I'm having trouble finding a rebuild kit for the steering shafts on my Branson 3510 tractor. I can find new a cylinder but was wondering if anyone knows where I can find a kit, or if there is...

3510 with the Kukje 3T90L engine. I’m looking for a block. A complete used engine would be nice but I can get by with just a block or if there’s another engine that will bolt up and work. I’m in...

It has the Kukje T390L 3 cylinder diesel. I may be in need of a block. Does anyone have one or know where I might find one? I’m located in Northwestern South Carolina. Any help would be greatly...

I've got a rapid drip from the cutoff switch on my fuel filter assembly. Turn the lift-pump on and it starts to drip, regardless of whether the cutoff is open or closed. I suspect that replacing...

Is the kukje 1700 the same as the cumins 1700

Now that I'm getting ready to retire and will have more time to do things with my Branson, I'm wondering about trailering it to places to do some small jobs. I've got an 18 foot Aluma tilt trailer...

I’ve decided to sell my 2004 3510, it’s a geared tractor w/shuttle shift 4x4 with a front end loader and a canopy. I do plan to clean it up a bit, also a few cosmetic repairs will be made. Its...

i have an older model 3510 and the fuel pump went out i was able to install a edelbrock pump from O Reilly’s and get it to push fuel to the injector pump it started and ran but before I could...

Searching for direction on my Branson hydraulics problem. While moving rock with the front end loader I noticed a lot of oil on the ground. I shut it down and discovered I lost the hydraulic oil...

I have looked almost everywhere for the correct seal kit for my hydraulic cylinders. I ordered seals for a BL10a which are not the same. Where can I find the older style seals?

Hey guys, I am Seeking sealant recommendations, my Branson 3510 was leaking around the fluid level site glass (rear of tractor). I parked the tractor on a downhill slope to get all fluid away...

I appreciate the add. I have a Branson 3510i with just under 300 hours on it. I love the tractor and am the original owner. I have found that once the tractor gets to up to normal temp, that I...

Ok I replaced both the fuel pump and the Fuel Filter - including the housing top because the 90 Degree insert on the inlet side came out. This all started when I brushogged a small field (2...

Anyone ever had one freeze up from lack of use? Bought a 400 hour tractor that seems really nice at an auction. The pto speed selector and mfwa levers are frozen in place. The lever arm at the...

i have 2007 branson 3510 that wont start tractor was running then left it parked for a couple week went back to it and then it would not start started investigating the issue found that was not...

Over the past few years my (now 15 yr old) Branson 3510 has reduced power when in 4 wheel drive. Almost feels like the brakes are hanging up, once I take it out of 4X4 the tractor is fine. Anyone...

I was moving 5 loads of dirt with box blade Saturday and noticed temp was higher than usual, just barely passed the halfway mark, but kept an eye on it. It wasn't long temp raised almost to first...

I'm not very familiar with tractor or computer, so please forgive my ignorance. I have a 2002 Branson 3510 I have installed (maybe 6 months to a year ago) a new "lift pump" under tractor between...

Hey all, Looking for some advice and info. I'm considering putting a backhoe on my 2003 Branson 3510. I have several questions I was wondering if anyone could help me with. -Will the 3510 handle...

I recently got a 2003 Branson 3510 in nice shape with about 500 hours on it. It is a beefy little beast and joy to work with. I'm going to be moving a bit of snow with it next winter and it is...

Anyone have suggestions on why Branson 3510 has problems starting.

I need to remove the radiator on my 3510, in order to make some upgrades, however, I need to be absolutely certain, as to how it is mounted on the bottom. Typical modern automotive applications...

Tractor won't run above idle. I have a 2005 3510 that I have owned since new and other than a hydraulic hose and the usual fuel pump problems, I have had no issues with it. It has just under 500...

Does anyone have dimensions on the ball joints taper, and thread size on the tie rod ends? Or equivalent part number for generic replacement? I am aware the factory has upgraded to larger size...

When I bought tractor new in checking front differential fluid level wouldn't touch dipstick. sent back to dealer who went thru it couldn't find any leaks. At 50 hrs changed all fluids , front...

I have a Branson 3510 which will not go into Gear either forward or reverse. Everything else works fine. I checked the linkage and it looks like it is order. I drove it up here five days ago...

I just purchased a farm where the Branson 3510 came with the farm. I am new to this and need to know if there is a specific type of oil that I need to use when changing the oil. And then secondly...

Hey Folks. I have a leaky hydraulic site glass. In my parts catalog has it listed as TCA9130000A4 , but I can't find that part on any site (I've seen other part numbers, but don't have a way to...

Hey Folks. We farm about 4 acres and are starting to add more levels of mechanization. Last year we added some potato hillers, but by the second hilling the tractor was brushing the plants. Is it...

What will it require to add a hydraulic line (pressure and return). I want to get a 3-point hydraulic log splitter. Where are the locations for installing lines to the rear of the tractor? Will...

my fuel tank leaking a the base of the fill neck dose anyone know what type of plastic it made out of. i want to weld it

Went out to the barn this morning to plug the engine block heater in. Pulled the hood unlatch cable and found that the hood would not unlatch. When I pull the cable I can hear the a noise from the...

I have a Branson 3510 purchased new in 2006. Have 583 hours on it and the clutch is slipping bad. I have adjusted the clutch out all the way until there are no more threads. My question is this...

I have a Century 2535. The wiring to the ignition and fuel stop solenoid have burned up. Does any one have a wiring diagram that they could send to me? I've had no luck with Branson or any one...

My power steering blew a seal on the PTS Cylinder Assy. How do you remove the Cylinder Assy. Where Can I Buy A new one or get the old one repaired Appreciate any help on this problem. Where Do...

A nearby dealer has a 2004 Branson 3510 in great condition. This has a 35 HP 3 cylinder diesel, 12F/12R shuttle transmission, select able 4x4 or 2x4, PTO, 3 point hitch, tilt wheel, adjustable...

I have a couple questions in adding remotes to the Branson 3510i. I understand that you tap into the circuit on the rear of the tractor for the remotes. Does anyone know for sure what the fittings...

Hi Folks, I have followed this forum for many years and this is my first post. I have a Branson 3510 that runs like a charm. On occasion the stop solenoid sticks and I have to push the the stop...

Hi, I have an issue with my 3510i. It won't run at higher rpmsfor long, it slows way down, then picks up again. I checked all the fuel lines and the lift pump. The lift pump seem not to be...

Both FEL and rear lift arms are jerky when being raised and I can feel little thumps when I operate the hydaulics. Clearly the pump is fluid starved and cavitating. Also feel the thumps inthe...

I have a Branson 3510i with the Kujke AN1700N2 engine, and all 3 glow plugs test bad. The Branson # for the plugs is HK15170000A4, and the dealer price is obscene for this little plug. Does anyone...

Transmission for a Branson 3510. 12 speed, 4x3 Howell, Mi

Brought my Branson to the dealer to have to reverse adjusted and they said the transmission is crack completely in half. I bought it new and it now have 600 hour on it. But off warranty. Does...

Hi, Just found this site on a google search. i have a Branson 3510 taht i bought about 6 years ago. The John Deere dealer won't work on it so i am going to have to try to do it myself.

Hi all, First post here. I owned a JD Model M (late 40's model) for 15 years and a Belarus 31 hp (AS250) since it was new in '89. I made a mistake when I bought the orange tractor, though. I...

I have a Branson 3510 with about 250 hours on it. Earlier in the week I was mowing the lawn and after about an hour or so the engine suddenly got weak. Went down to a very rough idle with no power...

I just replaced a bad hydraulic line on my Branson 3510 backhoe, and now all backhoe and front-end loader functions are slow and weak. I expected a little trouble with air in the lines, but...

Hey Guys, I've got a Branson 3510 with the 3T90L-ATC motor. It cranks and runs, but it's making a metal-on-metal loud tap-tap-tap that I think is isolated in the front cylinder. My feeling is it's...

If I am doing dirt work I have no problems the problem is when I am brushogging..When I am done I can either shut it off or let it cool down first either way after I shut it off it will not start...

My Branson 3510 has 850 hours. The dealer that sold me the tractor is no longer in business. The nearest dealer is 138 miles. I called and there and had to leave a message 5 hrs later and no...

I used it today and when I slowed down the pto sounded like it is ratchiting so I went on and slowed down again it did the same thing I had the brush hog hooked up by the way this is the first...

I think I probably have a bad injector on my 3510. I was hoping someone out there would have some experience with these injectors and hopefully a part number to cross reference. The motor in this...

I'm having some persistent problems with air getting into my fuel line. I'm able to bleed the lines, which is easy on this model, but after starting up, the motor runs weakly and instead of...

Does anyone have a source for tire chains? I have 28x8.50-15 fronts, and 43x16.00-20 rears, both are Tractionmster OTR's (originals). I haven't found chains for those sizes online, and my dealer...

I bought a 3510 from a dealer about 18 months ago in anticipation of using it to landscape a new house we were going to build. It had 35 hours on it and was traded in on a larger tractor. Didn't...

When I first get on my Branson 3510 it seems as though the brakes are hanging up making movement rather sluggish. This seems to go away after the machine warms up and moves around a bit. Anyone...

This might be a stupid question. Why is there two oil filler caps on the engine? One is in the normal location top of engine the other is on a seperate assembly on the right side of the engine...

Reading posts here I could swear people have mentioned finding shavings in the pre-filter screen of a Branson 3510. I find no mention of this in the manual, nor of a "Magnetic plug". Since I'm...

Hi I am new here. I have a new Branson 3510. PTO would not engage, dealer says to adjust the free play on the clutch pedal for 1". It already appears to be adusted at 1", tightened it a little...

Anyone know the part number for the engine oil filter for a Branson 3510? Last year my dealer sold me a YN148 which was identical to the one that originall came with the tractor. This year they...

century-ML-871696-ML- Branson specific thread.

I have been looking for a good used tractor with a loader. I have looked at used tractos from major mfgr's and yesterday found a Branson 3510 with BL107 loader and loaded Ag tires for $13,500...

I recently purchased a new Branson 3510 along with a Kodiak 5' bush hog. Last weekend I took the tractor down to my property to begin clearing a future homesite. After 2 hours of bush hogging...

Did my first 50 this weekend on my Dad's 3510. Just a few quick things of note. Oil Change - Wheels hard left and FEL full up make filter access and refilling a lot easier. I discovered the...

I picked up my new 3510, R4 tires, no FEL or Backhoe, on 5-14-05 and brought it home to my 2 acres. I hooked up an old rusty bush hog I had and trimmed the areas in the back that I have been...

I am going to go with either one of these.I know they have some differences but ther capabillities are about the same.With implements the branson is 600 dollars more.Could the brain trust get me...

Looking to buy a 3510 with loader. Will this tractor handle the front mounted root rake? I did not know they made one for a small tractor until today and was impressed. What price should one...

Okay everyone! Here is my narrowed done list: Branson 3510 Sync, Mahindra 3510 Sync and Kubota L3400DT. Let the opinions and expertises fly and don't hold back!! Thanx in advance, Bob

Just sold my '61 Ford 601 (2WD, no FEL) for a new Branson 3510 4WD /w FEL. Although it's way more than I need for my 4 acres, I love it! BUT - where the heck can I install a tool box? No room I...

I had done a great job plowing the road -- over a mile of steep, winding, gravel road under 10 inches of new snow -- and was maybe a hundred feet from my own drive, when I just floated on my R4's...

Time to do a little driveway and private road work on my property. Up to now, I've used a box blade but I've been looking at a grader blade to finish up. My box blade is a 5 footer but I thought...

All you guys and gals out there have convinced me that the Branson/Century is the way to go. I have read about everything that has been posted. I'm just about ready to "pull the plug". A local...

I have been using Ford 5000, MF 135 etc and am considering purchasing a Branson 3510 to work a small horse farm. As you all know a loader is essential for this and I have always been able to get...

We just mounted this top and tilt with remote on a 3510 before delivering this TLB to a customer. It's best to never use a tractor equipped with TnT unless you are ready to buy the option. Very...

I have my branson 3510 for sale,it has a branson loader and 10 hrs. on the meter

century-ML-263166-ML-

Just bought a Branson 3510 with Branson loader after much looking. I must say the posts here were a factor. Compared JD, Kioti, Eicher, etc before deciding on the Branson. I really liked the...

Looked at a Branson 3510 today. Was just driving by a shop and looking at used tillers and around the side of the building was a brand spankin new 3510. Was it nice. had a finish mower attached...

century-ML-240613-ML-