ford-new holland 2120

Be gentle please, but I am at a loss. The starter quit on me while trying to bleed the fuel system, I know.. Anyway, I ordered a new one and it seems as though it is turning the engine the wrong way? It sounds completely different turning over, and I heard a click every revolution on what...

Afternoon everyone, I have a 1996 Ford NH 2120, under 900 hours, starts right up, runs good, has plenty of power. The other day I was grading my driveway and had stopped to pickup some rocks. When I got back on, I happened to look down on the right side on the ground and saw a small puddle...

I have a 2000 NH 2120 with a 7309 front loader. The right lift cylinder is leaking and I would like to install the new seal kit. But I can not budge the cylinder head (end cap) at all! A couple of questions: 1. What is the correct direction to spin the end cap? By looking at the retainer...

Troubleshooting main/loader hydraulics on 2120. Pressure should be around 2500. Did pressure test with gauge and pressure shoots up to about 2000 for a second, and then settles down to 1200 after 2-3 seconds. What would cause this? Weak pump, or internal leak in one of the cylinders or in the...

Hi , We are doing maintenance on a NH 2120 compact tractor with a NH 7309 front end loader. There are a bunch of hydraulic hose quick couplers and most are leaking. I looked at the videos about removing/replacing the internal O-ring on the one side to stop the leaking. Then looked up the...

My 1997 New Holland 2120 was in shop May to last weekend and while mowing I forgot I cut a tree down last Fall, and with grasses so high I hit and rolled over the stump. I was hung up on it a bit on the front end but got off and everything looked OK so I continued cutting. I then noticed my Tach...

I have a 1997 New Holland 2120 that’s not engaging the pto. It is shuttle shift and I can’t turn the pto shaft counter clockwise it only will go clockwise so I think the one way clutch should be good? The clutch in the tractor seems like it’s engaging good with no slipping if anyone has...

I am trying to add a two spool valve to enable rear hydraulics for a hydraulic top link and hydraulic leveler/tilt on a Ford/New Holland 2120. The two spool valve(s) I have are mounted on a plate with 3 ports... IN, OUT and PB. My tractor has a front end loader valve with 7 hoses - 4 smaller...

This machine has about 2700 hours of rough use by previous owner. I changed fluids and filters when I got it. The hydraulics are sluggish and jerky. The replacement filter I bought online showed up and was far smaller than the factory installed filter. I would like to know what filter might...

I have a 1990s era NH2120 with HSS. I can't get the HSS into 3rd or 4th in any of the 3 mechanical gears. Everything else works fine, I just can't move the shift lever into 3rd or 4th with the normal amount of force. Or even a little more than normal. Any ideas what might be wrong or where I...

I have a 1995 ford 2120 with about 2800 hours. I bought it earlier this year and just changed the hydraulic oil and filter about 50 hours ago. Problem I am having. The loader and rear lift quit. I waited about half an hour and tried it again. Now the loader moves slowly up and jerks as it’s...

Hi , Recently Ford NH 2120 (mfg 1990) started this chattering noise whenever it’s put into 4wd . The noise seems to be coming from the front of the front transmission where the driveshaft to the front axle goes in. At this point I’m clueless as to the cause but imagine it some sort of...

Hey guys. I bought a Ford 2120 that I will be fixing up. Was wondering if you could confirm year for me. Serial number is UV21865. I believe it to be a 1988, but want to be sure I have it correct. Thank you.

I have just purchased a Ford 2120 tractor and have been looking at loaders for it. The loader that Ford put on it was really beefy, (7109, later 7309) Has about a 2400lb lift capacity at the pin. Quote from Westendorf was $7400+ freight. Anybody have any suggestions? I am looking into...

Good Morning, I have had a steady leak of antifreeze that seems to find its way to the engine block plug and then drips form there. I am not sure what is wrong. Attached is a picture that I think is the casue of the leak. Would like any input on what you think I should look at or do? I have...

I am looking for a used backhoe for my 2120. I believe it is a Ford/New Holland 758B. Anybody out there with one for sale?

Hey guys I have a 1989 Ford 2120 and I lost reverse it starts to roll backwards like a foot then stops and goes nowhere it travels fine forwards any idea where to start looking it’s my first tractor that wasn’t just a lawnmower so any help would be much appreciated

I’m working on a 2120 HSS and the transmission dipstick has machine marks in it from contact with a shaft/gear. The dipstick is not bent do I’m asking if this is an occasional issue or a sign of impending disaster. Transmission operates fine. Thanks 90cummins

Have a NH 2120 with the T854 Shibaura engine. Block is cracked near a freeze plug. Have had it in the shop for several attempts to weld it but without success. Thinking I need to replace the block. Networking here in hopes of finding a lead on a half block or engine without breaking the bank...

Hi everybody. I broke the right front wheel of my tractor. I need some parts, used or new. I need the cover and the bevel gear housing for that wheel. I thank you in advance for your help. If you can tell me where I can find the parts that I need, it would be great.

I am having intermittent issues with my tractor moving. It will be moving along fine and then all of a sudden stop. My hydraulics will still work but I will not be able to move. It is almost like the hydraulics are cut off to the drivetrain. Sometimes its a quick pause, most of the time I...

I have a 2001 Ford/New Holland 2120 with EHSS that is giving me intermittent neutral problems. I have traced all the wiring and came across a mysterious small black plastic box that is in between the shuttle shifting switch and the EHSS controller box. I can not find this box on any schematic...

Hi all, Im a little confused on the clutch operation of my tractor, it has a shuttle shift and a single clutch, it has a cable from the clutch pedal to the lube valve, I have the service repair shop manual and the owners manual on it, still do not understand how the clutch operates, is the...

Recently bought a used New Holland 2120. Tractor runs great but after running the tractor in high range it will suddenly act like it is not in gear (even though it is in gear and the shuttle shift is in Forward). The tractor then fails to start once the engine is shut down. If you let the...

My 2120 is a 1996 model. Suddenly it will stop moving. Motor continues to run. if I change the 10 amp fuse in the three fuse block on the left side of the firewall the tractor will start and move again. Seems like this occurs when the tractor has been working a while and is hot. I drained about...

In trying to remove the front cover to check out what I think is a leak in the power steering control valve, I'm stymied by this switch. In all the years I've owned this tractor I've never used it and I can't find any mention of it in the manual that came with the tractor or even the full...

Hi all, just bought a 1988 new Holland compact 2120 with loader, has the Asian 4 cyl engine, the Hydraulics don't work, it has 2 hydraulic pumps on the side of the engine, what do each of these pumps operate?? it also has the shuttle shift.. my friend I purchased it from claims he can bleed air...

Hi all, just bought a 1988 new Holland compact 2120 with loader, has the Asian 4 cyl engine, the Hydraulics don't work, it has 2 hydraulic pumps on the side of the engine, what do each of these pumps operate?? it also has the shuttle shift.. my friend I purchased it from claims he can bleed air...

Hi All, have a ford 2120, has the shuttle shift, loader - 3 point, the hydraulics seem to quit working on it,drives fine, then I will bleed the hydraulics and the lifts work fine, until I let it sit for a few days,then I have to bleed em again to get them to lift, it is also hard to start, but...

I picked up an SIMS cab for my 2120, does anyone have any pictures of the cab to tractor mounts? The cab didn't come with any mounts. It looks like the front mounts may attach to the tractor's sheet metal and the rear mounts to the fenders. This is a old cab that has soft sides. Thanks

Does anyone know if the braided rubber hoses on the New Holland 2120 (late model Ford 2120) are Metric or English? It looks like the same braided rubber hose is used for fuel, radiator drain, and power steering. This tractor is now 20 years old and I want to replace all of them but don't want...

Happy New Year to All (except for me since my tractor won't move). I have a 2000 Ford/NH 2120 with HSS. It has 1200 hours on it. The tractor randomly slips into Neutral and won't move. Shortening the Clutch linkage rod appears to help get it going again but only for a short while. If I...

My 2120 has a hole in the block. Looking for a block or engine Thanks Andy

I have a ford 2120 that will not move in forward or reverse. The diode in the HSS system is bad, anybody know here you can by a replacement diode instead of the whole HSS unit the picture is the diode I need

This is concerning a 2000 New Holland 2120 compact tractor I purchased the tractor with this problem so I have no back story or history on it. The tractor would not move forward or reverse so after a lot of investigating I found the power steering pump input shaft was sheared off. The...

Hello, I just purchased a 1999 New Holland 2120 that will not operate in forward or reverse. The loader works and has plenty of power. The power steering does not work. I did some research and read where a couple people had a diode go out in their control module. I checked this and that...

Sorry to come on as a new member and my first post is asking for help. Have a 97 2120 that the brakes have left town on. How hard a job is it? Are any of the after market disc's worth using? I will probably drain all fluid and replace filters since I'm sure there are pad parts floating in...

Looks like my tie rod ends are officially whooped. My tractor is a late 80's model. Not precisely sure. The part numbers I am coming with are SBA334800631(LH) & 641(RH). Just want to be sure the part numbers are good for 2120 Ford/NH tractors throughout the production. In the past when I...

I had the tractor running for 30-60 min and then it suddenly died while moving some brush. I thought maybe I picked up a stick at first and hit some kind of a safety switch but I didn't see anything and the tractor could still turn over. I tried to open a fuel line to the injector but did not...

Moved thread Moved thread. Don't know how to delete :)

Hello fellow tractor owners, I need help locating an attaching kit for a 758B backhoe to a Ford 2120 tractor with a 7109 front loader. I have the 758B backhoe with the subframe but can't attached it without the hanging flanges that attach the subframe to the tractor frame. Also need the remote...

I'm looking for hydraulic info for DIY remotes. Swapping grapple and snow plow from Case 395 to Ford 2120.

I never noticed until it was pointed out to me,my 1995 ford new Holland whines in reverse. Diesel with shuttle shifting. I have had it almost 2 years. First tractor. Thanks

This post is actually about my neighbor's Ford 2120. He was out pushing a pile of brush and lost all control of steering. I went over and looked under the tractor and the steering cylinder was disconnected from the chassis. All the lines are still intact but the bracket that connects the...

Have installed new module switch on lever and have voltage to the solenoids...thanks for any ideas or suggestions.

Is there a way to adjust the dual clutch w/o splitting the tractor?! I have a front loader on it and I do not see any opening which would allow to adjust the clearance between the transmission and the PTO clutch. I understand that there are three bolts which can be adjusted so that there is no...

My rear PTO, (only PTO) will not disengage. I pull the lever back, it doesn't go all the way back and sounds funny. I have tried leaving the clutch in for maybe 20 seconds. I have tried going forward and backwards. I don't have any attachments that use PTO yet. My guess is it got bumped, by...

I am usually the first guy to say get a manual, but I haven't yet. I have had starting problems. I put 10amp charger on for 20 minutes and it starts. I let it run. Have run it around 8 hours. It will start right after a stall. But not always if it sat. Last week charged it, then...

I have a Ford 2120. It came with a Ford 758 backhoe that is totally shot, too expensive to repair. I'm having a hard time finding other backhoe attachments that will fit and run on my tractor. Any help you can offer is appreciated

My 1992 Ford 2120 has been great but I've been struggling to figure this issue out for over a year now. I致e been putting off posting about this until I had as much information collected as possible so here it goes. The tractor will periodically get into the habit of randomly dropping out of...

Hi guys My NewHolland 2120 hss has about 900 hours on it and has been used mainly to load mulch and grading out for lawn installs. Starting last year it began cutting out when engaged in forward or reverse. It was like the tractor was shifted into neutral. After a few seconds it would...

trying to determine if indeed my clutch disc is the problem. changed hydraulic filter and fluid. clutch slips in forward gears (engine revs, but no power). reverse seems unaffected which is why i question the diagnosis? I have a ford 2120 hss mode command.

trying to determine if indeed my clutch disc is the problem. changed hydraulic filter and fluid. clutch slips in forward gears (engine revs, but no power). reverse seems unaffected which is why i question the diagnosis? I have a ford 2120 hss mode command.

I have a 1995 Ford New Holland, diesel. Shibura. Looking for oil filter #. When I look it up Fram nothing for New Holland, and for Ford it calls it Ford diesel, not Shiburu. The tractor doesn't live with me. I'd like to get a filter and go change it. I didn't look at filter last time I...

First tractor, no attachements, other then FEL. Just curious what size my New Holland 2120 diesel can operate. Not really looking to go as big as I can. A few extra passes probably not a big deal. I'll be hooking it up by myself. Figure to get it on blocks and be able to back up to it. I...

I can't get the 4wd to stay engaged on my 1995 2120, unless I hold the the lever down with my foot. Am I doing something wrong? Something need to be lubed or iced up? Thanks.

I have a Ford 2120 with 18.4 x 16.1 R3 turf tires that are well worn and one is leaking. From the research I have done it seems it will cost a fortune and be very difficult to find the proper size rims to change this to the factory size R1. Searching around on the internet I have found...

been a long time lurker of the sight and usually find the answers I am looking for. I hope someone can help me and I am attaching a parts diagram. My problem now is the shaft (#7) the the 3pt lift lever (#14) mounts to has broke off where it make the L shaped bend. After looking over the parts...

My first winter with New Holland 1995 2120, 1900 hours. Manual says full throttle to start, but only starts at all the way back. Low oil light stays on. I started a few times, and let run 20 seconds, barely running. Plugged it in, same thing. Turn key back the glow plug light does mit come...

I'm building a hydraulic log winch to run with my NH 2120. I do not have rear hydraulics. I'm pretty ignorant when it comes to hydraulics and the terminology. The hydraulics on the tractor are "open spool" from what I can gather. I do have a NH 7309 FEL. The $1500 remote kit from NH is a...

right brake peddle does nothing. wet brake system? have not removed housing cover on side of tractor

Hello to you all from Worcestershire in the UK, problem as follows: make & model: Ford 2120 compact tractor (built 1995) problem: low engine speed (rpm) when the hand throttle is set to idle (minimum) or maximum (with no load), same problem with foot throttle. All parts appear to be in place...

Hello new here, but I fig it be better to just start another post on my 2120 heres what I have , ford 2120 I can start the 2120 put it in gear and will go maybe 50-100 yards then act like it slipped out of gear. tried shifting into all ranges and all gears and still no go. can let it sit...

I have a ford 2120 with the hss transmission. When placed in gear the tractor sits a while and then takes off.The same is true when stopping and shifting to reverse.The clutch pedal has an inch of use at the very top of travel. The pto does not work at all.Once moving the tractor seems fine and...

I replaced my clutch on my 2120 and now my hydraulic system does not work. Please help.

May be looking into purchasing a 2120. I have limited information at the moment. The machine is at my in-laws. I used it once a few years ago and seemed to run good. The tractor is a couple hundred miles from me, so it will be a while before I can look at it. What I know is it was originally a...

My neighbor has a 2120 4wd and was moving logs with his front mounted pallet forks when the right front wheel fell off. Not sure what failed first, bearing pieces were found on the ground. I'm impressed that there wasn't more extensive damage as there was a huge load on it at the time. Parts...

My tractor has decided to not change from forward to reverse, regardless of where the shuttle shifter is moved. The shifting was working fine while moving snow with the loader and then no more reverse..... In the past when starting the tractor, it would always be in neutral regardless of where...

does anyone know where the hydraulic clutch packs for the shuttle shift are located in this 2120 ?? and whats involved in getting to them?? Thanks all :confused:

I have a Ford 2120 with a shuttle shift. Anyway I have the tractor apart and noticed the shift fork is a little worn. I was told that the fork wear migh be filled with brazing or welding. I can weld cast steel but I would not feel comfortable welding on cast iron. New forks are not available...

Hi, I have a 1995 Ford 2120 with electronic shuttle shift transmission and 4 wheel drive. The tractor was serviced this summer because the PTO was locked up and damaged the PTO clutch and other parts. The tractor ran fine for 3 months. Recently the transmission would stay in forward when...

Hi, Just purchased this neglected tractor and doing some maintenance I noticed the cable that attaches to clutch pedal, the mount is broken or missing. Does anybody have a picture of theirs to see what I need... Thanks

Hi everyone, New to tractors here and i got a Ford 2120 when we bought our new home here in Petoskey Michigan this summer. Had it in to the dealership to change all fluids, filters and then give me an orientation on this tractor. Also had the from gear boxes rebuilt at the same time to stop a...

My transmission keeps getting Stuck in a gear. Sometimes Reverse sometimes 1st sometimes another gear. Have checked the linkage no issues there the shifter paw was worn welded it and ground to "fit better" but it still gets stuck and have to pull the top off and go in to free it up again. Is...

Can anyone advise me where to find a detailed parts list for a 2120? I need a replacement outer rear shaft seal and am struggling to locate one. The numbers on it are M70 95 17. It is a strange double seal which has a rotating inner section rather like a mechanical seal. Any advice would be...

Good evening everyone, my name is Simon and I thought id better say hi. I am a small plant engineer based in Scotland's beautiful west coast. It's raining again! I get asked to help with the local farmers' tractors and other agricultural kit from time to time. I am hoping this might be a handy...

Hello everyone. This is my first post. I have a NH 2120. It was working fine. parked it and when I got on it again a few days later it wouldn't move. I am pretty sure it is the HSS module but I'm not sure exactly how to diagnose it. any help would be appreciated. it is a 12x4 transmission with...

I have changed the fluid and filter however the loader and 3 pt hitch will not move. any suggestions as to what I should check next

Hi, this is my first post here so I apologize if my inexperience shows. I have my Dad's 1992 Ford 2120 which I've taken pride in always starting. However since an abortive start attempt on a 0 degree morning which very quickly killed the battery (I know I should have had it plugged in but it was...

Hello everyone, newbie here, great site with alot of info! I am looking at a 89 2120 with 1 remote, fel (7109) qa bucket, 1900 hrs, 4wd, loaded rears. Just serviced. Dealers asking 12000. I really am into the 2120s but dealer said this unit had a subframe bh on it. Questios: 1) is the fact...

I found a Ford 2120 with a FEL for sale. Tractor is low hour and in good shape but does not have HSS. How big of a deal is that? I probably won't be loading materials with it much but I can see myself using the FEL for grading leveling and perhaps moving snow sometimes. The tractor is priced...

Hi, I have a 2120 4cyl and while pushing some snow I noticed an idiot light or dash light on. The light is a circle with a line threw it. The circle is a normal circle but the line is sort of wavy going through the circle left to right. Any ideas what this means. I have a manual on order now but...

I bought this Ford 3rd hand and do not have manual for it. I blew a hydraulic line moving the snow around here in NJ and replaced. Now I want to fill up any that I lost. Problem is, I do not know where to add the oil? It is a 1988 2120. Thank you.

This tractor has a significant hesitation when changing direction. It doesn't matter which range you are in. Since I have changed hydrolic oil and filter it is very slow to move and will only operate in low or medium range and only in first or second gear, loader drifts down after raising and...

I just put a Herd 3 point sander on the reader for my Ford New Holland 2120 (model year 2000). My paved driveway is *very* steep and winding, with the home (log cabin) at the high end. I plowed the nominal snow off with my truck, which went down and up without issue. I want to sand to provide...

I would really like an e-manual for my Ford New Holland 2120 with frame mounted back hoe. If anyone knows where I can get one, please let me know. I am not trying to avoid paying the costs of a real manual, I just know an e-manual will serve me better. I want to detach the frame mounted...

Any help would be greatly appreciated. I have a 1998 New Holland 2120 with shutle shift. Not sure if that's what New Holland calls it but as you know should be able to from Forward to Revers without using clutch. Well I can but when I do shift it just goes into neutral or feels like neutral for...

I need to remove the frame mounted backhoe from my Ford 2120 to transport it (on a smaller trailer). I haven't picked up any service manuals. Does anyone have the directions handy, or perhaps even a video? I am presuming it is a Ford 758B backhoe or similar (but I have not found any markings for...

how much oil for an oil change for a ford 2120 diesel ?

Recently bought a 2120 tractor and am trying to find out if there is a subframe kit that works with the New Holland 757c backhoe my father has on his TC33d. Does anybody have any details on this? I'd rather buy a subframe kit than weld something up in this case. Thanks!

I have a trailer with an 18' bed and 7k axles. Am I going to find a way to trailer a Ford 2120 with loader and backhoe on it? Perhaps with it backed on and the back hoe hanging near the tongue of the trailer? I do know I need to tie down the tractor as well as the two attachments separately. I...

I just bought a 2000 Ford 2120 with backhoe. When I used it Saturday some welds broke on the mounts. These appear to be the only connecting parts between the tractor and backhoe. Is there something missing, or if not, is this a common failure, and what is the suggested repair?

I just bought a 2000 Ford 2120 with backhoe. When I used it Saturday some welds broke on the mounts. These appear to be the only connecting parts between the tractor and backhoe. Is there something missing, or if not, is this a common failure, and what is the suggested repair?

I have a 1994 2120 with EHSS 12x12 transmission that uses the one way bearing (sprag clutch) to drive the PTO. I am pretty sure my pto is loosing power and stopping due to this. I bought the Ford/New Holland major shop manual not the I-T manual and it appears I have to split the tractor between...

Hello all, Hopefully some one can help point me in the right direction. I have a Ford 2120 HSS Last year i was running it and the tranny started slipping(I was low on oil),,,I noticed below i was blowing hydraulic fluid out of the Hydro case, the one in front of the gear box. There is a...

I have a ford 2120 with HSS shuttle shift that will not shift from netural. Have check the shifting solenoids mounted at the steering column and they are getting voltage and seem to be working. Any other ideas?

I am having problems with the hydraulics on my NH 2120 tractor. I use the tractor for my firewood business; so I have a bucket and Farmi Winch on the tractor. Recently, I have been experiencing problems when the winch is lifted. When the winch is fully lifted the tractor still labors as thought...

pto stopped working when tilling

I think that the heading says a bit but here are the details. I have a 1994 Ford 2120 4WD with 2 stage clutch( and a safety cab). Recently after a day of fairly heavy dung shifting the clutch developed some slippage which meant that getting the tractor back to its shed was problematic. Checking...

Hi, I have just bought a Ford 2120 tractor that came complete with a Lewis equipment backhoe and FEL. The backhoe is a 300 series. Im not sure about the FEL. It seems to have been fitted to spec to the tractor. I have used the backhoe for the first time this weekend. The hoe is being ran off...

I have 2 tractors - a 1967 MF135 with an MIL trip loader but no power steering and a 1994 Ford 2120 4WD without loading gear. I'm thinking of tooling up the Ford with a modern(ish) FEL which would enable me to sell on the MF to someone who'd like to restore it. Can anyone share wisdom on the...

Looking at a 1989 2120 with 7109 fel and a Sims welded cab w/ 12x12. Anyone care to take a stab on it's value? Thanks. Sorry-1509 Hrs.

Looking at a 1989 2120 with 7109 fel and a Sims welded cab w/ 12x12. Anyone care to take a stab on it's value? Thanks.

I have read many of the posts about chains on the front of 4wd tractors and it has me a little concerned about doing that, I understand it is probably no big deal if you are careful about how you use the tractor. How ever is it a better use of my money if I buy the correct size ag tire (to match...

I bought a 2120 and it has the turf tires and it is not easy to find used rims and ag tires so thinking about going to chains and a 7 foot snow bucket that weighs about 700 lbs. Is this too much for this to handle, I have a M with a too big a loader and a 7 ft bucket and it handles that no problem.

Talked to a guy about a 1988 2120 4wd with FEL and a ballast boc with 2200 hours for about 12,000, is this a good buy it seems like the ford is much heavier than the other models in that HP range.

Hi, I am looking at buy a used 1992 ford 2120 with a loader and back hoe with 2500 hours on it. The seller claims everything is in good working order and is asking 12,900. I was looking for any suggestions for what I might ask the seller about this tractor to know whether it is a good buy or...

Easy question.... Wheres the hydrolic fluid fill port?

Anyone have any idea what a 1989 Ford Model 2120 with 1051 hrs. is worth ? The unit comes with a roll bar and a non descript snow blower.....over all the tractor seems to be in good shape with some minor deficiencies. Any help would be appreciated. ( Its gov't surplus )......!!

Hi, I'm looking at acquiring a 1989 Ford 2120 with 3710 hrs on it and has a front end loader. I was hoping that some of the members here could steer me towards some good things to look for to ensure that the tractor is in good running condition and some things to watch out for that are signs of...

I have a 1995 New Holland 2120 with a transmission problem. The tractor is stuck in a reverse gear. The clutch is working, but if I try to put the tractor in a forward gear, it stalls and dies. The gear selectors seem to work properly - I can work them through their range of motions. I can take...

My 2120 had been run out of fuel so I filled the tank, And now after bleeding the lines the tractor will only run for 5-10 seconds before stalling back out. It also spits some black smoke horribly. Any help?

I'm looking at purchasing a Ford/New Holland 2120 off a private individual and am curious if there is anyway to find out what the repair/warranty history is. Is this something you'd have to check with the dealer on? serial # - uv26569 model# - av413a unit # - 32022b

Looking for the A Counter Gear part number SBA 322372220 used in a 1988 Ford 2120 FWD gear box that mounts to the bottom of the transmission. Mine broke a tooth and took out both gears. I bought new bearings seal and one gear but the other is back ordered to the MFG in Germany with and unknown...

I am looking for some info on repairing or replacing the one way pto clutch on my ford 2120 it does not turn. i saw a post where someone said to ingage the pto and see if the pto turns counter clockwise and if it did the one way clutch is bad. and mine does that. thanks for any help. Jim

I bought this 2120 new in 1989 and have never had a single problem with it until now. Some of the brake friction discs have degraded and need to be replaced along with several of the friction plates. My question is that it takes 4 per side, 8 total and these parts from Ford New are ridiculously...

Let me first say hello, I have been reading this forum for some time. I have a 2000, new holland 2120, manual trans and I am looking for some ideas of what may be wrong with it. The tractor is stuck in a high forward gear, I can not move the gear shifter lever. The clutch works, but I can not...

i've searched and read through alot of postings regarding this model...but would still like some input on this specific tractor. i'm going to go look at it this wkend (if he still has it)...1690 hrs, 4x4, loader, regular gear shift (no HSS), owner guessing it is mid '90s (won't know until i go...

Hello all! My boss at work (nursery/garden supply center) has asked me to sell the company tractor with it's attachments, and I was hoping to get some suggestions on pricing. We're just south of Madison, WI. Tractor and attachments: 1998 Ford New Holland 2120 387 hours Perfect condition with...

Someone told me that there were higher than average failures on the Ford 2120's Can anyone substantiate this? I have been looking at a used 2120 and am leary of it now.

Looking @ a 88 ford 2120 TLB w/ 1050 hrs. appears to be in good shape but needs front axel seals, wondering if it a major job. Machine would fit my needs perfectly otherwise. Thanks for any advice

Looking @ a 88 ford 2120 TLB w/ 1050 hrs. appears to be in good shape but needs front axel seals, wondering if it a major job. Machine would fit my needs perfectly otherwise. Thanks for any advice

New old guy here. I am going to buy one of the above. The Ford: 2825 hours;FEL; Bush Hog and snow blade included for $10,000. The TC33 625 hours; FEL no other equipment come with it. $11,954. Primary use will be for firewood cutting and snow removal. I will probably not keep Bush Hog...

Can this Ford 2120 take a 72" or 84" MMM? Tractor is pretty local to me. My idea is to make a dedicated MM mower out of it. I don't know if it has a mid-PTO...

I bought a '97 New Holland 2120 with 105 hours on it. I need to change the motor oil and the manual specifies a SF/CD approval. I want to use 10-30 due to temperature swings in PA. Does Rotella make a 10-30 (can't find it) and if not can someone give me another brand suggestion? Everything...

Found a local 2120 for $20,000 with the following specs. The machine looks good, not abused and runs smooth. Is this a fair price? 1997 New Holland Tractor Model 2120, 40 HP, 4 WD, 1318 Hrs., 12 Speed Transmission w/shuttle shift w/newer Woods 9000 Backhoe w/18" bucket and newer Woods 1020...

Could someone tell me if a Ford 758B backhoe that is coming off a Ford 2120 would fit a 2110? What is the difference between the two tractors. This is a frame mounted unit. Thank you.

I posted this under NH but so far have no answersI have found a Ford N/H 2120 with over 6,000 hrs. It appears to run smooth and quiet. It was a golf course tractor. The only problem tha I could make out right away was the lack of a clutch. The dealer wants $5495 for the tractor as it sits. He...

I have a blown transmission and cracked casing in my Ford 2120. Has anyone tackled this job on their own before or am I better to send it out? Any suggestions on getting used parts?

I just purchased a 97 2120 and a few places on the loader and the white rear fenders need a little touch up paint. Are the paint codes for the blue and white in the owners manual or can I tell from the serial number, or does anyone happen to know them? Thanks

Does anyone know if an older ford 2110 compact tractor front grill is the same shape (fit) as the newer 1987-2001 compact 2120. I know the older ones were white and mine is painted black but the shape "appears" to be the same.... I have found the 2110 grill available aftermarket for about $110...

I am looking at a 1999 NH 2120 with 191hrs on it. they have a price of 15,00 is this a good deal? I have yet to see the tractor in person, but will hopefully be going to look at it soon. Thanks

Hello all, traded a good 4 wheeler for my lastest project!! really has not been that bad so far, anyways got the beast back together and added a set of rear remotes and also added the power beyond return at the rear of the tractor for backhoes. The tractor was plumbed with a QC between the PB on...

Anyone happen to know the front bolt circle diameter on a NH 2120. It measures about 7" which is close to 180mm. Looks like I need to have custom rims made for R4's.

I found a 2003 model 2120 Ford New Holland yesterday, talked to teh salesman today who I have known for quite a while and have dealt with him quite a bit with a guy I work for who farms 2000 acres. Anyway the Tractor is a 2120 4wd with a loader, it's a 2003 model with 650 hours and they are...

It has about 700 hours. Has some dents. Needs a new floor mat, otherwise pretty good condition. Were selling it out here in California. It seems to be a favorite among some folks. It also has a 12X12 transmission. $10,000? Also included is boxscraper (Ford), a brush hog, (Ford) and a PHD, also...

I have been looking at new tractors and just can't decide to buy a TC33D, TC35 or TC40. In my looking I have found a used 2000 NH 2120 4wd with 12x12 shuddle shift trans and 1 remote on the rear with a canopy and 128 hours for 12,900. Is this a good price? Also does anyone know of any problems...

Does anyone know if ag tires from a 2120 will fit on a 1920? I know they use the same size turf tires and wondered if the ags would fit as well. Thanks for any input. Bill C

Anyone with a NH/Ford 2120 or similar with HSS (hydraulic shuttle shift) have or had this problem? Ours now does this all of the sudden. Neutral is now forward. Forward still is forward and reverse locks up and stalls the engine. There is no neutral or reverse. After all the work we have gone...

The NH XX15s, XX20s and XX25s were around before the Deere 4XXX and the Boomers. Does anyone watching have one of these venerable machines? The only remaining models in this line up are the 2120 and 3415 and I don't know how much longer they will be in production. The TC30 is a re-issued...

A Ford tractor 2120 4x4 deisel that won't move. I think it is an automatic trans, the fluid is fine what could be wrong?

I HAVE A 2120 4X4 SHUTTLEBUTT TRANS , TRANS SLIPS,JERKS, AND HESTITATES AFTER ITS WARMED UP.STARTED DOING IT @ 500HRS TOOK IT IN THE DEALER REPLACED THE RELIEF VALVE. ABOUT 100 HRS LATER STARTED ACTING UP AGAIN. THEY DON'T KNOW WHATS CAUSING THE PROBLEM, NO MATTER WHAT GEAR I'M IN.SOMETIMES IT...

Help! Have 5+ wooded acres w/RR and old canal bed and want to build house, barn/garage, and pond. Retired now and looking for a tractor to excavate basement, build pond, put in drive (100+ ft) and then maintain (can take little bites). Thinking diesel and 4x4 and 30-40hp (Kubota L3010 or...

Well, here's the tractor with the owner. I must admit, as mentiond by scruffy or glen or somebody, it's nice to see a face and put it to a username. Derek

My New Holland with HD Woods back blade. Derek