Search results

My 2400H has developed problem where it is very hard to get started when engine is at ambient temps of 30 - 50 degrees F. It will crank and sputter and then finally start and run rough like on two cylinders for several seconds before firing on all three. This was a pretty sudden change since...

Does anyone have a cross reference for the HT17160000A3 glow plugs used in the A1100N2 engine? I have performed multiple searches to no avail. Marking on the glow plugs are: OL3 on one hex A52J 11V on another hex M10 x 1.25 threads 17.5 - 18 mm heat tip 5 mm dia Approx 25 mm from tip to...

Does anyone know the approximate weight of a tandem 3,500 lb drop center boat trailer torsion axle assembly. Have not measured but estimate around 84” between mounting brackets. My son had a bearing go bad and destroyed the spindle on axle so now have to remove axle assembly and just curious how...

Neighbor brought over this Honda generator since it would not start. Checked compression and is 60 PSI. Squirted a little oil in spark plug hole and compression increased to 90 - 95 PSI which I think points towards bad rings or scored cylinder. Question is can oil also help seal a valve seat on...

I am approaching 800 hours and the service manual says should check valve clearances. Problem is the service manual I have is just the Chasis and does not cover the engine much to my surprise.. Questions I have are: 1) what is the valve clearance specs for this model? I believe 2013 model year...

I am working on an older 12 HP Briggs Model 281707-0411-01 that does not appear to have any compression release. The starter turns till compression stroke and stops. I have verified battery voltage and all electrical connections. Actually hooked my battery charger with boost direct to starter...

Working on a 2011 GP5500 that is slow to start and in performing compression test I get 50 - 55 PSI max. Put a couple squirts of oil in cylinder and compression did not improve. Checked valve clearances and intake is .010 exhaust is .015 so I believe that should be adequate but don't know...

I am working on a 2002 X495 with Yanmar 3TNE74C engine where temp gauge is erratic. I have service manual for X749 and its shows temp sensor resistance should be 40 - 700 ohms. I looked at Deere parts and both models show using Temp sensor P/n T110736 so am I correct to presume the ohms should...

I have been performing multiple google searches and have been unable to determine what type of tree or shrub this is. They have clusters of nut ranging from 2 to 5 per cluster. They are approximately 12 - 15 feet high with multiple shoots vs one trunk. Squirrels love the nuts and I find husks...

Did anyone else get a recall letter for their 2400, 2510 or 2610 about an emissions recall? I am curious since letter I received states not getting work done could be considered improper maintenance which I suspect could effect warranty. Mine is out of warranty so not a big concern. States will...

Engine is Kohler MV18S opposed twin: Crankcase was full of oil and gas mixture so drained the oil, refilled with new oil. Engine started and ran fine while I looked for any gas leaking around fuel pump and watched for evidence of carb over flowing. After running for several minutes shut engine...

My Kats 11407 block heater has failed for the second time in 7 years of ownership approx 650 hrs on the clock. Is anyone else experiencing these failures? First unit solder joint failed on one of the pins. This unit heating element must have burnt out since get infinite ohms across the pins...

What IP rating is recommended or required for actuator use on snow blower chute deflector? I have seen IP54, IP65 & IP66. Will be mounted rod down to limit water running in around the shaft.

Morning all, Can anyone tell me if there is a operators manual available on-line for the 870 Ecolo-Tiger disc ripper. I am helping my neighbor do some field work with this implement he just purchased and we need help on some of set-up functions. Biggest question we have is there is a red / green...

I have a 2013 X540 with FD731V-HS02 engine. It has been starting to run rich so looking at new float needle. In looking at the parts diagrams it appears that the float needle is only available if you also buy the float assemble AM132296. Can anyone tell me if the needle is sold as a separate...

Can new clean 6061 - T6 be welded using a stick welder? Reason for asking is that my son & I purchased an aluminum frame trailer and we are debating different ways to attach a hand winch that keeps steel away from the aluminum to reduce or eliminate the galvanic action potential of road salt...

Does anyone know who builds Chase utility trailers? I have tried multiple internet searches with no success. Reason for asking is that I stopped and a trailer dealer in Fulton, IL and they carry the Chase brand. These trailers have a couple of features I liked and some other features that...

For reference this is a 94 0r 95 3445 with Kawasaki FD590V engine and 813 hrs on the clock. This mower may run for 5 minutes or 1 1/2 hrs before it just randomly stumbles or just quits with no warning. Some times it will restart and other times it will not. First time it did this I saw inlet...

Engine Kawasaki FH531-AS04 On this 325 if I remove the black wires (3/16 side connector) from the ignition coils I get full spark and the engines runs fine. Connect the black wire and the spark is cut. I do not have the service manual for the 325 and I could not trace the wires back. I do have...

Trying to help a friend diagnose the problem with steering on his GT1554. While driving forward everything tracks fine. Back up and both front wheels toe in to the point they leave scuff marks on concrete. We replaced the plastic bushings in the drag links and both tie rod ends. This helped a...

Can anyone provide a general idea on possible model numbers for this rotary cutter. Their is a name plate on the gear box that says International Harvester but I could not see any model number referenced. This is a 5 ft cut and I believe that it has been repainted from a darker yellow / tan to...

Friend has 425 the just started to run away. We have checked & rechecked all of the throttle and governor linkage finding nothing binding or broken. Hve checked and checked the governor adjustment (everything full CCW) All springs in place but engine still will not stay at an idle unless you...

Hi all, has any one added tail lights to their X5** series of tractor? I never paid any attention during the summer but noticed today that there are no tail lights on these and when plowing snow in the dark by the county road tail lights would be nice. Can I just tap into the head light...

Does anyone have any idea on the brand of HST's used on a woods 3150 mow n machine. Neighbor has one were the right side drive quit working and I can't find any numbers on it anywhere. We have not removed the drive from the frame since I suspect the repairs may cost more than the machine is...

Well finally decided that the old 112 was beyond the point of economical repair so purchased a 2013 X540 as a replacement. If this X540 lasts half as long as the 112 it will outlast me.. Aa a side note the MC519 collection system is for sale.

Hopefully this isn't a repeat question but what were the major changes made between the 2006 - 2010 models and the 2011-14 models. Tractor data shows the 2011-14 models are around 80 lbs heavier with a different model Kawasaki engine. Tractors in my area: 07 433 hrs 48" deck $4,100 07 638...

Does anyone else have a Butterfly Bush that is not showing any new growth yet? Ours is three years old and last two years it was 6 foot tall and blossomed out real nice. It was trimmed back last fall after a killing frost just like previous years. Wife wants to dig it out but I am trying to...

Hi all, working on a friends mower that started leaking oil real bad. I found the seals in the oil pump were leaking by running the oil pump with an electric drill. Replaced these seals and now have much smaller slower leak that I can't find. Leaves about a 3" diameter spot on the concrete...

Does anyone know of any requirements for figuring the recommended minimum spline engagement for pump drives? I.e. 1 x shaft diameter, 1 1/2 x's, etc...

Neighbor called and asked if I could feed his horses and plow his drive since he was snowed in and his kids place down south. - 6 today so I plugged her in for a couple of hours and it started right up. Left it sit and idle for about 8 minutes while I put on the insulated coveralls, etc. Drove...

Can anyone tell me what size or displacement the Rancher 61 is? I have an old one that I am afraid is on its last legs and want to make sure I replace it with something of equal power or more. Currently have 20" bar and quite frequently wish it was a 24" for the larger trees that seem to be...

I recently purchased a used woods LR72 landscape rake and the gauge wheels are low. Does anyone know what the pressure should be in these wheels. I was some what surprised that they are even pneumatic. TIA

Will a landscape rake remove the weeds in gravel driveway Vs having to spray them? Looking for a solution that will do some minor grading/ cultivating and weed control all in one pass. I am not a big fan of chemical weed control. Would the ETA rake be better choice Vs King Kutter for some thing...

Hi all, Has anyone found a deterrent for the Japanese Beetle invasion? I have six Horst Chestnut bushes that they seem to love. These bushes are around 20 -30 feet from my garden so I don't like to use to many harsh insecticides. Currently I have been going out morning and evening and shaking...

Can anyone suggest a source for a sub-soiler point / shovel to fit on a Taylor Pittsburgh middle-buster. I have tried the local Farm & Fleet, New Holland dealer and no one carries cultivator shovels anymore. Needs to be a minimum of 2" wide and 2 1/4" bolt centers. TIA

I purchased a set of drive-in style forks ( see picture) and have to weld the hooks onto the top of my FEL bucket. Bucket is 3/16" thick and 6" flat area for the hooks to be welded too. Would using 6011 for root pass and 7018AC for the top pass be the correct choice of rods for doing this or...

Hi all, I seen several posts about clamp-on and quick tach forks but have not seen one about the drive-in style. This is the type where there are three or more hooks welded to the top of the bucket and you tilt the bucket forward, drive under the fork shaft, roll the bucket back and the forks...

Rear tires on my 2400 Branson are 9.5 x 16 R1's and I have performed multiple searches on trying to find inflation charts but could not find one for this size tire. Owners manual says 28 PSI which makes the tires way to hard. Tractor weighs 1800 lbs without FEL or MMM. Trying to determine what...

Hi all, I have been considering getting the rear tires on my 2400H filled and was researching Rim Guard Vs CC (Calcium Chloride) and here is what two different local tire shops told me. Both of these shops are n smaller towns and majority of their tires are large Ag tires. Both of these shops...

Hi all, I have a JD 110 with a Kohler K181 magneto style ignition engine that provides a random spark. Strong then weak then none. Only strong for couple of revolutions. Engine may cough once and that is all. Spark is observed by grounding the plug to the head. Things I have checked or tried...

Just an FYI for anyone that lives in colder climate the safety switch on clutch may stop working on these in cold weather and tractor will not start. Mine failed today and dealer said he had another one fail yesterday. Takes very little heat and the switch will operate again. Going to tear one...

On my 2400H the front wheels just randomly stop turning and slide when in 2WD. All three times it has done this is when taking off from a dead stop or stopping to change direction of travel. There is no clicking or crunching noises. I have jacked up the front wheels and spun them by hand and...

Hi All, I was curious if anyone has had control / feathering problems with their control valve on the BL00 loader. Reason for asking is the valve on my 1200X is terrible. I finally used it for moving some dirt last weekend and their is absolutly no feathering of the lower or dump function with a...

Well last night dealer called and said they had replaced the steering control valve on the 2400H so I took it out for a test drive around the lot and then brought it home with me. Since we have company coming today I had to get the lawn mowed so pictures will have to be posted later today...

Hi all, Test driving a new 2400H for about three hours saturday, total of 7 hrs on the hour meter, and have the following concern or question. The steering feels sloppy like an old manual steering system where you constantly have to correct your direction of travel. Also when mowing I noticed...

Just a couple of pictures showing the difference between the BL00 and the 1200X FEL. NOTE: The 1200X does NOT have a quick tach bucket. The cylinder geometry difference explains the lifting capacity difference. I will probably be bringing the 2400H withe 1200X home unless the MMM turns out to...

On a 425 with the Kawasaki 20 HP FD620 (I think, label is faded and scratched) engine what is the correct valve clearance spec? I have found three different specs. One said both at .004, one said both at .010 and one said intake .005-.007 exhaust .008-.010. I believe the last one of .005-.007...

Hi all, does anyone have any experience with the MMM option on the 2400 or 2800 tractors? Dealer does not have one on the lot and the sales brochure doesn't answer these questions. Interested in how easy or hard it is to attach and remove the MMM. I.e. pull a couple spring loaded pins and slide...

Hi all, I have no knowledge of the Massey line up so please be gentle. I presently own a Kubota BX1850 and do to my needs changing am looking at a Kubota B2320 or JD 2320. Require MMM and FEL. Would like to stay in the 23 - 26 HP range. Tranny - HST or manual. Prefer to stay around 50" wide...

I have a couple of questions on removing the fenders and floor pan on my BX1850. 1) How does the speed adjusting knob for the 3PH come off. I can not see any jam nut against the end of the plastic and don't like the idea of pliers and pray something don't break. 2) Floor pan, does the plastic...

Hi all, Can some one take a couple of pictures of how long the chains on the discharge of their rotary cover are. Do they hang down about even with the bottom of the deck? I have an old 5/16" log chain that has a couple of stretched links and plan on cutting it up for the discharge and inlet...

Hi all, looking for guesses on what mix this dog is. Mother is full blood Beagle and father is??? She is about 15 months old in this picture. The Fat male Beagle in the second picture is also full blood Beagle and stands about 16" high at the shoulder & weighs around 45 lbs for a size...

Hi all, can some one tell me how the HP requirements for a flail mower Vs bush hog compare under the same operating conditions. Does the flail type leave less bunching and clumps? I may have to maintain my pasture this year which means mowing an extra 2 acres at least three times during the...

Hi all, Installed one of these lower radiator hose heaters in my BX and now it appears that every time the thermostat calls for heat there is a high inrush current that is tripping the circuit breaker. The heater is 350 watts at 120 VAC and when oerating it draws between 3 & 4 amps per my amp...

Has anyone installed one of the factory block heater kits on their BX18**. I purchased one of these kits and the pictures are black and impossible to identify any components. Was hoping someone could possibly post a couple of pictures showing how this unit is mounted and plumbed. If not I will...

Hi all, In the process of removing the engine from the plastic frame due to punching a hole in the gas tank. In looking at the chain oiling system is there any spring loaded parts that will fly out when pulling the engine from the frame? I have all the other items removed but can't determine...

Good friend has a 425 that will not shut off unless we disconnect the battery cables. We have tried disconnecting the ignition switch with no change. When you touch the battery terminal their is a spark and an audible click almost like the starter solenoid but it isn't. Any suggestions on where...

Hi all, neighbor asked me to look at their mower since it was not cutting evenly. New Toro blades P/n 106-2247-03 where installed recently with little or no change in performance. They are using this as a mulcher and it appears like once they get into grass of any density or height the right...

Hi all, my pumpkin plant leaves are getting a whitish grey growth on them almost like frost or mold. Seems to be spreading from the main vine outward. I do not see any evidence of the leaves being eaten by bugs. Any ideas on what this is and what the cure would be? Was going to take some...

Working on Ferris with the Kawasaki FH641V engine charging system. Battery will not stay charged and I have performed the following diagnostic tests. Cleaned battery terminals: Note engine spins over fine when the battery is charged so don't think it is a battery issue. I have checked the...

Neighbor has a 410C with MFWD and the steering is very erractic. Symptoms are: Steering wheel turns freely but the wheels do not turn. This happens steering in both directions. This becomes more prevalant as the oil gets hotter. I do not have a schematic or service manual to see what and or...

Neighbor was cleaning out his grove and had an older Ford Disc and I think the tag says it is a model 221. (Name plate was pretty beat up). He thought his dad used to pull it with an 8N or 9N but wasn't sure. It is 3PH and measures approx 5' wide with 20" blades. Has the option of allowing the...

Hi all, I just purchased 5 lbs of E6011 3/32 diameter and am having tremendous problems getting it to hold an arc. It wants to short out and stick. I have tried flat, vertical up, vertical down, with Vertical up being the least likely to stick but it still does. Very difficult to strike arc...

Can any tell me if the BX fuel filters are also water absorbing? Reason I am asking is mine plugged again. Temperature was upper 20's and when I removed the inlet hose the fuel ran out like a garden hose. Fuel in filter was also fluid and it poured out but i could not blow through it either. i...

Looking at putting some form of depth limiting device on my plow and am looking into the pros and cons of shoes/skids vs. caster wheels. My initial thoughts are: Cons: Shoes/skids: wear along with cutting edge so the yboth may require replacing around the same time. Would they have a tendancy...

Can anyone tell me if the cutting edge on the Suburbanite is considered reversable. I have looked at Westerns web-site and could not find any mention of this in any of their literature. Looking at it I would guess it is not but am hoping someone with more knowledge can confirm or deny this. I...

Hi all, are these written for the average shade tree mechanic or more for trained shop personnel? Thinking about getting one for my BX and would like to know if they are money well spent, or just spent money. Reason for asking is that I have the factory manual for my BMW motorcycle and it is...

I have been working on a cure for the sudden stop on the 50 series and would appreciate an answer to these questions from someone who has a 60 series. When backing up and you, the operator move the trundle to neutral quickly am I safe in presuming you will also get the abrupt stop? From full...

Hi all, I have done some searches on this and found some pictures but could not find anything that gave me deffinite answers to how these mount so here goes.. Reason i am asking these questions is that my son has a plow that came off of a JD 2305 with the JD quick-hitch assembly. I am going to...

Hi all, I had to replace one of my front tires so I ordered a new tire from the dealer. Checked with local farm tire dealers and none of them carried that size. When it arrived I noticed the tread design and size where both different. Original tire was a 16 x 6.50 x 8 and the new tire is a 16 x...

Hi all, starting to do some research on weed control methods for up to 2 1/2 acres of lawn pasture/hayfield. Weeds of concern are: Thistles, neighbors pasture is full of them and they are starting to spread to mine. Cockle burrs / Bordock: So far these are limited to a couple of small areas...

Hi all, Finally worked my BX1850 hard enough last night that is was getting warmer than normal and I was going to clean the screen and it would only come out part way. Should this screen in front of the radiator pull all the way out or does it have a safety catch to prevent it from being...

My local Kubota, MF, Agco dealership was broken into last week and the thieves where prepared. They backed at least one semi upto the building and using the companies fork lift proceeded to load up lawn mowers, A couple of CUT's, parts, cases of oil etc. Not sure what the thieves are doing...

Hi all, I have a few questions about lawn aerators that hopefully some of you can answer. Purchased this home last fall and I am going to be landscaping and reseeding most of my lawn this fall and I am looking into which tools would be the best choice to to try and rent or purchase. Ground is...

Hi all, I have been looking around at rental shops here in northern Illinois for the following equipment to use with me BX1850 and have not been able to find a source. Can you rent this stuff in your area? Question: How much weight can reallistically be carried on the 3PH. I know specs say...

The attached picture is an example of what happens to HST when they are run low on oil or started and operated on cold mornings I.e. growling at you. This pump came of a test stand where I work. This is not an oil cleanliness issue since we test all of our stands on a monthly basis. Roy

Hi all, I found the dimensional specifications ISO 730-1 for tractors showing lowered lift Arm max height of 200 mm (7 7/8"). On my BX they are 9 1/2 - 10 1/2" depending of if the FEL is on the ground or not. Does anyone have the specs for placement of the attachement point for the implements...

I have a problem with my BX1850 in that the fixed length 3 pt arm does not lower enough for my box blade to touch the ground. I have seen some posts about using log chain to replace the rigid lift link. On my BX if you take the lift link off the main arm wants to twist sideways. I know that when...

As a fairly new owner of a Kubota I am not sure how well these little devils start but.... to me mine is a cold blooded beast. Yesterday temperatures in the middle 50's had been working it pretty steady for about 45 minutes digging a hole with the FEL and moving dirt in general. Shut the...

Hi all, I have been working on the sudden stop issue on my BX1850 which seems to effect most of the 50 series models. I have made adjustments that have taken the sudden stop out of the equation. Problem is that some times now it won't stop at all. I am trying to find photos of the HST linkage...

I have done several searches and read posts about putting a block heater in the 30mm freeze plug behind the muffler. I have looked at my BX and question if there is enough room. Has any one installed one there BX1850? Dealer sells some type of heater that looks like it connects to the side of...

Hi all, does Kubota supply owners manuals with their FEL's and MMM? I received the the manual for the BX1850 but did not get manuals on the LA203 or the 54" MMM. Should I be asking the dealer to supply these. I purchased the tractor used so I would suspect any manuals are still in the posession...

As requested here is a picture of my new to me BX1850 and my old JD 112. It is about 450 ft to the back fence so they should have room to roam. Lessons learned in the first few hours of use. 1) You can press all day long with your left foot and never find the clutch.:o 2) Pressing on what used...

Well I pulled the trigger tonight and bought a BX1850 with 54" MMM and FEL. Now before flame throwers start on me about the title of this thread, it got your attention didn't it.:D Light switch is defective so unable to turn off the flashers. Dealer has new switch on order and will install it...

Hi all, I am looking at an 06 BX1850 with 236 hrs on the clock. It has the FEL and a 54" MMM. Only items I have seen to check on are: Plastic deck ( operators floor board) cracks and there is supposedly a newer design. Is this true? I have read about the jerky reverse concerns. I have driven...

Hi all, newbie looking at a Kubota BX1850. Plan on doing some research in the Kubota section and possibly even ask some questions. Roy the old n