ford-new holland 3930

I have the opportunity to purchase a 1994 Ford 3930 with a loader. I have brought the tractor home, and have been using it to do some bushhogging around my place. The tractor seems to run well, but need some cosmetics (a new seat and paint). The tractor is $6500 from a friend of mine. I'm...

Having watched a wonderful video on replacing the fuel injectors on a Ford tractor, see , I decided that would be my next project. Imagine my surprise when I went to swing out the battery box and realized the front-end-loader was in the way. If I take the battery out can I get to the injectors...

The right side cylinder on my Ford (New Holland) 3930 front end loader (Model 7309) has started leaking. Should I look for a re-build kit or just buy a new cylinder. Any video's on how to repair that? Thanks.

The owner's manual on my 1997 Ford 3930 (New Holland) shows a dual cylinder fuel filter. The filter on the tractor now is a single filter (SF 10082). Is one arrangement any better than the other? The dual filter has clear bowl that I assume traps water. Why wouldn't the single filter need...

I've had a early/mid-90's Ford 3930 for years, and never had any issues with the tractor...until several months back. Went through multiple episodes of sluggish acceleration/low power, ultimately figured out I had algae growing in the diesel (clogging the fuel petcock and injector pump inlet...

This is my first post here, so hopefully it will help. I recently bent the hydraulic fluid dipstick tube on our 1994 - 3930 - 2wd. In my discussions with the repair person we use for our equipment, he mentioned either......... a) Fabricating a new tube. b) running a small diameter die...

I am searching for a replacement wiring harness for a 1994 New Holland 3930. NH no longer sells them apparently. Does anyone have a source for one? If so please provide contact info. Thanks in advance, Jon.

I've run into an odd issue with a Ford 3930 3cyl. We've had the tractor close to 10 yrs, and never had an issue until a couple weeks ago. While bushhogging, it started choking down a bit...and acted like it was running on half throttle. I assumed the filter was clogged, so I pulled it..looked...

I recently picked up a Bush Hog 2400 QT front end loader assembly, and the plan is to mount it on a Ford 3930. The loader assembly came off a Deutz, so I will have to fabricate up the side mounts for the rear of the loader...shouldn't be too much of a problem. What I am not sure about is the...

I need to change the fuel filter on my 3930 but have never done it for fear that I may get air in the system and not be able to get it started back up. I have a few questions. What procedure should I follow to hopefully Change the filter without any problems? 1. Turn off the fuel supply 2...

My Ford 3930 calls for hydraulic oil In the power steering unit. It has regular Power steering fluid in it. Are they compatible, or do I need to flush the power steering fluid out before putting the correct oil in The Reservoir?

I’m new to the forum and new to owning a tractor. I’ll apologize ahead of time for any lack of knowledge. Started the tractor the other day and now it takes a tremendous amount of force to turn the steering wheel. Parked and noticed front-end leaking. This is a 1996 or 1997 NH/Ford 3930 with...

I have a Ford 3930 that will occasionally make a grinding noise in neutral with the clutch engaged (pedal out). It doesn't make this sound every time, maybe once every 5 times I lift the clutch pedal. It doesn't seem to make the sound when in gear or with the clutch disengaged (pedal depressed)...

Ran fine when parked about 5-6 months ago after Dad tilled his Garden. Visited property with him about 5 weeks ago (right before he passed), tried to start to no avail. Came back a week ago with more time to spend on cutting roads, I inherited a little problem looks like as I still couldn't...

Injector pump and injectors need to be replaced. Does the new components need to match the existing parts numbers? Or, can you just get a pump and injectors new for that model regardless of the numbers? Thanks.

Any recommendations to find replacement rear wheel rims for a New Holland 3930? Need a quantity of 2.

I just got the tractor in the title, and it's got a 7209 loader on it. I just replaced the 4 hoses coming off the control box as they were all leaking. I took care to change them one at a time and have added 5 gallons of utf so far, with no response from the loader and nothing on the dipstick...

I just got the tractor in the title, and it's got a 7209 loader on it. I just replaced the 4 hoses coming off the control box as they were all leaking. I took care to change them one at a time and have added 5 gallons of utf so far, with no response from the loader and nothing on the dipstick...

A few years back I had a Ford NH 3930 that I wanted to install a front loader, It was a Bush-Hog brand loader The loader I had come off a Ford 3910 or similar model, and the brackets would not fit the 3930. After calling all around, I finally got in touch with a man at German-Bliss who was able...

Hello again. My question is can i convert my current style leveling box which is almost froze up and change it to a style with crank handle. The only ones i can find say they fit a 3910 and not a 3930. I have had my leveling box apart and cleaned and re greased and thought it was free. But at...

Ok Guys Gals and anyone who has information that can help. I just purchased a new to me 1997 3930 with 7310 front end loader. The loader is plumed to the rear hydro outlets. I have a problem with this and a future upgrade so here is my questions. 1 the loader works up and down just fine. the...

My tractor is about a 96. It has the hydo selector valve under the seat. It switches from rear lift to the front end loader. It jumps out of position for the loader. I use bungee cord to hold it. Isnt there a plate or adapter that bolts on to allow both front and rear to work without switching...

Trying again here...I can稚 find a 3930 nose body panel or cowl. The fiberglass shell that sits at the front over the radiator. It痴 different from other similar Fords and can稚 find them in the aftermarket. Please help me get my burned tractor back in the game!

I have a 1994 Ford 3930 diesel with 4000 hrs. I was having some steering problems ( hard to turn, unresponsive at times). So I changed everything Hydraulic pump, Steering motor, rebuilt the cylinder. Now it is harder to turn, like there is no assist at all from the hydraulics. Any thoughts on...

Rebuilding a burned tractor for my brother. Striking out finding a new or used nose cone/cap/cowl. There are aftermarket ones available for 3910s etc but the 3930 and 4630 cowls were different. Any lead appreciated.

i'm having trouble removing the hydraulic pump on my 1995 ford 3930. the one behind the right foot rest. I've removed the mounting bolts but it seems like something else is holding it. lightly prying on it, I can see it move a little on the two dowel pins so it's not the gasket stuck. i'm...

My 1990's New Holland 3930 won't start. For background, this is a weird 3930 where a prior owner replaced the deisel engine with a gas engine. Anyway, it has a new battery and power is getting everywhere it is supposed to be. The distributor rotor is not turning when I crank on the ignition. I...

Well yesterday's effort with the 3930 was clipping several hundred feet of right of way and the 50' wide loop road around the house sight (something like 700' in diameter. All told about 3 hours of clipping with no problems. I shut it down to install an ammo can tool box and then went to restart...

My 3930 has a Quickie 310 loader hanging on the front. The source for the FEL hydraulics is a long hose from one of my rear remotes. I have the second 12 GPM hydraulic pump on the left rear of the engine. My ideal state is to have the two rear remotes available for equipment without having to...

Hello, How is everyone doing? It has been long since I posted here, you know, the hurricane happened and then in laws etc. We sent the New Holland 3930 to the local New Holland/Kubota dealer because we could not find a good independent dealer. The dealer of course wanted to put a new...

I was talking to this guy who works on and restores tractors and I mentioned to him that I have a new holland 3930. He asked me what year it was and I told him it was a 1999 model with about 800 hours on it. He immediately said that I better watch out and if I hear any strange knocks in the...

I was talking to this guy who works on and restores tractors and I mentioned to him that I have a new holland 3930. He asked me what year it was and I told him it was a 1999 model with about 800 hours on it. He immediately said that I better watch out and if I hear any strange knocks in the...

Not sure this photos will show up. They are photos of my old clutch and a new one I ordered. The new one part number is on the box. The old clutch had the inner tension springs or whatever you call them. They are same spline and diameter. The new one just didn't have the springs. Went ahead and...

In process of changing clutch-pressure plate. Found new pressure plate and clutch on EBay. Like to ask some of you mechanics if you replace pilot bearing and throwout bearing if they are still good? The original is Koyo made in Japan. I'm worried about putting in Chinese replacement bearing. New...

My trusted Ford 3930 4WD caught fire the other day...total loss. I am looking to replace it but used 4WD 3930s are a lot more than the 2WD. I am wondering if I can purchase a 2WD and bolt up my 4WD components which survived the fire (front axle, driveline etc). Both my old tractor and the...

The lights and hazards on my1999 New Holland 3930 ROPS are not working. Does anyone have the fuse box schematic and a lighting system wiring diagram? Of course the first and easiest step is check the lights for power, then fuse box then??? Not a grand time of year to start pulling sheet metal...

I don't seem to be able to close the latch on the top link of my tractor. The sleeve turns easily on the threaded rod but I think I should be able to close the latch down against the sleeve to lock it in place and I can't. I can move the latch from open to about half way closed but this is as...

We've got a Ford 3930 MFWA that seems to be leaking engine oil from the back of the oil pan. I figured it probably needs a new gasket. We just recently acquired this tractor about a year ago. It's got around ~600 hours but has spent most of it's life outside. Replacing the gasket seems...

Since the fall my 1992 (I believe) Ford 3930 has been having some starting issues. The starter seemed to getting a little noisy but it would still start. Occasionally I would turn the key and it wouldn't do a thing, not even click. A few taps on the starter with a hammer and it would go. It...

Okay all - Newbie here that has to relay instructions to another so mechanical work can be frustating. Here we go. My NH 3930 will not start. Wanted to check ignition relay first but my tool man cannot find relay. I checked diagram and thought it was in fuse box but he opened one small fuse box...

Hello, I need to replace the ALTERNATOR in my New Holland 3930 tractor. I have tried two brand new 950CCA Interstate batteries and both of them have lost cells, i.e. they are losing charging power I believe, after few weeks of use each. Luckily I replaced one under warranty. I was told the...

I have a Ford 3930 that is having the fuel solenoid issue. It is not getting enough power to allow the tractor to start. I ran a cable straight from the battery to the switch and it will start but at that point it will not go into gear. I am assuming that is some sort of safety mechanism that...

Tractor starts out fine, but as it warms up the power steering begins to fade and eventually quits. Changing the filter and flushing made no difference. Steering will work approx. 45 minutes before begins to fade. Any ideas to correct the problem??????

Have about 15a of old hay field that I would like to clean up and keep mowed to about 8" probably 2-3 times a year. All open area with no fences. I am currently looking for a new rotary cutter in the 8' to 10' range, to do the job. I currently have a Bush Hog 3008, 8 foot duel spindle...

Hi, I have a 1996 3930 (3 cylinder) that I've had for aroubd 4 years. I rebuilt the engine a year ago bc of excessive blow by. Last week, it died on me backing a trailer up a hill and wouldn't restart. I discover that the fuel tank was blocked with crud. Drained tank and out new fuel in, but it...

I'm trying to see if anyone know about or has a manual to the Ford 3930. The PTO when out and no longer runs. I can freely turn the shaft by hand. Turning on the PTO gives no revolutions at all. Loader works fine. Anything to check first? Is everything accessible through the rockshaft cover or...

I have a 1999 NH 3930. Having a problem with my power steering operating correctly. After warming up it pushes fluid out of pressure relief valve. About 3 months ago I replaced the filter and it improved for a short period of time. Now the leak is much worse plus fluid is frothy (getting hot?)...

I have a 92 Ford 3930 2wd with the manual speed transmission. I have a leak coming out of the bottom of the cover plate that the PTO shaft comes out of. I've removed the bolts and when I start to pull the cover off the shaft comes with it. I've read about how on some models a bearing will...

An 87 year old friend had a flasher issue with his 3930 tractor. I fixed it and in the process, I noticed the 25amp fuse for the thermostart was missing. I put a new in. Is there a dash light or some other way to see, if this is working without finding it under the hood? His fuel gauge does...

I have an early 90s Ford 3930 2wd. It has an Allied 394 loader with a 2 spool valve. I wanted to add a rear remote so I purchased a BLB BM70-3 valve and installed it on the tractor. After installation my loader arms would only go about as high as the top of the hood and the bucket would move...

The clutch on my 93 Ford 3930 is to the point where the pedal is almost all the way to the top before it engages. It doesn't seem like it's slipping but I haven't really tried pulling anything that would cause it to. What I have noticed is when I'm starting out in reverse high range it seems...

Can you swap out the fuel guage on a Ford 3930 without having to change out the entire instrument cluster? I'm finding plenty of clusters for sale on one but no single fuel guages. I checked the sending unit and at the current fuel level (about half a tank) I read 225 ohms resistance across...

Does anyone have any experience on what is involve in rebuilding the hydraulic selector valve on this tractor? I'm talking about the valve in front of the seat that switches the hydraulic from locked out (forward) to 3 point hitch (centre) to loader (rear). I think I'm having some issues with...

Does anyone know the inlet size I need for a muffler on the 3930? Thanks!

Hello everybody. Got a curve ball here. I am dealing with a New Holland manufactured by Clarke American-Lincoln model 510-010 year model 96. It has the LP setup. Does anybody Know where I can get ignition parts for it. Thought I found some and put them on order and lo&behold Wrong parts...

I have a 3930 with about 680 hours. I had a problem with mice chewing the wires to the instrument panel. I put the wires back together with splices and was able to get the tractor running again, although I still don't have it completely right as the gauges aren't working correctly. However, it...

I recently bought a 3930. Someone welded the telescoping lift arms in place. Is there somewhere to purchase these? Anywhere to find good used ones? Thanks, Craig

I am now on my third engine for my 1993 Ford 3930 45 HP Diesel Tractor. After 86 hours on the third engine my engine just blew some valves and a head gasket. Its pretty well finished. I have had to deal with a bunch of inequitable dealers. I leased this tractor for 9200 and have paid 6200...

I was over at a friends today that has a 1999 2WD Ford 3930 and he needs to replace the oil pan because he hit a stump. He was told the pan was $248 and the gasket is $40. My knowledge of Fords is very limited, but is the part he needs? If wrong can you point me in the correct direction...

I have a 1993 Ford 3930 with an Allied 394 FEL. According to the loader specs it should lift 1500 pounds. Mine seems to be maxed out at what I would say is about 1000 (6x6 round bale). It doesn't scream or whine, it just stops lifting. My loader is plumbed through the rear remove. Moving...

I have a 1993 Ford 3930 2wd that I've had for a little over a year. I love the tractor but it's super wide in the back because it looks like a previous owner put shorter wider wheels/tires on it. It's currently running 16.9x24 rear tires. I believe stock is 13.6x28. With the current set up...

I have a 1999 new holland 3930. My tractor has a one cartridge fuel/ water separator. It does not look like the picture that came with my owners manual that shows two cartridge set up with a fuel filter and sediment separator. I want to change the filter but am unsure about what to do...

I just changed the hydraulic filter on my 3930 for the first time since I bought it (used tractor) I probably lost a qt to half a gallon of fluid. I looked in the manual and can't find anywhere where it tells you where the refill is. I also can't find if there is a dipstick to check the fluid...

Hey guys, New to the sight and hoping for a little insight on my new to me tractor. Its a 94 Ford New Holland 3930 Highway tractor that I have bought from a local state lodge. It has been very well taken care off with service records present at sale and only 2003 hours. Anyways I bought it and...

There are 4 short hydraulic hoses in the joytick controller for my front end loader on my Ford 3930. One of them split. Can I find replacement hoses for inside the controller or will I have to buy a new controller? Where would you look for those kinds of parts? Thanks.

I have a Ford 3930 and the starter won't turn over. I replaced the battery. The old one was going dead but the new one is fully charged and the starter still won't turn over. The past weekend it would turn over and then other times it would just click when I turned the key. this was with the old...

I have a 1993 Ford 3930 with one of those high stack muffler that extends directly up. The problem is that when I try to mow around trees or go thru bushes and it hits a large branch the muffler unit gets bent. Prior to owning a Ford 3930 I owned a Ford 3000 and the muffler system went down by...

Hi Guys, New member, first post. I've used this site a lot when researching various things. I finally got around to signing up. I have a 1990s (93 I think) Ford 3930 with a manual transmission. It's been working great all winter. I last used it a few days ago and no problems at all...

Just got a replacement engine for my Ford 3930 and it is running fine. The problem is this was the first time I bushhoged with it today. When I started I could get it into gear and the clutch worked fine but after about 1 hour of use I would put the clutch down to floor and it would just stick...

Can anyone tell me if a 7108 loader can be mounted on a Ford 3930

Hey everybody, We bought a 94 3930 tractor in Oct. 2013 and it has been great for the most part. It has a Woods loader on the front of it and we are using the rear lift now to roll out hay for the cows with the hay unroller. Our issue is that the lift arms will not hold the hay unroller up...

I'm looking to add a 3rd function valve to my 3930 with 7310 loader for a grapple. Anyone install one. WR Long said they don't make a kit for it. Any ideas?

Our 3930 MFWD with 8x8 shuttle was acting a bit on the sticky/sloppy side. I adjusted the linkage so there wasn't as much play and lubed all of the moving linkage parts with Fluid Film. I can't believe I was too lazy to perform this simple task in the past, as opposed to just living with it...

Anyone know where I can get a Used Ford 7209 Front End Loader for a Ford 3930 2WD Diesel Tractor?

I have been looking at a used NEW HOLLAND 270TL Front End Loader for my 1993 Ford 3930 Tractor. Can anyone tell me if that will fit a Ford 3930

the 3930 has a rear remote, the loader runs off the remote. The remote valve is mounted on top of the transmission, just below the seat. Is anyone familiar with this tractor and can tell me how to run the loader without connecting to the remotes? I want to use the remote for the hydraulic top link.

I have not yet replaced the hydro filter yet on my 3930 (bought it used, previous owner had changed). Can someone tell me what is involved in doing this. Do you loose much fluid when changing? Is this fluid under pressure when tractor is cold? Do I need to add more fluid? I would assume the...

I'm thinking about a '93 model 3930, but it is 4 hours from me. It has the 8x8 trans and am wondering if the forward/reverse shift is synchronized. Is the 8x8 relatively trouble-free? I see that there is an optional high flow hydraulic system. Can that be verified externally? Looking on line...

I don't know if this should go in this section or in hydraulics, but would like to know what is involved in adding a hydraulic remote to a '93 model 3930. I'm handy with a wrench and if it can be a bolt on operation I can probably handle it. Approximate cost of parts and a source would be great...

Hi I am a farmer from Saskatchewan and recently purchased a 1992 Ford 3930 yard tractor. I look forward to others comments on this and other subjects regarding tractors

Default Ford 3930 is leaking out of the exhaust I just bought 1993 45 HP Ford 3930. It runs on Diesel. I paid about 5950. I had it delivered and am having another Dealer check it out. I just got a call from the dealer I brought it to and he is telling me there is oil leaking out of the...

I just bought 1993 45 HP Ford 3930. It runs on Diesel. I paid about 5950. I had it delivered and am having another Dealer check it out. I just got a call from the dealer I brought it to and he is telling me there is oil leaking out of the exhaust. This was after letting it run three hours...

I have a mid 90's ('95 I believe) Ford 3930, and I'm having an issue with the instrument cluster. Rats at some point got in behind the cluster, and have made a mess of the wiring. I've been able to get most of the wiring back together, but there are still a few wires that I haven't been able...

I have a mid 90's Ford 3930, and has developed a couple of issues. First is a problem with steering at lower RPMs, which I have narrowed down to a low/almost empty PS pump reservoir. Any particular fluid I need to run in the Ford for the power steering? Will universal tractor fluid be...

I have a 1995 Ford NH 3930 MFWD. The fuel shutoff solenoid is not closing when turning the ignition off. I've been having this issue for quite some time. On occasion it will shut off with the keyed ignition, however most times I shut it off manually at the pump. The solenoid wire remains hot...

I had to get a new battery for my 3930. Went to hook it up and I am not 100% sure I am doing it right. One cable has the battery terminal and another smaller cable bolted to it. The other cable has the battery terminal only. Is the cable that has the smaller terminal bolted to it the positive? I...

Hey everybody, We bought a 94 3930 Diesel Ford back in September or October of last year. I felt it needed a clutch but my dad didn't think so, but we went ahead and decided to split and see. It still had some life but since we had it this far, we decided to go ahead and replace it. I guess...

Hello, Long time stalker, first time poster. Hope someone can help me track down my 2 electrical issues. I have a 97 Ford 3930 that I picked up about 4 months ago. First, When the tractor is running, My fuel gauge works and my temperature gauge does not work when the lights off. Then when...

I'm looking at purchasing a 1999 new holland 3930 . Its a shuttle shift, 2wd, dual hydraulic, 55hp, 1100 hours shed kept with new tires, has front loader with hay spike(7310) what do you think is a fair price. Asking is $14000

My 1995 3930 is almost complete. Just need to install new wiring for and safety lights on rear. Here are some pics of before,during,after.

what type of hydraulic fluid is used in a 1994 Ford 3930 and where do you put it in

I just replaced the starter solenoid on my 3930. It was making a long ccccllliiickkk (Click) before engaging the starter. All wiring put back the same, now the tractor tries to start with the kill switch out and the key off, the the starter was on a continuous whirrr until I got the battery...

I am restoring a 1995 3930 with 8x8 shuttle tranny, that has dual hydro pumps and deluxe remotes. I have tractor disassembled to paint. Remote hydraulics where strong, but 3 point lift was very weak(full rpm's barely lifts weight). I should have tested rear housing mounted pump before teardown...

My husband needs a wiring diagram for his 1994 Ford 3930 can anyone help him? Thank you for your help

Hello i just purchased a 3930 and it is now blowing smoke and leaking oil. It looks to be leaking from a spot from between the front of the tractor where the oil pan is. Just below the belt. I am very new to tractors. This is my first one. Any help would be appreciated.

When bushhogging high grass the grass tends to wrap around where the PTO connects to the bushhog. Is there some type of shield or guard that could prevent this? Thanks in advance for your help.

Does any member have experience and advice on how to remove and replace rear PTO seal and Wear Collar on 1997 New Holland 3930?

Need help with headlights not working need wireing diagram

Just bought a Ford/New Holland 1996, 3930 diesel. Going through everything and find I cannot remove the outer air cleaner element. I have the wing nut removed and the retaining washer. There is a little tab on the end of the outer element which looks like an aid to help pull the elemen straight...

what type of fluid for transmission and power steering in a Ford 3930 tractor is needed?

I had a very clean little 3930 a few years back and replaced it with a larger tractor. It has since become evident to me that there is most certainly a need for both a large and a small tractor. I was considering trying to find another 3930 , but this time with FWA. I spoke with a local...

Hey I was wondering if I could get some advice on buying a tractor. I have been looking at a Ford New Holland 3930 with MFWD ROPS and canopy. It is supposed to be a 1998 model and it has around 2000 hours on it. I haven't went to look at it yet but I was searching for advice on whether it will...

I need some advice from the experts. I have a 99 New Holland 3930 4wd w/shuttle tranny. When tilling the garden with it, it runs too fast even in the lowest gear. I find myself wanting to ride the clutch in this situation, and I know that is an expensive mistake to make. My manual says that...

Reposted - quotes in the subject line don't work, and i couldn't figure out how to edit it...

I have a 1996 Ford 3930 that is rapidly leaking fluid out of the reservoir, it is not an external leak. Any ideas on what the problem may be?

Can anyone tell me the width from outside back tires of a New Holland 3930? Thank you

I removed my pto shaqft and pressed in new seal and bearings. now having trouble sliding shaft back in. stops about 4 inches of home. Any tricks to align it?

I need to replace the oil pan gasket on ford 3930 tractor, do I have to drop front axle? Help

Today when I checked the fluids all levels were OK. But, the transmission oil looked milky as if there is water in the oil. The rear end and hydraulic oil is fine. The engine oil is OK too. Coolant level is where it should be. Can anyone tell me how water can get into the trans oil or what makes...

I have a Ford 3930. I need to change the engine oil. I bought an ITT manual for information. It provides the quantities for fluids, but it does not state the correct type of oil that is required. Should it be Rotella 10W40 or something similar? I also need a filter, but assume that won't be a...

need to know what the timming should be on the 3930 and how to set it back properly? took it apart and forgot to mark it...:ashamed: thanks

I was at a local dealer yesterday to see the New Holland tractors and on the lot they had a 1993 Ford 3930 tractor, 4 wheel drive with syncro shift and a 195 loader. The tractor was purchased new, brought home, used lightly for 74 hours and then the owner past away. All these years it sat in a...

When I got my tractor, used, 4 years ago, there was an incorrect fuel cap basically just crammed into the filler tube. Fit not bad, for what it was, but was one of the first things I replaced with an OE fuel cap (exterior thread on fill tube). Noticed a little while ago that the OE...

The power steering on my 3930 seems slow when the motor is near idle. Is that typical or indicative of a potential problem? Can you tell me how to check the power steering fluid on a Ford 3930? Does it have a separate power steering fluid or does it use the same hydraulic fluid in the rest of...

I have a Ford 3930 with about 540 hours. I have been happy with it and have really used and enjoyed the FEL on it. It all seems to work well, but it has a very noticeable whine from the rear end or transmission. There seems to be noise whether it is in high or low range. In fact if I am on a...

Can the clutch be adjusted? Most rpms can't shift gears, just like no clutch. Y'day I tried to move clutch arm with adjustment on clutch rod back (toward driver seat) but i moved it too much and had no clutch. If you can adjust clutch which way do you move the rod or shaft coming out of the engine.

I am looking at a John Deere 430 round baler, wondering if my New Holland 3930 tractor will pull it efficiently. The tractor is listed at 45 PTO HP, so it might be a little small for that baler. Any ideas? Thanks

I have had rats eat my wiring to the cluster...this is the second time.... I sure need some help. I have seen someone post a picture of a 4610's wiring but have not been able to find a 3930's.... if you have or can take a picture of the back of your dash cluster, i would be very appreciative...

I finally acquired a tractor. After looking for far too long, I wound up buying from a family member a tractor which he had previously loaned to me. I put about 30 hours on it while it was here last year. I don't think he put more than a few hours on it since I used it and he decided he didn't...

What size disk will a NH 3930 handle on relatively steep rocky clay ground? Do you recommend 3 pt. or transport type? Thank you

Hey guys, Lately my loader slowed down and has made whining noises. And to be honest I have never changed a Hydraulic Oil Filter before I got my boss to do it but he wants me to do it as its maple syrup season and he is busy Can someone tell me how to change the filter? Does the loader hafto...

Hi all. I have a '92 3930 with 1350 hours. It has developed a problem that is getting worse and I'd like to ask you'all for a tip or two. The clutch works great and it's still strong, no slips, no erratic operation, etc. My trouble is this: When you push the clutch in to put the tractor into...

Looking at a '96 NH 3930. 355 hr. Good rubber, no loader, 2 wd. Seller said it is cherry, and pics make it look that way. Still 15 yr old tractor??? I like old iron though, and think it may be worth a look. Any one have any comments about the 3930? Anything specific I should look for...

i have a 1997 3930-headlights quit-have power at fuse and switch seems to be working-have power on side where power comes out for rear lights-dash lights are working-wiring is in loom so cannot see it but no lights on front=what do i need to look for

Does anyone know how to install a termostart switch on a New Holland 3930? This is the switch that preheats for cold weather starting

Hi Guys, Long time viewer first time "poster" I having trouble with my ford 3930 the transmission will work fine for the first 15 minutes of work without stopping for a break but after the 15 minutes are over the FRONT/NEUTRAL/REVERSE lever doesn't seem to work like you can put in gear but when...

I bought a used NH 3930. It is missing the drawbar but it has the drawbar hangar. I purchased a tandem axel landscape trailer that I want to hook up to the tractor and use to collect limbs/trees etc. to transport to a central burn pile. I have the following questions. 1. I found a swinging...

looking for 3-pt hitch for 3930 or left and right leveling arms to fit 3910. Thanks

well my nephew made my day today one of those I wish I had stayed in bed. To cut a long story short the pto engagement arm was just enough off the safety switch that it didn't start, no problem happens occasionally. My nephew was going to move the tractor and it wouldn't start me being on the...

How much flow (gpm) from hydraulic pump to operate implements.

Guys i need some help. I have a 1998 3930 with only 217 hours thats in as new condition. I love the tractor but i haul it around some and work in somewhat tighter spaces (in and arounds woods and trees) and was thinking a shorter wheelbase and 4x4 tractor might be the ticket. The 3930 rides...

Just bought a 1990 Ford 3930, 45 hp, 2wd, no FEL, with only 1400 hrs and new rubber all around. Everything seems to work well. Paid $5500. I feel like I got a good deal. Any thoughts.

I have a 1998 NH3930 w/192 engine with turbo and when it gets hot sometimes it must cool down somewhat before it will re-start. Also, when i turned the lights on one time while going down the road it died. I immediatly turned them off and it went right back running. Keep in mind this tractor...

My neighbor is offering me a 1997 Ford 3930 with 250 hours on it for around 14K. The machine seems well maintained. It has Ford's FEL with a hay fork. The engine has a turbo on it. (Why would I need that?) The price seems about right but I wanted to see if there were any known major service...

I have a 1998 NH 3930 with 160 hours. The serial number tag under the hood shows a 3.2L turbo engine with 60 gross hp. Can anyone tell me about this engine? i would like to know the PTO hp and were can i find further information. There seems to be very little info on these engines and even...

The front emblem on my NH 3930 has broken off two times. The emblem is a plastic oval that inserts into the top front hood. I guess vibration breaks the emblem studs. I know I don't need it but I am kind of particular when it comes to my equipment. Do any of you know where I can get an oval...

Two questions: 1. Just bought 3930 4x4 tractor and reviewing operator's manual concerning tractor I see two versions of 3930 tractor- 3930 AP and a 3930 N. Does anyone know what's the difference between the two? Contacted New Holland tech support and they did not know. 2. When this tractor was...

I was clipping pasture with a six foot rotary cutter and noticed the transmission building intence heat in fact there was smoke coming from the area. The grass was tall with areas of thick Johnson Grass however I was mowing in second gear. I stopped and let the tractor cool until the following...

I am looking at a 3930 among other tractors. I do not have a lot of experience picking out used tractors. The independent PTO clutch was just changed out and tractor has 1700hrs on it. Tractor appears in pretty good shape; doesn't smoke tires "ok". I did see a some oil aft of the the oil pan...

I'm looking at a Ford 3930 here locally. I've been looking for a 50 hp tractor for a while now and this one seems good. It is 2wd and has turf tires. I'll have to put R1's on it so that's a down side, it doesn't have a remote either which is another down side. On the up side it looks good...

I have located a refurbished Ford 3930 4wd with a FEL. I believe he said it was a 96 model, can't remember. Asking price of $13,500. Is that about average? Thanks for any help.

I own a NH 3930 (tractor no. 042423B, ModelCA51WX, engine C636596 -96 or 97 model) that is equipped with an oil bath air cleaner instead of the more common dry type. I need the bottom bowl assembly with the sealing ring. The catches on the bowl that I have are broken. The NH dealer said that he...

does anyone have any info on replacing the oil seal on the brake rod @ the rear axle housing. any info would info would be helpful. ps:i also posted this on the parts/repair board

does anyone have any info on replacing the oil seal on the brake rod @ the rear axle housing. any info would info would be helpful

I saw an ad for a 1998 Ford New Holland 3930 tractor with: MFD cab heat 7310 New Holland Loader 16.9/30 rears 11.2/24 front 1,175 hours Like New Condition I have not yet had a chance to go up and have a look at, and try this tractor. However, what should I expect to pay for something like...

Can anyone tell me where I might purchase an operators manual for a New Holland 3930 4 WD? It is grey market imported from Europe. Thanks

I am looking at a 1998 NH 3930, 2wd, shuddle shift, 98 hrs., 1 or 2 hydraulic remotes can't remember for sure how many it has. I would like to know about how much I should pay for this tractor. Thanks for you help