kubota b3000

Have a Kubota b3000 would like to do away with belly mower and go with a three point hitch finishing mower I think Land pride is what I'm looking for but I've not seen anybody use the rear discharge sometimes I mow grass that's only cutting two or three inches other times I'm mowing six or eight...

I parked my 2004 Mazda B3000 V6 3.0 at 83,000 miles in 2017 because I had other vehicles and there's been a safety recall on the airbags. The airbag parts are supposed to be available now, and I'm getting it ready to drive again. I'm not seeing any evidence of the original water pump leaking...

I would really like to get away from the regen position as the first function on the bucket dump portion of the loader valve. I see that the B3030 and possibly the B3000 use a loader valve that physically looks like it could fit but not sure if it functions any differently than what I have now...

Hi All. I have a B3000 and when I pulled it out of the garage, I noticed a small pool of oil on the garage floor which was right where my front left wheel was located. I looked a little closer to the wheel and saw that on the inside of the front left wheel was a bunch of oily dirt on the rim...

Hi All. I want to get at the HVAC mechanicals on my B3000 that are located in the roof area. Has anyone removed their roof of a B3000 or B3030? Can I unbolt it without completely removing the "Inner" roof/headliner? I think there are only 4 bolts that need to be removed from the inside to...

Posted in wrong section.

The B3030 and B3000 are nearly identical tractors. The B3030 had side glass windows that opened (although not a lot), but the B3000 has stationary side glass. Has anyone with a B3000 ever tried changing out the windows on the B3000 to allow them to open like the 3030? Pricing out the side...

Hi All. MY A/C isn't getting as cold as it used to and I took a look at the sight glass and saw it started out with a very bubbly stream and then went to clear, as in no fluid as far as I can see. I have ordered some cans of 134A Freon and a decent set of manifold gauges. But, once I get it...

HI All. I have a B3000 and am in the process of installing some LD worklights. The OEM Halogen lights were 55 watts each, which should be about 4.5 amps x2 = 9 AMPS The new lights I am replacing them with draw 6.3 Amps each x2 = 12.6 AMPS. My question is: What is the wire gauge running to...

Hi All. I have a B3000 HSDCC and I went to use the Rear "Washer" yesterday, and no juice came out. The Washer Fluid reservoir is full, and the front washer works fine. I tried holding the switch down a good long while to see if it had to "prime", but no luck. Any suggestions on what to look...

just installed a product called boom mat inside my cab and WOW! this stuff really works, pulled the seat and did the whole pan, floors, and under the hood! its nice to work with plus has good thermal value! check it out!!!!!!!!!!!!!!!:cool2:

Hi All ! Has anyone with a B3000 or B3030 replaced the OEM Headlight bulb with a LED bulb? I don't know the exact bulb number of the OEM Bulb, but hope someone has replaced theirs already. THANKS !

So the 5 amp OPC fuse seems to be blowing more often than not. This only happens when tractor comes to an abrupt stop. This could be hitting snow bank, pile of dirt. And it is similar to if it were to stall due to engine overload, but the fuse blows. I have made the tractor stall from engine...

Hi All. I have a B3000HSDCC with a set of OEM work lights on the front and the back. I want to swap them out with LED work lights but want to know if the light switch circuits have a "Relay" already or not. I suspect they may, but don't know. Each set of work lights is (I'm Just guessing)...

Does anyone know if the PTO shaft diameter is the same size for the Rear & Mid PTO shafts on a B3000? I wanted to buy a Shaft "Cap" to go onto the Mid PTO Shaft to protect it like the cover on the Rear PTO Shaft. The Kubota Part number is 31220-25820. I read somewhere that they are not the...

Hi All. I just got my used B3000 HSDCC delivered this week and was playing around with the heat controls. I noticed that the air stream is pretty strong and its nice and warm... EXCEPT... for the right side vent. It seems to be blowing cold air instead of warm air like the rest of the vents...

How does this price sound? B3000HSDCC, 300 Hours, FEL, Belly Mower, Front Snow Blower. Appears to be in pretty good condition. $26,500.00 Gunna run about $1,000 to have it transported to my location. Thank for the input. Or I can get a brand new B2650 w/belly mower, FEL for $27,700 PLUS 6%...

UPDATE 4/15/2022: Well, after 4 years running without the backhoe frame extensions, I decided it was time to add them back in. The cramped platform and tiny seat just became too uncomfortable for me to deal with as I get older. The ONLY benefit to moving the backhoe closer to the cab was the...

Added front and rear 27 w LED work lights. 2600 lumens from each really brightens up the work area now. Also added cab level caution/turn signal lights to increase my visibilty to other vehicles when I'm on the road. Wanted a 12 v power outlet for use in the cab so I found one that had USB...

Ok, I'm stumped. Last weekend, after running my flail mower for a couple hours, my loader boom stopped being able to raise after I finished mowing. All other functions are working fine - loader boom lower under power, bucket curl & dump. When mowing, I do have to raise & lower the loader...

I am thinking of adding a second rear hydraulic remote to my B3030. I would be ordering the Kubota-made remote kit and float detent valve which stacks onto the base remote valve. The Kubota wholegoods part numbers are B7307 for the second lever kit and B7305 for the second valve. My question...

I am searching for the rear hydraulic remote kits for my B3000HSDCC and I have found the valve section kit part# B7304 but cant seem to find the other kit part# B7306 Which is the control lever and mounting kit. I have called my local dealer where I purchased the tractor and they said that they...

Hi all, I wanted your opinions on this WSM for my 2011 B3000. 2011 Kubota B3000 Tractor Service Workshop Manual | eBay Thanks much, My Hoe

Hi folks, I remember reading, back when I was hunting a B3030, that Kubota makes 1.5" (aluminum?) rear wheel spacers, to widen the track a total of 3", for added stability--especially appreciated on slopes and with cabbed tractors/hoes, etc..., due to their higher centers of gravity. But I...

Hi all, I know "Search" is my friend, but unfortunately, right now, Time is not--LOL. So I wanted to ask if a few people could direct me to their favorite "Things to Check Out When Buying a Used Tractor" CHECKLISTS, ideally. Or to threads, if no such Checklists exist. I'm looking at a...

Hi all, I'm looking at a 2011 B3000, that already has the "3RD FUNCTION VALVE KIT FOR CAB $799.00" and " HYDRAULIC ANGULATION KIT $483.00," to operate the hydraulic angle, factory snow plow. Is this "3RD FUNCTION VALVE KIT FOR CAB $799.00" and " HYDRAULIC ANGULATION KIT $483.00," the same...

Hey to the Brain Trust, And older friend of mine (since moved away) has a B3000 (I forget the year, but it's like 2011, I think?) and he called me, because it's making what he feels is a strange noise. (EDIT: Title should read "Clacking Noise..." not "Clunking Noise...." Sorry). He said it...

Hi all, I'm confused. I would like to know the difference(s), if any, between the last of the B3030HSDCC's "Premier Plus B Series" and the B3000HSDCC "Premier Plus B Series." I've been seeking a late model, low-hour B3030HDCC. It is my understanding that the first "C" denotes the "Cold Cab"...

I'm somewhat new at tractors and hydraulics so perhaps this is a dumb question, but if I wanted to add a hydraulic top link and also upgrade to a hydraulic rear blade on my Kubota B3000, wouldn't it be a simple matter of re-plumbing a couple wyes into my existing rear remotes? I figure if I...

I would like to buy a rear mounted wiper kit for my B3030 HSC. I went to my local Kubota Dealer and they priced the kit at $400.00 installed. I told them I wanted to install it myself and they then said $310.00 for the kit only. I told them to forget it. I have spent a couple of hours...

any veterns out there know how to dampin the hst noise in my cab? i know it all probably starts in the floor, but what to put in there that will be a sure improvement? any help would be great! thx

Just looking for opinions on which cab tractor to buy. Seem to be almost the same, one question I have is what is the diff between Hydostatic power steering and reg power steering, and which is better??? Are the breaks on the left (2650) that important. Is the 2650 not as loud? For now...

I am looking at converting my new B3000 with 12.4-16 R-1's with 10" rims to a narrow setup. Tire dealer says 9.5-20 on a 7 or 8" wheel with 1.5" offset will = proper gear ratio and narrow it up a bunch. Will need to have custom wheels made, big bunch of Dollars. Any ideas on other Kubota...

Just got a new B3000 cab, all options except the radio. Would like to install a radio, not as loud as I hear it would be, looks like it has the wiring harness and antena hookup behind the little black plug in the headliner. I am sure this question has been asked before, but can't find link...

Could anybody please advise me on meaningful differences between these two models? I am considering buying a used B3030 with cab that is currently available but I noticed on the current thread re cab noise in the B3030 that someone said that this problem had been improved on in the B3000. I...

Could anybody please advise me on meaningful differences between these two models? I am considering buying a used B3030 with cab that is currently available but I noticed on the current thread re cab noise in the B3030 that someone said that this problem had been improved on in the B3000. I...

does anyone know where i can find a seat cover for my b3000? jumped in the other day with a screwdriver in my back pocket F!?@%#!

should i renew or not? just want advise on the subject, dont know the cost!

Want to buy a Kubota B3000 hstcc, but it is too wide for needed purpose. Need to find rear tire and rim setup. Factory options don't work. Factory setup gets me to 53+inches, need to get below 50". Any ideas? Have heard that 8.3-24 R-1 will work rather than the factory 12.4-16 R-1?

ok here we go! i had about 2hrs. into it and i like to think that it went great but i would also like to tell kubota that digging into your head liner is bulls!@?! there i got that off my chest, anyway i was pressed for time when i was doing it which didnt help because of a dentist appiontment...

I have a new Kubota B3000 CAB and it blows white smoke and chuggs for the first 15 seconds after starting. Any ideas?

Hi all, Haven't posted in a long time but i am a long time member. Just traded in my BX2200 for a B3000HSDCC. I live in NH. Most of my seat time comes in the winter - hauling firewood and plowing snow. My wife insisted we get a cab tractor to keep me warm. Here are a few pics. This is on the...

My new B3000 TLB showed up midday today. Thanks to Brady Barlow and to Marvin, his driver, for their excellent service. This is my second purchase from Barlow Equipment, and both transactions have been enjoyable. I expect I'll be very happy with the new machine if it measures up, quality...

When I bought my B3030 in 2008, I thought I was "man" enough to survive on an open station machine for many years. But low and behold, during the long, cold, snowy winters, I'd find myself daydreaming of clearing snow in a nice warm cab without having to be bundled up in bulky winter wear...

My AC switch crapped out and Kubota sent me a new one. I hoped I could take the face plate off the headliner and get at it but no luck. The service guy at the shop said I may have to pop the canopy off, but it was only 4 bolts. Anyone know how to access the back of the climate control panel?

In my tractor research (considering a B3200) I've read a bunch of posts about engine vibration with the 4 cyl engines. Several people indicated that the timing was set differently at the factory to meet emissions requirements and when correctly set the vibration was no longer a problem. All of...

I was eyeballing a new B3000 at the local dealer this morning, interested in hearing from anyone who owns one and likes dislikes. I plan to use it on 5acres for mowing, post holes, trenching (with BH option) tree planting, snow plowing, back filling etc. Not heavy work but standing next to it...

been reading about cab noise with b3030 and b3000 cabs. Not 100 percent sure of the series tractors to be honest by i know that the noise seems to be coming from the hydro trans. Have you guys ever thought of using a sound deadening material like dynamat? Use 2 or 3 layers of that stuff on the...

Has anyone checked out or purchased the new b3000 cab? Wondering if it's any quieter and tighter sealed from outside dust? Mine has 653 hrs on it now with only a worn out cutting edge and with all that Wax build up, I may be thinking of going new if there's a large enough improvement in the...

Have never had this problem on a kubota. When trying to reinstall my FEL today (loader has sat for about 2 months on its stands) white and yellow QD fittings will not install. I think white/yellow are main pistons, blue/red are bucket tilt. Tilt works fine when tractor is running, grapple...

have a hydraulic spray pump connected to one of my remotes. It works perfect. The problem is that while the spray pump is running, my 3 point hitch will not go up or down. Is there a fix for this? I can't use the pump and operate my hitch at the same time. What gives? Thanks

I have a hydraulic spray pump connected to one of my remotes. It works perfect. The problem is that while the spray pump is running, my 3 point hitch will not go up or down. Is there a fix for this? I can't use the pump and operate my hitch at the same time. What gives?

Hi. How many have gone shoping for a new B3000HSDCC yet ? I'm trying to get a feel for pricing. I have a B2150 with FEL & Belly mower to trade. I'd be looking for a B3000HSDCC with FEL & 60" Belly mower. Rear Work Lights, Radio/CD etc. What type of pricing/quotes have you all been getting...

hey got a new 1260 land pride box blade and it is awsome in the snow!!! got 2in. of snow today so i got to play alittle! it cleans the asphalt so nice behind the 72in. scoopdogg snowpusher, plus it works really well in reverse pushing snow!!! i know what u veterans r thinking, ya da we already...

I am looking for information on where kubota hooked the cab heater hoses on these tractors. I am installing a heater on my b3200 and bought a kit but it requires you to cut the radiator hoses and insert adapters. I am not real fond of this. I would think the cab tractors should have a similar...

hey my cab keeps fogging up, got the fresh air open, let it warm up, any advise would be great! thx

Hi everyone, I'm new to TBN. I've been watching the Kubota forum for maybe a couple of months researching and studying before I " pulled the trigger," trying to talk myself out of spending so much for a 'lawnmower." I think I was really justifying or convincing myself that it made sense to...

Hi everyone, I'm new to TBN. I've been watching the Kubota forum for maybe a couple of months researching and studying before I " pulled the trigger," trying to talk myself out of spending so much for a 'lawnmower." I think I was really justifying or convincing myself that it made sense to...

got pics of new 72inch scoopdogg snow pusher! it works great:thumbsup::thumbsup:

Hello, I posted my introduction over in the new members section. I just purchased a new Kubota B3000 with an LA403 FEL and R4 tires mainly to tame my 12 acres. Most of the property is fescue but there are some hills. The dealer loaded the rear tires since I have some steep places on my...

This is my first winter with this tractor. I bought the kubota QA with the 72" Kubota blade, all hydraulic angling. My question is, should I have my 500# rear ballast on when I snow plow, or will that work against me? I have R4 tires. I have skid shoes on it for my long gravel driveway to the...

Hey guys. It doesn't say in the manual how to do this for some reason, but I think you just reposition the link stops or something on those lines. The mower is off but I want to keep the links on and not have them raise and lower with the 3pt hitch activation. Does anyone have any advice or...

hey, just got a new scoopdogg snowpusher, 72inch,for fel. its built like a tank, cant wait to try it, will post pics soon!:thumbsup: btw, centralparts.com kicked everyone on price! thx tony

Hi all, I have heard two different things from two dealers: one says with the Kubota 63" front-mounted blower (B2782A) subframe, even with the blower itself removed, the loader cannot be used, and the full subframe has to be removed to allow the loader to be remounted. He says it takes about...

one dealer says no problem for a 5', other dealer says 5' too heavy. Anyone with experience running a 5' brush mower on the back of a B with any issues? Thanks

Ive read that the wheel spacer kit on a B3000 with the 72" mower is a no go because of interference. Is this true? Also, will the 60" deck work with wheel spacers? Im assuming the wheel spacer kit is for the back only, but is there one for the front. Is that even a good idea. Ive seen...

At the Kubota dealership I was attracted to a B3000CAB. Very nice tractor and a pretty amazing cab. I also saw a B3030HSDC. To me these two tractors seem identical. When I came home I went on the Kubota website to look up the specs of these two tractors. The specs also suggest that these two...

here they are finally the new b3000:confused2::drool::laughing::licking::thumbsup:

wow it is here!!!:licking::D the new b3000 got delivered last night, it is super nice!!!! i need info on how to post pics????? can anyone tell me how to do so, thx tony:thumbsup:

Hi Everyone, I presently have a BX 25 that I am trading in on a B3000, my property is very steep and has been a challenge with the BX 25, I have many times used the weight of the backhoe to make turns by reaching back and turning backhoe uphill in order to keep from tipping. I do not think I...

hi guys, went to the dealer to see my new tractor its not ready yet but will post pics soon!

hey guys, does anyone have a new b3000, i found out today that i cant have mine till june because the turf tires are on back order. this really bums me out!!!!!!!!!!