84” ssqa snow blade on 72” wide tractor

   / 84” ssqa snow blade on 72” wide tractor #1  

Michiganguy

Member
Joined
Aug 10, 2023
Messages
34
Location
Southern Michigan
Tractor
Kubota MX5400
Would a 84” ssqa snow blade turned 30 degrees be as wide or wider than a tractor that has a 72” wide tire track?
 
   / 84” ssqa snow blade on 72” wide tractor #2  
Barely but yes
1705798356524.png
 
   / 84” ssqa snow blade on 72” wide tractor
  • Thread Starter
#3  
Thanks!
I figured there was a formula. I probably was taught it in school but it obviously wasn’t retained.
 
   / 84” ssqa snow blade on 72” wide tractor #4  
I run a 7' ssqa plow on my 72" wide tractor. I rarely angle it at 30 degrees because wet snow starts to push the front end around, and it rolls snow fine at a much less angle.
I recently added side plates on the plow, so this season I don't angle it at all except around turns and to square up to a pile.
 
   / 84” ssqa snow blade on 72” wide tractor #5  
This is my 96" HD Rhino rear blade. I offset and angle when blading snow. Offset because there are a couple drop-offs on my driveway. Offset keeps the tractor a little further away from the very edge. When angled my blade will cut a 76" to 78" swath for light, fluffy snow. Less for wet, heavy snow when I have to angle more.
IMG_0006.jpeg
 
Last edited:
   / 84” ssqa snow blade on 72” wide tractor #6  
I run a 7' ssqa plow on my 72" wide tractor. I rarely angle it at 30 degrees because wet snow starts to push the front end around, and it rolls snow fine at a much less angle.
I recently added side plates on the plow, so this season I don't angle it at all except around turns and to square up to a pile.
So you basically turned it into a snowpusher?
 
   / 84” ssqa snow blade on 72” wide tractor #7  
I suspect You will be running over snow when angled since some snow seems to always roll back from the windrow.
 
   / 84” ssqa snow blade on 72” wide tractor #8  
So you basically turned it into a snowpusher?

A smaller capacity, but yes. I have since added UHMW Polyethylene closing the gaps on the side plates. I plan to remove the side plates for larger snows, as I have several very long drives I plow. 6 bolts and they're off.
On edit, I should add that I fabbed this up based on the work of a TBN user that did a similar modification.
IMG_4630.jpg
 
Last edited:
   / 84” ssqa snow blade on 72” wide tractor #9  
I have a 7'-6" plow on a 6'-6" wide tractor. Same 1 foot difference you have. I run it fully angled all the time. Like dstig1 says - it's close but it works fine for me.

24_1_8-1.JPG



24_1_8-2.JPG


gg
 
   / 84” ssqa snow blade on 72” wide tractor #10  
Adding to the above - if I put an 8 footer on there it would give me less than 3" more on each side when angled. I don't think that is enough to make any difference at all.

gg
 
 

Tractor & Equipment Auctions

2013 Ford F-450 Altec AT200A 30ft Bucket Truck (A50323)
2013 Ford F-450...
2013 Ford F-550 Altec AT40G 40ft Bucket Truck (A50323)
2013 Ford F-550...
2016 E-Z Beever M12R Towable Brush Chipper (A51691)
2016 E-Z Beever...
2010 Ford Edge SE SUV (A51694)
2010 Ford Edge SE...
2010 Ford Edge SE SUV (A51694)
2010 Ford Edge SE...
2018 GMC Savana (A50120)
2018 GMC Savana...
 
Top