L3200 replacement tool box

[Garandman]

The plastic hinge broke and then today I lost the lid. I'd like to get something a little bigger. I like Pelican cases but they are probably too deep.

Suggestions?

 

[varmint]

My L3400 came without a toolbox, and I looked around before deciding, to once more (I had used the first one on a B8200 some years ago), install a Craftsman $10 plastic toolbox- the size seems perfect, it's waterproof, and has a sturdy hinge/latch arrangement. It is actually a bit bigger than the factory steel toolbox that was on my L3130. I will follow up with a photo tomorrow.

Okay- here're a couple photos- the box fits quite nicely between the fenders. I think it would do the same with a L3200.

 

[s219]

I have been wondering if this would be good for my L3200 if the stock toolbox ever breaks:

Amazon.com : Plano Shallow Dry Storage Box (Orange) : Fly Fishing Boxes And Storage : Sports & Outdoors

Not sure if the side-hinged lid would clear the seat. Need to make some measurements. I have the same box, but tall version, that I use in my boat for tools/etc.

 

[Fallon]

I got a "Homer box" from Home Depot. Just a generic tool box twice the size of the OEM one. Happens to be Kubota orange. Drilled 2 holes in the bottom & mounted. The bigger box barely hits the back of the seat & wiggles a bit due to the extra weight of all the crap I have in it. It works better than OEM but not great.

 

[mddorange]

I bought a Homer Box like Fallon to replace that little waste of a box that came on my L3200 but when I went to replace it I decided that the Homer Box was too large. Instead, I used an old Craftsman tool box that I already had and it fit much better. I then used the Homer Box to replace the Craftsman box and now have more room for both applications.

 

[Garandman]

Still looking...

 

[chim]

I took a different approach. There wasn't any place that really appealed to me for mounting a box on the L3200. Valuable spaces were already taken up by the cab, externally mounted rear wiper and control box for the rear blower. I don't need a large tool box, just a few wrenches, Channellocks, pins, shear bolts, etc. Everything I want fits into a soft tool bag that stows under the left side of the seat. When I built the cab, I used a cow mat to block off the area under and behind the seat and it created a stiff floor there.

It stays dry, no brackets to build, nothing to vibrate loose over time.

EDIT TO ADD: Just noticed the wood showing in the pic. That's not part of the cab fab [grin]. That's the "Unclogger" for the snow blower made from an old baseball bat that I ran through the saw at work to make it about an inch thick. The end is now chisel-shaped.

 

[kg7il]

I just cut a piece of piano hinge and pop riveted it in place.
Works fine, fast simple fix.

It is still going strong. but still still small and still too dirty

 

[Garandman]

I just cut a piece of piano hinge and pop riveted it in place.
Works fine, fast simple fix.

All I need is the lid....

 

[s219]

The only thing I would consider is whether the mounting strut can take the leverage of anything taller or heavier than the stock toolbox. It's fairly sturdy with the stock box, but it's still a pretty small piece of steel and will flex.

 

[Fallon]

The only thing I would consider is whether the mounting strut can take the leverage of anything taller or heavier than the stock toolbox. It's fairly sturdy with the stock box, but it's still a pretty small piece of steel and will flex.

My Homer box makes it twist a bit. Much bigger or heavier would pose problems I bet.

 

[Garandman]

I tried one of the plastic cans and the bottom isn't strong enough and it's a little too narrow.

I'm going to use a USGI .50 Cal can painted orange. Kubota Orange seems to be the same as Ariens Orange, which means it's the same as Chevy Engine Orange, which is $5 a can.

 

[kubotacres]

This is what I'm going with when my OEM plastic box breaks. Looks sturdy.

https://www.amazon.com/dp/B00V3EUMZK/ref=cm_sw_r_awd_F-s3vbFXTQ79H

 

[chim]

This is what I'm going with when my OEM plastic box breaks. Looks sturdy.

https://www.amazon.com/dp/B00V3EUMZK/ref=cm_sw_r_awd_F-s3vbFXTQ79H

Maybe it's just a bad picture, but when I zoom in on the box it looks like someone gave it a thin coat of paint with a brush.

 

[kubotacres]

https://www.amazon.com/dp/B00BW67A5E/ref=cm_sw_r_awd_Q4z3vbP3SPFT2

The photos on my end look good. The above link has three different photos of it.

 

[Gem99ultra]

This is what I'm going with when my OEM plastic box breaks. Looks sturdy.

https://www.amazon.com/dp/B00V3EUMZK/ref=cm_sw_r_awd_F-s3vbFXTQ79H

The box looks good, but I think their $15.50 shipping is absurd. I'd be looking for a better alternative... YMMV.

 

[Garandman]

The box looks good, but I think their $15.50 shipping is absurd. I'd be looking for a better alternative... YMMV.

5A3OR New Kubota Allis Chalmers Tractor Industrial Steel Orange Tool Box | eBay