The vacuum advance on my Ford 3600 has been broken off since I've owned this tractor about ten years ago. (Over that time, I've though about repairing it, but didn't see the need.) The engine is...

I recently replaced a few seals in the pump. I replaced the: - large o ring on the head = gasket on fuel inlet - main seal(with spring facing inside) - o rings on the throttle and stopper shafts -...

Is the head on a Ford 3600 with different cast/mold numbers interchangeable? Would a D5NN6090G be replaceable by another similar number?

front end loader stuck in raised position, bucket tilt works fine, no leaks, fluid full, seems one arm wants to work but not both, any thoughts ?

I have to change the fuel shut off cable on a Ford 3600. Any suggestions on how to reach the lock nut on the underside of the instrument panel? I can't figure out how to get a wrench on it even if...

Does Ford 3600 transmission oil and diff oil share the same level

1979 ford 3600, recently purchased and have noticed the rear lift is either all the way up or all the way down when the lever is engaged. Has both levers for draft control and lift control. With...

I have a Ford 3600 diesel that I have owned for 7 years. A little more info is, it has the Hydraulic filter on the top of the hydraulic pump. It has the auxiliary hydraulic lines under the seat...

I’m almost embarrassed to post this, but I can’t figure out how to remove the air filter on this thing. I’ve tried pulling it and turning it, but it won’t budge. I figure it’s got to be easier...

I want to replace the heater in the intake manifold that helps in cold starts.I have looked,but cannot find that piece anywhere.I have ordered a new one and it has an electrical...

Took the tractor out this morning, noticed a significant coolant stream leaking from the right side under the starter. It was in the garage with antifreeze in the coolant. I suspect a corroded or...

Hi everyone, I'm pretty new to tractor ownership and look forward to learning and contributing to these wonderful forums. I recently purchased a Ford 3600 and think I may have been taken...

]I have a problem with my 3 point lift arms. They are in the up position and stuck there. When I start the tractor, the pump gets extremely hot, so I am sure it's because of extreme pressure...

Hello new to the forum I did a search but did not see an answer. I'm trouble shooting a no start issue on a Ford 3600, I can jump the solenoid over and turn the tractor over. I have found that...

I have a 3600 and just finished a motor oil change. I used Rotella. I am also going to drain the rear end fluid and the middle which i believe to be the transmission. I was wondering if the rear...

Hello, Ive had this old ford for 7 years, inherited from my passed Unlce, It runs very good, a workhorse. I need to get ROPS for it, insurance related. Any leads on an exact part? Ill contact...

Ok I’ve had a car with a blown head gasket before but this is use has me scratching my head some. A while ago I had issue with what I thought was blow by but now I’m thinking maybe that issue...

i'm looking for service manual ford 3600 any one?

i'm looking for service manual ford 3600 any one?

As I fix one thing another breaks. Lol. I laugh only because I want to cry. Ha! So got valve cover gasket replaced. Went and started the old ford and no more top end leaks. Great! Well then fluid...

I have the IT manual and owner's manual but i cannot find where there is an exploded view of the rear remote hook ups. Do they make a rebuild kit for them as all i have been able to find are new...

Ok This is a new to me tractor and it has done well other than some quirks that i have fixed, am fixing or will fix. However i have a large issue and want to know what (if anything) i can do to...

So i have a new to me Ford 3600. It "had" a stabilization bar on the PTO links,i think. Looking at images online that is what it looked like. I want to go one step up and add better stabilization...

Hello all. Just picked up our first tractor . An 81 (i think have not grabbed the SN yet) ford 3600. Solid running but needs a bit of work that i will get to over time. You know the standard...

I have a green wire coming off each one of my idiot lights. Well there are 2 wires coming off each one but a single green off each one as well. And one has green/blk wire. Where do the green wires...

So I replaced the water pump and thermostat on my diesel 3600. Other than a few skint knuckles no biggie. However I cranked it up today and ran it for about 15 minutes and never saw the radiator...

ANYONE KNOW WHERE TO GET DIAGRAM ON ALL WIRES THAT GO ON STARTER , SOMEONE ELSE TOOK IT OFF FOR ME . I PUT NEW ONE ON CANT GET ANY POWER NOW. I HAVE DONE SOMETHING WRONG CANT FIGURE IT OUT . OF...

TRYING TO FIGURE OUT HOW TO REPLACE MY LATE 70 ,EARLY 80 FORD 3600 DIESEL FUEL TANK . I HAVE LOOKED ALL OVER THE INTERNET,YOU TUBE ,ETC. MY MANUALS THAT I HAVE DO NOT SHOW ANYTHING ABOUT IT . ANY...

1977 Ford 3600 - Gas Engine New to me tractor, was used by the city for snow removal. It has a hydraulic snow blade that is run off what looks to be a Ford factory remote (possibly made by...

So I've got a Ford 3600 that needs a new clutch. Symptoms: Will start in neutral. Gears will grind when trying to put it into gear or engage the PTO. Clutch linkage cannot be shortened any...

I have a Ford 3600 , not sure of the year , its an 8 speed - high and low , my power steering fluid is getting into my tranny some how , engine oil stays same , and clear , but the tranny get way...

Working on replacing the seals and felt pads on the brake pedal rod. I've got the pedals off and am finding it's a keyed rod so I can't proceed further. Looking at the parts diagram it appears the...

I have a 1979-1980 Ford 3600 Diesel with a Dunham Lehr / Farmhand 22 Loader. The loader worked without any problems what-so-ever when parking it back in November for the Winter months. Now that...

Good afternoon. I'm wanting to get a hydraulic top link from Agrisupply for my 79 Ford 3600. Supposedly the remotes are factory. When calling dealers in my area, I get two answers to what size the...

I work on a lot of mechanical stuff but don't really know anything about hydraulics. Can I add remotes to this tractor? There's various remote hydraulics kits for Fords for around $250-300, says...

I am looking at these 2 machines. A 1967 Case 580CK and a 1977 Ford 3600. Both machines have a front loader and a rear 3 point hitch. And are the same price. They are in similar condition. Which...

Hi and thank you for your time. This is for a diesel. I tried searching and found some threads that touched on setting the timing but I haven't found anything that walks me through it from...

I've purchased several TISCO D3NN17365C cables and installed them with the same results: twisted apart within first few seconds of operation. My opinion is this cable is too long at 48" and...

Hey I have a question, I have a Ford 3600 with a bulldog 287 loader on it, I haven't had any problems with the loader at all, but does anybody know the rating on the 287 loader? I have picked up...

Just bought a Ford 3600 that has been sitting for some time.and wondering about the clutch. It isn't completely stuck like most threads I see on stuck clutches. It will release if I start it in...

I am not very well versed in the Ford tractors so I am wondering about the 3600 model, this one has the diesel with the 8 speed transmission. It's a decent looking tractor from the picture, the...

My upper radiator hose gets warm, my lower stays cold. I'm guessing thermostat stuck shut? It is winter in Michigan and I don't push it that hard in the winter, just moving manure from the barn...

Your help is always appreciated! Ive been running this old ford hard for almost two years now. Its done a perfect job until recently. Now old blue wont shift out of gear. I haven't tried High...

Acquired a 3600 this summer. Right away it was slow to start, needed about a full minute of cranking with white smoke coming out of the exhaust. I replaced the thermostart and it got better but...

The Tach on my 1977 3600 just stopped working. I made sure the cable is not broken. The failure must be in the Proofmeter Driveshaft Adapter (PDA). Has anyone replaced one of these? Appreciate...

Hello I've mostly just been on here to read and learn but I haven't been able to figure out from just reading what I need to do to get my set up put together. I've read several posts on here and...

I found a ford 3600 Gas Tractor for sale locally. Are they good machines? Can I pull a NH 268 square baler with that model? Any info would be great thanks.

I just bought a hydraulic remote for my 3600. I am in the process of de-greasing, cleaning, and painting. I am including some photos and have questions about the install. 1. Some of the...

Appreciate some advice on problem with my Ford 3600 tractor. If engine is off and lift arms down and lift lever in raise position, when tractor is cranked, arms raise immediately no matter how...

I have a 1977 3600 that is in need of re-wiring. I have the Ford Repair Manual. The schematic shows a voltage stabilizer in between the key switch and the fuel gauge. The manual says this is...

I have a 1977 3600 with a "C" prefix serial number. Repair manual says I need a 3-position push/pull type light switch. The switch I'm able to find on the web is for the A and B prefix serial...

where is the hydraulic oil drain plug on the ford 3600 ? also where is the fill plug ? what is the correct hydraulic oil for my tractor ?

I have a gas Ford 3600 which was my dad's. I had it running 2 years ago after I replaced the sed. bowl filter element (pricey) and replaced the original carburetor with one of those Zenith...

just got a ford 3600 deisel runs great dont know much about it. it has a oil or hydraulic leak on the left side (if sitting on seat). there is a pump like part in that side and the leak seams to...

I think I'll need to buy tires for my Ford 3600 sometime this year. I think it has the original ones on it to be honest because they are pretty weather cracked but the tread is still decent(tread...

I apologize up front if I am posting in the wrong place really dont know much about forums and posting or how to even find answered questions, so can any help me out with this , cant find anything...

Hi, new member, looking for advice on possibly buying a new (to me) tractor. It's a 1974 Ford 3600 with 3700 hours on it. Has the 8 speed transmission and power steering. The seller bought it from...

Hey guys, I'm new here and I've searched the web over for help but to no avail. Here's my issue - I have a late 70's model Ford 3600 diesel, last winter my antifreeze was a little weak and I had...

Before I take the head off , thought id do a compression test on the engine, but what is the correct adaptor size to use, all the kits I find are in metric m20, m22, m24, the diameter of the...

Hi from essex in the UK. have a 77 ford 3600 with Qcab, its not easy to start and smokes more than it should , its primary use is with a bearcat chipper. My other tractor is a 99 Deutz-Fahr...

Got my Ford 3600 delivered last weekend and have had it working around the farm and am loving it! I tried to post some pics from my phone but the app doesn't appear to be working or maybe I'm...

It was free and figured it should be ok but wanted to ask to be sure.

This is my problem...while trying to change out my hydraulic oil in the rear axle..I removed the pan-head screw(part#38308s36-5/16-24x1/8) instead of the square-head level screw located above...

Any clues as what to do to unlock engine after seating out in the winter?

Hey guys, you've helped me before and now I am stuck again. Bought my used tractor about four months ago and I have been taking it very slow mostly because of bad weather. Doing a lot of...

Hi All, I have a Ford 3600 with no remote hydraulic lines. I am thinking about buying a three point log splitter instead of a gas engine log splitter (one less engine/gummed up carb to...

Looking at a 1981 Ford 3600 diesel tractor. 1700 hrs, 40HP, live PTO, pwr steering, 6x2 trans, real clean looking. They are asking $5950. Any opinions on this machine for bush-hogging 3-4 acres...

Hello all! Just bought an old Ford tractor. Need help identifying it before I buy an operators manual. Model#: CA213C Production Code: 9K19B Serial#: *C626222 My best guess is its a 1979...

Leaver will not lift hay fork. I added two gallons of hydraulic oil and it still does not lift.

Hi All, I'm replacing my bad original Ford 3600 (gas) radiator with an aftermarket radiator. Is there an attachment point/bracket at the top of the radiator somewhere? There are two large bolts...

Well I have had a leak from my fuel filter since I bought the tractor. Not much, but this week it started a steady drip. I removed the fuel filter and found that whoever had changed it never...

Tractor was left out in the weather for about 4 years with cover over exhaust. This is a diesel tractor and I believe it may be seized up. I was told by a friend to jack up the rear end, put it in...

Just bought a Ford 3600, wiring has been altered, (butchered), can anyone tell me how many lugs are on the original ignition sw

Found a business a few hours up the road that's selling a 1976 Ford 3600 diesel, asking $5,500. Transmission has been flushed, new front tires, new instrument panel, new gas tank, and freshly...

What would cause the hydraulic system on the front end loader to stop working ? Rear hydraulics are working fine. Bucket is locked up and won't go up or down. Fluid is full and hose clamps/lock...

Anyone have any experience with a loader on a Ford 3600? I'm considering a new installation but don't want to hurt the front end with the additional load, if it is not designed for that. Thanks...

Guys, Anyone have any experience with a loader on the Ford 3600? I am inheriting one with about 1500 hrs, and would hate to install a loader if the front end won't hold up to the loading.

Hi I have a ford 3600 for the last few years always gave me a bit of trouble with the injector pump, would have to tap it to get tractor started but now it wont start at all after been lying up...

Been eyeing this tractor for a couple of weeks now. Dealer about 2 hours from me has it but I haven't had a chance to see it in person yet. I was curious if the price seemed in line for the...

Today I took the top off the pump and put new o-rings on the throttle and kill switch shaft. It ran perfect before this. After I put it back together I can't get it to start. It is getting fuel...

My fuel gauge reads empty regardless of the fuel level, and the temp gauge goes up to the edge of red and stops ( no evidence of any overheating). I would appreciate any help to diagnose whether...

An embarrassing question to have to ask but here goes. I bought an older ford diesel 3600. It is probably about a pint or more low on oil. The dip stick and oil filter is on the left side of...

HELLO, I'M COLOMBIAN FARMER, AND I NEED HELP WITH THE MANUALS OF MY FORD 3600 TO REPAIR. THANKS IN ADVANCE FOR YOUR HELP

I have a Ford 3600 diesel which I have owned for about 2 months. The proofmeter works, has about 1800 hours on it, but who knows if this is correct. Today I noticed what I think is oil which...

HI peeps Before I start mowing for the year, what's the best grade of oil to put in the engine & 3-point system for UK weather? Glen

I just got a Ford 3600, well I purchased the property and it was left. I need to do some bush hogging, but need to add some hydraulic fluid before I start. I can't get in touch with the former...

in need of ford 3600 wiring diadram for diesel father needs a little help

Finally finished my sun canopy. Kinda copied Soundguy's bracket design. Used all "scrounged" material. Top was a piece of metal barn siding. Frame was from steel destined for the dumpster at work...

know nothing about these tractors but might buy one need info on them like are they good. what problems do they have?

I'm looking at buying this diesel Ford 3600 tractor. Seller says recently he noticed while mowing tall grass with 5 foot brushhog, the PTO was barely turning. This tractor has a live PTO. When...

Ive found a 1981 3600 ford diesel has the hydraulics on it, good tires,the paint isn't show ready, its faded and needs a can or two of spray paint on it so some spots want rust but I'm going to...

Hi I am about to buy a 1980 ford 3600 with front loader. 2 owners only, it has 589 hours supposely? How can I make sure that it is correct? (first time tractor buyer) The tractor seems to be in...

I'm considering purchasing a late 1970s model Ford 3600 from dealer. He's asking $5,900 (but "will drop to" $5,500) and it includes a 6' rotary cutter. I have not gone to see this machine yet. Any...

I am curious. I am selling my Ford 3600 with loader and would like some opinions on how to price it. It is in great condition...has about 2000 hours...Live PTO...Rear Hydrolics...and very nice...