Well pump/generator question

   / Well pump/generator question #1  

1930

Platinum Member
Joined
Sep 9, 2018
Messages
920
Location
Brandon/Ocala Florida
Tractor
Kubota B6100E Kubota L 2501 Kubota T1460
Can someone tell me which side of the generator I should be plugging in my well pump. Id assume the left. That where I get the power for my camper a/c.
 

Attachments

  • 20200523_204422.jpg
    20200523_204422.jpg
    5.2 MB · Views: 162
   / Well pump/generator question #2  
It depends on the voltage your pump uses. 120 or 220 and the amps it pulls
 
   / Well pump/generator question
  • Thread Starter
#3  
No idea. 1.5 h.p pump. I was told 220. No booklet no nothing
 
   / Well pump/generator question #4  
For that size pump, 220V makes sense, Wire colors for a three wire Pump are usually Red, Yellow and Black. Two wire Pumps have a Red and a Black. If you have a Yellow and a Red, you have probably not yet located the Black wire. It may be broken off in the Well. So chances are you will have to pull the Pump to make repairs anyway.
 
   / Well pump/generator question
  • Thread Starter
#5  
I hope this helps
 

Attachments

  • 20200523_213419.jpg
    20200523_213419.jpg
    4 MB · Views: 171
   / Well pump/generator question
  • Thread Starter
#6  
Only 2 wires and a ground attach to pressure switch
 
   / Well pump/generator question #7  
Control box is for 220V....

AIM Manual - Page 54 | Single-Phase Motors and Controls | Motor Maintenance | North America Water | Franklin Electric

Will wire to the 220 Volt twist lock on generator.....

35a6321a93ba4ee8172e07dbbed62c42.gif


You will need a L14-30P (plug) for end of cord at generator...

You will ignore White Neutral and just connect to Line 1 and Line 2 and safety ground...

Pressure switch it should just be wired in series between generator and pump controller...

index.php


IF you don't have complete understanding of this, get help....

Dale
 
Last edited:
   / Well pump/generator question
  • Thread Starter
#8  
Control box is for 220V....

AIM Manual - Page 54 | Single-Phase Motors and Controls | Motor Maintenance | North America Water | Franklin Electric

Will wire to the 220 Volt twist lock on generator.....

35a6321a93ba4ee8172e07dbbed62c42.gif


You will need a L14-30P (plug) for end of cord at generator...

You will ignore White Neutral and just connect to L1 and L2 and safety ground...

IF you don't have complete understanding of this, get help....

Dale
Ok so outlet on the right. I was wrong.

Ignore the neutral. Thank you for the help
 
   / Well pump/generator question
  • Thread Starter
#10  
Very little signal. If it hadn't been for dl I wouldn't have water. Above and beyond. Have no idea how much appreciated
 

Tractor & Equipment Auctions

2018 KENWORTH T370 T/A DUMP TRUCK (A51406)
2018 KENWORTH T370...
Quick Curbs (A49461)
Quick Curbs (A49461)
2017 Ford F-450 Crew Cab Knapheide Service Truck (A49461)
2017 Ford F-450...
2025 Swict 78in Bucket Skid Steer Attachment (A50322)
2025 Swict 78in...
REYNOLDS 100 - 8 YARD PULL TYPE SCRAPER PAN WITH DRAWBAR (A51039)
REYNOLDS 100 - 8...
Caterpillar D5K2 LGP Crawler Tractor Dozer (A50322)
Caterpillar D5K2...
 
Top