case

  1. P

    Case IH 235 Rear Wheel

    Hi all, I just picked up a Case IH 235 - it was sitting for a few years so took a little love to get it going but it’s running great. My only issue is the rear-left wheel is completely rusted out and I can’t seem to find one that fits this machine. The wheel is 6 lug and seems to be a 100mm...
  2. T

    Kubota Mower Bevel Gear Case setup

    Happens to be RCK54-15BX, looks just like my RCK54-22BX. So, planning my marking and shimming process after new bearings. Parts book and WSM for similar unit shows shims: 2 sets, 1 each end of input shaft, and a single set 'holding up' vertical output shaft. My limited knowledge would...
  3. E

    Can’t run a hydraulic top link on a Case 75c?

    This is the second time this plate assembly cracked in the last week. I’m using a hydraulic top link and apparently that’s what’s causing this plate to crack, I just don’t know how. Anyone have any ideas why it’s breaking this piece? The top link does not come into contact with this piece in...
  4. C

    Massey Ferguson 1528 Final Case Install

    Hello, I've got a MF 1528. It ate a snap ring (#15) on the front axle. I tore the unit down, cleaned everything up, got the replacement part from AGCO. How do I get the final case LH (17) to install over the Final Case (1A)? There are two bearings (14/13) in 17 (inside what is shown as 22 -...
  5. B

    Case DX24E horn relay

    Would anyone know where the horn relay is located? I have a dead short when the horn button is pressed, blows the fuse. Switch gear looks okay, I disassembled it. Thanks in advance to everyone
  6. C

    Case Mxu 110 Smokes

    Hello all. I have a 04 Case MXU 110 that Smokes blue as soon as it starts. It clears up with high throttle, but smoke starts again as soon as I throttle back down to idle. The tractor sat for 5 months before I bought it. The oil was also 3/8 over the max fill on the dipstick. I just changed it...
  7. C

    Case MXU 110 Blue Smoke

    Hello all. I have a 04 Case MXU 110 that Smokes light blue as soon as it starts. It clears up with high throttle, but smoke starts again as soon as I throttle back down to idle. The tractor sat for 5 months before I bought it. The oil was also 3/8 over the max fill on the dipstick. I just...
  8. E

    What is this part on my case 75c

    What is this part? The rear remotes attach to it. I noticed today it was cracked with fluid running out of it. The tractor has less than 600 hrs and is still covered by warranty. I don’t run much off of the hydraulics. Most of my stuff is 3 point, but is there anything I could have done to have...
  9. J

    Case 446

    I have a case 446 I think my hydraulics are wearing bad I think my hydraulic pump is gone whenever I try to pull anything with it I have a loss of power but not a loss of engine is there anyone that can send me a video of how to remove the hydraulic pump so I can get it rebuilt
  10. D

    Case IH 245 Tachometer bouncing around and making whining noise?

    See video/sound and pics here- Tractor Tach I'm guessing I need a new cable. Any tips for replacement? Should I remove black instrument panel to access the back of the tach? Should I disconnect at engine while operating until I get it fixed? Do tachometer cables need any periodic lube...
  11. J

    Case DX45 PTO pressure

    Working on a 2004 DX45 that the PTO doesn't stop turning. Turns out the brake in the PTO clutch was broke off and the stop plate worn. Is it normal to have about 75 psi on the PTO line when disengaged? We have the service manual and it doesn't have a spec for the disengaged pressure. We don't...
  12. T

    Case IH mini 255 tractor

    Hope this is an easy question for someone on here. I need to know if my Case IH 255 Mini tractor with Mitsubishi K3E motor has cylinder sleeves. My parts break down does not show any and none of the cylinder rebuild kits show for 255. they all say 234 and 235 tractors. Trying to rebuild...
  13. N

    looking for a case 1816 manual?

    wondering if anyone would have a manual or a link to a manual for a case 1816 uniloader (skid steer) or maybe someone could give me some wisdom on whether theres a way to pull the unit (non running) is there a bypass valve for the hydraulics? or some way to disconnect the drive motors from the...
  14. J

    IH Case axle issues

    Reaching out to find anyone else that may have had front axle fail with the 6 bolts, flange/washer holding gear in place axle configuration in a IH Case tractor. I have the 105C model. I bought with low hrs. and at IH dealership with limited warranty. The first right side fail was done right...
  15. A

    Identification d'un tracteur retrocaveuse Case ???

    Bonjour, Je suis en France et on me propose un chargeur avec rétrocaveuse Case mais je ne sais quel est le modèle (580CK, 780 CK...?) le propriétaire non plus. C'est très ancien. Merci à ceux qui m'aideront un identifiant cette machine.
  16. L

    Case 1594

    We have a Case 1594 tractor. It is working with idling but once it gets to a high RPM it dies. Anyone have any suggestions on what could be the issue? Thanks.
  17. D

    Case IH JX95 stops while plowing

    I have a Case IH JX95 that appears to be running fine until a put a blade in the ground. It running without fault for 100 or so yards then the engine revs slow until the engine stops. Turning of the engine cranks for awhile, then revs to the proper rpm for 100 or so yards for the revs to slow...
  18. P

    Need to split Ford 1210 at the transmission case. Looking for advice

    I have had the fwd/rev control rod detach inside the transmission case of a Ford 1210. I've searched forums to learn that it is common, but there's not much on fixing the problem. Has anyone split the Ford 1210 at the transmission case and are there any pitfalls to avoid? manuals I have only...
  19. somanytractors

    My case 580B has a reset button on the dash, can anyone tell me what it does?

    I've attached a few pics. I have no idea what this is for. It just says push to reset, and it looks like a hose coming out of it and going under the hood. I didn't trace it because even if I did find where it goes, I still wouldn't know what it does. Any info would be greatly appreciated
  20. bmaverick

    Deere loses appeal in patent case against AGCO and Precision Planting

    Deere loses appeal in patent case against AGCO and Precision Planting By AGDAILY Reporters Published: January 27, 2025 https://www.agdaily.com/technology/deere-loses-appeal-in-patent-case-against-agco-precision-planting
  21. caver

    Case 580K A/C compressor locked up

    Last week when it was in the low 50's I visited my property and discovered the A/C compressor seems locked up on my cabbed backhoe. I started it up and heard something start to squeal under the hood. I may just cut the belt as it looks like I may have to take the cooling fan off and the belt is...
  22. R

    Case IH STX 450 Clutch position potentiometer

    Hello! My Case IH STX 450 doesn't move. At first, the error code was 56016. We took out the potentiometer at the clutch pedal. There is 8 volts in the wire. If we reinstall it, we can't calibrate it. The star (*) does not appear on the calibration display. However, if we take it out and use a...
  23. R

    Case STX 450 clutch position potentiometer

    Hello! My Case IH STX 450 doesn't move. At first, the error code was 56016. We took out the potentiometer at the clutch pedal. There is 8 volts in the wire. If we reinstall it, we can't calibrate it. The star (*) does not appear on the calibration display. However, if we take it out and use a...
  24. AC Mack

    Looking for 1200x24 Rice and Cane tires for my CASE tractor restoration

    Anyone know a source for new 1200x24 Rice and Cane tires for sale? I see lots of 12.4x24's. What kind of difference is there between a 1200 vs 12.4? Are they wider or taller than a 1200?
  25. AC Mack

    1943 CASE SI Airborne ARMY tractor

    I just picked up a 1943 CASE SI Airborne tractor. The VIN is 4711035 SI. I think that puts my build year at 1943. Can anyone confirm that? The instrument panel is Olive Drab, the rest of the tractor is painted in primer gray. Done by the former owner who began restoring it. It does not have...
  26. X

    case jx1090u

    I have case jx1090u. The power steering and the front loader have a tendency to stop working in below freezing weather i asume there is water in the oil, but i can t find where to check and or empty and or refill. All tips are welcome.
  27. X

    case jx1090u

    I have case jx1090u. The power steering and the front loader have a tendency to stop working in below freezing weather i asume there is water in the oil, but i can t find where to check and or empty and or refill. All tips are welcome.
  28. M

    1983 Case W18B air issues

    I have a 1983 Case W18B wheeled articulated loader. When I start it up, it's not providing enough air to release the parking brake. I aired up the air tank with a compressor and found both the brake pedal and clutch/brake pedal are leaking air from the bottom when the snap ring is. Anybody ever...
  29. T

    Case IH 885XL - replacing ignition switch

    I have a 1987 Case IH 885XL w/ cab that we have moved into the shop for some winter work. I have purchased a new ignition switch and a new turn-signal switch to try and eliminate some intermittent but increasingly persistent problems with the current switches. I looked in the PDF of the owners...
  30. O

    Comparison  Kioti CK26 vs TYM 2515

    Hello, I'm trying to compare compact tractors for heavy loader lifting (with backhoe counter weighting and ballasts). Also, I'm interested in details that make these tractors unique apart from eachother. I wanna lift [EDIT: NO] more than 1700-1800 lbs. Would rather a 25hp to avoid DPF if I need...
  31. chris the wrench

    Cleaning transmission case

    Im about to bite the bullet and drop the 48re trans out of my 2006 ram 2500. Im thinking Im going to rebuild it myself. Ive looked at a bunch of parts kits and videos. Ive done a bunch of engines, a few vw transaxles, but never a auto trans so this will be an experience. Looking for ideas to...
  32. murphyhead

    Case CX90 clutch

    Hi all, I have changed the clutch on my cx90 a few times over the years. The last two times the clutch wasn't badly worn at all. It's currently not great at all and hard to get into gear. Here is what's happening. With the clutch fully pressed and shuttle in forward or reverse, when I try to...
  33. A

    New Holland Workmaster or Case Farmall 75A Fuel Tank - Tractor Runs then Dies

    I'm posting this in case someone else runs into this issue and hits the google machine looking for an answer. If you have a New Holland Workmaster or the Case Farmall A series (which are the same pretty much, just different colors/names), then this info might be useful to you. You may run into...
  34. R

    Request for info: 3PH 'leveling box' (side link) dimensions on Case IH 595, 895, 995 or International 464 684 454 484 574 784 584 674 884 402635R4

    If you own one of these models, can you tell me the diameter of the pins at top & bottom of the side link, and the approximate distance between the pins (from hydraulic arm to lower link)? The part that fits these tractors seems to be quite common, but none of the vendors offer actual...
  35. jgriffith8

    Case Farmall 55c - Rear tire chains

    I picked up a 2022 55c and have been pretty happy with the tractor overall. Couple little things I don't like particularly around ability (or inability) to climb a hill in medium range under any sort of load and the inability to tilt and raise the bucket simultaneously but that's about it so...
  36. M

    1980's Case IH 275 k3m head

    1980's Case IH 275 k3m head I need a head,I'm looking for sites or someone that might have one for sale.Thanks
  37. K

    Case 1816 uniloader

    Do I have to pull the engine to replace the starter on a Case 1816 Uni-loader.
  38. 1

    Case 580 CK Service Manual for sale

    I have a like newset of service manuals for a case 580CK I want to get them to someone who can really use them. $85. plus postage 855090,855091
  39. J

    2006 Case JX95 Light Wiring Help Needed

    I have a good friend that I'm trying to help get his hazard lights and dipped lights hooked back up. The problem is a guy that did some work on his tractor unplugged the wires from the two switches and didn’t take a picture or anything of them. So I'm looking for somebody that has the same...
  40. N

    Case 485

    I have a Case 485 that has about 1000 hours on it and the differential lock is stuck. I have put around 100 hours on it over the past 15 months. The hours appear to be right because it had the original tires on the rear. First thing I did was replace them because I could see the tube in the side...
  41. B

    Case 580SE Parking Brake, Friction Disk, Counter Shaft Spline Wear

    I bought a 580SE 2WD and one issue I have if that the trans-axle counter shaft splines are worn where the parking brake friction disk is located on the shaft. I bought this backhoe from photos and I knew the brake assembly was missing so I purchased all new parts to install the brake and had a...
  42. dlbraly

    Case 480E Box Blade question

    Looking to find a seal kit for a hydraulic actuator, but Not sure which one to pick in the Parts Catalog. What is the cylinder called that tilts the box blade front to rear (Not side to side or up and down). Circled the one I mean in the picture. I bought this tractor like this, the way the...
  43. A

    1983 case 480d steering issues after complete rebuild

    i have a construction king 480d/ll front loader/skip drag. i have pulled the control valve and had it rebuilt at local hydraulic shop because there was fluid coming up through the steering wheel. i had the steering rams rebuilt, they do not appear to be leaking. also replaced the power steering...
  44. U

    What model is this Case planter?

    There's no tag or identification that I can find.
  45. dlbraly

    general inspection and Leaks - Case 480E

    I knew it had/has leaks when I bought it a week ago. After my chores Today Pressure washed, Added some fluid and ran the hydraulics. Not as bad as I thought it might be. Have a few actuators to rebuild. Both Steering actuators and the steering ends Right Loader life cylinder seeps 2 out of 3 of...
  46. H

    2590 Case Wiring gremlin

    Hi , I am wondering if anyone has run into this situation before on a 90 series. My alternator light came on my dash so I pulled it apart and found the Voltage regulator out of limits. So I replaced it and I did do all the checks on the stator, Rotor and rectifier bridge and all passed. So I was...
  47. ArlyA

    Case 20-40 Tractor was my grandads.

    This is the tractor my grandfather owned and operated. (same model) He was a WW I vet and served in France and the son of Norwegian immigrates who homesteaded the land he farmed. He passed in the 1970's and this is the tractor, but not him in the photo. I did see movies of it in operation...
  48. A

    1816C case drive pump

    Just got it running ,sat idle for years and now the new belt on the left side burned of in about 1 hour and was sqealling. How do I determine if it is the pump or the drive motor. I can put a cheap belt on it a see if it burns off and squeals without using leaver. Open to suggestions.
  49. L

    Case ih d 45

    2001 case ih d45 2000 hours in good shape . Is that alot of hours ? Are they a good tractor?
  50. J

    2008 Case IH Farmall 31 Tractor Loader Cab and Mower

    Im looking at a 2008 Case IH Farmall 31 tractor with loader cab and belly mower, owner says it has around 400 hours and runs fine. Its been sitting for sometime outside and currently the battery is dead and owner claims he hasn’t had time to use it and is looking to sell. Wondering if anyone has...
  51. H

    588h case lift

    Having a ats failure code and is derated. What are some possible things to check out.
  52. J

    Kabota L 275 Hydrolic fluid spews in to the case after changing hydrolic pump. What is causing this? Thanks

    I changed my hydrolic pump and now hydrolic fluid is going to the case and spewing out any ideas on what is causing this?
  53. G

    Case 680k boom cylinder removal?

    Trying to get left bucket elevator cylinder off. Lower snapping no problem. Upper one not normal snap ring but is very thick with only a split, no holes like snap ring. Any help would be appreciated. Large snap ring tool won't get it? Help please
  54. J

    LX2610 Cab - Front Axel Case fluid replacement

    The manual says: KUBOTA SUPER UDT-2 SAE 80-SAE 90 gear oil Why specify 2 options? From what I've read it ships with UDT. Recommendations? I'm looking at buying the AMSOIL SEVERE GEAR® 80W-90 100% Synthetic Gear Lube for it.
  55. H

    Case IH Warranty claims

    Hi, I have a Case IH Farmall 60B tractor it’s about 13 months old, 220 hours and still covered by warranty. It developed an engine noise and lost power when I went to up the revs to turn on the PTO. The dealer has done a pressure test, and said there were bits of metal in the oil. They say it...
  56. 1

    Case 580CK set of factory service manuals in excellent condition

    I have a full set of factory service manuals for a Case 580CK that are pretty much like new. I would like to get $90. for them plus shipping. Thank You
  57. Deere Dude

    Rear Finish Mower  Gear case oil removal

    I have had a RMD2584 for 11 years and it works fine and has maybe 500 hours on it right now. I am considering changing to gear case oil in it. I can't figure out how to empty the gear case as there is a dipstick hole on the top and a hole in the side for the level, but nothing on the bottom to...
  58. G

    Case IH MAXXUM 140 will not backup

    My Maxxum 140 Pro will not backup when I Shift the shuttle to R (reverse), it goes forward . It did this a few weeks ago, but it worked after setting over night. I let it set over night , but that did not work this time. Still will not backup, does anyone have solution. Thank Gary .
  59. I

    Case IH 2290 hydraulic hose connected to the hydraulic pump

    trying to fix my case 2290's hydraulic leak ive identified the leak to the hose that runs from the hydraulic pump to the main controls in the cab, i cant for the life of me figure out how to remove the hose, it spins freely but doesnt unscrew, and its not a push pull release refrence pictures...
  60. M

    CaseIH Farmal 65A

    Hi Everyone, Have a 2012 65A that we keep around the farm for light duty work. It is lower hours (under 1200) and we have started having an issue with it today. After about 45 mins to an hour of run time (this time it was on a rotary rake), it will begin to churn smoke and lose power. Once you...
  61. J

    Case-ih 485 injection pump parts

    Hi everyone I recently added to my project list a pump rebuild on a 1985 case-ih 485. Project started as someone else's good idea and I'm left trying to get it to back together and running again. I either need a reasonably priced good used injection pump or a parts pump. Does anyone here know...
  62. KilroyJC

    Parking Brake Retrofit? 1962 Case 430 (and I remembered pix BEFORE making the post this time!)

    The parking brake on my tractor is pretty much useless. It is a coarse-stepped metal tab on the starboard-side pedal that engages with the footboard (you can see the wear in the photos) and the steps are so far apart for the ratcheting action to provide sufficient pressure to keep the tractor...
  63. KilroyJC

    1962 Case 430 Diesel - Dumb Question: Oil Breather Removal?

    I feel like a moron that I have to ask this, but I cannot remove the breather/fill cap atop the hood. it just spins, it won’t slide up, it won’t push down (like a bayonet mount), I made a paracordnsling and tried pulling with two hands. . . What am I doing wrong? I really don’t want to have...
  64. KilroyJC

    Anyone have an old Case parts book they can look something up in please?

    I would like to change the hydraulic filter on a 1962 Case 430 with the 188ci Diesel, manual clutch/transmission, manual steering, single control for attachment up/down, I can only read the first two numbers on the Wix filter “31?” The rest are obliterated. Any help would be greatly appreciated!
  65. KilroyJC

    Going to try swapping my lift arms left-for-right…

    1962 Case 430 The lift arms are somewhat splayed, and so the ends are just a wee bit wide for hooking up without having to pull them together with a ratchet tie-down and some “easing” with a ball-pein to hook up attachments, which pretty much defeats the whole idea of the Eagle Claw “QUICK”...
  66. N

    Does anyone make a pin on to global adapter for Case 580?

    Hi everyone, I thought this might get more info in this forum. I'm looking to convert my old 580C to the global style quick attach. Can't find any adapters for it. Maybe someone makes a universal FEL adapter that I can make work. Does anyone know of an adapter that will fit? I know some will...
  67. G

    slow, touchy hydraulics case 685

    hey folks... ive recently picked up a 685 that was owned by a good friend the short of it i bought it cheap 6k with a 7' bush hog post hole digger and a set of forks for the loader (westendorff) i knew it had a few minor issues. bare with me as im a transformer/power substation builder, and...
  68. KilroyJC

    “Abandoned” Case 310 dozer

    On the lot next to the one we just bought, which is littered with various abandoned vehicles, trash, and squatters, is a Case dozer. When we finally get to contact the owner, it may be something I would like to add to the collection. I am not going to trespass, so I cannot provide any more...
  69. KilroyJC

    Greetings and Salutations

    Hello! New member here, New tractor owner as of three days ago (I am the “new“ - the tractor is older than me), hopefully I will be able to find a lot of answers to questions with (SEARCH) instead of asking questions that have already been asked & answered multiple times... Last night, we went...
  70. S

    Case 275 randomly stops moving.

    Hey everyone, I have a 1988 Case IH 275 compact tractor with a 3 speed transmission, and a 3 speed range transmission. Everything on it works great, except it will randomly stop moving while going in forward or reverse. After about 2-3 minutes of the tractor running, it will just stop...
  71. B

    Case 245 lift issues.

    198? Case 245, 7qa loader. I notice last week that it started to have issues raising the loader, and the 3pt hitch. it is slow and jerky, until it has run for awhile and then it seem Okay. it is between 60 and 70 degs here. The fluid level is good, but is milky, but has been for a while...
  72. M

    Reverser parts John Deere 410B Reverser

    I am looking for where to buy aftermarket parts to rebuild the reverser in my John Deere 410B. There is a company in Louisiana that rebuilds them for $4300, ouch!! Naturally they dont offer a kit nor will they say where they get there parts from. I have read on some forums that these...
Top