depressed, my best guess...

Hi all, I have changed the clutch on my cx90 a few times over the years. The last two times the clutch wasn't badly worn at all. It's currently not great at all and hard to get into gear. Here is what's happening. With the clutch fully pressed and shuttle in forward or reverse, when I try to...

I recently split the tractor and removed the worn clutch. Shopping for clutch's, throw out bearings, gaskets, etc. Can anyone recommend a website or parts store? Google search for 1920 brings me to ALOT of sites, mainly eBay. Be nice to hear someone else's experience on this. Also, I'm...

Hello, Does anybody know how to replace the external Clutch Pedal Spring on a Ford 3600? Part# C7NN7N98A

I have two sons who will be using the machine and I know how dangerous tractors can be so I want to install a Clutch Safety switch. I need help figuring how how to wore it in to the system. I have already mounted a switch system from a YM240 on the unit.

Hello, My ford 3000, clutch seems either worn or out of adjustment. When I depress it, it is not engaging, and won't go into gear. Are these hydraulic? Also how do I adjust? Any info is much appreciated. Thanks

First let me say, obviously I didn’t grow up around tractors so forgive my ignorance. As I said I have a NH 3930. Been using it for about 10 hears to bushhog my grass pastures. It is level ground but I do have patches where the weeds or noxious grasses are thicker. Also has a some obstacles like...

My Mahindra 2545 HST will not move under it's own power. Almost seems like the clutch went out. What can I do to troubleshoot this before taking it in to a mechanic and finding out I need a new clutch? It has 85 hours on it and I bought it a few months ago with 75 hours on it. I do not know...

I have a Branson 3510i that had a bad throwout bearing. I was able to split the tractor apart. I wanted to have the flywheel machined before reassembling but the flywheel has a secondary damper disk (similar to the damper spring assembly on the clutch disk) that covers the bolts that fasten the...

I've got this Gator. Belonged to wife's cousin next door so I know most of its history. There doesn't seem to be ANY tag on it with a serial number so I'm blind to that question. Embossed under the passenger seat is what appears to be: W00? (B or 8 or maybe P) X4X073915 Long story...

Hy all. I am new to this forum and new owner of an BCS 735 with Acme ALN330wb engine. (I think this is model, i will attach picture with serial) Please help me with the following: Bcs doesn't seems to react when pushing on the clutch. The gears are stiff and engaging with "bad sounds" and even...

Have a Case IH Farmall 31 that has a whinning noise when you release the clutch pedal. Once the pedal is depressed the noose goes away. I just split the tractor and replaced the release bearing.

Hi I have a Belarus T40 tractor that I am installing a new clutch in. I am at a loss as to how to replace the release bearings for the PTO clutch and the Main clutch. Any help would be most appreciated

Hi - I have isolated a problem with my main 30 amp power fuse having been blown on my tractor. It looks like it is the PTO clutch. With nothing running and just pulling the PTO switch on, I hear the PTO clutch solenoid clicking on and then off when I shut it off. But if I leave it on for about...

This is the third time that this tractor has been split to replace the clutch due to release (throw-out bearing seizures). I am wondering if any other tractor owners have experienced similar troubles? It only had 200 hrs. when the first one happened. Then 400hrs and now at 1109 hrs. Every time I...

I recently got an old David Brown 1210 as a barn find. Hadn’t been used in 20ish years. Did some basics to it and got it home. Clutch was working fine. The next day, I went to move it closer to the shop so I could do further maintenance before actually using it. I put it in 1st and started to...

Hey folks new guy here. I bought a Rhino Model 72 shredder from my neighbor. I haven't used it yet but he said it works great. However, I don't think the clutch assembly is correct but I cant find anything on line showing the proper configuration. I carried it to a local tractor parts store...

I'm wondering if anyone has had the PTO clutch pack out of a 4.105? Any "do this" or "don't do that" sort of things one needs to be aware of?

So i have 2008 3520 hydrostatic with cab and have been experiencing a problem with the rear pto. Was using my NH teader rakeand noticed it was slowing down and almost stopping on rough ground. The rake does not have a clutch so it looks like the pto clutch is slipping. I have not done any more...

I have a couple clutches on implements and was wondering how folks go about adjusting theirs. On mine I use a point and shoot thermometer. I run the implement hard and see that the clutch warms up some indicating a slip. Then back down the load and see that it cools again. When my brother...

Went to adjust clutch on mahindra 3505 di. Lossened 2 bolts turned the adjuster 1/4 inch completely lost the clutch. Tractor has a duel clutch system. I'm doing something wrong and don't know what it is. The adjuster rod would only turn one way counter clockwise and only 1/4 inch. Anyhelp would...

Have a TYM T430 that we use quite often, was out with it a bit ago, and all of a sudden the clutch would not disengage. the clutch pedal still feels like its working normally, but the tractor just keeps moving. We have tried adjusting as much as possible with no change. we are able to get it...

Not sure what’s going on. Clutch locked up today during weedwacking. I bumped a couple of rocks kind of hard. Not sure if that caused it. Didn’t notice until I went to put more line in it and the head didn’t turn freely. When I pull the starter cord, the head turns. Any ideas?

Kubota L4610 HSTC, 4200 hrs, My AC clutch is dropping out, even though it has current to the wire entering the compressor. Happens most often after has been working fine for a while. Likely getting hotter, although engine temp is fine. Some times it will cycle back on for a little bit, then back...

Got tall grass wrapped around and now the seal is leaking. How big of a project for 2 people, advice and suggestions?

Condensor clutch not engaging

I do all my own mechanical work but have never done a clutch replacement. So any advice would be greatly appreciated. Are the after market clutch plates comparable to the OEM? Where is the best place to purchase a clutch kit? I know JD dealers are good but they want an arm and a leg for parts...

I was working my farm road on a hill the other day and I pushed in the clutch to let my tractor roll freely backwards. I heard a pop and the clutch disengaged. The exterior linkage to the clutch pedal is fine, so whatever went is inside the bell housing. The clutch presses and releases...

I could tell something was fishy long about my 2nd bushhog shear pin. The PTO clutch pedal won't disengage the PTO. All I've done so far is observe the clutch linkage which appears to correctly be moving the clutch lever on the transfer case about 1", maybe less...there's not much room for it...

i have a 2013 powerstar with power shuttle and 8x8 gears. i hooked up planter and main gears ended up getting stuck. i ended up switching gears and started planting. Well after about 5 acres the clutch pedal started to rise up slowly and tractor seemed to slip gears. I stopped and hydraulic...

how do you adjust theclutchona RhinoInternational 344

Hi. Does anyone see a way that some lube could be applied/sprayed onto the throwout bearing without splitting the tractor? The clutch is working fine but the bearing is dry. I can hear it coasting down when I take the tractor out of gear, release the clutch, and turn the engine off quickly. It...

My dad just bought a 2014 6140d with cab and a loader from a dealer. It has about 1820 hours. Having some issues possibly with the transmission, clutch or brakes. It has the 12/12 power reverser. This may be a little hard to explain especially without a video. When I push the clutch all the...

I have a Farmtrac 665 DTC (shuttle). The clutch does not disengage fully. I have adjusted it and the tractor will not stop. The clutch does not appear to be slipping nor does it have a smell. The tractor seems to pull okay, but will not disengage. Any suggestions.

Looking for any assistance from anyone who has been able to source/replace Howard 2000 early 70's 3 hole clutch plates. Replaced my motor and now clutch won't engage so I'm guessing plates are too worn. Any help is much appreciated.

I've owned this tractor for 17 years and have never used the PTO until now. I recently bought a post hole digger and have come to find that the clutch won't disengage the PTO. With the clutch fully depressed I engage the PTO lever and the PTO shaft will turn even with the auger hitting the...

Hello everyone, I am new here and I hope you can help me with the following problem A few days ago, immediately AFTER switching on the PTO to drive a disc mower (rear) our renault 540 rx ares gave up. What no longer works: - driving forwards or backwards - PTO no longer works - power...

I have a Yanmar YM1500. Ordered new brakes and seals to deal with the oil leaking into the brake drums, now I'm ready to tackle the clutch issue. The clutch doesn't fully disengage. I adjusted the pedal and there is still more adjustment to go, but when I push the clutch in it just keeps...

I need to replace a clutch in a 250as and would like to know what the finger height should be when installed. I could not find it looking at the manual, only peddle adjustments. Thanks

Well, it's come time to replace my tractors PTO clutch assy. The PTO clutch has called it quits and now I'm having to split my tractor and replace it. It took my dad and I around 4.5 hours to drain everything and lift the cab off then split the tractor midship and pull the PTO clutch out and...

Ref: Dual Clutch Align and Setting tool (07916-90052). B2150D 4WD Manual Gearbox. Hello and thanks for taking the time to read this post. I am in the process of changing the dual clutches on my B2150D 4WD Manual gearbox - currently waiting on parts - and will need to align and set the discs...

I have a little Branson 2810 (28hp) which I bought new in 2002. I really like it but it has given me (so far)an unsolvable clutch issue. I have posted this issue in the Branson thread several times over the years as I have tried resolving the it. I have talked to various dealers also. I am...

My rural king tiller has a slipper clutch on it. Before using it i loosened it up and burnished the clutch surfaces. Tightened it back to where it was set and put a line on it with a paint pen. Tilling food plots today breaking fresh ground i hit some goobers. Enough to bog the tractor and make...

i have a 1944 ford 2 n my issue is cant get into gear Just grinds Tried adjusting no sucess..it also has a sherman trans .. I did notice leaver coming trans that clutch rod connects.. U can only move leaver 1 to 2 inches Any idea guys...is it struck or shot...btw im 80 yrs old...not lookng...

i have a 1944 ford 2 n my issue is cant get into gear Just grinds Tried adjusting no sucess..it also has a sherman trans .. I did notice leaver coming trans that clutch rod connects.. U can only move leaver 1 to 2 inches Any idea guys...is it struck or shot...btw im 80 yrs old...not lookng...

I have an old Howard rotovator rototiller (Model HN) with a 12 compression spring twin disc pad slip clutch. I had to replace the friction pads recently but found that the metal plate between the friction disc pads is deformed (no longer truly flat - see pictures). As a result one of the new...

I have a MF135 that I'm into a hydraulic pump/ PTO clutch repair on. I'm having trouble figuring out how to remove the hydraulic pump/ PTO clutch and it looks like they have to come out together? Any know-how appreciated.

On a NH Ford 445C, how to adjust clutch with an electric foot pedal?

Does anyone know the clutch adjustments for a mahindra 2525? Just replaced drive and pto clutch plates and need to know clearances. Thanks

I am looking for pto clutch springs for a 48" HOWARD rotovator . All the tractor dealers want to sell a complete PTO shaft/clutch assembly. Does anyone know a source for the springs, or am I condemned to buy the complete assembly?

How do you repair a slipping clutch. It's fine on flat ground and doesn't Slip at all but going up a hill and it slows down.?

Buying a 9/2005 Foton FT254A sight unseen except for a few pics. I'm told it needs a clutch. Very limited info online that I have found. I did purchase a parts manual but can't find a service spec manual or online English resources. I see there are 2 clutch options for parts. A single stage or...

Hello I am trying to fix a "PTO popping out of gear" issue whereby the PTO will stop spinning as the lever kicks back to "off" If I hold the PTO lever down it will stay engaged, but I can't seem to adjust the lever detents so that they will hold. I am about to remove the linkage housing so I...

hey all, I have a 2004 ck 20 with 500hrs. I'm the 3rd owner and the machine was used for snow clearing with the FEL. I installed a rear mounted snow blower and love it. I was having a starting issue and resolved it with a starter rebuild and a new battery cable to the starter. I don't think the...

good morning everyone, After a long day of bush hogging, I noticed a small drip of rear end oil leaking out of the washer around the break/ clutch pull rod on the left side of the rear end, I loosened the nuts and pulled the washer back to clean everything up and made sure to...

I'm about to embark on trouble shooting what I think is my clutch since it doesn't seem to engage much and then only in low gear. Anyone have any tips on what to look for or where to best get a replacement clutch before I split it open?

I bought an older b1750 HST 4x4 a few months ago. I had been using it with no problems and backed it up to my tiller one evening, thinking that I would hook up to the tiller in a day or two. Although I had no problems when I parked it, I went to get it and hook up to my tiller but after I...

I owned a RX6010 cab and had the clutch cable break at 215 hours. Since it shut me down for 10 days, I bought 2 clutch cables, one as a spare. I no longer own the tractor and would give someone this cable.....but won't bother shipping it. Pick up in Southwest Missouri. This cable seems to be...

Adjusted freeplay on my kioti ck30 clutch pedal to an 1” of freeplay , now when I press clutch it feels like a second engagement about an 1”from the floor , tractor goes in gear alright and when I release pedal , seems like it engages in gear at the 1” from floor and goes ahead , more aggressive...

Bought a 301A over a year ago that had been setting along time turns out all I needed to get it started was a new fuel transfer pump and rebuild the starter ….... everything seemed to work well except the rear lift arms wouldn't hold a middle position no biggie ran for a bit but I noticed was...

Hi all, does anyone have the correct resistance number for the clutch solenoid RE177539. having issues, but want to make sure before I buy a new one. thanks in advance paul

I'm going dane dane dane.....am I gonna have to split this thing? I've got a Massey 1020...luv the little guy, done great service for me. Today I jumped on, it was in First gear slow mode, the clutch was pressed in, started the tractor and there she was moving forward on it's own!! No matter...

Clutch became too easy to depress and wouldn’t go into gear. With engine off, putting tractor in gear and then depressing clutch pedal and turning key, tractor lurched. I assume clutch is shot. How tough is it to replace? My local shop is $67.50 an hour plus $200 for pick up and drop off. If I...

i have a john deere 301 a tractor that when trying to engage the rear pto depressing the clutch does not disengage the pto drive and it doesn't allow you to flip the pto lever to the on position. pushing the lever forward only causes it to grind gears, the clutch works fine for the transmission...

I have a s-373D and all of a sudden it will not shift into any gear. With the engine on and the clutch depressed I hear grinding when I try to shift into a gear and am unable to shift into any of the gears. It is the same sound and feel as with out the clutch depressed. The PTO is functional. I...

In the process of replacing the clutch in my LK 3054. The hour meter reads 430.0. My buddy gave it to me because it would lose forward power while going up hill and he is not a mechanic. When i got it, the situation got even worse and the tractor got to the point where it could not move while...

Hi folks I have just picked up a Mitsubishi S3L2 engine that came out of a Boomer 24. I’m thinking about installing it in a tractor that has a regular clutch. The boomer was an HST machine. The flywheel is drilled, seemingly for a clutch. Can I install a clutch on that flywheel? I have the...

Good afternoon all! I have a JD 950 and need to replace the clutch (wasn't running when I got it and doesn't yet...). Serial #CH0950-SO-18873, and according to Tractordata.com it's from 1983. I've seen on this forum somewhere that they used a dual stage clutch beginning in 1984. Can anyone...

What's the easiest way to change the clutch please? I'm thinking the easiest is probably pull the radiator and move the engine forward. Or is there an easier way? The tractor has a sub frame assembly for the front end loader and rear back actor. Also... Whats the part numbers for the following...

Bought a used tractor with only 120 hours. However, after about 5 to 10 minutes of running tractor (after it warms up?) it starts grinding when it goes into gear. When this happens, when I push in the clutch it makes a chatter like it's making something spin and will grind if I try to put it in...

I am in need of some assistance. I had to rebuild the t96 3 speed transmission which was a piece of cake for the most part. I also had the flywheel resurfaced and got a new clutch kit. The clutch kit came directly from the clutch factory and not through Vermeer. I installed it and it seems like...

I'm new to large farm tractors, so please go easy on me. I bought a Ford 8600 back in August of this year. One of the rear remotes hydraulic line busted and gallons of fluid spewed out. I had to move it approx 50'-60' to get it out of the way from where the hose busted. I got sick and it...

Hi, recently the clutch on my 6340 started to leak, dripping from the pedal inside the cab. Any of you ever have the same problem? Thanks

Hi Everyone, I have an Apollo 354 tractor. It does everything I need around the farm - but the clutch is getting to be hard work to operate. Bucket work is becoming a bit of a chore due to this. The clutch mechanism etc is just the same as it has always been and works fine - it's me that's the...

I have a clutch stuck on my Mitsubishi 2wd tractor. I have tried to start the tractor with the clutch pushed down, I drove it around for a couple hours and it never disengaged. I tried different gears, gave lots of gas and hit breaks. This has work previosly. I would love to avoid splitting...