Might give that a try, Not sure how bad that would lay the grass over as that is another issue, Grass in the wheel tracks is not being cut well......
Flail Mower Let's talk flail mowers
- Thread starter TNhobbyfarmer
- Start date
- Views: 3287864
Might give that a try, Not sure how bad that would lay the grass over as that is another issue, Grass in the wheel tracks is not being cut well......
Xfaxman
Super Star Member
- Joined
- Feb 8, 2013
- Messages
- 12,887
- Location
- Guthrie, OK
- Tractor
- Toolcat 5610 G - Bobcat V417 - TORO+Loader
The knives on my TORO out front 5' deck are sharp on both sides, like most are. When dull you can remove the shaft and turn it around to use the sharp edges. :thumbsup:
hunt4570
Elite Member
- Joined
- Feb 10, 2015
- Messages
- 4,059
- Location
- South Carolina
- Tractor
- Grand L3540 ,724 loader, bucket, grapple and now forks also! And just for OP.. a pool!
Let's wait to see what Bill Murray says. He's the one with real world experience.
He's dead... didn't you see Zombieland??
IslandTractor
Super Star Member
- Joined
- Sep 15, 2005
- Messages
- 15,802
- Location
- Prudence Island, RI
- Tractor
- 2007 Kioti DK40se HST, Woods BH
The front edge of the mower will lay the grass over anyway. Most of us don't have a problem with that even with very tall grass.
IslandTractor
Super Star Member
- Joined
- Sep 15, 2005
- Messages
- 15,802
- Location
- Prudence Island, RI
- Tractor
- 2007 Kioti DK40se HST, Woods BH
Haven't seen it. Is it worth renting?
hunt4570
Elite Member
- Joined
- Feb 10, 2015
- Messages
- 4,059
- Location
- South Carolina
- Tractor
- Grand L3540 ,724 loader, bucket, grapple and now forks also! And just for OP.. a pool!
Yeah, its a fun little movie, more comedy than horror..
Get FIDO while you are at it, another good one. YMMV
Poopdeck Pappy
Elite Member
- Joined
- May 13, 2013
- Messages
- 2,627
- Location
- Dallas, Texas
- Tractor
- Kioti DK50SE Cab, Kubota BX23, Kubota BX2660, Grasshopper 729BT
That's why your flail isn't performing satisfactorily. You don't have the secret decoder ring. :duh:
hunt4570
Elite Member
- Joined
- Feb 10, 2015
- Messages
- 4,059
- Location
- South Carolina
- Tractor
- Grand L3540 ,724 loader, bucket, grapple and now forks also! And just for OP.. a pool!
OMG!!! Run everybody run... he's not a member!!! AHHHHHHHHHH.......
leonz
Super Member
AHA,
You my dear friend have what is commonly referred to on the beer garden porch at the border crossing as "Altitudus To Highus Raiseus FlailMowerUs disease my dear fellow Flail Mower Nations Citizen.
Lower the cutting height one inch and go over it again.
Your flail mower rotor is not creating the Pressure Gradient needed being "suction lift" as the mower shroud is not close enough to the ground to provide enough resistance to pull air through the front of the flail mower.
If you can lower it to one inch great if you are confident the side slicer knife blades will not bang the sod too much.
You my dear friend have what is commonly referred to on the beer garden porch at the border crossing as "Altitudus To Highus Raiseus FlailMowerUs disease my dear fellow Flail Mower Nations Citizen.
Lower the cutting height one inch and go over it again.
Your flail mower rotor is not creating the Pressure Gradient needed being "suction lift" as the mower shroud is not close enough to the ground to provide enough resistance to pull air through the front of the flail mower.
If you can lower it to one inch great if you are confident the side slicer knife blades will not bang the sod too much.
