I'm adding a second rear remote to my Mahindra 2665, and I will need longer studs to accommodate the two valves. It's an M10-1.25 stud, and I'm looking for a 195-200mm stud to fit. So far, McMaster, Graingers, Fastener mart have all been fails. Does anyone know a source for long metric studs?
Rear remote studs- Where to find?
- Thread starter OldTrix
- Start date
- Views: 2062
-
- Tags
- rear rear remote
ptsg
Super Member
If all else fails, you can always use all threaded rod.
www.mcmaster.com
McMaster-Carr
McMaster-Carr is the complete source for your plant with over 595,000 products. 98% of products ordered ship from stock and deliver same or next day.
I found a couple places that sell a M10-1.25 x 195mm bolt, one on ebay the other online place called hammerhead racing. Wait and see what I get. McMaster and Grainger, were surprisingly useless, as were most online metric bolt shops, along with my loca. hardware store, auto parts store, and even the old Mahindra tractor dealership.
5030
Rest in Peace
- Joined
- Feb 21, 2003
- Messages
- 28,967
- Location
- SE Michigan in the middle of nowhere
- Tractor
- Kubota M9000 HDCC3 M9000 HDC
Any imported tractor dealer will do, not just your brand.
ptsg
Super Member
After a quick search, I found these bolts: (2) OEM Arctic Cat 1623-718 M10x1.25x200 PT HFH CL10.9 Y&Z Snowmobile Ski Bolt | eBay
Not sure it helps. Maybe going with that part number from Arctic Cat.
EDIT: They have a 190 mm long as well. This one have no cross hole drilled at the end. (2) OEM Arctic Cat 0423-451 M10x1.25x190 PT HFH CL10.9 Y&Z Snowmobile Cap Screw | eBay
Not sure it helps. Maybe going with that part number from Arctic Cat.
EDIT: They have a 190 mm long as well. This one have no cross hole drilled at the end. (2) OEM Arctic Cat 0423-451 M10x1.25x190 PT HFH CL10.9 Y&Z Snowmobile Cap Screw | eBay
Too many Kubotas
Veteran Member
You could get a longer bolt, cut the head off and pick a die of your liking (within reason) to create the missing thread.
The bolts I purchased at Hammerhead were some sort of snowmobile track bolt. Should work. I was hoping to find a hardened stud, similar to what I removed. Given the commonality of these tractors and rear remotes, I was surprised at the scarcity of viable parts. TYM/Mahindra/Kioti/JD, et al have to be buying them from someone...
WranglerX
Super Member
Maybe here...... Bell Metric... If you want metric bolts, nuts, washers, etc: go to a metric supplier.....
belmetric.com
More specific....
belmetric.com
Metric Fasteners & Hardware｜BelMetric
Bel-Metric sells metric hardware & specialty automotive supplies worldwide. Visit our website to purchase metric fasteners, nuts, bolts, screws, washers & more.
belmetric.com
More specific....
M10 Full Thread Stud DIN 976, Class 8.8 Steel
Bel-Metric sells metric hardware & specialty automotive supplies worldwide. Visit our website to purchase metric fasteners, nuts, bolts, screws, washers & more.
belmetric.com
Last edited:
WranglerX
Super Member
Well instead of "stud" try threaded rod....
www.mcmaster.com
McMaster-Carr
McMaster-Carr is the complete source for your plant with over 595,000 products. 98% of products ordered ship from stock and deliver same or next day.
Shenandoah MF1760
Gold Member
- Joined
- Feb 12, 2021
- Messages
- 376
- Location
- Livingston, East Texas Piney Woods
- Tractor
- Massey Ferguson 2020 MF1760M
Not a stud, but this may be a source for the future if you're not happy with what you've found.
yeah, I found plenty of Ti bolts, for around $30/ea... nope.
I have a set of chinesium bolts as well as the set from hammerhead enroute. Will just have to remove the toolbox to set everything in place with the greater height/length of bolts.
I have a set of chinesium bolts as well as the set from hammerhead enroute. Will just have to remove the toolbox to set everything in place with the greater height/length of bolts.
Shenandoah MF1760
Gold Member
- Joined
- Feb 12, 2021
- Messages
- 376
- Location
- Livingston, East Texas Piney Woods
- Tractor
- Massey Ferguson 2020 MF1760M
I found a number of Chinese sources, but I'm loath to send anyone to them. I have worked for a Chinese company and they'll try to get away with anything they can. This is freely admitted to by the Chinese nationals I've worked with. I wouldn't trust a grade 8 bolt of theirs to be anywhere close to grade.
