Search results

Would anyone know what hydraulic pump Blackhawk used for the FEL Attachment installed onto these Tractors? Mine has DX22X01 stamped on the side, but no manufacturer’s name.

Hi, having just a pump driven on front crankshaft for the FEL & Attachments, I was wondering how many have taken the time to add a Filter to the return to keep oil clean. Also thinking about adding a Hyd Oil Cooler to the return as well, I measured the temp on oil when using a motorized...

Does any one know the bolt circle diameter for the rear wheels of these tractors, and the pilot diameter? I think it is 4.75" x 6 Stud, pilot diameter not sure? I want to make an adapter to fit ford 8 stud rims fit on it, or at least try,, tks

A long axle , Wheels from a Festiva, a trailer coupling and a three point hitch, all used to move a shed across the yard to make room for a shop build. I was a little too early in the year, the wheel alongside the fence sunk in the mud, had to wait a week, then all went smooth. Dropbox - Shop...

Converted the PTO drive to a Hydraulic Drive for the cement mixer. Thought I would show it for anyone interested. Dropbox - Gerotor Mixer Drive.MOV

I have read Sodo's post on MillerMatic 200, because I was at the Tool Store today and looked through the welders. I am trying to justify the $1700 CDN on a Multimatic 215, or the Miller Matic 200 @ $1500.00 CDN I grabbed a brochure and it calls the MultiMatic 215 "new". I would like to be able...

Like probably most MIG Power sources, I am wondering how the user chooses the welding amperage? I see a single control on the CP302 Miller for voltage control, I have a Miller Xtreme 12VS wire feeder, which has a control for wire speed, but I don't understand how you choose the amperage? ( if...

The more I think of electric power bills the more I want to look at solar install? Anyone out there know where you could purchase panels, lets say bulk, unframed, where you could utilize to build your own array? I realize there is lots more to it than just the panels, but after my last months...

Has anyone converted a mower deck to cut brush? I was talking to a friend who has trails at his Yukon Fishing/Guiding Camp, and we were wondering if you could take an old KRM48 and attach flail cutters to the arbors? That way it would stand half a chance of living while cleaning up the existing...

Any one checked, shimmed the relief vale of the 3 point hydraulic pressure, and where is it located? Thank you,

Hi , just wondering if any one has tried to purchase the 2" Ujoints/Yoke assy to make their own pump drive shaft? The smallest swing from spicer, etc is 2.5 which makes it real close to the bottom tank of the radiator. I think the machine shop called it series 1000. Any one? , I posted in repair...

Hi , I would like to replace the front pto shaft driving my hyd pump for a FEL. The swing is 2 inches or 2" across the u-joints. If I could find two sets of yokes with u-joints I could manufacture myself boring or making the yokes fit 9/16" pump shaft and front crank stub shaft. The smallest...

I got some Cat MTO Oil, but not sure about it. What do you guys think?

Received my friction material today and got to work getting the disc repaired. Cost me $35.00 all in, not bad. Thought I would share what I did with everyone.

I have 963 hours and doing the clutch right now (stuck). third speed gears in trans are crunched. Other than that a nice little tractor.

Hi , I went to a garage sale this morning and ended up bringing home this Kubota KRM48. It has new belts and a set of new blades with it. Is there any tips or tricks that I can learn from anyone out there before I use it?

Split tractor because the clutch stayed engaged. Does any one have a service manual pic of how this throw out yoke is attached to the shaft. Is the yoke , welded, keyed, pinned, to the shaft? Even after I took the tractor apart, I have a hard time believing the friction disc could stick...

I have a Cat 1, 3 Pt Hitch, I want to put a ball on a cross member and mount it between the lower arms of the 3PH. Any have any pics of one they have made? I will build it, but I am thinking of hitch geometry and such? Thank you

When I was a kid back in the 60's,70's, My Dad brought home what I think was a Bolens Gardner. It was a two wheeled walk behind tractor, had a big old cast iron 6 HP engine with a gear reduction out the side. It had #60 chain to a crossshaft with two cone clutches driving down to the wheels with...

Well , I like things to be proper and for my little S373D it means getting 3 tranny gears to put 3rd gear back into it. It bothers me that 3rd gear cannot be used, but the tractor can still be used in 1st or 2nd. The big question is, do I save to get the gears or is that to much to spend on this...

I was reading the operators manual and see they talk about the 3 point hitch being hydraulic? I see a tube running from the rear to the front. Is this a tube coming from a pump driven off the engine? I am going to check it tonight but wonder if any one has checked into the operation of this...

Hi, missing teethI took trans cover off to find 3 gears missing teeth. Any used sellers out there? Thank you

Hi, Eric in Kamloops B.C. Canada. Just signed up to this forum, seems like a very friendly spot with lots of interesting information. Just bought a S373D with a loader front end. It will be a great little unit for snow ploughing, possibly a mower deck once I figure how it would mount? Hi!

Hi, new here, just got home a S373D and obvious transmission problems. After popping the shift cover off, I see several gears missing teeth. Any suggestions as to a good spot to purchase these, or if you think they are even available? It can still be used in 1st and 2nd. Any way looks like this...