ID Grain Drill

   / ID Grain Drill #1  

dieselscout80

Veteran Member
Joined
Nov 17, 2007
Messages
2,312
Location
South Carolina
Tractor
New Holland TC45DA
I got a grain drill, but don’t know what manufacturer or model number. It’s 8‘ wide with 12 drops to single disc openers.

The previous owner thought it was a IH number 5, I didn’t find any pictures that match my drill.

There is NOT decal inside the grain tanks/bins.
 

Attachments

  • C7769E1B-9BEB-4496-8FF6-99E8BBACCC47.jpeg
    C7769E1B-9BEB-4496-8FF6-99E8BBACCC47.jpeg
    5.7 MB · Views: 186
  • 48A407A2-F5B4-4B36-BAF0-56DACC54D39B.jpeg
    48A407A2-F5B4-4B36-BAF0-56DACC54D39B.jpeg
    5.1 MB · Views: 190
  • 822A274F-1DC5-4078-B6C4-FC89811F3978.jpeg
    822A274F-1DC5-4078-B6C4-FC89811F3978.jpeg
    4 MB · Views: 170
  • C7E12B29-C980-4409-992A-4A7BAD968B9C.jpeg
    C7E12B29-C980-4409-992A-4A7BAD968B9C.jpeg
    4.6 MB · Views: 166
  • 819828E9-019F-46FB-8A1A-0492424DFA6A.jpeg
    819828E9-019F-46FB-8A1A-0492424DFA6A.jpeg
    5 MB · Views: 176
  • 159E122D-F533-4D99-95EB-2C81C1E1409B.jpeg
    159E122D-F533-4D99-95EB-2C81C1E1409B.jpeg
    4.6 MB · Views: 168
   / ID Grain Drill #2  
Possibly a McCormick M or MF
 
   / ID Grain Drill
  • Thread Starter
#3  
Here’s a couple of pictures of the grain tank.
 

Attachments

  • 8817D355-6BFC-413F-AC43-0C6481C43C60.jpeg
    8817D355-6BFC-413F-AC43-0C6481C43C60.jpeg
    4.5 MB · Views: 134
  • E3EE00D9-A549-4FA5-AA0C-D652300C65FF.jpeg
    E3EE00D9-A549-4FA5-AA0C-D652300C65FF.jpeg
    3.2 MB · Views: 156
  • 08B79A1E-CD63-4D2D-AC51-F0FD6F52E982.jpeg
    08B79A1E-CD63-4D2D-AC51-F0FD6F52E982.jpeg
    3 MB · Views: 156
   / ID Grain Drill
  • Thread Starter
#4  
Possibly a McCormick M or MF
Here’s a couple McCormick M listing. The tank seems bigger, but that maybe just a function of it being a wider drill.


 
Last edited:
   / ID Grain Drill #5  
I saw those too. The hitch configuration was more of what I was looking at to compare. Yours has the back-to-back angle tongue like the smaller M, or perhaps a #10
 
Last edited:
   / ID Grain Drill
  • Thread Starter
#6  
Could an old drill like this be converted to use a hydraulic cylinder to lift the discs rather than the old mechanical setup?
 
   / ID Grain Drill
  • Thread Starter
#7  
I put a tape measure on it and it doesn’t seem to be 8’wide.

It has 12 drops spaced 7” apart and the discs (single disc) are 81" outside to outside.

The seed box is 7'3" wide.

Question what width is this McCormick M drill considered?
 
Last edited:
 

Tractor & Equipment Auctions

2013 MACK (A50323)
2013 MACK (A50323)
2018 TAKEUCHI TB210R EXCAVATOR (A51242)
2018 TAKEUCHI...
2020 CATERPILLAR 279D3 SKID STEER (A51242)
2020 CATERPILLAR...
2010 Ford Edge SE SUV (A51694)
2010 Ford Edge SE...
2015 KIA Cadenza (A50324)
2015 KIA Cadenza...
INSPECTION (A51573)
INSPECTION (A51573)
 
Top