I have a little kubota b7510 at my farm. I think the front end loader has around a 400 lb. limit, it is a 272 I think, but what about the 3 point lift?,. My box blade, cultivator, brush hog weight around 400-500lb. each, but what is the limit?. And is there a safety valve that would prevent you from blowing the seals?. New to tractors and could use some advise.
3PT. weight limits
- Thread starter randy1687
- Start date
- Views: 2370
FWIW, the Kubota specs list 3 pt hitch capacity for the hydro version of the B7510 at 615 pounds at lift point and 480 pounds at 24 inches behind lift point. I run a woods GB60 box blade that weighs 495 pounds on my B7610 (which has the same lift capacity as B7510) and I have not had any issues to date.
Brad_Blazer
Veteran Member
Pretty much every hydraulic control valve has a relief built in to prevent damage to the pump and seals, etc. This includes the 3ph control.
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
I wouldn't count on -every- hyd valve having a relief.. but depending on how it taps the tractor system, the tractor system may still have a relief in line.
Dang.. those are some low lift numbers.. how much does that tractor weigh?
soundguy
Dang.. those are some low lift numbers.. how much does that tractor weigh?
soundguy
bigshovel
Gold Member
That can't be right. My little tc 21d is some 1200 lbs. rear lift.
Brad
Brad
RobJ
Elite Member
Find your manual or order one. The exact numbers for your rig are in there. It also some other useful stuff.
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
I agree.. they look real low. At those #'s.. i don't see how it can use most standard 3p implements. My little yanmar 1700 totes a 30" dirt scoop, and I know it must weight at least 200#.. maybee 225#.. I can lift it filled with dirt.. heaped over.. and I'm guessing total weight is nearing 750+ #.. all I need is front weight.. lift don't even groan at all.. yanks the scoop right up.. and that is a little ~19hp tractor
soundguy
soundguy
valleydweller1
Silver Member
It looks like Peter got his kilograms mixed up with his pounds. The 3ph on a B7510 has a lift capacity of 1356 lb at the lift point, 1058 lb 24" back. The 615/480 capacities are for our friends around the world who use the metric system.
http://www.kubota.com/f/products/b7410_Specs.pdf
Greg
http://www.kubota.com/f/products/b7410_Specs.pdf
Greg
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
Well.. that certaintly changes everything..
soundguy
soundguy
lawn_king
Veteran Member
- Joined
- Jun 17, 2006
- Messages
- 1,622
- Location
- Hanover massachusetts
- Tractor
- kubota L 3540 hsdc,B 2320 hsdc & lots of other stuff!
My B7500 3 pt capacity was 1100# if my memory serves, it been a few years since i sold it.