One mistake that could have been my last

   / One mistake that could have been my last #1  

Rice Rider

Bronze Member
Joined
Apr 14, 2009
Messages
57
Location
Virginia Beach and Lexington Virginia
Tractor
Kubota L3400 HST 4WD
After reading several pages of the safety forum, I thought I would throw in my newbie story. About a year ago when my tractor arrived, I was anxious to get some work done on it right away. Although most of my property is sloped, there were some good slightly level areas that looked good to clear for our shed, fire pit, etc. I was amazed at how much power the tractor had for pushing dead wood and debris around. At this point I was only using the FEL as a dozer and was not really lifting anything. I had cut down some smaller trees around four to six inches and was pushing several of them into a pile. One of those trees was long enough to get hung up on a larger tree that was still standing on my side as I was pushing, and then got hung up on another tree, this time along the leading edge. When the tree I was pushing caught the second hang up, a bind occurred and the tractor bogged down a bit so I looked down, saw the bind and thought what a pain it was going to be to get off in the brambles and either cut the tree or try to pull it out from between the two trees that were holding it in place. Instead of getting off, I figured that the tree would just break in two if I backed up and gave it some more throttle. When I did this, the tree did not break. I had not backed up again and the tree was now loaded like a sling shot. I lifted the FEL figuring that might help and that was all it took for the tree to instantly come over the FEL across the hood and hit the steering wheel saving my rear end from having the tree hitting me square in the chest and crushing me against the seat. It also hit the throttle and pushed it all the way on so before I shut it off, it was pushing the tractor against the tree at full tilt. It bent the steering column and pushed it away from the instrument panel. I was alone in the middle of the woods with no cell pone on me at the time. After a few explicatives and feeling very lucky and stupid at the same time, I just sat there and thought how easy it would be to die on this tractor. This simple newbie mistake could have killed me.
 
   / One mistake that could have been my last #2  
WOW. That IS scary.

My Newb story is similar to another poster thanking his lucky starts for ROPS. I was pulling some saplings out with a chain. Without thinking about how tall they were or the leverage involved, I tied the chain to about six or eight and drove off - slow, steady pressure. The saplings bent a bit, bent a bit more, and then suddenly popped out of the ground brining the tops down horizontally at an alarming rate to where they smacked the top of my canopy and ROPS. They were about 10' taller than my chain was long.
 
   / One mistake that could have been my last #3  
After reading several pages of the safety forum, I thought I would throw in my newbie story....... and the tree was now loaded like a sling shot. I was alone in the middle of the woods with no cell pone on me at the time. After a few explicatives and feeling very lucky and stupid at the same time, I just sat there and thought how easy it would be to die on this tractor. This simple newbie mistake could have killed me.

All I can say is....WHEW! You were lucky! Shows to go how quick things can happen.
 
   / One mistake that could have been my last #4  
They were about 10' taller than my chain was long.

I've wondered if I was the only one who ever did that. I was 13 or 14 years old when I was using our little 1940 John Deere L to pull dead trees to a pile for a big weiner roast for a church group. I had pulled several small ones, but there was a big dead oak tree still standing in the pasture. I hooked my chain to it and tried to pull it down, but the little tractor just spun its wheels, so I pulled a really dumb kid stunt. I backed up to the tree, took off at full throttle, with my foot poised over the clutch, so when I hit the end of the chain, I also hit the clutch so I wouldn't kill the engine. And that big oak tree came down right beside my left tire. Two feet to the right would have destroyed both me and the tractor.
 
   / One mistake that could have been my last #5  
Yikes..darn glad your still w/us.

Most scary for me when Farmall H broke traction,trying to hold back almost trailer cord of wood going down slope..whew what a ride out.
 
   / One mistake that could have been my last #6  
Ahh stories... Ill add my own brush with death and trees.

Trees when put under force, blown down in a storm, pinned between something ect. are sneaky. You as a person, can not see stress, strain, bending force, or weight. The only thing you can see is deflection or the amount that something is bent, that does not ever give you an accurate picture of the force involved. I once cut a tree that was blown over in a storm that had a root ball attached. When I cut the trunk of the tree, the root ball rolled back into its origional positon. That woulda been fine, except that I was standing on the root ball. I looked at that before I cut the tree, but I never thought it would roll back the way it did. When it rolled back, the portion of the tree that was attached to the ball came and hit me SO hard it threw me clear of the ball. (imagine stepping on a garden rake how the handle comes up) It was a decent sized tree, the ball was taller then me (6') when it was on its side. It hurt to breathe for a days after. The chainsaw was thrown clear too, and still running on the ground.

Charlie
 
   / One mistake that could have been my last #7  
I'd say you got away with it learning from your mistake, until someone got you on film with your pickup the next day........
 
   / One mistake that could have been my last #8  
Ive been clearing land with a dozer since I was a 14 so has my brother and dad. Weve all seen and experienced some of the bad that comes with clearing. My dad had his head busted open when a falling root ball pulled his TD20 over and dropped him. My brother had to work up to dark one evening for his boss and had an oak tree in the bucket of his PC300 about to swing around and place it into a brush pile. He had it balanced and it rolled and one limb entered the cab and hit his crowd lever. It started pulling the limb into the cab and as this happened other limbs started to com into the cab . He tried to reach the igniton but a 300 is fast and when he scrambled out he pulled up the safety lever and it disengaged the controls.
I had a 30 foot pine pole about 5 inches at the base and it had binded. I was having to push up hill to clear a small area to turn a scraper around for stripping topsoil on a blind corner. I wasnt getting much traction so I was pushing smaller piles up to a main pile and then I got the pine tree binded up. I didnt know it was holding down a 3 inch tree was bound up in my path. Theres a small gap between the tras and the boderdy ot the dozer. About time I raised the blade to spill and accumulated dirt and seperate the brush that 3 incher sprung into that gap and pinned my shin to the battery box panel. I almost fainted it hurt so bad.
Alway be careful when clearing. or in the woods in general. Theres alway too much to watch and you can always see a springloaded tree.
 
   / One mistake that could have been my last #9  
When I had my HD11 bulldozer I was making driveway accesses to our new road.
Typically I would raise the blade high and bull the trees over forewards and then with blade against the rootball push them out of the way off into the bush.

Well a few maple saplings (maybe 3-4 inches or so) got kinda tangled up so I took the chainsaw to cut them to shorter lengths to be more managable.

I kinda stooped and cut upwards and heard a sudden CRACK and that sapling swung out like Babe Rooth going for a home run.

I swear that that sapling brushed my hair as it flew past!

Got back on the dozer with wery shakey legs I'll tell you.

Very hard to guesstimate the built up energy or the path a bent limb can take.

So be careful out there!
 
   / One mistake that could have been my last #10  
After Katrina I had a 50' cedar tree laying across my driveway. I started cutting off the top 30' to clear my drive. This section was about 5' off the ground so I found I could cut it easiest if I stood on the trunk of the tree while cutting.

When I was just about through the trunk something told me to get off the tree and finish cutting it from the ground. I got down and touched the chainsaw to the trunk, heard a huge CRACK, and the top broke off and the base of the tree sprung upright from the root tension like a slingshot. If I had been standing on the trunk it would have thrown me over the house.
 
   / One mistake that could have been my last #11  
TREES,....pushed,..pulled, cut,..roped,..chained,..dead, alive, rotted, healthy, frozen, or even left alone standing there minding their own business,...when a "tractor" gets involved,.. remember, .. for every Action,....there is ..USUALLY,.. a RE-Action !!!

Sometimes it's good,..sometimes it's not so good,...sometimes you even think, ..Hmmm,.. no reaction. Wait for it,..Watch for it,..Listen for it,..Prepare for it, just be very careful of your "NEXT" move, . . "that's" what could trigger it !! (as some have already testified) (why even chained together at a slight angle,...an innocent downed tree just sitting there,..with just a little encouragement, can "lurch" ahead pulling your tractor over on its side!)

CAUTION ! ....Tractors and Trees,..can be very dangerous when "mixed" !! Just ask any logger, tree trimmer, bush worker,etc,..OR ~Tractor Owner~ who've learned from close calls.

Of course this "danger" includes axes, chain saws,....and matches,..but this discussion concerns ~"Trees and Tractors"~ so lets try to stay (close) to the topic as there are "plenty" of scary "lessons" to engage us awhile. Just "ONE" more TRACTOR related topic for Extreme Caution !!

CHEERS!
. . tug
 
   / One mistake that could have been my last #12  
When I was just about through the trunk something told me to get off the tree and finish cutting it from the ground. I got down and touched the chainsaw to the trunk, heard a huge CRACK, and the top broke off and the base of the tree sprung upright from the root tension like a slingshot. If I had been standing on the trunk it would have thrown me over the house.

Can
Not
Stop
Myself....

If you had flown like Super Man over the the house...

Would you have screamed T A L L E Y H O !

:D:D

Sorry I could not resist!

I had a tree fall up once. Yep UP!

The tree had been knocked down and the ball was out of the ground. I started limbing the tree. As I cleared off the top I could feel the trunk moving slightly. I finally made cut the limbs off and cut a section of trunk. This changed the balance and that tree righted itself. Went straight up. :eek:

Got a few near misses with using a chainsaw... Spring poles, barber chairs, ...

Later,
Dan
 
   / One mistake that could have been my last #13  
After Katrina I had a 50' cedar tree laying across my driveway. I started cutting off the top 30' to clear my drive. This section was about 5' off the ground so I found I could cut it easiest if I stood on the trunk of the tree while cutting.

When I was just about through the trunk something told me to get off the tree and finish cutting it from the ground. I got down and touched the chainsaw to the trunk, heard a huge CRACK, and the top broke off and the base of the tree sprung upright from the root tension like a slingshot. If I had been standing on the trunk it would have thrown me over the house.

WOW! Scary story, good thing you had that intuition and followed it. I could jsut visualize the situation by the way you described it.
 
   / One mistake that could have been my last #14  
Can
Not
Stop
Myself....

If you had flown like Super Man over the the house...

Would you have screamed T A L L E Y H O !

:D:D

Sorry I could not resist!

I had a tree fall up once. Yep UP!

The tree had been knocked down and the ball was out of the ground. I started limbing the tree. As I cleared off the top I could feel the trunk moving slightly. I finally made cut the limbs off and cut a section of trunk. This changed the balance and that tree righted itself. Went straight up. :eek:

Got a few near misses with using a chainsaw... Spring poles, barber chairs, ...

Later,
Dan
This is so funny I'm laugin out loud giggling. The part about superman I could just visualize... soooo funny.
 
   / One mistake that could have been my last #15  
It would have been like getting shot out of a cannon and if I was conscious I'm sure I would have screamed, but it wouldn't have been tallyho! :eek:

If the takeoff didn't kill me. I'm sure the landing would have.

The only funny part of it was having people try to guess how I cut off the top of that 20' stump in the yard.
 
   / One mistake that could have been my last #17  
Couple of summers ago, a good storm blew over about 20 feet of mature cedars that lined our shoreline and left an ugly mess of exposed rocks.
Having had prior experience with springing catapult trees, I used this to my advantage.
Standing safely to the side I topped each cedar gradually 'till they sprung to the upright
position.
The cedars grew new heads and today you'd never know that the had blown over except for the fact that they had been pruned at the top.
 
   / One mistake that could have been my last #18  
I dont feel so bad now. Durring a long night of Fire dept calls during a hurricane, we must have cut over 100 tress off houses, across roads, and yes even on downed power lines. about 3 am we had a BIG pine blocking a highway, power lines were clearly broken tree was held up by phone and cable lines. I cut top about 4 feet from wires, then went to cut low side as close as I could reach. head high about 4 maybe 5 feet from wires this left a 8 or 9 foot section of log that I thought would be left on the wires that we could drag off with the big red truck. WRONG as I cut through that log the 8or9 ft peice SHOT into the air like a twig. It might still be in orbit! I was unsure wich way to run so I just stood there with a dumb look on my face.
 
   / One mistake that could have been my last #19  
I've posted this picture before, very appropriate for this topic.

Long story short, luck is the only reason I did not get hurt, thought nothing of it, lack of experience.

I've been lucky on a couple dead limbs dropping on ROPS as well.

Joel
 

Attachments

  • 350B tree on ROPS.jpg
    350B tree on ROPS.jpg
    358.3 KB · Views: 369
   / One mistake that could have been my last #20  
After Katrina I had a 50' cedar tree laying across my driveway. I started cutting off the top 30' to clear my drive. This section was about 5' off the ground so I found I could cut it easiest if I stood on the trunk of the tree while cutting.

When I was just about through the trunk something told me to get off the tree and finish cutting it from the ground. I got down and touched the chainsaw to the trunk, heard a huge CRACK, and the top broke off and the base of the tree sprung upright from the root tension like a slingshot. If I had been standing on the trunk it would have thrown me over the house.

Yeah, this is a fairly common accident when someone cuts the top of a pinned tree with the trunk under tension. A friend of mine did the same thing once while standing on the ground. He had alot of experience in the woods too and it still happened to him because he was moving to fast and not thinking. As he was completing the cut the tension released and the chainsaw was ripped from his hands and propelled through the air like a missile. Luckily he was not hurt and no one was nearby. He even said he knew it was under tension but was shocked at the force it had in tearing the saw from his hands.:eek:
 

Marketplace Items

UNUSED ZJG ZJ-12 EXCAVATOR (A60430)
UNUSED ZJG ZJ-12...
Brock 60'x26' Flat Bottom Grain Storage Tank (A57148)
Brock 60'x26' Flat...
2009 Peterbilt 335 Cab and Chassis Truck (A55852)
2009 Peterbilt 335...
2025 CFG Industrial QK18R Mini Excavator (A59228)
2025 CFG...
Hyster 60 6,000lb Diesel Forklift (A59228)
Hyster 60 6,000lb...
2021 SANY SY265C LC LONG REACH EXCAVATOR (A59823)
2021 SANY SY265C...
 
Top