pto

I am having an issue getting my PTO to shift into gear. In fact I broke the arm (PTO Rod) that goes between the shift lever and the actuator trying to get it to shift. After the arm broke the shift lever moves up & down freely, so it has to do with the PTO Shift Lever Shaft or something...

Hello, I'm needing a service manual for my 2006 Montana 4940C tractor. I'm having PTO issues. Thanks. My email is mtwz71@yahoo.com

I have a BX2200 that is leaking around the control arm for the pto at the transmission. I'm trying to remove the control arm to replace the o rings and have removed the bolt that goes thru it and the shaft and it will not come off. I don't see anything else holding it on and the service manual...

I have an old Howard Rotovator rototiller with a 12 spring twin disc slip clutch instead of the shear pin type Universal Joint. A month or so ago the clutch started smoking. I adjusted the compression springs however since then my PTO spins normally but the rotor only spins above the ground...

I have spent a lot of time searching for the problem and I am convinced it is in the wiring harness. I have wiggled the wires under the steering wheel and gotten the pro to stay on for awhile then do it again when it stops. I finally wired a toggle switch straight to the clutch and fixed the...

Hey guys, running my Mahindra 2538 HST pretty hard today and all of a sudden I heard a small pop and noticed hydraulic oil pouring out. I was able to drive it back to the garage after adding some fluid, but still leaks pretty bad. It appears that the leak is coming from the flare on the pipe...

I am looking for pto clutch springs for a 48" HOWARD rotovator . All the tractor dealers want to sell a complete PTO shaft/clutch assembly. Does anyone know a source for the springs, or am I condemned to buy the complete assembly?

The splines on this shaft are destroyed and I can't work out the proper way to remove it I've removed all the circlips and when I pry on the shaft the bearing and shaft want to come out together My concern is that once the outer bearing is out of its race I won't have a way to remove the inner...

Anyone have experience with the PTO Link Systems? If so, pros and cons? https://tractorptolink.com/shop/

I need to replace my driveline guard on my woods BB60 brushbull. Name on the old guard says Agmaster-11. I believe this is a Waltershield. Bought mower in 2005, if that makes any difference. My question is where is the best place to get a new one? Places I looked at,I couldn't believe the prices...

Last year my PTO clutch started slipping. I tried reading pressure on the back of the transmission where the hydraulic lines go in and had zero psi. Port g2 on the pto valve block and the port in the back of the transmission have the same pressures. The next step was tearing apart. I was able...

I have an old Howard Rotavator Selectatilth that is missing the pto shaft and slip clutch. Does anyone know where I could find one? The shaft coming out of the gear box is 1.5" and has 10 splines. Also if anyone know what model this is that would help. The factory tag is missing. There is a...

Was engaged brush hogging and just stopped spinning. I had been doing some thick stuff earlier in the day but at the time it was mostly just broom straw. Light is on just no rotation. It's the compact 34HP 1250. What should I be testing first to troubleshoot it?

Today I was using my tiller and the PTO won’t disengage. When I move the lever to the disengage position the cable just goes slack. I can go under the tractor and with just a little finger pressure move the lever to the disengage position, but then when I re-engage I have to crawl under and...

Hi. I am new to this forum and I need help. I have a 2008 Massey Ferguson 2625 four wheel drive tractor with independent PTO. When I turn the PTO on, the 3-point lift arms stops working. It has a new Hydraulic filter, and new oil. I am getting 2350 lbs. of pressure at 3-point lift arms test...

Hello I am trying to fix a "PTO popping out of gear" issue whereby the PTO will stop spinning as the lever kicks back to "off" If I hold the PTO lever down it will stay engaged, but I can't seem to adjust the lever detents so that they will hold. I am about to remove the linkage housing so I...

A friend bought a 50" Landpride tiller at the Kubota dealer. We used it this weekend but I was not super impressed with the depth it was able to till to. We used a ripper to rip 3 4' wide by 40 foot long rows. We then added some Compost and went to tilling it seems like the tiller only tilled...

I was just greasing up the rfm getting ready for the first mow when I noticed the plastic safety guard on the pto shaft mangled in the middle. Looks like the shaft is coming into contact with the drawbar when the tractor breaks over a hill. I was able to get it apart and shorten the inner...

Is the left side lever between your knees on the floorboard only to be moved with the tractor turned off, or should the right lever in N allow that lever to be switched back and forth? Trying to decide if my tractor isn't acting right or that I'm the one that is messed up? I can't go from pto...

I bought this 185 lo boy as a project for the winter. It had broken belts from the engine fly wheel to the pto driving shaft. After replacing the belts and starting the engine, there is a terribly loud noise from that area. I think that the bearing in the assembly that adjusts belt tension is...

I have a Long 2460 tractor and the PTO grinds when I try to engage it in either syncro or independent. I do have the PTO clutch rod lifted when trying to engage it. I have adjusted it until it hits the clutch lever on the side of the tranny. The PTO clutch lever is bent slightly down. I am not...

Mahindra Max-24 This seems a silly question, but I am missing 2 bolts that hold down what appears to be a spring-tensioned-band, located underneath the seat pan cover plate, and behind and above the rear PTO assembly. The band when unbolted sits at a 45-degree angle and requires a bit of...

Hi, I am new to bobcat, all my tractor before (Massey and Mahindra) had neutral PTO, meaning that when the pto is not engaged, the PTO shaft was easy to move around, so you could align the splines with the attachments to make connecting very easy. What a surprise when I tried to connect an...

i have a john deere 301 a tractor that when trying to engage the rear pto depressing the clutch does not disengage the pto drive and it doesn't allow you to flip the pto lever to the on position. pushing the lever forward only causes it to grind gears, the clutch works fine for the transmission...

Hi all, First time poster here. I just recently bought a second hand Kubota M9540 for some property I have in the Bahamas. Its a bit of a working hobby farm and having a tractor is new to us everything has been done by hand so far. So I'm kind of like a kid in the candy shop right now finding...

I became responsible for running a JD 4020 with plow and snow blower. I cannot tell the make and model of the snowblower, I just know that it's about 5 feet wide. My quandary is that the sheer pin went on it, and it's not straightforward how to install a new one. I have enclosed a sketch of the...

I have a 1999 Kioti LK3054 whose manual states it has 30.5 gross horsepower, does anyone know or has tested the actual PTO horsepower? Thanks in advance, Glenn

Annnd I am back... Ok got some strange things afoot with the 2440...When the PTO is disengaged, center lever down, I am having hydraulic issues. The Power steering will only work intermittently with High RPM's, and the rock shaft will do the same it may or may not go up with the higher RPMS...

Hello all, I just purchased a Yanmar 155d with a loader and a brush hog in good condition about a year ago! Paid $3750 for it, in case anyone might be wondering, and honestly feel like that was a very fair price. It's been running great (save for a blown hydraulic hose on the bucket, but that...

The PTO lever on my 1086 is hard to engage. Any suggestions on what is wrong and how to fix it?

I have an MT4501D that I bought at auction a few weeks ago. Tractor runs strong. PTO did not engage at first. I raised and lowered the 3 point with weight and the PTO started to spin strongly. I attached my 5ft tiller. It took some time to start to spin the tiller but does so until I try to till...

I've been busy with PTO tiller attached. I had two safety chained hooked up and heard a clank during using and found one of my chain laying in the dirt -- the clip was bent. There must have been quite a bit of force to break that clip. Should I be concerned or just get a new clip and hook it...

I recently picked up a sickle mower for my BCS 722 at auction. I haven't used a front attachment with PTO before on my tractor, and after moving the handle back over the motor, the locking mechanism is still engaged preventing me from using the sickle mower. Is there some pin or other mechanism...

Good day, I am running a logging implement on my NH TT4.90, and the unit is rated for 3000 to 3500Nm of torque (at 540rpm), while the tractor engine torque produced by the tractor at 1400rpm is 340Nm. I assume there must be a material increase in torque at the PTO at 540rpm due to the gearing...

Guys - I've fitted a post hole auger to my BX25D but am concerned about the amount of wobble in the PTO shaft? Do you think it's okay or is the shaft bent or something else amiss - it doesn't seem right to me, but this is the first time I've used the 3PL...

I just bought a 1996 Agco White 6124. Was looking at the PTO setup and supposedly the way it works is if you want the 1000 rpm PTO you install the 21 spline shaft. If you want 540 rpm, you install the 6 spline shaft. Problem is, I can't find a 6 spline shaft with the machine. It's already got...

I have a used Bolens 1308 PTO that I would like to sell. New bearings, new belts and new unused rubber coupling. Also includes the lever and cable to operate it. Would like $250. Shipping would be extra. Phone 360-520-3808, call or text.

I have had intermittent PTO engagement. I see the valve body on right hand side that has two solenoids. One on the front side and one to the back. I checked for 12v on the back connector and didn’t have any with switch on or off. All wires (as far as I could see) looked in tacked. - is the...

I’m looking at buying this PTO chipper but can’t find any info. Owner doesn’t know brand/model. Anybody recognize the brand?

The chipper flywheel was stopping and the engine wasn't bogging down... I discovered that the secondary pulley driving the flywheel was spinning on the shaft. I assumed that the shaft key either fell out or disintegrated based on the metallic dust on the inside of the pulley. Looking at the...

Just bought (due in November :( ) a new ck2610 (woot). I will use a snow blower, but haven't decided front or rear, yet, and since i won't take delivery until winter, I probably won't be able to make up my mind this year. Rear leaves the bucket (helpful) but requires taking off the backhoe...

This was the first weekend that I have really used the PTO - couple hours and I was mowing. I stopped for a little bit and then started it up again at which it wouldn't do anything even though the dash light was on. I opened the fuse box and found the 5 amp blown for the PTO. I put another in...

Hi, My JD setup is making a racket... some due to loose sprocket/chain - replaced the sprocket and chain/tightened... Some of the noise might still be that I was not paying attention to aligning yokes.... got that from another thread.... but I've also found the PTO shaft is rubbing on the tie...

Basically the title - Why do all PTO drive shafts have grooves? The groove radius varies a little, from 6.7mm to 8.3mm (6.8mm to 8.4mm according to the book I am reading).

I’m trying to figure out what’s wrong with my pto it’s a John Deere 4105 and pto will engage and disengage as is supposed to but doesn’t have enough power to turn a brush hog and if I hook it up to a auger it spins it but as soon as I put pressure down it will stop moving

Jd 4500::while using bushhog when I get in thick grass such as the road grass I call it, pto stops...shaft and all.. the manual says not enough rpm on tractor..give more rpm..what do y’all think?

We have a 1982 Zetor 5211 with something broken in the PTO system. The PTO engagement level in the cab seems to no longer be connected to anything. We pulled the seat and transmission cover off but there is nothing obvious and we are not sure where to go from there. Does anyone have a PTO...

Good afternoon. Im considering importing a RG24 pto driven stump grinder from China. Has anyone got one? Are they any good? The only one’s available in Australia of this type are made in China anyway.

Hi everyone. I purchased an Agrimetal BW 1600 (PTO blower) for my BX2380 a few weeks ago. Everything looks great but I'm having trouble with cutting the shaft. I measured it up and found I need to take about 5.5" off. Of course, I need to take that off both metal shafts and both plastic...

Hey guys. Just wanted to share my channel with you. I work as a Turf Mechanic for many years and I'm still learning everyday but I may have some videos to help some people with certain issues on a variety of machines. I also work on Kubota / Case and New Hollands as well. Please subscribe to the...

Hi I bought a older JD 850 2 wheel drive and I have a question regarding the PTO. Is it normal while tilling or bush hogging to hear a click noise when you engage the clutch while using the attachment? is it some sort of slip clutch built into the tractor. it is a fast click not a grind or a...

I just bought a used John Deere 850, 1981 model year. It has a transmission PTO. Does anyone know if the PTO on this tractor can be converted to some sort of continuous/independent PTO ?