massey ferguson 50

Hello, I'm adding a MF-101 Loader to my MF-50. I ordered the pulley below and my crank pulley has what appears to be three holes with 3/8" threads. What bolts are supposed to be used? The bushings in the pulley I ordered are much larger (probably 1/2"). I've looked for shoulder bolts or...

I have an mf50 that has been passed down to me that was purchased new by my grandfather. Serial tag reads sgw 537382. All of the searches I have done to identify year etc do not show this s/n. Does anyone have any insight or no how to identify?

Cleaning out the home office area and came across this publication. I had bought it used when I acquired a MF 50 back in the 90s. I sold the tractor probably 20 years ago and forgot about the manual. I really have no use for it any longer. It is 50 pages and hole punched for a 3-ring binder...

I have a Massey Ferguson 50 split to replace clutch and pressure plate. Looking for best options for a new clutch and pressure plate kit. The pressure plate has broken bolts and spring pieces that hold the 3 fingers. 11" clutch - tractor serial # 633344 - One big question - in my manual it...

Hi All, I am searching for a manual for what i think is a mf50a or r? The serial number is MF50 836990A, It has 4 clamping cylinders that hold the backhoe in place while digging, one of which is leaking. No agent or dealer so far has been able to tell me what model it is so i can get the right...

What is the orginal colors of a Massey Ferguson 50

was looking at a 1964 mf 50 gas with power steering good tires not restored runs great is 2000.00 a good price

I have a 1962 MF50 4cyl gas tractor. Sometimes when I'm snow blowing in reverse the left rear wheel locks up. Forward is OK. Go back and forth and the wheel frees itself. I've disconnected the brake rod and have had the wheel off. All looks OK. I don't think this happens in the summer but I...

Hello all, I'm new here, so I think a small introduction would be good. A couple of months ago I have bought a 1971 Massey Ferguson MF50 industrial (backhoe) tractor, here in Sweden. The label actually mentions the type MF50R, but I think that might be the name the Swedish importer gave it (I...

I Have a MF50 split to install a new clutch (dual). The reason for the split is the PTO fiction plate was completely burn out and shredded. With the tractor split should I be able to turn the PTO shaft by hand? I don't want to put it together again just to burn out another plate.

Hi all, I bought this MF50 Z134 a couple years back because it had a loader and it was (I thought) a good price but non running condition. The guy said the starter went bad and while replacing it he dropped a nut into the flywheel, then he got sick and it's just sat since. When I drained the...

I have lost most of the hydraulic oil out of what appears to me to be a weep hole in the bottom of the transmission gear box. Any help solving this would greatly appreciated. I'm brand new to the world of tractors. I've replaced the hydraulic pump and and replaced the seals in the top of the...

My block heater packed it in at minus 33 so I bought temro circ heater was going to cut the hose supplying my cab heater which is coming from low point on motor and splice in and out of circ heater. Return hose on cab heat goes to a high point on motor. The instruction manual doesnt show this...

I have a MF 50 that the power steering has come apart on. The problem is that the power steering hydrolic cylinder has come loose. The pin that holders the ram in the anchor block has sheared. 1. I need to know the proper names for the pin and the anchor block. 2. Where is a good source...

My 65 MF 50 diesel will run for a few minutes and then shut down. It値l start back up after a while, but same issue. Any ideas?

I need a replacement for a Delco Remy model 1100424 alternator for my 65 MF 50. Any ideas?

Hydraulic question for plumbing a Shaver post driver to a MF50. Do I need any valves, or can I just hook up the hyd supply, unscrew the tranny fill plug, drop the return in that hole and start driving posts?

My dad owns this great little MF 50 tricycle tractor and I've been looking everywhere for information on it. Everything I have found thus far shows a 50 with four wheels and this one has three. Any ideas on where I can find out more on its value? I wanna say it's a 1969.

I hope someone can help on this. I know what its called, but the dimensions of my part are causing issues with replacing this work out part. The part is from my 1963ish MF50 high clearance tractor originally from Canada. It screws into the steering bellcrank on the hydraulic cylinder. All of...

I am new here. I am trying to find an aftermarket replacement fuel gauge that will work with my MF50 diesel. I purchased the sending unit from yesterdays tractors, but they did not have the gauge. does anyone know where to buy a gauge that will work? the part number I found is: 193950M91 Thank...

Hello, I have a 1959 MF50 that has seen better days. Recently I was using the rear blade on my driveway and the three point lift quit working. The front loader doesn't work either. If I actuate the valve I can see the three point move slightly but that's it. I'm a tractor idiot so any ideas...

After losing my 2014 Mahindra 4025 in a fire, I have recently bought a 1990's Massey Ferguson 231. I realize it has a small hydraulic pump, but it would save my back when splitting big logs. I already have the log splitter. I used it on the Mahindra. My 231 doesnt have any remotes. It seems to...

After losing my 2014 Mahindra 4025 in a fire, I have recently bought a 1990's Massey Ferguson 231. I realize it has a small hydraulic pump, but it would save my back when splitting big logs. I already have the log splitter. I used it on the Mahindra. My 231 doesnt have any remotes. It seems to...

Does anyone know how many CCA's the battery for an MF 50 with a Continental Z134 should have. It's a 1959 and my thinking is to get the highest CCA's I can. The battery that came with it is from Wal Mart, is 2 years old but only has enough to start it once in a while even after a night on the...

I have a Massey Ferguson 50 diesel and I am needing to add some transmission fluid is there some sort of level indicator for this.

We have an MF-50 in desperate need of new rear tires. What's on there now are 14.9-24 on 13" wide rims. They don't look correct so I thought about getting 13.6-24, but since we have a set of chains for plowing, should I be worried about how well the chains will fit, and how much traction might...

I removed the three point levers and when i reinstalled them my three point no longer works, can anyone tell me what happened and what i can do to repair it. If i need to pull the cover i will but hoping for an easier solution. thanks ron

I inherited a 1964 MF50. Although it ran fine... it looked really tired. So, I figured anything that is almost as old as me and still works deserves a some TLC... :laughing: It amazing what some new parts, fresh paint and some elbow grease can do. well one thing leads to another... I didn't...

I have just purchased an MF 50. The Stabilizer cylinders are leaking. I need to remove the bottom pin. I have attempted Blaster, hot wax, heat, gear pulley, 20 ton hydraulic jack and of course the old sledge hammer. nothing has moved the pin. Is it threaded??? or tapered??? Any answer...

completely rebuilding z134 engine. using I&T manual. engine had been rebuilt about 40 yrs ago by highschool class. The rocker shaft was badly worn. bought new one. Matched old one. When checked oil passages (rockerarm oil holes pointing to valve springs) the oil supply hole is on top of the...

Trying to restore a mf50 have rebuilt several cylinders on backhoe and now a new leak a constant drip at rear of the reservoir tank. There are 4 bolts that seem to run threw tank at Rear of reservoir and this is the area where its leaking. Does anyone know if there are Seals on these bolts or...

Just signed on ,I am overhauling my Hyd Pump on a MF50 any comment would be appreciated

Can someone tell me something about a 1960's area 50 series. I have a friend looking at buying one and he does't know much on them or is there a whole lot of info on one.

Good day, New member and new to me a Massey 50 with Allied loader. Just took delivery and parked it in the driveway. Loader worked perfectly when it was unloaded from the truck, parked for a few days and then when I started the tractor again the loader wouldn't function. 3 way RML-17 diverter...

Hi everyone my names phil currently living in Norfolk UK. I have a 1975 massey ferguson MF50 industrial front loader tractor which has not worked for 2yrs and now in the process of putting it back to work on the farm. The engine has just been stripped down and overhauled and the clutch system...

Hello Folks. New here. Nice forum! I have a question about how to properly operate the levers on my tractor. Picked up a 1957 Ferguson F40 back in December and have been slowly getting it into shape. Everything is great...except the lift wasn't working properly. It would only go up and down...

I was wondering what a good start price for an old Massey 50 tractor. It's the tractor only, been sitting a long time, for sure needs 1 rear tire. It's one of those......it was running great when we parked it kind of deals. I'm sure the engine is ok because I remember them using it to cut hay...

hi, new to forum here goes i have been told that you can replace the fan belt with some form of chain link belt as you dont need to remove everything?is it true, where do i get the stuff, what is it called and is it any good?

I have a massey 50 that was working well last time I used it. (about 3 wks ago) Now the clutch will not disengage. Any ideas? Thanks

I took lots of pictures when I disassembled the Z-134 in my MF-50, but I have a problem I did not document. I replaced the camshaft ( worn out) and the camshaft gear( worn out). The crank gear did not look too bad and did not want to come off. When I put the new cam gear on, everything was nice...

Hello everyone, I just purchased my first tractor and was wondering if someone was willing to help me. I bought a Massey Ferguson MF50 high crop model with an extra set of tires. The tires currently on the tractor are 12.5x38 and are pretty roached yet hold air, but the rims have calcium...

I am rebuilding a MF 50 with z 134 Engine. I have the rebuilding kit for the head, but there were no valve seals included. When I disassembled the valves, the valves had seals on them ( small 0 ring type.) It appears that they are not available in aftermarket, and some z-134 engines did not have...

My 1958 MF 50 ser# CGM519195 with z134 ser# 670808 is solid red with no gray or silver. I thought someone spray painted it red but inside the engine and bell housing are red. The valve cover has never had red on it and looks like a light gold or dark silver. The gas tank and under the hood are...

I have taken the timing cover off of my z134 getting it cleaned up to start rebuild. I had planned on replacing governor as a preventative part of the rebuild. Looking at it, it appears to be fine. No broken tabs or cracks. On the new governors you are supposed to put the shim behind it on the...

I am slowly aquiring the parts to totally rebuild my 1958 MF50 Hi-Arch with a Z-134 gas engine. I have removed everything from the transmission forward and am replacing every bushing, bearing, joint, etc. Even though I have not removed the timing cover to check it, I plan on just replacing the...

Any one know where to find parts for backhoe hydrolic can post pic if it would help Thanks for help

Tractor= 1961 Massey Ferguson MF50 High Row. I have read some previous posts by farmwithjunk about the ability to tie in a single acting cylinder (log splitter) into the MF50's internal pump WITHOUT having to buy the hydraulic diverter, etc.. that mounts in place of the cover plate below the...

I needed to finish my carborator before I was ready to get onto changing out spark plugs. It has been sitting for a year. I am going to change the oils and filters. Flush the radiator. But is there any pressing items that can come up. I just want to get her running. I have to change out the...

Hey guys, first post so I figured I'd start with my new to me MF50. Actually lets back up a couple years and really get started. (wall of text warning) A couple years ago my buddy gave me a '55 To-35 with a Davis 102-A loader. The tractor was missing it's hood and had had a backhoe installed...

My MF 50 has a very low speed 1st. gear ,almost a creeper. This is great for running PTO at high rpm especially using a flail-mower in the very high grass this wet summer gave us. My question is: I only have one sway bar connection to the read axle. Can I safely operate a flail mower without...

Hello, I'm the new proud owner of Massey Ferguson 50, not sure what year - what I thought was the serial number isn't close to what is on Tractordata.com, so I'm not sure I have the right number. Anyway - it's my first tractor, and seems to be in decent shape, but will need some work. My first...

Hi Guys Great site, i just bought a MF tractor to restore and to do all the landscaping we need to do on our new build etc. I HAVE searched for 3 nights trying to find the correct ident for this machine and have found a few conflicting answers so here are the pictures of the numbers i have found...

Wanted to find it who has personally made this repair and what were some of the difficulties or issues you came across. I'm thinking about buying an MF50 that needs a new rear main seal (where the engine meets the trans) and am curious what I'm getting myself into. It seems fairly straight...

Got a 1958 Massey Ferguson MF50 that we bought from the guy across the road. He said he had the air filter in the basement and that he'd get it to us, but he never did, then his house burned down.... Can't find an air cleaner assembly. The YTmag store doesn't have one for the gas engine for the...

I went to look at a MF 50 tonight. Gas engine and he stored it outside. There was snow/sleet coming down and I didnt see any evidence he had gone out and started it prior to me getting there(good thing). So he pulls the choke and it fires right up. I was thinking thats a good sign. The...

I just bought a Massey 50 diesel and can anybody describe the manifold pre-heater? Here in the U.P. of Michigan in the winter I'm having to plug it in to start it and the preheater off the key switch is not working. Looking for a drawing or schematic of the pre-heater to repair or replace.

I need to change the oil in the Tansmission,Differential and hydraulic system of my MF50. The manual calls for straight mineral oil. Can I buy that if so where or what is the accepatable substitute for it. Thank you

I just bought a MF-50 a few days ago and was in the process of changing all the fluids, after draining the hydraulic fluid, I decided to look in the bottom case where the pump is located and noticed two 3/8"x1 1/2" bolts and lock washers. I also found a tapper pin that is about 1/2"x1 1/2". I...

How do you clean a air filter on a 1966 MF 50?

new guy from canada...had tractors since i was born...my father used to drive me to sleep in the fields before i could talk..looking for help figuring out wether my tractor is either a 50a 50b or something else..i know its a massey ferguson industrial tractor with a bucket on the front ..i'm...

Hello! My husband and I are working on our (new to us!) Massey Ferguson 50. It's a gas powered 2-wheel drive. It starts but has no power. A new starter has been installed and the carbuerator was rebuilt by a friend. We NEED this cool ol tractor to run properly!! Any ideas, folks? Ya'll are all...

Howdy, We bought a small horse farm not long ago. The previous owner left a 1964 MF50 tractor. It's in great shape and runs fine, but i know nothing about about tractors. It has a throttle lever on the steering column!. Here are my questions: When I pull the throttle down to full open it...

Hi, we have a used MF135 that we were trying to age. I was told serial numbers 117429-141425 were 1969 is this true? We also have a MF50 loader that we think is a 1970 J reg? Can anyone help? Thanks

looking for a wiring diagram for a 1961 massey ferguson 50 three cylinder diesle someone put a alternator off of a GM truck and messed up the wiring.and how much boost can you push with a turbo without working on that engine.

where does the inner seal go on the rear end.im 14 years old and restoring my first tractor to use on the farm and need a little help

I have an old Massey Ferguson 50. It is in peices. My dad is trying to restor it and we need some advise and some parts. the tractor ran well for the first 10 years I had it but needed lots of work and was leaking water into the oil, I think. I am looking for a front grill or the kind of...

Found spec sheet for your injection pump 3340F000, has 3 possible fuel setting codes, 49/900/3/2310, 52/900/3/2310, or 57/900/3/2310. At your altitude I hope code on your tag is 49 or 52, I know 57 will probably have some smoke. Here where I am in IN about 900 ft some MF tractors are OK with 63...

I have just bought a MF50 and I havent aquired a service manual yet but i am looking for a quick answer. This tractor doesnt have hydrauilics out the back and I would like to run a cylinder. Is there somwthing I can buy to make this happen rather easy? Thanks

:thumbsup:

Hi I'm looking at my first tractor. I've found an MF 35 deluxe with a gas motor in excellent all original condition, with basically all four tires new. I'm comparing it to a MF 35 Perkins diesel in good to very good condition with some rust on the fenders and the tool box completely rusted out...

Hello all, First post...thanks in advance to anyone/everyone for their help! I'm a bit of a tractor idiot, so please bear with me... I bought an old MF-50 last spring. So far I have started it up twice this winter (Michigan) with no problems. Last time was about two weeks ago. Just today I...

A friend and I have been trying to get our MF-50 (gas) running after sitting for a year or two. It ran pretty well when we parked it, but now it won't even sputter when cranking. We noticed that the distributor is loose; it rotates pretty easily (but not quite freely). There seems to be a clamp...

Does any one have service and repair information on a MF 50 front end loader tractor

I need, NEED to get one remote to the back of my Massey 50... Its time to cut hay and my sickle mower keeps breaking down, my neighbour loaned me his haybine but I have no way to lift it at the moment. Can I run a hose from the adaptor plate on my rear end to a quick connect, so that it will...

Does anyone out there have a source for a used or new rim for a 1968 MF 50 Industrial? I haven't been able to find a match. The interior of the rim is clean with the exception of two anti rotation pins. The rim attaches to the hub with clips. Any advice is appreciated.

My brother has a MF50. His transmission is "stuck" in first gear, the hi-lo works but he cannot get it out of 1st into any other gear. He changed the transmission fluid he said about 1 year ago, the manual said 27 quarts so that is what he put in. He says the manual does not show a dip...

While mowing my MF 50 locked up on the road ,tried every gear tractor would not move (rear wheels didnt turn)had to pull off road with the pick up as iwas pulling it in neutral the left rear wheel turned forwards and the right rear wheel turned back wards no grinding noises present, but I am...

Hi, I have a 1958 Massey MF50 which I am considering selling. It runs well, the valves have been adjusted, the entire ignition from coil to spark plugs is new, it also has all new fluids. The carburetor has been completely rebuilt, the starter has a new bendix drive and the engine has a new belt...

hay... im wont to start to fix my MF50 and i need this book. someone know were i cen buy the repiar manual ???

I have a Massey Ferguson 50 with the 3 cyl. Perkins Diesel. It was rolled over by my father about a 2 years ago. The tractor still runs and will move under its own power. Due to my fathers being killed when the tractor rolled we are going to sell the tractor along with the other farm related...

I have a Massey Ferguson 50 with the 3 cyl. Perkins Diesel. It was rolled over by my father about a 2 years ago. The tractor still runs and will move under its own power. Due to my fathers being killed when the tractor rolled we are going to sell the tractor along with the other farm related...

Hi,I'm new here,from Trinidad in the Caribbean,I'm a heavy equipment and general contractor,I own a couple pieces of equipment,including excavators,backhoes etc. I recently took an old MF-50 backhoe off a guy's hands .I was really trying to keep away from such an old piece of equipment,but...

Hey all, I was just outside putting the blade on my old MF 50, when I lifted the blade and put it in gear to plow the driveway I let the clutch out and BANG. That was it. No movement. The hydraulics and PTO still work. I'm thinking it's the rear driveshaft but I don't really know. Any...

My MF 50 has started to have problems starting. I just get a clicking sound when the key is turned. Tho only way to start the tractor is to turn the key and jump the solenoid. When I started to investigate the problem I found a fuse on the battery side of the firewall. When I opened up the...

Just got a MF 50 with a MF 100 loader. The problem is when I go to lift either the bucket or the whole loader, it goes down until I get the lever back a little bit. The problem is doing any kind of precise work with the loader gets a little dangerous if it won't go up right when you tell it to...

Doing a restoration on my 1962 MF 50 and am having difficulty with the disassembly. Specifically, I can't get the steering wheel off. I have the service manuals and they show the retaining nut and washer. After that, it looks like it should just pull off of the shaft with a little help from a...

Hi There Can anyone tell me if this is an MF50 and roughly what year it is or might be?? Thanks Cheers Ian

Hello Just wondering if anyone knows what year and modelthis tractor is? Thanks Ian

I am replacing both inner and outer seals on my MF50, aprox 1957 vintage. It appears to me that the inner seal keeps the oil from the bearing, so can anyone tell me if the axel bearing is lubricated by packing with grease? That is all that makes sense to me, as the packed grease is held in by...

Thinking of buying this one but here's the story... Industrial (yellow) MF50 w/ loader and PTO. Seller says he bought it at an auction. He first noticed one injector line was brazed shut so he replaced that. I guess the auctioneers did that cause it was cracked and they wanted to run the tractor...

I bought a backhoe and am told it is a mf50, possibly 1975. I do have a couple of issues with that someone out there may be able to help with. First of all it is a devil of a thing to steer, and when stopped can turn steering wheel and wheels do not turn until I'm moving and then constantly...

Hey guys I am new to the site. I just purchased a 1962 Massey Ferguson 50. It needed some work to get it running. Once I got it home I got it running by priming the injector pump. Then I changed all the fluids and all the hoses. I ran it around the yard and fields. The multipower linkage was...

would anyone have access to an upper link / top link / rocker ,for my massey mf-50 industrial machine? #s on the link are 1883 391 M2. #s in the parts book show 1886695 M92 called a beam assembly. control. IF YOU THINK YOU MAY HAVE, I CAN SEND YOU PICTURES OF PART. thanks , nysumrwind

Hi, I have a MF 50 and I'm instaling a new clutch. But I can't find any specifications to make a tool to adjust the three main plate fingers. Does anybody have the specs? Also the manual says that there is a spacer on the end of the input shaft. But I can't find a part number for it and I...

Hello, I'm wondering what kind of battery a 1958 MF 50 takes. It has the Z-134 engine. I'm not sure if the battery that came with it is the type it's supposed to have or not. Thanks! :)

I have a MF 50 a Tractor Backhoe loader the engine has?? over 4000 hours, runs good. Bought with no mechanical history. What can I expect to get life-wise out of this engine before a overhaul? Leaks out if the front crank seal, replaced two years ago, leaks again. Other then that runs...

Hi I have MF50 Gas tractor. Starter motor spins but bendix does not engage. Starter is a Wilson rebuild Delco 1107226. I took the starter out and dont see anything broken but havent pulled it apart yet. If I hold the starter vertically with the bendix end of it downward the gear slides to the...

Hi, I was running my tractor yesterday when it started to make a clacking noise. So I started checking different things and found one cracked cylinder liner. How hard is it to replace and should I go ahead and rebuild the hole engine? Considering it's age, it seems like it might be worthwhile...

Hey y'all, I have a ,57 MF 50 that I would like to put a FEL on (assuming that one can be mounted). Can anyone steer me in the right direction how to go about finding one? Thanks, WW

I just bought this unit. Like it a lot, but found it had a broken collar on the L-R shaft that moves the boom. Any ideas where I might find a replacement part? Thanks, Jim

Hi, I'm new to owning a tractor and new to TBN. Anyways I just bought a 1962 Massey ferguson 50 diesel. It runs great and looks OK. I paid 3000, does that seem like a good price? It does have a fairly new injection pump and the the rear tires are in very good shape, it does need one front tire...

Can anyone tell me what fluid is used in a shuttle shift tractor? Some say auto transmission fluid and others say a very expensive case lube at 140.oo for 5 gal. pail Can you use some aftermarket oil? Thanks for your time, Terry T

I have no clue about this tractor only that it followed me home last week. You know the deal that is too good to be true. Anyways my problem is "what is it?" and what is the fluid that it used for the "shuttle shift?" I was told reg. trans fluid? and for the perkins 4 cylinder engine, what...

I am looking into a tractor down the road from me and was wondering what anyone knew about it? I think its a masey 50. with ford 8n fenders. i found this on it. <MHP> 182 840 M2 Anyone know what year it might be?? Thanks for any help --taylor It comes with the Hog...

I am new to this discussion group but I have been going to tractor shows in my area of East Tennessee (Powell, Knox County) for a while hoping to some day buy an older tractor to help take care of my 5 acres as well as to have something for my sons and me to do together. I have been checking...

Hey y'all, I'm definitely a newbie to the tractor thing. I recently bought a used '57 MF50 (34HP Continental gas) and was wanting to purchase a 12" turning or moldboard plow (either a 2 or 3) but didn't know if I had enough tractor to pull the 3. What do y'all think? Thanks in advance, WW

I have a MF 50 that I'm trying to get running right. I took the air cleaner off and it is a mess. So the Questions. Is there a way take the air cleaner apart in order to clean it? If you can't take it apart how/what do you use to clean it? If you can't clean it, Do you have to replace the...

I've got a MF50 Industrial TBL (Perkins AD4.203) and the clutch won't disengage. I can feel what I think is normal clutch pressure on the pedal. Between the shuttle shift lever, L-H range lever, and gear shift lever, I can get any 2 into position but not the 3rd, all the 3rd lever does is grind...

ive just purchased a old mf50 backhoe and loader.the diff oil is white and needs changing. im seeking advice where the filler plug is .i will also change torqe convertor oil. i asume the filler plug for this is on the side .any info would be appreciated . thanks

Good afternoon everyone. I just picked up An MF 50 and noticed the 3ph would drop to the ground fast with the engine off. That didn't bother me too much,but after using a bushog for an afternoon I noticed that from time to time the bushog would drop completely down and make a better plow than a...

I am now looking at a nice old MF50 (1962 model year I believe). Any input on this model would be appreciated. Very clean tractor. Thanks

I was plowing and I cracked my hydrolic and transmission case under the seat. It was welded at some point in its life. But it went down today. It's to far gone to reweld and I don't wnat to chase the weld. 3 point stopped working but the axles still go. Anyone know a good place to order a used...

I just purchased a MF50 with loader and backhoe; the hydraulics on both of them run off of a PTO mounted pump. The 3pt. hitch lift arms do not work; they do not seem to be connected in any way to the loader/backhoe hydraulics. Do the 3pt. lift arms run from an internal pump ? Moving the...

I have a 56 and it is the funnest tractor that I have ever owned. I still love the power of my SMTA but it is too large for 6 acres. I enjoy its power but don't need that much engine. I only wish that I had a FEL for the MF. But I use my rear bucket to move dirt. I have been told that a FEL of...

Looking for a loader for my MF-50 unit. Any help would be appriciated.....

massey-ML-554501-ML- Brand specific. Moved to the Massey forum.

1962 MF 50 w/loader and scraper. Leaks a little hydro fluid, but other than that is pretty tight. Around $3500

1962 MF 50 w/loader and scraper. Leaks a little hydro fluid, but other than that is pretty tight. Around $3500

A fellow I know has one and he bought a new oil filter for the transmission-differental but can't figure out where the filter is located. I told him I would ask around and try to find out. Thanks for any help. Michael

Problem: The drift feature was stuck in the upright position but would move the 3 point up or down with no inbetween, and the position level lever moved but the 3 point would not move up or down. I opened the tractor and fixed the drift portion but now I have no hydraulics, the tube that comes...

I have been browsing TBN for a while now, but this is my first post. I know a guy who deals in used tractors and parts who has a MF 50 Diesel that runs great with no leaks and good tires. He is asking $3500 for it including a used bush hog. Does this seem reasonable. ALso I don't know a lot...

Anyone looking for a nice old(er) tractor for working or to fix up for show in the MD area?

Any idea of what a good price would be? Suppose to be a 92 model, but looks older. The backhoe stabilizer arms go straight down versus extended out at a angle. Seems this would not give stability when using the hoe? Anyone had any experience?--Ken Sweet Sweet Farm Equipment Co.

well i just bought a massey 50 xh backhoe,extendahoe with a 4 way front bucket.any ideas where i can get service manuals and parts manuals for it? thanks! jiminpa2@yahoo.com