OP
metalbender
Veteran Member
A couple more pics.Snow痴 coming
- Thread starter metalbender
- Start date
- Views: 15512
A couple more pics.
OP
metalbender
Veteran Member
Yup, have a few mousers here.
Hay Dude
Super Star Member
- Joined
- Aug 28, 2012
- Messages
- 18,688
- Location
- A Hay Field along the PA/DE border
- Tractor
- Challenger MT655E, Massey Ferguson 7495, Challenger MT535B, Krone 4x4 XC baler, (2) Kubota ZD331’s, 2020 Ram 5500 Cummins 4x4, IH 7500 4x4 dump truck, Kaufman 35’ tandem 19 ton trailer, Deere CX-15, Pottinger Hay mowers
We had ZERO snow last year. First time in my 50+ year life Ive ever seen that. We usually get 4-8 dozen snowfalls per year of 1-10? It was a big hit to the bank account not having any snow to plow.
Im going to have to go through my equipment in the next few weeks. We run an 08 F-350 with a 8.5 Western plow and Tailgate salt spreaders and a Kubota farm tractor with a 9 Arctic poly snowplow and big snow bucket.
Im going to have to go through my equipment in the next few weeks. We run an 08 F-350 with a 8.5 Western plow and Tailgate salt spreaders and a Kubota farm tractor with a 9 Arctic poly snowplow and big snow bucket.
Hilbilly
Veteran Member
Looks great! I'm hoping you get some snow soon so I can see it in action.
In an earlier post you mentioned something about a video but with a "?" mark. Is that suggesting you can't post a video?
oosik
Epic Contributor
That unit you have constructed looks very similar to the setup installed on the 2009 Kubota M7040 I saw in the the dealers shop. As I remember - the entire setup cost right around $14K. Only the school district with federal tax $$$ could afford such a setup. Brand new M7040 and this shaft drive front mount blower.
As predicted, our weather has warmed back up and the 4" of snow is all gone. I see that rain is predicted for later this week.
As predicted, our weather has warmed back up and the 4" of snow is all gone. I see that rain is predicted for later this week.
OP
metalbender
Veteran Member
Tried putting up a couple short vids but no go. Not you tube, just off the reply icons.
dragoneggs
Super Star Member
- Joined
- Jun 9, 2013
- Messages
- 13,627
- Location
- Seabeck, Washington
- Tractor
- Kubota BX-25D, Kubota Z122RKW-42
I haven't had success other than posting via YouTube.
Hilbilly
Veteran Member
Ditto. It was the only way I could post videos here, so I uploaded them to YouTube. Took me a bit to figure it out but all is good and easy now.
OP
metalbender
Veteran Member
Weather forecast is for a major blizzard this weekend. Almost two feet of the white stuff has been ordered, I think off Amazon by a local farmer. Much needed moisture for the prairies. I have two end caps for sprocket shafts to spin on the lathe and one weld to finish this off. A trip for some extra fuel for the tractor and gas for the generator is also in order.
oosik, I will check what receipts I have to see a cost on this project. Pretty sure it is under the $2 k mark. Got a smokin deal on the blower at the local Kubota dealer. Just over $900 for the blower, $230 for the ssqa plate and $100 and a bit for the shaft. Prob another $100 for the 2x3x .125 rails. Bearings, sprockets, chain and a couple pto adapters don't add up to a lot.
oosik, I will check what receipts I have to see a cost on this project. Pretty sure it is under the $2 k mark. Got a smokin deal on the blower at the local Kubota dealer. Just over $900 for the blower, $230 for the ssqa plate and $100 and a bit for the shaft. Prob another $100 for the 2x3x .125 rails. Bearings, sprockets, chain and a couple pto adapters don't add up to a lot.
