kubota bx1500

The dash, well, sucks. Left side icons and colors under lamps have all cooked off, and the sticky tape seems to have darkened and lightened areas - in tape outline. (Even HST and it's peers cooked off.) So, are we spending the 3 bills for new silver paint to cook off anyway, or DIYing a...

As above, these have a metal, odd shaped thing that says Kubota BX and is ribbed. Others do not. What is it, which section of part book?

I have an opportunity buy for a BX1500 for $1,400. I wasn't really looking for a tractor, but have about 3 acres of property and having one would be really handy. I feel like this is a pretty good price, assuming it runs well. It has a LA181 loader on the front and a mower deck I won't really...

570 hrs, runs fine, just that temp guage needle never moves more than about 1/8" up from cold even when run hard. Needle does fall back when ignition is turned off, so that part works. Where should the temp be? Thinking about changing thermostat.

This first started a couple of weeks ago while cutting the lawn for the last time this season. The engine would randomly die for half a second or so then resume. It did this maybe 4 times in the last 30 minutes of work. It only did it while the lawnmower was operating, so I figure it must be...

I can't find the thread but some months ago I asked for help in being able to lower my mower to mow while still have a 32" tiller attached at the rear. The anser is you CAN in a sense use the mid mower with a tiller attached by judicious use of the top lock knob for the hydraujlic lift. You you...

To get an accurate reading do you want to thread the dipstick all the way into the axle or just poke it in? (There is a big difference in the two readings) Thank you

So I have a new Hamney 32" tiller (toolots.com) mounted and my normal center mower is still there. I tilled the small garden fine with the mower set up high. Worked fine; I could lower the tiller yet the mower was still high enough not to drag. But I know when I go to use just the mower alone...

Good Day everyone, I recently purchased my first Kubota BX1500 tractor,(see pictures. I am looking for some used or aftermarket accessories, specifically a front end loader. I believe the FEL for the BX1500 is the LA181. Any suggestions for places to search for used or aftermarket parts would be...

I have a Kubota BX1500. It has a lift pump and two inline plastic fuel filters. What happens if water gets in the system? Thank you

I have a 2006 BX1500 Kubota. Recently my Lubrication oil level has been getting higher as I use the tractor. I seem to be getting Diesel fuel in my oil from the Fuel Injection Pump. I have ordered a pump seal kit and plan on installing the kit in the pump when I get it. I would like to have...

I have owned a BX1500 for a few years here in Alaska. During the winter I warm the engine with a torpedo heater for about 30 minutes before start and this usually results in the engine starting like it would on a summer day. This year however it is colder than usual, already well below zero...

My BX1500 leaks HST fluid slowly. Is there a UV dye that is compatible with Kubotas HST fluid? Thank you

Around 20 years ago I bought a Kubota BX1500 with an end loader. I use it mostly for driveway maintenance. It's served me well but yesterday I noticed a puddle of what I think is 90w gear oil around the right wheel. Have any of you other BX1500 owners ever had yours spring a leak there? If so...

I have a 2005 BX1500 and would like to put a quick hitch (BX2711) and front blade (TG2754) on it. It has never had a front loader and I have no Joystick or hydraulics for this so not sure where I can get what I need. Also not sure exactly what I need or if there is any manuals on how to...

Does anybody have a concise list of differences between these two tractor models? I've searched and haven't been able to determine what's different. Thoughts?

Hi, I'd like to keep the BX1500 mid mower and a small rear 3pt scoop mounted at the same time, but I need to somehow keep the scoop from going too low and hitting the ground when I lower the mower. I've tried all the adjustments, and even made a shorter top support out of a 2x4, but nothing...

Found an 03 kubota BX1500 that a guy is selling by me. It’s in fair shape but is functional nonetheless. It has 1100 hrs on the meter which stopped working last year... so maybe 1500hrs?!? Has an FEL and a 54” belt mower which is a bit on the rough side. It will need a power steering seal kit...

Hi all, I have the above mentioned tractor that was given to my wife and I by my father-in-law and have run into an issue. It's got a loader, mower deck, and rear grass catcher. The hour indicator reads 136 hours but I think it's closer to 400 from what is checked off in the owners manual. My...

I've had this tractor for 15 absolute trouble free years. Not one problem. Bought it new. I'm assuming my leak is some type of front axle seal leak....ASSuming. Looking for guidance, please. 1. Is this a front axle leak? 2. Is it a seal? 3. AND, a BIG 3....can I fix it myself? Normally I'd...

While changing from turf to bar tires for the winter, my buddy noticed the spacers between the rims and the hubs of my BX1500. He has a BX2300 of the same vintage (2004) and does not have these spacers. The front-end and wheels are the same on both models. Since getting the spacers lined up...

is it better to buy new or have it rebilt also how hard to remove .

Good news bad news. Good news: Daughter has a contract on a home. Bad news: small level lot so they don't need the BX1500 MMM and do need the money sooooo the BX1500 MMM with around 800 hours basement stored is going on Craigs list for $6500.:anyone: He has been so proud of this mighty mower...

I have been looking for a tractor for a while but started seriously looking daily and calling around. I found a bx1500 with 48" belly mower and la181 loader I assume is stock. The owner said he'd accept $6k cash since I'm from out of state and serious about buying. I'm tight on cash and really...

Has anybody replaced the low fuel warning light with a regular fuel gauge on a BX1500?

I have to remove all 4 wheels next week to have new tires put on. I really have no other option than to put the little thing up on jackstands. I have the Factory Service manual and they mention nothing about stand placement. There is one grainy photo that shows stands on the frame right in front...

I've had a Kioti CS2410 in the past, loved it but got rid of it in favor of a zero turn and using bigger tractors we have here at the farm. Now that the tractor is gone, I find there are tons of things I did with that small tractor I cant do with the zero or a bigger tractor or skid steer...

BX 1500 started blowing black smoke lost power I shut it off I have not been able to start it again. I have replaced both fuel filters the air filter both glow plugs and drain the tank nd put fresh diesel in it. still won't start, cranks fantastic, just does not even try to start

Hi all, I have a 2004 BX1500 that randomly will not start. It will crank over with lots of speed (has a new battery) but when it decides not to start, its like its not getting fuel. One thing I have noticed is normally I hear a loud solenoid clunk when I turn off the key. But when it wont...

Hello all. After I spread 50 tons of gravel this winter, I will pretty much only be using the tractor as a lawn mower. So I figure its time to sell it next spring and just buy a riding mower. I have seen this year and model of tractor listed anywhere from 3k to 10k on various tractor...

Hello people ! I'm hoping to pick someone's brain with this one. My 2006 Bx1500 power steering has been irritating me since I bought it in 2009 at 240 hours. Today has about 775 hours on it . Absolutely no difference in the steering since then but I had put a steering ball on the wheel at 7...

Hi all, I saw an add on local craigslist for a couple old Kubota grass catchers. Is reasonably doable to adapt this model to my BX1500 and RCK48 deck? I'm thinking 3 PT mounted and rear PTO driven blower, then have to figure out the tubes and deck boot. Used Kubota equipment is not common...

Hi all! I finally bought a tractor! Just want some feedback. You know, re-assure me I bought a good tractor for a reasonable price. :)) Two weekends ago I saw it sitting in the back of the dealers lot with the trade-in tag on it. I got excited because I rarely see a used BX for sale even at...

A month or so ago I picked up a nice BX1500 Kubota with 520 or so hours on it from a reputable local dealer. I've mowed with it three or four times since then and all has been well. Lately I've noticed about a 1/4 tsp.-sized oil leak on the garage floor underneath the back half of it when I...

Hi, Does anyone know if the seals on the LA181 FEL hydraulic arm cylinder can be rebuilt or must the cylinder be replaced? The rod seal is leaking a small amount and like most oil leaks quickly creates a huge mess. Thanks, Robert

Decided to up my search to smaller used tractors for mowing. I am going tonight to look at a 2005 Kubota BX1500 with 54" MMM for $5k at a local dealer. Does this seem like a decent price for a unit with 520ish hours? Kubota dealer nearby offered me $700 in trade for the JD L130 I just put the...

Has anyone mounted a Sims cab on their BX1500 ? My question is , how do you seal off the shift levers to keep the cold out ? any suggestions ?

Thanks again to everyone for you support in my other thread about buying a used BX1500. i pretty comfortable with what to look for and hopefully i'll be able to get a look at it this weekend. One thing driving this purchase it being able to run a 50" front mount snowblower with it, i found a...

My yard has a slope (measured at 13 degrees and covering about 1 acre) that I mow by traveling up and down with a zero turn mower. The mower is a 52" cut with 23 hp. The major problem I am encountering is a lack of power while mowing uphill. The mower is in good mechanical condition and...

I was recently able to pick up a bx1500 while cleaning out an estate. It has been under tarps for at least 6 years. I charged up the battery and got the dashboard to light up a bit. The fuel pump buzzes and the solenoid clicks after I shut off the key, but no indication of wanting to turn over...

I have a BX1500 circa 2005 with a bit over 400 hrs on it. Last year it began a slight hesitation that seemed to occur during direction change while mowing. I tried adjusting the safety switch on the seat and that seemed to eliminate the problem. However, it appears to be getting worse. I'll...

After servicing the BX1500 Monday afternoon I put the 48" MMM back underneath her for the first time this year. All I can say is I hadn't realized how much I missed her. I've been mowing this summer with our Cub Cadet 2146 which I resurrected in the beginning the season. Don't get me wrong...

This BX1500 is about 12 years old. Set the brake the other day and now it is frozen on. Pedal moves freely and lock lever operates normally locking and unlocking the pedal. Any one with knowledge of this system, suggestions or similar problem? Thanks for the help!

Good evening. I have an opportunity to upgrade from my current 2005 BX1500 with just over 500 hours to a 2008 BX1850 with just under 500 hours. 48" to 54" MMM. FEL on both. Possible difference in cost of $1500 to $2000 based on what i see 1500 w/FEL going for. 1850 is on my dealer lot, but...

Hi guys, I have an older RK48-15BX 48" MMM on a BX1500. I now also have a BX2230 which has a few inches longer wheelbase. The rear mower mounts seem to line up fine, but the front link from the BX1500 is about 4" too short to be able to connect. The Messicks parts diagram only lists one front...

Ladies And Gentlemen; I have a BX1500 w/FEL. I have a dirt moving project that involves leveling an area to accommodate a parking space. (Company truck) My question is, is my FEL strong enough to put a bolt on tooth bar to remove the clay base turf and possible tree roots. I am aware of...

New member...and I hope I'm posting this in the correct forum. I'm replacing the starter on my 2003 BX1500. I "engineered" my way through removing the old starter (took it apart in place because I couldn't get it out in one piece). I'm at a loss as to how to get the new starter installed. I've...

I just picked up a new in the box BX2711 quick hitch for my BX1500 from my local dealer. It was old stock and although I don't currently have a snow plow or snowblower for it yet, I couldn't pass it up for $200 cash complete with everything. If I remember correctly they were priced at $600 new.

I'm seriously considering trading my 2005 BX1500, 1200 hrs, with 48" mmm and LA181 FEL for a new BX25D TLB with 60" mmm, mechanical thumb, 12" bucket, 3 ph kit, std ROPS mount lights, block heater, and loaded rear tires. The BX1500 is in good condition, and everything has always been stored...

Good Morning; This may be an off the wall question, but I own a BX1500 and work on a B3200 (new, 90 year old father-in-law). Both have Front mount snow throwers, and both lower one side to the ground before the other. Is this normal? I say this is strange because this is my 3rd winter with...

Good morning. I am new to this forum. I have a BX1500 that i would like a wiring diagram for. Can't find them anywhere except in service manual and priced over $100.00. All help greatly appreciated

Hello...new to the forum. I have been trying to decide on getting a small tractor to mow with and do some light loader work. We have 2acres that I finish mow and a pasture that I mow down 3 to 4 times per year. We also have 2 horses. I have been taking care of everything with a Lawn Tractor and...

So after recently getting rid of my BX22, I have been looking around for a decent deal on just a tractor with a FEL and MMM if included but not obligatory. I have some retaining walls to dig for and build in addition to some lighter landscaping so pulling a small 4 box blade is also in the...

So i went to my dealer yesterday to get some parts for my tractor. one was the fuel shut off solenoid and the other was that silver band that Kubota has to hold down the air filter housing. surprisingly they actually had the solenoid. 2 to be exact. then i told them that the band. they looked up...

So we just bought 5 acres (used to be on a 60'x120' lot) and so I got a BX1500 w/60" MMM & 50" snow blower. This thing runs great, cuts great, although I'm getting older and the 60" MMM is a bit heavy to maneuver out from Under the bx1500. Further, I'm reading in this forum that the bx1500...

My grandchild managed drop a marble into my fuel tank. I can't see it because the tank is full, maybe when empty I can get it out. Until then, is there a screen or something to keep it from getting somewhere it can do damage. Or could the marble act like a ball valve and stop up a pipe? I...

Hi, I want to get a bushog for mowing after the summer rains. Anyone know the maximum size I can use on my mini tractor? Thank you, W:cool:

As it states, 330 hours on my BX1500 and it needs a new radiator. Had a screw fall into the radiator and it ran around and put a hole in the radiator. Bad luck I guess. Going to check to see if it can be re-cored, but is there an online source for radiators? Thanks in advance.

Can anyone tell me the fitting size for the hydraulic fitting that come off of the valve section of the tractor to feed the loader controls. I am buying a loader off of a tractor to retro fit onto my tractor, and want to be able to plug the hole when I take it of the 2006 Bx1500

I'm replacing a blown head gasket on my BX1500. Can anyone tell me where I can find torque specs for the head bolts?

I own a BX1500. I bought it years ago with an end loader, a drag blade and the small belly mower. I used the belly mower a few times and decided that it wasn't for me. It deprived me of the opportunity to get a little "lawn aerobics" using the push mower. So now the mower deck, with less than 20...

Hi Gang, I have a BX1500 with a 54 inch mower deck. Question is, how much grease does one need to put into the blade spindles? Most things I grease until some squirts out, but with the blade spindle how does one tell its had enough? Thanks, Robert

I'm a relative noobie here and have a 2002 BX1500..........with an LA181 loader and 48" MMM. I use the loader about every week on my property in the summer, and mow the lawn about once a week too. The loader is a PITA to put on and off so I just leave it on, but the tractor is fairly top...

Hi Everyone, How hard is it to replace the ignition switch on my Kubota BX1500? When I try to start it up, the key switch will snap back to the off position, if I don't hold it to the on position for a few seconds. I think I'm running on borrowed time, so I'd like to replace the switch. I...

Hello Curious on price to ask for my 2004 BX1500 188 hours 48 inch deck 48 inch rear blade 15 horsepower 2 cylinder diesel 4 wheel drive power steering rear pto three point hitch bar tires Always garaged, power washed 1 time, cleaned by hand all other times, all services performed at or...

The engine will run all day without a miss, but when i put in gear and use bucket, misses and kills motor sometimes. any one have a idea whats wrong, Thank You.

Can current or former bx1500 owners give me a price check on this bx1500 unit. I think it is on the high side buy it has low hours. I know with fel and 54 inch deck they where around 10k new. I think 6500 would be a better price http://m.reeseusedequipment.com/List/Tractor/ForSale/7320505/

Hi, Does anyone have tips on aligning the bucket on a BX1500? The bucket is higher by a couple inches on the right vs the left and it makes plowing snow a pain. Is the proper way to loosen the mounting brackets at the frame and then align and retighten? Thanks, Robert

I tried using the Search function with no success before asking here so please forgive me if this topic has been discussed and already answered. The last few times I've used my BX1500 (2004 model, 260 HRS) to clear snow the engine has died and if I can get it restarted it sputters for a few...

I have a 2004 BX1500 that I want to sell to a friend, so I want to price it fairly. From web searches, similar BX1500s sem to be prices at about $5000. That seems high and I don't know what they actually sell for. Any advice would be appeciated. 200 hours, 48" mid mount deck, well maintained...

I was about half way through mowing and I heard a noise a sound and felt a vibration. I stopped and did a once over and found a spindle nut loose and the bearings were shot. I put in and order for bearings and seals so I guess it is time to do my first BX1500 repair. The tractor is a 2005 model...

Hello. The mower just stopped engaging the other day after I'd mowed a little over an acre. When I lower the blade and engage the mower it shuts down the tractor engine completely. I've checked the belts and cleaned the mower and everything seems fine. Anyone know why this is happening and what...

After initially posting this, I see that the question has been handily addressed. "I suppose I could figure this out; but if there are particulars one ought to know about, perhaps they will be forthcoming. Where is the best place to start, in removing the deck? I see a number of...

I'm going to sell my BX1500 to a friend and would like to arrive at a fair value. It's a 2004, 4WD hydro, turf tires less than 200 hours, 48" mid deck. Excellent condition and well maintained by me. A quick check on the web came back with asking prices in the $6-7k range. Is this realistic for...

Does anyone know how to prime a bx1500? I hadnt used it since last spring because of the severe drought and just replaced the battery but it wont get any fuel for it to crank, (i am assuming since it has been sitting for so long).

Been experiencing a coolant leak. I can see coolant dripping off the bottom of the water pump after I've used the tractor so I believe I need to replace the pump. Here's a pic of the pump. There's a hole on the top of the pump. What is it and do I plug it or go buy a new pump?

Hey Guys, I am new here, but have read a lot of postings and have acquired quite a bit of information. I have the following BX for sale. It is a great mower, but I want (don't really need) a B2320 - FEL - MMM. Kubota BX 1500 - 4 wheel drive - 54" mid mounted mower- Diesel- Excellent...

So, I finally started the teardown of my tractor so I can hopefully fix my HST. I think think the forward/reverse high pressure relief valves have become loose in their bores. Hopefully this is the problem. I'll report back soon.:thumbsup:

I've been having problems with my tranny; it chatters/disengages under heavy load going forward and reverse is basically useless. It also doesn't stop abruptly, like it used to, when I go from forward/reverse to stop. I finally got around to testing the charge and high pressure relief valves...

I own a BX1500 and up until this summer it has always been garage kept. I have now ran out of garage space so now the BX has to set outside covered with a tarp. Winter is a ways away but how do I keep the BX warm in the winter months so it is not so hard to start when I need it to shovel snow...

The wife was cutting the lawn on her BX1500 yesterday and is slowed considerably and stopped going in reverse. Sometimes it will barely go in reverse, sometimes will speed back up. No warning or signs of problems before. Ii was researching and I am going to remove the screen and clean it...

Help! I need a K5371-3203-0 universal joint for my Kubota BX1500, new or used. Thank you Dave 1-804-572-0711

Today I moved about 5 yards of crusher run and I noticed that my tractor "shudders"/slips(?) when I'm going to pick up material from the pile, and it also does it when I'm moving around on the pad that I'm making. I've never had this shuddering/slipping issue before. It's comparable to wheel...

I am going to look at a used BX1500 with about 250 hours on it this weekend. It has a 48" MMM and turf tires. No other attachments are with it. It looks almost new in the pictures and according to the seller it has only been used to mow his 3 acres. Since this will be my first tractor, I...

Leveled out the snow piles/banks with the BX1500. Had to try out playing with the tiller in the snow . Just couldn't resist the temptation.!;)

Hi Guys I've been toying with the idea of a 2750 front mount snowblower for my little BX-1500. The rear blade just isn't cuttin the mustard when we get 10 or more inches of snow here in southern Wisconsin. Does this little 15 HP workhorse have the guts to handle a 50" wide blower? The dealer...

Have been looking to purchase a trailer for a couple months and thought maybe someone here could help clear the fog. I have a Honda Ridgeline and a Kubota BX1500 (with loader, 10.5 ft length, 1600 pounds). What I have been mostly looking at are tandem axle, landscape type trailers. I know...

I'm going to get a plugger for pasture and lawn. I'd like to get a 5 ft for the pasture, but not sure my BX1500 will handle it for the lawn. It will weigh about 700 lbs loaded with water. Does anyone have any experience/opinions on this? The max 3 pt for the BX is listed at 1210 lbs....seems I...

They now have me wondering about rear ballast on the BX1500. I made a platform for my 3 pt hitch out of an old potato plow frame and some angle iron. I am going to bolt in pieces of 2x6 between the angle iron and also use it as a platform for a sprayer. I am going to use 80 lb bags of concrete...

Anyone have a PDF version of an operator's manual for a Kubota BX01500, 1830 or 2230? Just picked up a used unit, and previous owner could not find his manual. Thanks

Don't know exactly why, except there maybe should have been another tie on the fuel line, or let the slack lay somewhere else, but the HST fan on my new used BX1500 nicked the fuel line that runs past it. I got my parts manual disc from eBay today, but this good computer can't read that disc...

I have read about the Gator Blades and I wonder if they rob any of the power. I have a BX1500 and a 54" deck and it does good on the factory blades. Has anybody used them on the BX1500 with a 54" deck and if so what are your thoughts? Thanks

OK, I hate to ask this but I'm at a total loss. I have BX1500, bought it new 5 years ago. Didn't look for my paperwork but I guess it's a 2004/2005 model. Short story, I was plowing a path of 3 feet of snow in our yard down to about 1 foot with my back blade this past winter. We have a hill...

I recently ran my BX1500 and it had trouble going up the smallest hills. I thought that it had a clogged trans filter or strainer. I did a full service replacing engine oil/filter, air filter, both fuel filters, radiator flush/fill, trans filter, UDT and cleaned the strainer. The strainer had...

The BX25 has been working out great over the past year. I use it all the time for everything around my 12 acres, but I still have to mow the 3/4 acre lawn around the house by hand. With the R4 tires and hillside the 25 really chews up the grass. So I've been looking for a second, smaller, used...

I have the kubota tiller for it but i was wondering is a disk harrow would work better for turning up a bigger part of land 250'x250' or is this too much to ask of a small tractor? something like this http://www.northerntool.com/shop/tools/product_200054024_200054024 wold my tractor even pull...

I have a Kubota BX1500 and I was going through the maintenance and I could not find a grease fitting for the front axle pivot point. Does anybody know where it is? Is there even a grease fitting? I have looked and I cant find one.

I'm pondering a serious upgrade in lawn equipment and have found a nice looking BX1500D with 300 hrs. within driving distance. Priced at $5500. The math sound fair to me but admittedly I have not beeen looking for long. Not sure if the deck is 48 or 54 but doesn't much matter either way. My...

I just recently picked up a BX2750 which I plan to install on my BX1500. Not surprisingly, it came with the BX2751/2752 quick hitch and pto kit (from BX1800/2200). Fortunately I was able to find the correct hitch (BX2711 - thanks Derek!) but here's where my questions come. Would it make more...

I had been using the FEL to remove snow on my 200+ foot asphalt driveway. It worked, but when the FEL was in the float position I'd loose steering when pushing a a lot of snow. After seeing some of the other plows that had modified, I figured it was time to build one myself. I started with...

I just started having a problem with my BX1500 going up hills in 2wd - it seems like the transmission is "slipping" - it is worse up steep hills and not noticeable on gentle ones. Also, when engaged in 4wd, it seems to help, the front wheels seem to pull through. Any thoughts? Does the...

I recently bought a used bagger and 48" deck for my BX1500 for $1.000 and I must tell you the bagger works GREAT:D I'll admit, the three bags fill quickly but today I mowed my 3/4 acre lawn, which is chock full of trees, in one day versus the four weekends it my wife and I last year. I'm a...

Ever wonder what your shorter BX would look like with the larger tires found on the other BXs? I got pix, if you're interested.

Over the past month we have had a few hot days here in central Virginia. It occurred to me while working the 1500 on one of these days that in the 4 years I have owned this little tractor I have never seen the temperature gauge do more than budge slightly "off the pin". I checked under the...

I mowed with my BX1500 for the first time last night with the tranny in "fast" mode. The tractor has the FEL and wheel weights on it. I noticed a couple times that when I stopped in the middle of one of my hills and then restarted up the hill the tractor would bog down a bit. Also, at one...

I am looking to sell my BX1500 with less than 100 hrs on it. I moved and it is "believe it or not" too big for our yard. I have no idea of what they bring these days. My Kubota dealer said he could not give them away....make that an X Kubota dealer. If anyone has an idea I would appreciate...

I have a 2004 BX1500 and it is getting weak in high range, right now the pump just seems to wine in high gear and the tractor has a hard time getting going.. the fluid lever is fine.. Do i need to rebuild the pump or drive? I have changed the filter and oil not that long ago.

I'm looking into purchasing a BX1500 and my local dealer said they vibrate like **** and I should be wary of purchasing one. I will not be able to test drive it because it is far away. He said a lot of people had traded them in because of this problem. Is this a problem with the 1500s??

I need an opinion on what the following is worth; 1 bx1500 with turf and 200hrs 1 loader with ballast box 1 4ft. kubota tiller approx. price for whole unit in u.s. funds thanks ericher69 p.s. don't know year but older style hood

Does anyone know the part number for the belly mower wheels for my BX1500? Or perhaps a suitable replacement wheel?

I'm new to this forum and I've been researching buying an all purpose garden tractor to mow my 1/2 acre+ lawn and do miscellaneous chores around my property (2 1/4 acres). I was originally considering a Home Depot/Lowes beer can tractor but a friend of mine has convinced me that they are junk...

Hi Guys, I'm new to the forum. I have been reading quite a bit of the posts and wanted to see if I could get some help. I have been looking at a 2006 BX1500 with 340 hours, a 54 in. MMM and a brand new FEL (just installed). The tractor is in good condition and they are asking $8250 firm. I tried...

I am needing anti-sway stabilzer chains for my 3-point as it never had any when I bought it (used). I see I can get the chain type but I really like the looks of the stabilizer bar type with pins. This looks much easier when having to take off or put on anything. Maybe I am not looking in the...

I've owned this BX1500 since it was new and it has been a very reliable workhorse. It has lately developed a problem with the 3 point hitch that is annoying at best, but I am more concerned that it is an indication of a larger problem. When I am using the box blade or the subsoiler, I will...

New owner here with a Kubota BX1500. I am new to tractors and especially Kubota. This is what I picked up: 2003 Kubota BX1500 - 145hrs FEL - LA181 48: Mid mount mower Price: $6800 (they said it was always undercover) It seems to run fine, looks fine and everything works great from what I can...

Any thoughts on the value of a BX1500 with 43 hours and just the 48 mower deck? Tractor is a about 3 years old and in excellent condition. No loader or loader valve is included.

I have 430 hours on my BX1500 we bought new about 4 years ago. I notice with this cold weather it hesitates when I go to start it. In the summer it fires right up. In past winters it has fired right up as well. I forget what you call it when you turn the key to let the glow plugs warm up but...

Does anyone know what the max system pressure on the hydraulics is on the BX1500? I would like to adjust the relief valve a little bit, all depending on what pressure it is set at right now, and what the max system pressure is. I will put a pressure reading gauge into the control valve. Then...

Anyone used a PTO driven wood chipper on a BX1500? What brand and results?

Hello, I'm new to this forum and I'm looking to purchase a (probably used) 1500/1850/2350. Right now I'm looking at a few units, including a BX1500 with loader and 54" MM. I'm OK with the lower capacity of the loader (~ 400 lb) but would appreciate any feedback on how well the 54" MM works...

How many quarts of oil do you have to put back in the engine after draining it to change oil? I'M changing engine oil in my Bx 1500 for the first time and don't know how much it takes to refill it. Thanks for the info.

Glad I went with the 60'' Hyd lift and angle front blade over the 54'' Hyd lift with manual angle front blade. The 54 inch blade isn't wide enough cover both wheels especially when angled. As many times as I kept having to change the angle I would have been constantly climbing on and off...

Hi: I recently purchased a BX1500 with 150 hrs. I just mounted the 48"mmm and noted that the three point hitch control valve controls the position of the deck. Unfortunately, the three point hitch raises and lowers with the deck. My question is this: Is there any way to separate the...

I just got a kubota bx1500 from a buddy of mine. I am for the most part dumb when it comes to working on tractors I was told that the hydraulic fluid should be changed and he didnt know how to do that. I was wondering if anyone could tell me where the drain plug is and how much fluid it takes...

I'm looking for a mounted set of turf tires to fit my Kubota BX1500. Location is Woodstock, Va. near I-81. One dealer in Warrenton said they should go for about $100. He just didn't have any sitting around at this time. Thanks for your assistance on this.

I recently purchased a slightly used Kubota BX1500 with FEL181 and mmm54" deck. It came with tractor tires. I'm very happy with the set-up but I am going to need a set of turf tires to use this thing this spring. Part of my property is on a hillside that can stay very soft and moist. So I'm...

Hi: Im new to Tractorbynet and I just bought a BX1500 with 150 hours in excellent condition. It has a 54mmm and a manual angle 54" front blade (TG 2754) on a quick hitch. This front blade is controlled by a pedastal mounted 4 way valve. I think its called a BX1612 4-way valve. I am...

Ok, before all of you ROPS police start up, let me make the disclaimer that I am a big boy and responsible for my actions. Further more, above all, I use common sense when operating my machine, whether cutting the lawn, plowing snow, or using my BH or FEL. Started out the by upgrading the...

Now that I have the Kubota BX1500 and don't need the 2 Bolens 850 Tractors I'm trying to decide what to do with them. What would I do with them if I were you?

My 2 have impressed me at just how much tractor they are for such a small tractor.:cool:

Does anyone have experience with the kubota pto grass catcher for the bx1500? It's the $1500 3 bag system that hangs off the back and has the PTO turbine. I've got the 48" deck and I'm wondering if the grass catcher has enough vaccum to to pull leaves or debris without the blades turning. I...

Who all has a hydraulic lift and angle front blade on their BX1500 ?

Just bought a used 2005 BX 1500. Figured out how to use it OK except for one item. The control on the right which raises and lower the 3-point hitch and mower deck seems to lower or raise both at once. Is there any way to operate them seperately.

Just bought a BX 1500 from a neighbor who is moving. Anyway, want to give it a good service and change filters and oils. The Kubota is a good ways from me but the NAPA guy is just down the road. Anybody have the NAPA part numbers for the filters. The old ones on the tractor are painted gray and...

Although it was fun trying to abuse this little machine tonight, I have to say it is built well because it did not break. I tried out the front blade trying to move the brush pile, which the machine could not do. It was fun slamming into the pile wishing that something would budge - but it...

After some serious consideration I decided the little Kubota just recieved it's next strike. I figured if it couldn't really cut and bag the grass then it was strike one. But after dreaming about it all day, I realized that since it was sized for a grade school aged operator, and couldn't cut as...

Hi everyone. Been reading all the good forum advice for quite some time. Well it is time to replace the old tractor. I've been leaning towards getting a little Kubota from all of the good reviews you guys are giving them. Well I was 'lucky' enough to rent a little BX1500 with a few attachments...

Anyone with a BX1500 and a rear mount snow blower, what size are you running? I am looking at a 50" snow blower, is that too big for a 15 horse tractor? I don't want to over do it, 46" seems to be the next size down but I am getting a good price on the 50" model. Any input would be...

Guys, I have about 90 hrs on my '05 BX1500 with 48" MMM and FEL with no problems at all. I keep it serviced very well and usually mow with some light FEL work. I have about 1 acre with 20% grade. Use 4wd a lot! I am wondering if any of you BX1500 owners have had any problems or concerns that...

All: Found these 2 machines at huffmans2. Inventory by make (scroll down to the "K's" to find the 2 BX's listed. Hours are low and the prices are decent. Pix are nice too.:D FWIW......... Swmpbgy1

Well I never thought it would happen to me, but I want a bigger tractor. :) I have a BX1500 with an LA181 FEL (with toothbar), and 54"MMM. I am located in South Central PA, and have just put it in the paper and craigslist for $10,000 obo. It only has 111hrs on it. I am trying to make the new...

Hello all. I am new here. I just bought a 2004 (new to me) BX1500 with a 48" MMM. I am having trouble raising and lowering the mowing deck. It seems to go up and down unevenly. In other words, the right side of the MMM (near the grass chute) raises higher and goes down lower than the left...

JD 455 $4700 used vs BX1500 NEW $5700. Which price is the best price ?

Which one would you buy?

Hello, I am seriously considering selling my BX1500 - just turned over 103 hours. Mobil 1 synthetic oil and always stored in the barn. Used mainly for the FEL and only mowed maybe 10 acres total since new. I bought new from Enlow Tractor East, in Tulsa, Oklahoma in early 2003 It has the...

In the past, I've done a ton of heavy equipment hauling using 'proper' trailers and tow vehicles... now I'm on my own. My tow vehicle is rated for 3500 lbs. and I've installed a Class II hitch. I'm looking at 5x8 steel tilt-bed utility trailers with single axles and no brakes. My question is...

Gents, I need to know if the quick hitch and drive shaft that came with a BX2750B blower for a new BX1500 will fit or can be adapted to my BX23. Thanks, Rusty

I'm selling my 2004 bx1500- it has 147 hrs on it.....its in "good" condition....all fluids have been changed regularly...bad parts- cracked headlight, small ding on hood, and signal lights missing lens...anyone have any idea whats its worth?????? Thanks...btw it has a loader and 48"mmm

Having problem with front axle housing leaking oil from pivot replaced o rings and backer washers but still leaks,it does not leak that much and only when in use would be thankful for any help on this problem. Jim

Looking for input on a tractor purchase. I would be using it to maintain a 5-acre lot. The lot is rectangular, flat and rough in spots (old farm field). First goal is to keep the area mowed, second is landscaping, etc. I have a 300 ft paved drive, and keep about 1/2 to 3/4 acre groomed like...

Has anyone had any experience (good, I hope) in using a 3pt tiller on a BX1500? I'm getting conflicting information from a number of dealers. I was thinking of a 48" from TSC possibly. Thanks in advance!

I've seen some listed for sale with 300 hours for not a whole lot less than I paid for it... I figure I'll put ~40-50 hours per year. At that rate, figuring I maintain it and don't abuse it, can I get 10 years out of it? 20?

My new BX1500 was delivered this past Friday :D . I finally got a chance today to take a few pictures of my new toy (I mean tool). So far I am very happy with the BX1500. My main use will be mowing but I also purchased the FEL for small jobs. I own a B3030 for more heavy duty loader work. I...

I am looking to purchase a BX1500 to replace my old one. My previous 1500 had a 54" deck and turf tires. My question for all you bx owners out there, 1) Is the 1500 better suited to drive the 48", or should I not notice the difference between 48" and 54", 2) does anyone pull a KK 3pt finish...

This has been driving me crazy all afternoon - and I have to 'vent...' I installed a Hella dual-beam work lamp on the rear-end of my my BX1500 today - twin 55w lamp style - and I'm quite happy. In fact, it's brighter than the front headlamps. Anyway, my issue is as follows: I was raised by...

I signed up for a brand new bx1500 a few weeks ago - the dealer is just waiting for the la181 loader to arrive from Kubota's warehouse. I did get to see the machine a couple of weeks ago - only 4/10 of an hour on the meter and no faded paint - so I assume it was assembled fairly recently. The...

I was just wondering if there are any NEW BX1500's left out there in dealer land? I am thinking about getting one as a second tractor for just mowing. Thanks, Norm

IMHO this is truly an excellent review. This gentleman is really somethin' else! Kubota Sub-Compact Tractor BX1500 Review at Epinions.com I'm doing some research for my next tractor and I just came across it so I thought I'd share. Feel free to chime in here if you'd like...

I just completed the deal to trade my bx1500 with mmm and fnl for a new 2350. Delivery is tomorrow AM. I've been very satisfied with the 1500 but thought a bit more power would better facilitate gravel drive upkeep with Woods 48 in box blade and offer the possibility for a few more...

I recently purchased the Kubota grass catcher and put it on with no problems except for the MMM chute. The dealer swears the chute is for my BX1500 which has the 54 in deck. But the contour of the chute doesn't even come close to matching my RCK54-15BX deck. When I took the chute back to...

I have been looking at a few remaining BX1500's. The ones remaining all have a 48"mmm. I have ask two dealers about the 54"mmm and both say it too big for the BX1500. Has anyone had any issues with a 54"mmm? I know it is an option from Kubota.

Hello to all: I am about to perform the 50 Hour service on my BX1500. Any caveats or issues that the "book" never talks about?? Things to look for or other unwritten discoveries from those of you far more experienced than I?? Thank you for your time. PKS10

Dear Forum: I am a complete beginner, so I apologize in advance for my lack of expertise. I am thinking about purchasing my first compact tractor. I am interested primarily in mowing and in tasks involving a front end loader (moving stones, mulch, etc.). My yard is about an acre, and I have...

Is anyone using thier BX1500 with a snowblower or rototiller? If so, what equipment are you using and how well does it perform? For that matter, what MM Mower sizes work with this little beast...seems like 48" would be about the limit. I'm thinking primarily about a rear-mounted 3-pt...

For my small 1/2 ac lot, I'm wondering if a BX1500 with a fel would give me enough capacity to bring back a few dozen yards of material like topsoil, 3/4" drain rock, etc... The lot is flag shaped and I'll be getting the material dumped by the road. I have a few hundred feet to take it where...

Yesterday I filled the rear tires on my BX1500. I used winter formula windshield washer fluid and did a rough calculation beforehand to figure out how much I needed. Well, my math must have been off because I figured I'd need about 5 gallons per tire and ended up having to go get some more...

I am looking to purchase a BX1500 and tiller. Are there other tillers that will work with this tractor other than the Kubota B40C? If so who are the manufacturers? Thanks!

Kubota BX1500 Hydraulic Blade & Catcher System Buy it now price of $1,800.00 located in Beltsville, Maryland. Looks like a good deal. web page

Since the BX1500 is being phased out I was considering tracking one down. I'm curious to see what everyone has been paying and what discounts/incentives Kubota has authorized so dealers can move their existing stock. So all you folks out there, what deal did you get? I've found one and I'm...

It's been about 3 months since I got my new toy, but until yesterday we didn't have a digital camera. So, I thought I would post some pics of my almost new Kubota. This first picture is after a hard days work yesterday spreading 16 yards of topsoil (1 tri-axle dump truck load) for my father in...

will a bx 1500 power a post hole digger? I see that Woods has a small unit available. Is the tractor tall enough to use it? Also, how does auger size affect digging effort? I would like to use a big auger, I think I saw a 9 inch diameter available for the smaller digger. Has anyone used a...

Hello, I have a question about the rear blade I just bought for my BX1500. Before I bought it, I asked the dealer if it could be turned around while mounted and he assured me it would. But I mounted it for the first time and it hits the lift arms when I try to spin it all the way around. It is...

I know this subject has been beaten to death. I used the search function and found a lot of references to other BX tractors, but not my answer. I am looking for filter brands other than Kubota as the local dealer charges $30 for both of those filters, combined. I know some of you have found...

Finally got around to welding on the bucket hooks for the LA181 FEL on my BX1500. The end hooks are 3/8" weld-on forged grab hooks (WLL 6600#). I welded them on a piece of 2"x4"x1/4" flat stock for added stregnth. I also did not weld them right to the edge, as this would prevent a chain from...

Has anyone out there installed or attempted to install the high capacity alternator kit (BX7310A) on a BX1500? My dealer has informed me that, even though it is listed as a BX1500 option on the Kubota website, the high capacity alternator kit is only for BX18xx, BX22xx, and BX2x. After looking...

BX1500 - Dang it! Now I\'m in Big Trouble! Broke. I made two stupid mistakes in a row and couple with the idiotic location of the transmission oil filter I'm in trouble. Mistake 1 - Neglected to take off the half shaft that connects to the transmission when I removed the deck about 3 weeks...

Hi, I was wondering if any BX1500 (or other BX series for that matter, though 1500 is preferred) could post the following measurements for me Front and rear tyre size Distance from loader upright to the front axle Loader pin Diameters Loader arm lengths (upright to bend, bend to bucket) Ram...

I recently purchased a new BX1500 and have used it now two times to mow. After searching for a similar post, I came up empty so here it is. Does anyone with a BX1500 find the fuel light to be hypersensitive? I was on the machine with a full tank for less than an hour when it started to blink...

I have been monitoring this board for a couple of years and I have decided to maybe make the plunge. There appears to be some deals now on the BX1500 since it is going end of life. The 0% for 36months and $500 rebate both are nice :-). I just saw a BX1500 with 54MMM on eBay for $6999 at a...

if they are going to scrap the bx1500 what will they put that little engine in? they just devoloped it right? i was planning on buying a 1500 just not this year. if i have to go up on price ill probably get a gc2300 massey.

Hello, newbie here so go easy on me. I'm strongly considering a BX1500 but looking for advice (or reassurance) that it will do what I want. I can get a BX1500 with 54" MMM and rear blade for about $7800 (price includes the $500 rebate). Toss in the 0% for 36 month deal and it is hard to walk...

Yesterday my BX1500 (99hrs now) cut out several times after running for about an hour cutting the lawn. It wasn't that it "missed" on one cylinder, the engine would just die for a fraction of a second then continue. I had just got some fuel from the local station before i started to cut the ...

I just finished the 50 hr service on my bx1500--no problems, thanks to good advice from this forum, however, when I checked the transmission fluid dip stick, it was dry--I put in the 2.7 gal without a drop spilling and there are no leaks. I've run the tractor and after running, there is fluid...

Is a BX1500 capable of pulling a 6x10 trailer loaded down with brush and small logs without damaging anything? The trailer is not too heavy and has a 3500# axle but is much beefier than your typical lumberyard special. I've pulled a small 4x6 with my BX1500 the 6x10 seems quite heavier.

Well, I couldn't stand it any longer. I went to see one of the local dealers on Tuesday and purchased a BX1500. He didn't have one on the lot so it's coming from their warehouse. I'm getting the loader, 54" deck, 48" box blade, mulch kit, and a toothbar. It's supposed to be in next week and...

I am in the market for a BX1500 with a LA181 FEL and a RCX48 mower. Any ideas on good baseline pricing and dealer recommendations. Thanks, Bob.

I was at a local dealer today and asked about the BX1500. He said that Kubota was discontinuing the 1500 and it would not be available next year. Has anyone else heard of this?

New Kubota BX 1500. $6200.oo

Is anyone aware of any aftermarket manufacturers that make a front blade for a BX1500, or have adapted any others? Kubota wants around $1400 for their front blade and it still has a manual angle. I just want it for pushing snow, I already have a loader on my LSeries tractor, but would like...

Just bought a new bx1500. My question is I have seen the new models with raised chrome badging(letters) my bx1500 badging is just a decal. Is this a 2005 or 2004 model? My dealer said that they had a problem in production with the chrome letters and changed back to the decal?

What do you think, I know I only have 10HP at the PTO, but I assume that I will just have to take it a bit slower. Any lift issues? Thanks

I have a bx1500 and would like to know if somebody could look at their upper radiator bracket. On mine there is an upper bracket on the left side with a rubber isolator but on the right side there is none? There is a spot for one. Wonder if there is supposed to be on the right side.

The deck on my bx1500 is cutting unlevel. The tires have the correct PSI and the blades are not bent. The left side of the deck is sitting almost 1/2 lower than the right. I looked in the owners manual but came away a little confused. Its sitting higher on the side that has the rod with the...

Got a chance to take some pictures so here goes

Just got the BX dropped off tonight. I only had time to mess with it for about 10 min. I must say what a nice tractor. I will give it more of a workout on sat. P.S. This is my first Kubota I have owned. I think we will be together for many years to come.

I just bought a 2003 BX1500 w/ 110 hours. Whats the smallest trailer I could safely haul it on??? I have no attachments other than the 54" mmm which as you know can be removed easily if needed. I would probably only use it to haul the bx a couple times a year so I don't need anything super...

How's this sound: BX1500 w/ Turf Tires, RCK-54BX Mower with 3-Blade Mulching Kit installed, BX2750A SnowBlower with required Hydraulics installed, Rear Wheel Weights, Engine Block Heater installed, Cruise Control Kit installed, and inclduing a 50-hour Service Kit - Sales-tax Free, Delivered...

As delivered. BX1500, 54" MMM and LA181 FEL.

I just looked at a BX1500D today. The dealer states that the tractor was delivered to him on Nov. 04. Looks clean. It has obviously faded some but still looks good. Nice waxing might clear some of that up. The plastics do not appear to have suffered much UV damage. The thing started right...

We are getting ready to trade in our 1985 Cub Cadet 1512 Diesel to hopefully a Kubota. Would like input from you on what size should we consider. Our Cub was great for last house, but now mowing more acreage and lots of hills and drumlins. We have a Ford 1710 4x4 with a brush mower and front...