Post puller
- Thread starter ehcrain
- Start date
- Views: 11266
herm0016
Platinum Member
i use Amazon.com: Powerfields T-Post Puller Plate: Industrial & Scientific
a plate with spot for a chain or use my hilift jack. works fine.
a plate with spot for a chain or use my hilift jack. works fine.
grsthegreat
Super Star Member
i like that. i think ill make one with the plasma cutter. i have lots of scrap plate lying around. i usually just wrap a chain around post and clip to hook on bucket.
CoyPatton
Veteran Member
- Joined
- Aug 10, 2015
- Messages
- 1,587
- Location
- Poplar Bluff, MO
- Tractor
- Yanmar YM2002D with Koyker 110 FEL
I have used a strap and a chain both on various types of post with good results. The selection process of strap vs chain is typically based on the type of post/lack of damage wanting to do to the post.
Several factors to consider:
1) rear ballast is extremely important as the resistance of the post will want to pull the rear tires off the ground. Also if pulling from a corner of the loader is the tipping factor!
2) while T-post are fairly easy to straighten, it is relatively easy to break round, square, and wood post. The simple fact of raising the loaded changes angles and the pressure of the post creating bend on metal post and breaking on wood post. This is often at ground level, but can result in pieces above ground level which is likely to be unacceptable and create additional work.
3) concrete set post make all of the above more likely to occur.
On chain or strap wrap your post/chain in a manner that you pull from the bottom of the wraps and as pulled it tightens on the post. Wrap several times and low enough that the length of strap or chain allows the bucket/forks/whatever to begin the lift just above the top of the post. The bucket against the post increase the risk of bending/breaking.
Several factors to consider:
1) rear ballast is extremely important as the resistance of the post will want to pull the rear tires off the ground. Also if pulling from a corner of the loader is the tipping factor!
2) while T-post are fairly easy to straighten, it is relatively easy to break round, square, and wood post. The simple fact of raising the loaded changes angles and the pressure of the post creating bend on metal post and breaking on wood post. This is often at ground level, but can result in pieces above ground level which is likely to be unacceptable and create additional work.
3) concrete set post make all of the above more likely to occur.
On chain or strap wrap your post/chain in a manner that you pull from the bottom of the wraps and as pulled it tightens on the post. Wrap several times and low enough that the length of strap or chain allows the bucket/forks/whatever to begin the lift just above the top of the post. The bucket against the post increase the risk of bending/breaking.
bullbreaker
Elite Member
ruffdog
Super Star Member
- Joined
- Dec 31, 2011
- Messages
- 11,549
- Location
- southern wisconsin
- Tractor
- Bobcat Toolcat 5610G, Deere X744, Cub Cadet IH 982
It works great to connect a chain to a strap or to pull rerod stakes too.
shooterdon
Elite Member
- Joined
- Nov 24, 2012
- Messages
- 4,835
- Tractor
- 2019 LS XR4140 HST Cab; 2020 Kawasaki Mule SX; 2021 Bad Boy 54" ZT Elite
Here is what I use for posts and small trees:
MTL X-Series Tree Post puller - John Deere loader Mount or Euro — MTL Attachments
It will shear a small tree if you are not careful and bend a T Post. Mine was a black one...no green permitted on my LS LOL
MTL X-Series Tree Post puller - John Deere loader Mount or Euro — MTL Attachments
It will shear a small tree if you are not careful and bend a T Post. Mine was a black one...no green permitted on my LS LOL
